Bosch WAT24460GB washing machine
Contents
1. Register your new Bosch now www bosch home com welcome Washer WAT en Instruction Manual and Installation Instructions Your new washing machine You have selected a washing machine from Bosch Please take a couple of minutes to read and become familiar with the advantages of your washing machine To meet the high quality demands of the Bosch brand each washing machine that leaves our factory is inspected thoroughly to ensure that it functions properly and is in perfect condition Additional information about our products accessories spare parts and services can be found at www bosch home com or contact our customer service centers lf the instructions for use and assembly describe various models reference is made to the differences at the appropriate places L Do not start up the washing machine until you have read these instructions for use and the installation instructions Explanation of symbols A Warning This combination of symbol and signal word indicates a possibly dangerous situation Not heeding the warning can cause death or injuries Caution This signal word indicates a possibly dangerous situation Not heeding the caution can cause property and or environmental damage Note Tip Instructions on how to best use the appliance as well as other useful information 1 2 3 a b Action steps are indicated using numbers or letters a Li2. m 2 The volume of the information signals and or m 3 The volume of the button signals O off 1 quiet 2 medium 3 loud 4 very loud Exiting setting mode You can now end the process and set 20 the program selector to the Off position The settings are saved Cleaning and maintenance Z Warning Danger of death There is a risk of electric shock if you touch live components Switch off the appliance and pull out the mains plug Z Warning Risk of poisoning Toxic vapours can be produced by cleaning agents that contain solvents e g cleaning solvent Do not use cleaning agents that contain solvents Caution Damage to the appliance Cleaning agents that contain solvents e g cleaning solvent can damage Surfaces and components in the machine Do not use cleaning agents that contain solvents Prevent detergent residue from building up and odours from forming by following these instructions Notes m Ensure the room in which the washing machine is set up Is well ventilated m Leave the door and detergent dispenser tray open slightly when the washing machine is not in use Occasionally run awash using the 4 Cottons 60 C programme and powder detergent Machine housing control panel m Wipe the housing and the control panel with a soft damp cloth m Remove the detergent residue immediately Do not clean with a water jet Drum Use chlorine free cleaning agents do
3. Note To prevent foaming only use half the amount of detergent recommended by the detergent manufacturer Do not use detergent designed for wool or delicates 10 Close the detergent drawer 11 Press the Dll button 12 When the program ends switch off the appliance Your washing machine is now ready to use no Feo Me Pm 34 Transportation e g when moving home Preparatory work 1 Turn off the water tap 2 Reduce the water pressure in the supply hose Maintenance filter in the water supply gt Page 22 3 Drain the remaining detergent solution Maintenance detergent solution pump blocked Page 21 4 Disconnect the washing machine from the mains 5 Remove the hoses Installing the transport locks 1 Remove the covers and keep them in a safe place Use a screwdriver if necessary 2 Insert all four sleeves Clip the mains cable securely in the holders Insert and tighten the screws Before switching on the appliance again Notes m he transport braces must be removed Positioning and connecting en m o prevent unused detergent from flowing straight into the drain during the next wash Pour approx 1 litre of water into compartment Il and start the Y Drain Empty program 35 Aqua Stop warranty Only for appliances with Aqua Stop In addition to warranty claims against the vendor based on the purchase agreement and to our appliance warranty we will provide compensatio
4. Programme end End appears in the display panel and the indicator lamp of the Dil button is off Removing laundry switching off the appliance 1 Open the door and remove the laundry 2 Turn the program selector to Off The appliance is switched off 3 Turn off the tap Note Not required for Aqua Stop models Notes Do not leave any items of laundry in the drum They may shrink in the next wash or discolour another item m Remove any foreign objects from the drum and the rubber seal risk of rusting m Wipe the rubber seal dry m Leave the door and detergent drawer open so that any residual water can evaporate Always wait until the program ends as the appliance could still be locked Then switch the appliance on and wait for it to unlock Ifthe display panel goes off at the end of a program the energy saving mode is active Press any button to activate the panel Sensors en Sensors Automatic load sensing The automatic load sensing function adapts the water consumption ideally to each programme depending on the type of fabric and the load Unbalanced load detection system The automatic unbalanced load detection system detects imbalances and ensures even distribution of the laundry by repeatedly starting and stopping drum spinning If the laundry is extremely unevenly distributed the speed is reduced or the spin cycle is not performed for safety reasons Note Place large and
5. he mains plug fits the socket m he cable cross section is adequate m he earthing system is properly installed m Ihe mains cable is only replaced by a qualified electrician if this is necessary Replacement mains cables are available from the after sales service No multiple plugs couplings or extension cables are used m lf an earth leakage circuit breaker is used only a type which displays this symbol is used KX Only this symbol guarantees compliance with the currently applicable regulations m Ihe mains plug can be accessed at all times m he mains cable is not bent squashed modified cut through or in contact with heat sources 33 en Positioning and connecting Before washing for the first time The washing machine was thoroughly tested before leaving the factory To remove any water that may be left over from the test run the first wash cycle without any laundry Notes m The washing machine must be correctly installed and connected from Page 27 m Never use a damaged machine Inform customer services Check the machine Remove the protective film from the control panel Connect the mains plug Turn on the tap Close the door do not load any laundry Depending on the model run the Drum Clean 90 C or Cottons 90 C program Open the detergent drawer Pour approximately 1 litre of water into compartment II 9 Pour standard detergent into compartment Il
