Swan SI9031N steam ironing station
Contents
1. After use Set the temperature control dial to MIN position and place the iron back on the iron rest plate Switch off the unit by pressing the power switch and then unplug the appliance from the outlet Slide out the water tank and pour out the remaining water Note a For every first time use it is normal that a slight vibration sound may be heard from electrical pump inside the base unit for about 10 seconds when steam ironing started It is because there is air inside the filter it will stop when the air inside the filter has been pumped out If this sound continues for more than 30 seconds please check whether water tank and filter are assembled correctly or not During use if steam stops along with 5 BEEP sound alarm or water tank indicator light and water filling indicator light on control panel blink This indicates that it is time to fill water tank For continous use of steam ironing sometimes pump working indicator light will turn off for several seconds steam also will stop for several seconds This is normal It is because anti drip function has been activated to protect leakage from soleplate Dry ironing 1 Connect the appliance to a suitable socket outlet Press power switch on control panel a Beep sound will be heard and the power indicator light lights up It shows that the unit has been connected to the power supply Press steam selection switch to turn off all 3 steam indicator lights it is ready2. by lower temperature such as nylon etc immediately It is advisable to adjust the temperature button to the lower setting waiting for about 2 4 minutes till the power indicator light turn off and then you can start ironing IMPORTANT HINTS Do not fill water tank with vinegar perfume starch chemically descaled water or descaling agents How to use your steam generator Prepare the appliance for use 1 Check if the rating indicated in the rating plate corresponding to the main voltage in your home 2 Press handle buttons to lay handle down Fig 1 Note When handle is up the unit is shut off it will be ON when handle is laid down 3 Remove any protective foil or sticker or card from the soleplate 4 Fully unwind and straighten the power cord and the supply hose 5 Place the appliance on a stable level and horizontal surface such as ironing board 6 Place the iron onto the iron rest plate horizontally at the base unit Fill water tank 1 Press the water tank lock upwards and slide the detachable water tank outwards from the base Once power on water tank indicator light will turn off while water tank is sliding out Fig 2 2 Take the filter upwards out from the water fill hole You can take the filter out of the opening for filling water into water tank or fill water into water tank directly with the filter existing in the opening Fig 3 3 Fill the water tank up to or below the MAX fill line
3. fabric setting chart is only valid for plain fabrics and not for materials to which finishes glosses etc have been applied Textile to which some kind of finish has been applied gloss crinkle relief etc is best ironed at lower temperature 3 First sort laundry according to ironing temperature setting guide wool with wool cotton with cotton etc 4 The iron heats up more quickly than it cools down Therefore start ironing articles that need to be ironed at the lowest temperature such as those made of synthetic fibres 5 lf the fabric consists of various kinds of fibres always select the temperature required by the most delicate fibres i e the lowest temperature If for example an article consists of 6 0 polyester and 40 cotton according to the fabric setting chart it should be ironed for polyester and without steam 6 If you do not know what kind of fabric the article is made of iron a piece of the material which is not visible when you wear to find out the appropriate temperature for your articles 7 Pure woolen fabrics 100 wool should be ironed with the iron setting to steam ironing position It is advisable to set the temperature control button to Max position and use a dry pressing cloth 8 When steam ironing woolen fabrics shiny patches may occur You may prevent this by turning the article inside out and ironing the reverse side 9 After using of steam ironing for cotton fabrics do not iron articles required
4. for dry ironing Set temperature control dial to desired position according to above fabric setting chart Temperature indicator light in iron unit will light up to indicate that the steam chamber being heated up When temperature indicator light turn off it indicates that desired temperature has been reached it is ready for dry ironing During use it is normal that heating indicator light will cycle from on to off and then off to on This shows that steam chamber automatically keeps temperature constant During use please press steam lock every 15 minutes Otherwise iron will automatically shut off Refer to auto shut off function After use Set the temperature control dial to MIN position and place the iron back on the iron rest plate Switch off the unit by pressing the power switch and then unplug the appliance from the outlet Note When changing your Temp setting from higher setting to lower it is advised not to start ironing immediately since it may cause burns to your fabrics Please wait until temperature indicator light lights up steadily and then start ironing How to use your steam generator Vertical steam ironing Follow the steam ironing process and then hold the iron 5CM 15CM in vertical position between 5cm and 15cm away from the hanged fabrics Fig 6 Press the steam button and then will create vertical steam This feature is especially used for removing creases from hanging clothes and curtains Never s
