Amica PH6400Z hob
Contents
1. 0 O pmo O Limo O AN UI D ooo 1 n0 n t G EB OM 7 M PENE CU ik O H E be 5 1 OO Be 9 T Pe O CLEANING AND ROUTINE MAINTENANCE Daily cleaning and proper maintenance have crucial impact on the durability of your ceramic plate Clean the ceramic plate observing the same rules as for glass Never use abrasive or aggressive clean ing agents scrubbing powders or scratching sponges Cleaning the plate after every use e Wipe off slight not burnt patches of dirt using damp cloth without cleaning agent Washing liquid can cause blue discolora tion to appear on the plate The stubborn stains often cannot be removed after first cleaning even if special cleaning agents are used e Remove larger patches of dirt stron gly sticking to the plate using sharp scrapper and wipe off the surface with a damp cloth Cleaning scrapper 20 Removal of stains Light pearly stains aluminium residu es can be removed from cooled plate using special cleaning agents Calca reous residues i e boiled over water can be removed with vinegar or special cleaning agents Do not switch off the hotplate when remo ving sugar sugar containing food plastic or aluminium foil Immediately scrape off the residuals when still hot from the hotplate using a sharp scrapper When the dirt is removed you can switch off the plate and clean it again after cooling down using special cleaning2. lid or a fire blanket Warning Danger of fire do not store items on the cooking surfaces SAFETY INSTRUCTIONS Warning If the surface is cracked switch off the ap pliance to avoid the possibillity of electric shock The appliance is not intended to be operated by me ans of an external timer or separate remote control system You should not use steam cleaning devices to clean the appliance e Before using the ceramic plate for the first time read the Operating Manual carefully as thus you can ensure safe operation and avoid damage to the plate e lf the ceramic plate is operated near a radio TV set or other emitting device please check whether the touch panel works correctly e The ceramic plate should be installed by a qualified electrician e Do not install the plate near refrigerating devices e The furniture the plate is fitted in should be resistant to temperatures up to 100 C The requirement applies to the veneers edges plastic surfaces glues and varnishes e The plate can be used only after it has been fitted into furniture as only thus you will be protected from accidental contact with live components e Electric appliances can be repaired only by qualified specialists Unprofessional repairs may compromise the safety of the appliance e The appliance is disconnected from the mains only when the mains plug is pulled out from the socket or when the fuse has been switched off e Never allow children to remain un
3. not lighted although appliance has been discon dicator will work again after the hotplates are still hot nected from the mains switching the control panel on and off from the mains fuse and call the nearest Cus tomer Service Centre plate 8 Crack in the ceramic Danger Immediately disconnect the ceramic plate 9 If the fault still remains Disconnect the ceramic plate from the mains fuse and call the nearest Customer Service Centre Important You are the person responsible for proper condition and operation of the appliance in your household If you call the Service for a fault which resulted from improper opera tion you will be charged with the costs of the visit even during the period of warranty We shall not be held liable for damages caused by a failure to observe this Manual 23 TECHNICAL DATA Rated voltage 400V 2N 50 Hz Rated power PB 4VQ247CF hotplate 2 x 145 mm 1200 W hotplate 1 x 180 mm 1800 W hotplate 1 x 210 mm 2300 W Dimensions 5 6 x 518 x 50 Weight ca 7 8 kg WARRANTY Warranty Warranty services according to the warranty card The producer shall not be held liable for any damages caused by improper operation of the product Please enter the type and factory number of the plate from the rating plate IVO e NC E naar Factory Umberto EE 24 Amica O Service Help Line For the UK please call 0844 815 8880 For Ireland please call 0818 46 46 46
4. 3 OOO W dol On off sensor Cooking zone selector sensor Cooking zone indicators Lower heat setting selector Higher heat setting selector nne INSTALLATION Making the worktop recess e Worktop thickness should be 28 40 mm while its width at least 600 mm The worktop must be flat and level Edge of the worktop near the wall must be sealed to prevent ingress of water or other liquids e There should be sufficient spacing around the opening in particular at least 50 mm di stance to the wall and 60 mm distance to the front edge of worktop The distance between the edge of the opening and the side wall of the furniture should be at least 55 mm e Worktop must be made of materials including veneer and adhesives resistant to a tem perature of 100 C Otherwise veneer could come off or surface of the worktop become deformed e Edge of the opening should be sealed with suitable materials to prevent ingress of water e Worktop opening must cut to dimensions as shown on figure 1 e Ensure minimum clearance of 25 mm below the hob to allow proper air circulation and prevent overheating 560 mm for hob 600 mm 750 mm for hob 770 mm INSTALLATION Note When installing the hob in the kit chen worktop install a partition panel as shown on the picture If the hob is to be installed above a built in oven instal lation of the partition panel is not requ mmm mmm Ins