6. not use steel wool If there are odours in the washing machine or to clean the drum run the Drum Clean 90 C or Cottons 90 C program without laundry Add washing powder Descaling Descaling should not be necessary if the detergent is measured out correctly However if it is required follow the manufacturer s instructions for the descaling agent Suitable descalers can be obtained via our website or from our after sales service Detergent drawer and housing If the washing machine contains detergent or fabric softener residues 1 Pull out the detergent drawer Press down the insert and fully remove the drawer 2 To remove the insert Push the insert upwards from below with your finger Cleaning and maintenance en 3 Clean the detergent dispenser tray and insert with water and a brush and dry it Clean the inside of the housing as well 4 Fit the insert and lock it in place push the cylinder onto the guide pin 5 Push in the detergent drawer Note Leave the detergent drawer open so that any residual water can evaporate Detergent solution pump blocked Warning Risk of scalding When you wash at high temperatures the water gets very hot If you come into contact with the hot water you may be scalded Allow the water to cool down 1 Turn off the water tap so that no more water can flow in and has to be drained via the drain pump 2 Switch off the appliance Disconnect
7. the mains plug 3 Open and remove the service flap 21 en Cleaning and maintenance 4 Take the drain hose out of the retainer Remove the sealing cap allow the detergent solution to flow out into a Suitable container Replace the sealing cap and place the drainage hose in the retainer 5 Carefully unscrew the pump cover residual water may leak out Clean the interior pump cover thread and pump housing The impeller in the detergent solution pump must be able to rotate Refit the pump cover and screw it on tightly The handle must be ina vertical position Note To prevent unused detergent from flowing straight into the drain during the next wash Pour 1 litre of water into compartment Il and start the WY Empty programme 22 The drain hose at the siphon is blocked 1 Switch off the appliance Disconnect the mains plug 2 Loosen the hose clamp Carefully remove the drain hose residual water may leak out 3 Clean the drainage hose and siphon connecting piece 4 Reattach the drainage hose and secure the connection using the hose clamp Filter in the water supply blocked First reduce the water pressure in the Supply hose 1 Turn off the tap 2 Select any program except Rinse Spin Empty 3 Press the Dl button Allow the program to run for approximately 40 seconds 4 Turn the program selector to Off Pull out the mains plug 5 Clean the filte
8. Eco setting Note Do not exceed the maximum load Eco Energy optimised washing by reducing the temperature while achieving a washing result that is consistent with the selected program without the Speed Eco setting Press the button to do this First of all you can select the Speed setting If you press the button again the Eco setting is active The respective symbol is shown in the display when the setting is activated If you press the button again no setting is active Easy lron 2 Button depending on the model Reduces creasing thanks to a special spin sequence followed by fluffing and reduced spin speed Note The washing s residual moisture is Increased Water amp Rinse ey Water Plus amp Aqua Plus Rinse Plus wy Mepiooor vep Button depending on the model Higher water level and additional wash cycle for particularly sensitive skin and or for areas with very soft water Prewash Uy NoomAuon Button depending on the model For heavily soiled laundry Note Pour detergent into compartments I and Il Operating the appliance en Operating the appliance Preparing the washing machine Note The washing machine must be correctly installed and connected From Page 27 Connect the mains plug Turn on the water tap Open the door Check that the drum is completely drained Drain if necessary sa alas Select programme switch on the appliance Note If you ha
9. flashes selector adjusted Foam detection gt Page 1 lights up Fault display E Page 24 Signal setting 0 4 Page 20 Laundry Prepare the laundry Caution Damage to the appliance fabrics Foreign objects e g coins paper clips needles nails may damage the laundry or components in the washing machine Therefore note the following tips when preparing your laundry m Empty pockets m Look out for metal items paperclips etc and remove them m Wash delicates in a laundry bag tights underwired bras etc m Close any zips button up any cover buttons m Brush sand out of pockets and collars m Remove curtain fittings or place Curtains in a laundry bag Sorting laundry sort your laundry according to the care instructions and manufacturer s information on the care labels depending on Type of fabric fibre Colour Note Laundry can discolour or not be cleaned correctly Wash white and coloured items separately Wash new coloured items separately the first time you wash them Laundry en m soiling Wash laundry with the same level of soiling together some examples of soiling levels can be found on gt Page 13 Light Do not prewash select the Speed seiting if necessary Normal Heavy Load less laundry select a program with prewash Stains Remove pretreat stains while they are fresh Firstly dab with soapy water do not rub Then wash
10. model Depending on what stage the program is in you can change the set temperature before and during the program The maximum temperature that can be set depends on the program that has been selected Spin speed rom 2TOE0dEc Depending on what stage the program is in you can change the spin speed in rom revolutions per minute before and during the program Setting 0 The rinsing water is drained but there is no final spin The laundry 13 en Additional programme settings stays wet inside the drum e g for items that should not be spun Setting Spulstopp Rinse Stop no final spin The laundry stays in the water after the final rinse You can select Spulstopp Rinse Stop to prevent creasing if the laundry will not be taken out of the washing machine immediately after the program has ended To continue end the program Page 18 The maximum speed that can be set depends on the model and program that has been selected Finished in time An amp n os Before starting the program you can oreselect the program end Fertig in Ready in time in hourly increments h hour up to a maximum of 24 hours To do this 1 Select a program The program duration is displayed for the selected program e g 2 30 hours minutes 2 Press the Finished in time button repeatedly until the required number of hours is displayed 3 Press the Df button The program sta