5. SET designed for life Steam Generator Model SIS031N Important safeguards PON 10 11 12 13 21 22 Make sure to read all the safety precautions below and look at the illustrations before you start using the appliance Use the appliance for its intended use only The appliance is intended for household use only In order to protect against the risk of electric shock do not immerse iron power base into water or any other liquids Connect the appliance only to an alternating current of the voltage specified on the rating plate and only to an earthed socket To avoid a circuit overload do not operate another high wattage appliance in the same circuit Never yank cord to disconnect from outlet instead grasp plug and pull to disconnect During use do not lift the appliance by power cord supply hose Always disconnect the plug of the appliance from electrical outlet when filling with water or emptying and when not in use Do not operate the appliance with a damaged cord or if the appliance has been dropped or damaged it must be taken to a qualified serviceman or manufacturer or its service agent for examination and repair Incorrect re assembly can cause a risk of electric shock when the iron is used Keep the iron and its cord out of reach of children less than 8 years of age when it is energized or cooling down During use always place the power base on a stable level and horizontal surface or iro
6. e filter in water for several minutes before installing it into the water tank Connect the appliance into a suitable socket outlet Press power switch on control panel a Beep sound and the power indicator light illuminates it shows that the unit has been connected to the power supply Water tank indicator light will also light up Heating indicator light will turn on to indicate that the steam chamber being heated up Low steam setting indicator light turns on to indicate steam is set at low setting During use it is normal that heating indicator light will cycle from on to off This shows that steam chamber automatically keeps temperature constant Set temperature control dial to steam ironing position according to fabric setting chart mentioned above Heating indicator light at iron unit turns on to indicate the unit being heated up When the heating indicator light turn off the desired temperature has been reached It is ready for steam ironing Before every first time use it is advised to clean iron unit as follows Take the iron up from the base unit press steam button underneath the handle to allow steam ON for 20 seconds and then OFF for 30 seconds this cycle should be repeated for 2 times Wait until temperature indicator light turn off it is ready for use 6 7 How to use your steam generator 5 During steam ironing please adjust steam rate according to your requirement as indicated in the steam function setting
7. intenance shall not be made by children without supervision Parts and Features Water tank Handle Soleplate Heating indicator light Steam button Steam button lock Steam button Temperature control dial Power cord Supply hose 10 Power cord 11 Handle Button 12 Heating indicator light Power base 0 C0 NO O1 OA Pump working indicator light Filling indicator light Filter replacement indicator light Power ON OFF Power indicator light Steam selection switch High steam setting indicator light Medium steam setting indicator light Low steam setting indicator light Control panel Water tank release Filter Water tank indicator light Fabric Setting Chart Temperature Setting SYNTHETIC WOOL SILK COTTON Linen Max Fabric Synthetics Silk Nylon Arcrylic Acetate Wool Polyester Rayon cotton Linen Rayon cotton Linen Ironing Instruction Steam Selection Dry Iron on the opposite side of the fabric Use a press cloth and Steam Iron on the opposite side of the fabric Iron while fabric is still damp Temperature control dial Steam Ironing lroning Temperature Setting Guide 1 Follow up the ironing instructions on the garment label If there is not any instruction label but you know what the fabric is please refer to the fabric setting chart described in this instruction manual 2 The
8. n lock is locked for a long term Release the steam button lock so it can resume a Fig 13 Use of the handle Handle attached to the base unit used for carrying the appliance it also serves as a power on off switch Lift the handle up to power OFF Lay it down for power ON Before use please lay the handle down as following method Press two handle buttons at the same time to lay down the handle Fig 14 After use allow the appliance completely cool down Fig 15 put the iron onto power base Lift handle up There will be a click sound to indicate the handle has been locked in place and you can carry the appliance by the handle Emptying and storing 1 Disconnect the appliance from the power supply and allow the appliance to cool down for 60 minutes at least 2 After use slide out the water tank and pour out all the remaining water Fig 16 3 The iron should be place on the iron rest plate and then stored Cleaning and Maintenance 1 Unplug the appliance from the main supply and let the iron completely cool down 2 Clean the iron with a damp cloth 3 Wipe off scale and any other deposits on the soleplate with a damp cloth or non abrasive liquid cleaner Fig 17 4 Never clean the appliance under the tap Fig 17 lt gt Trouble shooting Problems Possible causes Solution Iron won t heat Incorrect connection to the main socket Re plug the unit to main socket Temperat
9. ning board and then place the iron on the power base Place the iron on the power base Do not allow power cord or supply hose to touch hot surfaces Burns can occur from touching hot metal parts hot water or steam Use caution when using the appliance If the iron is placed onto the iron rest plate during in use the iron rest plate may become a hot surface Do not touch the iron rest plate and the soleplate until they have cooled down completely Never use the iron facing towards people because the steam can cause burns Never twist the supply hose during use The iron must not left unattended while it is connected to the supply mains The appliance must be used or stored in a level and horizontal surface When placing the iron on its stand ensure that the surface on which the stand is placed is stable The iron is not to be used if it has been dropped if there are visible signs of damage or if it is leaking If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and konwledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user ma