5. Amica PB 4VQ247CF o OPERATING MANUAL IOAA 646 10 2014 1 DEAR USER The plate is exceptionally easy to use and extremely efficient After reading the instruction manual operating the cooker will be easy Before being packaged and leaving the manufacturer the plate was thoroughly checked with regard to safety and functionality Before using the appliance please read the instruction manual carefully By following these instructions carefully you will be able to avoid any problems in using the appliance It is important to keep the instruction manual and store it in a safe place so that it can be consulted at any time It is necessary to follow the instructions in the manual carefully in order to avoid possible accidents Caution Operate the appliance only after reading understanding this Manual The appliance has been designed only for cooking Any other use for example for heating does not comply with its operating profile and may cause danger The producer reserves a right to implement changes having no impact on the opera tion of the appliance Certificate of compliance CE The Manufacturer hereby declares that this product complies with the general requirements pursuant to the following European Directives O The Low Voltage Directive 2006 95 EC Electromagnetic Compatibility Directive 2004 108 EC o FrP Directive 2009 125 EC and therefore the product has been marked with the C symbol
6. agents Special cleaning agents can be bought in supermarkets special electromechanical shops drugstores and shops with kitchen appliances Sharp scrappers can be bought in DIY shops shops with building tools and painting accessories CLEANING AND ROUTINE MAINTENANCE Never apply cleaning agent on a hot hotplate Leave the cleaning agent to dry and then wipe it off with a wet cloth Any residuals of cleaning agents should be wiped off with a damp cloth before heating the plate for the next time as otherwise they can have caustic effect Failure to observe the ceramic plate main tenance instructions can result in losing your warranty rights 2 Caution If from any reason you are not able to control the switched on plate switch off the main switch or screw out the fuse and call the Customer Service Caution Should cracks or splits appear on the surface of your ceramic plate immediately disconnect the plate from the mains by switching off the fuse or unplugging the plug and call the Customer Service EMERGENCY PROCEDURES Every time when emergency situation occurs you should switch off the working assemblies of the plate disconnect power supply call in the service as some minor faults can be removed by the user in accordance with the below specified instructions before calling the Customer Service please go through the Table checking every point PROBLEM CAUSE ACTION 1 The appliance is not wor pow
7. and the Declaration of Conformity has been issued to the manufacturer and is available to the competent authorities regulating the market TABLE OF CONTENTS Basic Eet 2 Safety LES HEIEREN 4 Description of the appliance eeeseeeee eene enne enne nnn nnn nnn 8 IN HE d e zeten P 9 OPSTAO ca 12 Cleaning and maintenance cocnccccnnnccconocecnnanonananennnnnronanarrnnnnnrrnnnnrrnannrrnananennanns 20 Emergency procedures coocccccccccnnocononconnnccnnnronanennnnrrnnnrrnnnrrnnnrrnnnrrrnnrrrnarrrmarernanos 22 Technical data EE 24 A o 24 SAFETY INSTRUCTIONS Warning The appliance and its accessible parts become hot during use Care should be taken to avoid touching heating elements Children less than 8 years of age shall be kept away unless continuously supervised This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Warning Unattended cooking on a hob with fat or oil can be dangerous and may result in fire NEVER try to extinguish a fire with water but switch off the appliance and then cover flame e g with a
8. attended near the cooktop nor to play with the control panel e When switched on the hotplates quickly become hot To avoid unnecessary power con sumption switch them on only after putting a cooking pot e Residual temperature indicator built in into the electronic system tells you whether the hotplate is still switched on and whether it is still hot e Should there be a power failure all the settings and indications will be cancelled Please be careful when the power supply is restored as hotplates which have been hot before power failure will no longer be controlled by the indicator e If there is a mains socket located near the hotplate please make sure that the supply cord does not touch the hot places e Do not leave the plate unattended when cooking on fats and oils as they create fire hazard SAFETY INSTRUCTIONS e Do not use plastic pots or containers made from aluminium foil as they melt in high temperatures and may damage the ceramic plate e Sugar citric acid salt etc both in liquid and solid state as well as plastic should not get into contact with a hot hotplate e lf through carelessness sugar or plastic gets on a hot hotplate you may not switch off the plate but scrape away sugar or plastic using a sharp scrapper Protect hands from burns e Use only flat bottom pots and saucepans on your ceramic plate without sharp edges or burrs as otherwise the plate may get permanently damaged e The heating surface of the cera
9. cessary peeping into pots e Not using the plate near refrigerators freezers As the consumption of energy unnecessary rises UNPACKING The appliance is protected from damage during transpor tation by its packaging After unpacking please dispose of the packing materials in a manner creating no risk to the environment All materials used for packing are harmless to the natural environment can be recycled in 100 and have been identified with ap propriate symbol Caution Packing materials polyethylene bags pieces of polystyrene etc should be kept away from children during unpacking DISPOSING OF THE DEVICE When disposing of the device do not bring it to regular munici pal waste containers Instead bring it to electrical and elec tronic waste recycling and reuse NA center A relevant label has been put on the device its instructions manual or on the package The device has been manufactured of recy clable materials By bringing old device to recycling collection center you show that you care about nature Ask your local environmental care authority for information on location of such facilities DESCRIPTION OF THE APPLIANCE Description of PB 4VQ247CF induction hob Back left cooking zone 145 Back right cooking zone 180 Front left cooking zone 210 Front right cooking zone Touch control sensor panel IN N N EN NM Y Ke NS O o O 0