11. small items of laundry evenly in the drum Page 25 VoltCheck depending on the model The automatic voltage control system detects an unauthorised voltage under usage The colon on the Ready in display is flashing gt Page 10 Once the supply voltage is stable again the colon of the Ready in display lights up Normal mode The detected voltage under usage is indicated in the further program sequence by all three points lighting up in the display Note Voltage under usages can for example result in program extensions and or a non satisfactory spin result 19 en Setting the signal E Setting the signal You can change the following settings m The volume of the buttons and information signals e g at the end of the program and or m he volume of the button signals You will need to activate the setting mode in order to change these settings Positions 1 3 A Activating the setting mode 1 Select the 48 Cottons program to position 1 The washing machine is switched on 2 Press the Df button and at the same time turn the program selector clockwise to position 2 Release the button The setting mode is activated and the oreset volume for the information signals appears in the display panel e g at the end of the program Changing the volume Use the Finished in time or button to change the following settings at the corresponding program selector positions
12. supply hose kinked or trapped The safety function is activated Stop the program Is selected Rinse Stop no final spin gt Page 18 Can the door only be opened by the emergency release gt Page 23 Have you pressed the DO or Finished in time button Is the door closed m Isthe childproof lock activated Deactivate Not a fault the internal motor test may cause the drum to Jerk or judder briefly when the wash program starts m I s selected Rinse Stop no final spin gt Page 18 m Clean the drain pump gt Page 21 m Clean the drain pipe and or the drain hose Not a fault the water is below the visible area m Nota fault the unbalanced load detection system has interrupted the spin cycle because the laundry is unevenly distributed Distribute small and large items of laundry evenly in the drum m Anti crease depending on the model selected m Isthe selected speed too low Not a fault the unbalanced load detection system is adjusting an imbalance m Nota fault the unbalanced load detection system is adjusting an imbal ance by repeatedly distributing the laundry m Nota fault the foam detection is system active a rinse cycle has been switched on Not a fault the program sequence is optimised for the specific washing pro cess This may change the length of the program shown in the display panel m Nota fault the effect of the care product is not affected m Clean the insert
13. the Dll button to do this The Bll button indicator lamp flashes and the machine checks whether it is possible to add laundry lf the following appears in the display panel m the symbol disappears and adding is possible m the symbol lights up it is not possible to add laundry 18 To continue the program press the button Dl The program continues automatically Notes Do not leave the door open for too long when adding laundry as water from the laundry may leak out For safety reasons the door remains locked when the water level or temperature is high or while the drum is turning and it is not possible to add laundry during this time m The load display is not active during reloading Changing the programme 1 Press the Dll button 2 Select another program 3 Press the Dill button The new program starts from the beginning Cancel the programme For programs at high temperature 1 Press the Dll button 2 To cool down laundry Select Rinse 3 Press the Dll button For programs at low temperature 1 Press the Df button 2 geol Spin Drain Spin Empty 3 Press the DII button Programme end during rinse hold appears in the display panel and the indicator lamp of the DII button flashes Continue the program by Pressing the Dll button or m selecting a spin speed or setting the program selector to Spin Drain Spin Empty YY and then pressing the Dll button
14. the transport locks 29 Hose and cable lengths 30 Water inlet 0 0 00 eee 30 Water outlet 0 0008 32 EV CMI ris sack bates oe i 33 Electrical connection 33 Before washing for the first time 34 Transportation 0004 34 Intended use For private domestic use only m he washing machine is suitable for washing machine washable fabrics and hand washable wool in water containing detergent m o be operated with cold mains water or cold and hot mains water max 60 C and standard detergents and care products which are suitable for use in washing machines m When measuring out the amount of all detergents additives care products and cleaning agents always follow the manufacturer s instructions m he washing machine may be used by children over the age of 8 years and by persons with reduced physical sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised or have been instructed by a responsible person Children must not carry out any cleaning or maintenance work without supervision m Keep children under the age of 3 years away from the washing machine m Keep pets away from the washing machine Read the Instruction Manual and Installation Instructions and all other information supplied with the washing machine and use the machine accordingly Retain the documents for subsequent use depe
15. themselves Do not leave children unattended near the washing machine Do not let children play with the washing machine en Safety instructions Z Warning Danger of death Children may lock themselves in appliances putting their lives at risk For appliances that have reached the end of their service life a Disconnect the mains plug a Cut through the mains cable and remove it along with plug m Destroy the lock on the washing machine door Z Warning Risk of suffocation Children may become wrapped in packaging film or packing parts if allowed to play with them or they may pull them over their heads and suffocate Keep packaging film and packaging parts out of the reach of children A Warning Risk of poisoning Detergents and care products may be poisonous if consumed Keep detergents and care oroducts out of the reach of children Z Warning Eye skin irritation Detergents and care products may cause Irritation if they come into contact with the eyes or Skin Keep detergents and care oroducts out of the reach of children Z Warning Risk of injury When you wash at high temperatures the glass in the a machine door gets ot Do not let children touch the hot washing machine door Environmental protection Packaging used appliance i Dispose of packaging in an environmentally responsible manner This appliance is labelled in accordance with European Dir
16. 871 m Connect both supply hoses to the cold water tap with a Y piece and m connect both supply hoses to the appliance Note Carefully turn on the taps and check that the connection points are not leaking The screw connection is under mains water pressure Water outlet Caution Water damage If the drain hose slips out of the wash basin or the connection point during draining due to high water pressure any escaping water may cause water damage Secure the drain hose so that it cannot Slip out Note Do not kink the water drain hose or put strain on it lengthways 32 You can lay the water drain hose as follows Outlet ina sink Warning Risk of scalding When you are washing at high temperatures there is a risk of scalding if you come into contact with hot detergent solution e g if hot detergent solution is being drained into a wash basin Do not reach into the hot detergent solution Caution Damage to the appliance fabrics If the end of the drain hose is immersed in the drained water water may be sucked back into the appliance and may damage the appliance fabrics Make sure that The plug does not block drainage from the sink The end of the drain hose is not immersed in the drained water The water drains away quickly enough Drainage into a siphon The connection point must be secured using a hose clamp with a diameter of 24 40 mm available from