10. r several minutes in order to gain better performance for future use 3 After power up press steam selection switch and Power ON OFF concurrently Fig 12 filter replacement indicator light will stop blinking and return to checking mode Anti calc system 1 The filter is designed to reduce the build up of limescale which occurs during steam ironing this will prolong the working life of your iron However please note that the filter will not completely stop the natural process of limescales build up 2 After the filter is invalid even if a new one is not available at that time The filter can still be used continuously However limescales may be most probably built up in steam chamber This happens depending on your local water quality t is advised that filter is replaced as soon as possible or use bottled water Safety protection device This appliance has a safety protection device in the base unit If the supply hose is blocked accidentally the safety valve will be opened to release steam from the safety vents under the base unit along with high pitch sounds Once this happen unplug the appliance immediately and check whether any damage is found in the supply hose Auto shut off function The iron will auto shut off after 20minutes if the steam button is not pressed All indicator lights OFF Press Power ON OFF to turn the iron back ON for resuming Note Auto shut off function will not be activated if the steam butto
11. re the steam button is set at steam ironing position and steam indicator light is ON
12. team garments whilst wearing them Note 1 During steam ironing supply hose is very hot please do not touch it 2 Never block the steam hose Auto locking function for steam button If long time steam ironing is needed please press down steam button lock and then push it backwards steam button will automatically lock Steam will escape continuously If you want to stop steam please push steam button lock forward Note Once steam button auto locking function is activated do not leave iron unattended Water filling indication function No water or water not enough in water tank water tank indicator light and water filling indicator light on control panel will start blinking concurrently Fig 7 5 BEEP sounds alarm to indicate filling is needed How to use your steam generator Filter Replacement 1 A filter checking system is built into this appliance It can detect the working time for nae the filter Once the filter is invalid the filter replacement indicator light on control panel s will continuously blink to indicate that the l Pume f4 filter needs to be replaced Fig 8 2 Replacement Method Slide water tank out Reet pe from base unit Fig 9 take the filter out sor from water tank Fig 10 and then replace with a new one Fig 11 After new filter has been installed into water tank fill water tank to Max fill level and then slide tank back into base unit Immerse filter in water fo
13. ure setting knob is set at O position Set to the required position Power OFF Switch the appliance ON Handle has not been laid down Lay handle down Unknown malfunction Take it to qualified service man or manufacturer for repair Water tank light blinks Two BEEP sounds alarm when pressing the steam button No water or not enough water in water tank Fill water to water tank as described in Fill water tank Droplets of water escape from the soleplate Temperature control dial is set at low temperature position Set temperature setting knob to suitable position refer to Fabric setting chart The set temperature has not been reached or is too low Allow sufficient time for iron to preheat or set higher temperature Steam is set at higher position Set to lower steam setting Water tank decoration indicator light OFF Water tank has not been installed in place Well install the water tank Filter is missed to install Un known malfunctions Install the filter Take it to qualified service man or manufacturer for repair All indicator light OFF The appliance comes into auto shut off mode Press power ON OFF to reset it Iron does not produce steam The set temperature has not been reached Allow sufficient time to preheat until heating indicator light turn off Steam button is not set at steam ironing position Ensu
14. with clean water Fig 4 Replace filter back into water filling hole Replace the water tank into the base unit again It will be locked in place with the base unit when a click sound is heard Water tank indicator light will light up to indicate that water tank and filter have been installed in place Power will then be ON Fig 5 6 Always pour out the remaining water after use o gt How to use your steam generator Functions for Water tank indicator light 1 After power On water tank indicator light will light up Water tank indicator light blinks to show that no water or not enough water is in the tank please fill water to Max level After filling with water water tank indicator light will light up steadily for easy viewing of water level Water tank indicator light will not light up when water tank or filter are not properly in place and no steam function even if steam button is pressed BEEP sounds from base unit if tank or filter are not properly fitted Steam function setting Once the unit energised with power steam indicator light automatically sets at low steam setting Press steam selection switch to change to MAX or Medium steam setting If steam ironing is not necessary please turn off the steam selection switch and wait for all steam indicator light to go out Steam ironing 1 Fill water tank with clean water refer to above filling instruction For better performance please immers
Download Pdf Manuals
Related Search