17. ange the program Notes m Load laundry of the same colour No additional detergent is required the soaking solution is used for washing 12 Detergent Correct selection of detergent The care label is crucial for selecting the correct detergent temperature and treatment of the laundry gt See also www sartex ch If you visit www cleanright eu you will find further information on detergents care products and cleaning agents for domestic use Standard detergent with optical brighteners Suitable for boil washable white laundry made from linen or cotton Programme Cottons cold max 90 C Detergent for colours without bleach or optical brighteners Suitable for coloured laundry made from linen or cotton Programme Cottons cold max 60 C Detergent for colours delicates without optical brighteners Suitable for coloured laundry made from easy care fibres synthetic fibres Programme Easy Care cold max 60 C Detergent for delicates Suitable for delicate fine fabrics silk or viscose Programme Delicate Silk cold max 40 C Detergent for woollens Suitable for wool Wool programme cold max 40 C Saving energy and detergent For light and normal soiling you can save energy lower washing temperature and detergent Saving Soiling note Reduced temper Light ature and deter No visible dirt or stains Cloth gent quantity as ing has taken on some body per the recom
18. bol in the display is off m some phosphate free detergents contain water insoluble residue m select y Rinse or brush the laundry after washing m Ihe water level is too high It is not possible to add laundry Close the door immediately if necessary m Press the DO button to continue the program The door is unlocked It is possible to add laundry If you cannot rectify a fault yourself after switching the machine off and on again or a repair is required m switch off the appliance and pull out the mains plug m urn off the tap and call customer services 26 After sales service If you cannot rectify a fault yourself contact customer services gt Cover page We will always find an appropriate solution in order to avoid unnecessary visits by engineers Please give customer services the product number E no and the production number FD of the appliance E no Product number FD Production number You can find this information depending on the model On the inside of the door in the opened service flap and on the rear of the appliance Trust the expertise of the manufacturer Contact us for assistance By doing so you will ensure that the repairs are carried out by trained service personnel using genuine spare parts After sales service en Technical data Dimensions 60 x 55x 85 cm height x width x depth Weight 66 73 kg Mains connection Nominal voltage 220 240 V 50 Hz N
19. chine m When the washing machine is lifted by its protruding parts e g the washing machine door the components may break off and Cause injuries Do not lift the washing machine by protruding parts m Ifthe hose and mains cables are not routed properly there is a risk of tripping and injury Lay hoses and cables in such a way that there is no risk of tripping Caution Damage to the appliance Frozen hoses may rip burst Do not install the washing machine in areas exposed to frost or outdoors Caution Water damage The connection points for the water Supply hose and water drain hose are under high water pressure To prevent leaks and water damage you must follow the instructions in this section Notes m In addition to the safety information listed here the local water and electricity supplier may have special requirements m If in doubt have the appliance connected by a specialist Installation surface Note The washing machine be stable so that it does not move around The installation surface must be firm and level m soft floors floor coverings are not Suitable Installation on a base ora wooden joist floor Caution Damage to the appliance The washing machine may wander and tio topple from the base when spinning The feet of the appliance must be secured with holding brackets Order no WMZ 2200 WX 9756 CZ 110600 Z 7080X0 Note On wooden joist floors install the washing mach
20. e symbol also lights up in the display panel the washing machine has detected too much foam during the wash cycle and automatically activated additional rinse cycles to remove the foam Add less detergent to the next wash cycle with the same load If you want to lock the program to prevent it from being inadvertently adjusted you can select the childprooft lock as follows 17 en Operating the appliance Childlock 3 sec gt 3 O UT You can lock the washing machine to prevent the functions you have set from being changed inadvertently To do this activate the childproot lock when the program has started To activate deactivate press and hold theSpin speed and Finished in time buttons at the same time for approx three seconds he symbol appears in the display panel lights up The childproof lock is active flashes The childproof lock is active and the program selector has been adjusted To deactivate the childproof lock reset the program selector to the initial program The symbol lights up again Note To avoid the program to terminate do not turn the program selector beyond the Off position Note The childproof lock remains active after the program has ended and the appliance is switched off You must always deactivate the childproof lock If you want to start a new program Adding laundry Following the start of the program you can add or remove laundry as required Press
21. ective 2012 19 EU concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Tips on economical use Always fill the appliance with the maximum amount of laundry for each programme Overview of programmes Supplementary sheet for the operating and installation instructions Wash normally soiled laundry without a prewash save energy and detergent when washing lightly and normally soiled laundry Page 13 The selectable temperatures apply to the care labels on the textiles The temperatures in the machine may deviate from this so that you get the optimum mix of energy saving and washing results Environmental protection en Information about the energy consumption Page 10 The display provides information about the relative energy consumption in the selected programs The more indicator lights light up the higher the program s consumption This enables you to compare the consumption levels of the different programs when choosing your program settings and to decide on an energy and water saving program setting depending on the model Energy saving mode The display panel lighting goes out after a few minutes and the Dll button flashes Press any button to activate the lighting Energy saving mode is not activated if a programme
22. er pressure in the supply network At least 100 kPa 1 bar Maximum 1000 kPa 10 bar When the tap is open the water flow rate is at least 8 I min If the water pressure is higher than this a pressure reducing valve must be installed Cold water connection Note With a cold water connection only operate the washing machine using cold mains water Connect the water supply hose to the tap 26 4 mm 3 4 and to the appliance not necessary for Aqua Stop models as this is permanently installed Model Standard Positioning and connecting en Model Aqua Secure Note Turn on the tap carefully checking the leak tightness of the connection points The screw connection is under mains water oressure Hot and cold water connection Notes a With a hot water connection operate the washing machine with hot and cold mains water with a maximum temperature of 60 C Red hot water supply hose on the hot water tap and red valve on the appliance m White cold water supply hose on the cold water tap and white valve on the appliance Connection to the water pipes 34 26 4 mm HOT COLD i 31 en Positioning and connecting Connection to the appliance Connection of hot water appliances only to cold water If there is no hot water connection you need a Y piece available from customer service with single part number 050
23. es skin thoroughly if they come into contact with detergents or care oroducts lf swallowed accidentally seek medical advice Note Dilute viscous fabric softener and fabric conditioner with water to prevent blockages Pour the detergent and care products into the appropriate compartments Measuring aid for liquid detergent A Dispenser Il Detergent for the main wash water softener bleach stain remover Dispenser amp Softener starch do not exceed max Dispenser Detergent for prewash 1 Pull out the detergent drawer as far as possible 2 Add detergent and or care products 3 Close the detergent drawer Operating the appliance en Measuring aid for liquid detergent Position the measuring aid for dosing the correct amount of liquid detergent 1 Pull out the detergent drawer Press down the insert and fully remove the drawer 2 Slide the measuring aid forwards fold it down and click it into place 3 Reinsert the drawer Note Do not use the measuring aid for gel detergents and washing powder or for programs with prewash or when the Fertig in Ready in time is selected Start the programme Press the Dl button The indicator lamp lights up and the program starts The display panel shows the Ready in time while the program Is running or the program duration and the program progress symbols once the wash cycle has started Display panel Page 10 Note Foam detection lf th
24. haanGace see ws bowen 16 Start the programme 0 17 CAINDIOCCK sao ee cer oy aca wae eee 18 Adding laundry sonnan naana aaan 18 Changing the programme 18 Cancel the programme 18 Programme end during rinse hold 18 Programme end 00008 19 Removing laundry switching off the ADDIGNCE icc nens ed bo wawe Sk wer 19 5 Sensors cecceceeeee 19 Automatic load sensing 19 Unbalanced load detection system 19 VoltCheck 0 ee es 19 Ed Setting the signal 20 Cleaning and maintenance 20 Machine housing control panel 21 ROMS ne oa E ao edd ee a owed 21 WESCAINIG am aearcd gauche acres ee 21 Detergent drawer and housing 21 Detergent solution pump blocked 21 The drain hose at the siphon is DIOCKEO a ed aed Sa we ha 22 Filter in the water supply blocked 22 Faults and what to do about them aannnnnnnnnnunnnnnne 23 Emergency release 0 23 Information on the display panel 24 Faults and what to do about them 25 en Intended use After sales service 27 Technical data 27 Positioning and connecting 27 Included with the appliance Of Safety instructions 28 Installation surface 0 29 Installation on a base or a wooden OISUHOOF cee t8 00000 d2dnceand 29 Installation on a platform with drawer 29 Installing the appliance ina kitchenette eee 29 Removing
25. if necessary 25 en Faults and what to do about them Faults Cause Remedy Odours in the washing machine Depending on the model run the Drum Clean or 4 Cottons 90 C pro gram without laundry Add washing powder or a detergent containing bleach Note To prevent foaming only use half the amount of detergent recommended by the detergent manufacturer Do not use detergents designed for wool or del icates The nee symbol lights ud Have you used too much detergent in the display panel Foam Mix one tablespoon of fabric softener with 1 2 litre of water and pour it into may also be leaking from the detergent drawer Loud noises vibrations and machine move ment during the spin oele The display panel indica tor lights do not work compartment II not suitable for outdoor clothing sportswear or items stuffed with down Use less detergent in the next wash cycle m Isthe appliance aligned Align the appliance gt Page 33 m Are the appliance s feet fixed Secure the appliance s feet gt Page 33 m Have the transport braces been removed Remove the transport braces Page 29 m Has there been a power failure m Have the fuses blown Reset replace the fuses while the appliance is run m If the fault occurs repeatedly call customer services ning There is detergent resi due on the laundry The symbol lights up in the display in pause mode In the pause mode the sym
26. ine m In a corner if possible On a water resistant wooden board min 30 mm thick which is screwed tightly to the floor Installation on a platform with drawer Platform order no WMZ 20490 WZ 20490 WZ 20510 WZ 20520 Installing the appliance in a kitchenette Z Warning Danger of death There is a risk of electric shock if you touch live components Do not remove the appliance covering olate Notes m Recess width of 60 cm required Positioning and connecting en m Only install the washing machine underneath a continuous worktop that is securely connected to adjacent cabinets Removing the transport locks Caution Damage to the appliance m The machine is secured for transportation using transport locks If the transport locks are not removed the drum for example may become damaged when the machine is operated Before using the appliance for the first time make sure that you completely remove all four transport locks Keep the locks in a safe place m To prevent transport damage from occurring if the appliance is moved at a later date you must refit the transport locks before transporting the appliance Note Keep the screws and sleeves in a safe place 2 Unscrew and remove all four transport brace screws 29 en Positioning and connecting Remove the sleeves To do this remove the mains cable from the holders 3 Fit the covers Lock the covers firmly in place by ap
27. ing Turn off the tap Call cus tomer services gt Page 2 The childproof lock is activated deactivate it Too much foam has been detected and an additional wash cycle has been acti vated Add less detergent to the next wash cycle with the same load gt Page 17 Mains voltage is too low Undervoltage in the wash program The program duration is extended gt Page 19 Switch off the appliance wait for five seconds and then switch it on again If the dis play appears again call customer services gt Page 27 Faults and what to do about them en Faults and what to do about them Faults Water is leaking from the machine The machine is not filling with water Detergent is not being dis pensed The door cannot be opened The program will not Start The drum briefly jerks or judders after the program has started The water is not draining Water is not visible in the drum The spin result is not sat isfactory Laundry is wet too damp The spin cycle runs sev eral times The program is taking longer than usual The length of the program changes during the wash cycle Residual water in the care product compart ment amp Cause Remedy m Attach the drain hose correctly or replace tt m lighten the screw connection of the drain hose m Have you pressed the DO button m Isthe tap turned on Could the filter be clogged Clean the filter gt Page 22 Is the
28. is running lf the laundry is subsequently dried in a tumble dryer select the spin speed according to the tumble dryer manufacturer s instructions en Getting to know the appliance Getting to know the appliance Washing machine Detergent drawer gt Page 16 Operating display panel Door with door handle Open the door Close the door Service flap CG Co CO Control panel Control panel depending on the model Getting to Know the appliance en 3 105 14 16 Program selector for selecting a program and switching the machine on and oft via the Off position You can find an overview of all orograms on the supplementary sheet for the installation and operating instructions Change Temperature Page 13 Change Spin speed Page 13 Change Finished in time Page 14 Childlock 3 sec gt 3 deuT to prevent the set functions from being changed accidentally Page 18 To do so press Spin speed and Finished in time simultaneously for approx 3 seconds 6 Select additional program settings if necessary Page 14 m Speed Eco m Water amp Rinse m Easy lron m Prewash EZ Jue button for Starting a program m Interrupting a program e g to add items of laundry Page 18 Cancelling a program Page 18 Display panel for settings and information Page 10 dependi
29. n under the following conditions 1 If water damage is caused due to a fault in our Agua Stop system we will compensate domestic customers for the damage caused 2 The liability guarantee is valid for the service life of the appliance 3 It is a prerequisite of all warranty claims that the appliance with Aqua Stop must have been installed and connected correctly in accordance with our instructions this also includes a correctly fitted Aqua Stop extension genuine accessories Our warranty does not cover defective feed lines or fittings leading to the Aqua Stop connection at the tap 4 Appliances with Aqua Stop do not need to be supervised during operation nor secured afterwards by turning off the tap The tap only needs to be turned off if you are away from home for a long period e g for several weeks holiday TE Advice and repair order in the event of faults GB 0344 892 8979 Calls charged at local or mobile rate IE 01450 2655 0 03 per minute at peak Off peak 0 0088 per minute You can find the contact information for all countries in the attached after sales service directory Robert Bosch Hausgerate GmbH Carl Wery StraBe 34 81739 Munchen DEUTSCHLAND 9000979140 9408
30. nding on the model Safety instructions Electrical safety Z Warning Danger of death There is a risk of electric shock if you touch live components Never touch or hold the mains plug with wet hands a Only pull out the mains cable by the plug and never by the cable as this could damage it Risk of injury A Warning Risk of injury a When the washing machine is lifted by its protruding parts e g the washing machine door the components may break off and cause injuries Do not lift the washing machine by protruding parts a lf you climb on the washing machine the worktop may break and cause injuries Do not climb onto the washing machine a lf you lean on the washing machine door when it is open the washing machine may tip over and cause injuries Do not lean on the washing machine door when it is open Safety instructions en a Reaching into the drum when it is turning can cause injuries to hands Do not reach into the drum when it is turning Wait until the drum has stopped turning Z Warning Risk of scalding When you are washing at high temperatures there is a risk of scalding if you come into contact with hot water e g if hot water is being drained into a wash basin Do not reach into the hot detergent solution Safety for children Z Warning Danger of death If children play with the washing machine they may get into life threatening situations or injure
31. ng on the model Note The buttons are sensitive they only need to be touched gently en Getting to Know the appliance Display panel 90 30 amp amp O 60 20 111 40 US tk Note You will find settings and information for the selected program in the table xe 90 C Temperature in C cold 0 1400 Spin speed in rpm 0 no spin cycle draining only Page 13 Rinse Stop Page 13 Finished in time Program duration depends on the program selection in h min hours minutes End time preselection in hours End of program after hours Load recommendation Energy consumption display Page 7 The more indicator lights light up the higher the relative energy consumption e g 2 30 1 240 depending on the model depending on the selected program settings and model 10 More information on the display panel Program progress lt Washing wey spulen Rinse Schleudern Spin End Program end Program end during Rinse Stop Washing machine door The washing machine door cannot lights up be opened When the program has started The flashes washing machine door is not closed properly Tap 5 Tap not turned on no water pressure lights up amp Water pressure too low may flashes increase the program duration Childproof lock Page 18 C Childproof lock activated lights up oe Childproof lock activated program
32. odour g mended dosage m Light summer sports clothing worn for a few hours m shirts shirts blouses worn for up to one day m Guest bed linen and hand towels used for one day Normal Visible dirt or a few light stains g m shirts shirts blouses Sweat soaked worn a few times m Towels bedding used for up to one week Temperatureas Heavy per the care label Dirt and or stains clearly visi and detergent ble e g tea towels baby quantity as per items work clothing the recom mended dosage for heavy soiling Note When measuring the amount of all detergents additives care products and cleaning agents please always check the manufacturer s instructions and information gt Page 16 Programme default settings en Programme default settings The default program settings are displayed in the display panel after selecting the program You can change the default settings To do this repeatedly press the corresponding button until the required setting is displayed on the display panel Note Pressing and holding the buttons automatically runs through the setting values until the last one Then press the button again and you will be able to change the setting values again You can find an overview of all possible program settings on the supplementary sheet for the installation and operating instructions Temperature C Temp C Oeppoko C Button depending on the
33. ominal current 10 A 13 A Nominal power 2300 W Water pressure 100 1000 kPa 1 10 bar depending on the model Power consumption when switched off 0 12 W Power consumption when ready for use left on mode 0 43 W Positioning and connecting Included with the appliance Note Check the machine for transport damage Never use a damaged machine If you have any complaints contact the dealer from whom you ourchased the appliance or our customer services gt Page 27 27 en Positioning and connecting lt lt Mains cable Bag a Installation and operating instructions m Customer services location directory m Warranty m Cover caps for openings after the transport braces have been removed Water supply hose on AquaStop models Water drain hose Elbow for securing the water drain hose Cold water supply hose for models standard Aqua Secure for models with hot water connection additionally a hot water supply hose depending on the model In addition a hose clamp 24 40 mm diameter available from specialist dealers is required to connect the water drain hose to a siphon 28 Useful tools Spirit level for aligning m Spanner with WAF18 for loosening the transport braces and WAF17 for aligning the appliance feet Safety instructions Z Warning Risk of injury m he washing machine Is very heavy Be careful when lifting transporting the washing ma
34. on after being loaded into the washing machine Hand rinse these items of laundry thoroughly beforehand 16 Notes Mix items of laundry of varying sizes Laundry items of different sizes distribute themselves better during the spin cycle Individual laundry items may cause an unbalanced load m Observe the maximum specified load Overfilling adversely affects the washing result and promotes creasing 1 Unfold presorted laundry items and place them in the drum 2 Make sure that no items of laundry are trapped between the door and the rubber seal and close the door Measure and add detergent and care products Caution Damage to the appliance Cleaning agents and agents for pretreating laundry e g stain removers orewash sprays etc may cause damage if they come into contact with the surfaces of the washing machine Do not allow these agents to come into contact with the surfaces of the washing machine If necessary immediately wipe away spray residue and other residues droplets with a damp cloth Dosing Dose the detergents and care products according to m Water hardness ask your water Supply company m he manufacturer s instructions on the packaging he amount of laundry m soiling gt Page 13 Filling Z Warning Eye skin irritation Detergent and care products may spray out if the detergent drawer is opened while the machine is in operation Open the drawer carefully Rinse ey
35. plying pressure to the Snap in hooks Hose and cable lengths m Left hand connection Oo 5 gt oO z 30 m Right hand connection O gt lt Tip The following are available from specialist dealers the after sales Service m An extension for Aqua Stop or cold water supply hose approx 2 50 m order no WMZ2380 WZ10130 CZ11350 Z7070X0 A longer supply hose approx 2 20 m for standard model Water inlet Z Warning Danger of death There is a risk of electric shock if you touch live components Do not immerse the Aqua Stop safety valve in water it contains an electric valve Observe the following when connecting the machine Notes m With a cold water connection only operate the washing machine using cold mains water m With a hot water connection operate the washing machine with hot and cold mains water with a maximum temperature of 60 C Do not connect the machine to the mixer tap of an unpressurised hot water boiler Do not use a used supply hose Only use the supply hose supplied or one that was purchased from an authorised specialist retailer m Do not bend squash modify or cut through the water supply hose otherwise its strength is no longer guaranteed m Only tighten the screw fitting by hand If the screw connections are tightened too much with a tool pliers the thread may get damaged Optimum wat
36. r on the tap Disconnect the hose from the tap Clean the filter with a small brush A P D e gt 6 For standard and Aqua Secure models clean the filter on the rear of the appliance Faults and what to do about them en Remove the hose from the rear of Caution the appliance l Water damage Use pliers to remove the filter and Any escaping water may cause water then clean it damage Do not open the washing machine door if water can be seen through the glass 1 Switch off the appliance Disconnect the mains plug 2 Drain the detergent solution 3 Pull the emergency release downwards with a tool and release The washing machine door can then be opened E W 7 Connect the hose and check for leaks Faults and what to do about them Emergency release e g in the event of a power cut The programme will continue running when the power supply has been restored However if the laundry has to be removed the washing machine door can be opened as follows Z warning Risk of scalding When you are washing at high temperatures there is a risk of scalding if you come into contact with detergent solution and laundry If possible leave it to cool down Z Warning Risk of injury You may injure your hands if you reach into the drum while it is turning Do not reach into the drum when it is turning Wait until the drum has stopped turning 23 en Faul
37. rts The selected number of hours e g 8 h is shown in the display panel and counts down until the wash program starts The duration of the program is then displayed Note The length of the program is automatically adjusted when the program is running Certain factors can affect the program length e g m Program settings 14 m Detergent dosage additional rinse cycles if required due to foaming Load size type of textiles water absorption differs m Imbalances e g due to fitted sheets are offset with several start ups of spin cycles m Fluctuations in power supply Water pressure infeeding speed Following the start of the program you can change the preselected number of hours as follows 1 Press the Dll button 2 Use the Finished in time button to change the number of hours 3 Press the DII button Following the start of the program you can add or remove laundry as required Page 18 ad Additional programme settings You can find an overview of all possible additional settings on the supplementary sheet for the installation and operating instructions The settings vary depending on the model Speed Eco O Speed Eco Speed Eco Perfect Button with two possible settings for adapting the selected program Speed Washing in a shorter time while achieving a washing result that is consistent with but uses more energy than the selected program without the Speed
38. specialist dealers Outlet into a plastic pipe with rubber bushing or into a drainage pit Levelling Level the appliance using a spirit level Incorrect levelling may result in intense noise vibrations and wandering 1 Loosen the lock nuts using a wrench by turning it in a clockwise direction 2 Check the alignment of the washing machine with a spirit level and adjust it if necessary Change the height by turning the appliance feet All four appliance feet must stand firmly on the ground 3 Tighten the lock nut against the housing In doing so hold the foot tight and do not adjust its height The lock nuts on all four appliance feet must be screwed tightly against the housing Positioning and connecting en Electrical connection Warning Danger of death There is a risk of electric shock if you touch live components m Never touch or hold the mains plug with wet hands m Only pull out the mains cable by the plug and never by the cable as this could damage it m Never unplug the mains plug during operation Observe the following information and ensure that Notes m he mains voltage and voltage indicated on the washing machine rating plate are the same The connected load and fuse required are specified on the rating plate m he washing machine is only connected to an alternating current via a properly installed earthed socket m
39. sts are indicated by a box or a bullet point Contents Intended use 4 Safety instructions 5 Electrical safety nanana anaana 5 Risk of INnjUTY n on annaa aaa 5 Safety for children aaaaaa aaa 5 Environmental protection 7 Packaging used appliance T Tips on economical use T7 Getting to know the appliance 8 Washing machine 005 8 Control panel 2 0008 9 Display panel 0008 10 LAUNAY sarien nissenana 11 Prepare the laundry 11 Sorting laundry esaa aaaea ee oe 11 SAONO serer et he oe ek we eee 11 Dyeing bleaching 005 12 DOGMWING cdr see gates oe ete es 12 Detergent ssc ccetciwtwseiaes 12 Correct selection of detergent 12 Saving energy and detergent 13 Programme default settings 13 VEMDCIAlUles e26d a04ee00he84 13 GOM SPECO serrera oA eee ere aa 13 Finished in time 008 14 Additional programme settings 14 Speed ECO oonan anaa ee 14 Easy IrOn nuuanu 15 Water amp Rinse ee eee 15 Prewash c 0 ta8 2 6 064 we 8S ne ears 15 Sy Operating the appliance 15 Preparing the washing machine 15 Select programme switch on the appliance 2 dn ddd dee oe ee ale 15 en Change the programme default SeEttiNgS 2 cade ivie tebe tra See 16 Select additional programme seitings16 Placing laundry into the drum 16 Measure and add detergent and care DrOQUC S lt 4acc
40. the items of laundry with the appropriate program Stubborn or dried in stains can sometimes only be removed by washing several times Symbols on the care labels Note The numbers in the symbols indicate the maximum washing temperature that may be used KY Suitable for normal washing process e g Cottons program KE A gentle washing process is required e g Easy Care program KY An especially gentle washing process is required e g Delicate Silk program i Suitable for washing by hand e g Wool program 194 Do not machine wash Starching Note Laundry must not be treated with fabric softener Starching is possible in all wash programmes if liquid starch is used Measure starch into compartment amp in accordance with the manufacturer s instructions clean first if necessary 11 en Detergent Dyeing bleaching Dye should only be used in normal household quantities Salt may damage Stainless steel Always follow the dye manufacturer s instructions Do not use the washing machine to bleach clothes Soaking 1 Switch on the appliance 2 Select the 7 Cottons 20 C program 3 Pour soaking agent detergent into compartment Il in accordance with the manufacturer s instructions 4 Press the DII button 5 After approx 10 minutes press the Di button to pause the program 6 Leave the laundry to soak for as long as required then either press the Dl button again to continue the program or ch
41. ts and what to do about them Information on the display panel DEW Cause Remedy lights up flashes lights up E 93 EIG E23 C gt ON up the Ready in time flashes the Ready in time flashes Other displays 24 The temperature is too high Wait until the temperature drops The water level is too high It is not possible to add laundry Close the door immediately if necessary Press the DO button to continue the program Laundry may be caught Open and close the door again and press the DO but ton If necessary push the door closed or remove some laundry and then push it closed again If necessary switch the appliance off and on again set the program and make your individual settings start the program Turn on the cold water tap fully supply hose kinked trapped The water pressure is too low Clean the filter gt Page 22 Turn on the hot water tap fully supply hose for hot water kinked trapped Hot water pressure too low Clean the filter gt Page 22 supply hose for hot water not connected correctly Connect both supply hoses hot and cold water for hot water appliances gt Page 31 Note Ignore the message It is only displayed for the first wash cycle The drain pump is blocked Clean the drain pump gt Page 21 The drain hose drain pipe is blocked Clean the drain hose at the siphon gt Page 22 There is water in the base trough the appliance is leak
42. ve activated the childproof lock you must first deactivate it before you can set a program Use the program selector to select the required program Can be rotated in either direction The appliance is switched on The program default settings for the selected program appear in the display panel m Temperature Ihe maximum load and the duration of the program alternately m Energy consumption depending on the model 15 en Operating the appliance Change the programme default settings You can use the default settings for each wash cycle or change them To do this repeatedly press the corresponding button until the required setting is displayed The settings are activated without needing to be confirmed The settings are not saved after switching off the washing machine Default program settings Page 13 Select additional programme settings By selecting additional settings you can better adapt the washing process to your items of laundry The settings can be selected or deselected depending on the program progress The button indicator lamps light up if a setting is activated The settings are not saved after switching off the washing machine Additional program settings Page 14 Placing laundry into the drum Z Warning Danger of death ltems of laundry pretreated with cleaning agents that contain solvents e g stain remover cleaning solvent may cause an explosi
Download Pdf Manuals
Related Search