10. ed certified installer Wilful adaptations or modifications to the electric system are prohibited Guidelines for the installer The plate is factory set for three phase alternating current power supply 400 V 2N 50 Hz It may be adapted for one phase current power supply 230 V by adequate bridging on the connection strip in accordance with the attached wiring diagram The wiring diagram is also provided in the bottom part of the lower cover The connection strip can be accessed once the lid on the bottom cover is removed Please remember to match the mains connection cable to the type of connection and the rated power of the plate Fix the mains connection cable in a stay wire Note Do not forget to connect the protective circuit to a clamp of the connection strip marked with 22 sign The plate power supply system should be protected by appropriately selected safety device or after the power supply protection by appropriate safety switch cutting off the power in case of emergency Before connecting the plate to the electric system read information provided on the rating plate and wiring diagram Note The installer is obliged to complete and leave with the user a certificate of connecting the plate to the mains attached to the warranty card Methods of connection other than those indicated on the diagram can damage the plate 12 INSTALLATION DIAGRAM OF POSSIBLE CONNECTIONS Important Heating elements voltage 230V Wa
11. er supply failure check the in house electric king system fuse replace if ne cessary 2 The appliance does not control panel has not been switch it on respond to the entered set switched on tings sensors have been touched touch the sensors for a bit for less than one second longer several sensors have been always touch only one sen touched at the same time sor except when switching off a hotplate 3 The appliance does not children lock has been switch off the children lock respond and emits a short activated signal 4 The appliance does not improper operation improper again activate the plate respond and emits a long sensors have been touched signal or proper sensors have been touched for too short time covered or dirty sensor uncover or clean the sen sensors sors 5 The whole appliance swit no settings have been en again switch on the control ches off tered within 10 seconds from panel and immediately enter switching the plate on the settings covered or dirty sensor uncover or clean the sen sensors sors 6 One heating zone swit limited time of operation again switch on the hot ches off and H is on the plate display covered or dirty sensor uncover or clean the sen sensors sors 22 EMERGENCY PROCEDURES PROBLEM CAUSE ACTION 7 Residual temperature indi power supply failure the the residual temperature in cator is
12. induction hob When the induction hob is switched off then all the cooking zones are disconnected and the indicators are off Touching the on off sensor field 1 switches on the induction hob and a flashing 0 ap pears on the right front sensor field 3 for 10 seconds Now the desired heating power can be set using the sensor field 5 and the sensor field 4 see setting the heating power If none of the sensor fields is switched within 10 seconds then the heating zone switches off Switching on the cooking zones If the induction hob is on i e at least one cooking zone is on then the next cooking zone can be switched on by touching sensor field 2 first to chose the appropriate cooking zone When a 0 flashes on the indicator the desired heating power can be set using the sensor field 5 and the sensor field 4 see setting the heating power If none of the sensor fields is touched within 10 seconds then the induction hob switches off 15 OPERATION Selecting a cooking zone Touching the cooking zone selection sensor field 2 activates the individual cooking zo nes A cooking zone is active when a number is flashing on indicator 3 We can then change the power level settings for a chosen cooking zone using the sensor field 5 or the 4 or switch off the cooking zone by touching simultaneously 5 and 4 After 10 seconds the cooking zone becomes inact
13. ing level 9 is displayed intermittently on the cooking zone indicator 3 with the letter A for around 10 seconds If you start to set the heating power level within 10 seconds by touching the sensor field 4 then the automatic warm up function is activated and the letter A remains lit for as long as it stays activated The cooking heating power level can be now changed at any moment using the method described above in the setting the heating power section If you do not start to set the heating power setting within 10 seconds then the letter A vanishes and the automatic warm up function is inactive If you do not wish the automatic warm up function to operate start selecting the heating power by touching the sensor 4 the letter A is not lit Switching off selected cooking zone Selected cooking zone may be switched off in the following way 1 Select the required cooking zone using the cooking zone selection sensor field 2 2 Then simultaneously press the sensor 5 and the sensor 4 or use the sensor 4 to lower the setting to D The letter H appears on the indicator sym bolising residual heat 17 OPERATION Residual temperature indicator When a hot plate has been switched off letter H is displayed indicating that the hotplate is still hot A When the indication goes out you can touch the hotplate bearing in mind that it still d
14. ive and to make further changes the cooking zone should be reactivated using the sensor field 2 Activation of the cooking zones always begins from the front right cooking zone and is changed clockwise by touching sensor field 2 Setting the heating power In order to set the heating power first select the desired cooking zone using the cooking zone selector sensor 2 Then when the cooking zone indicator 3 shows 0 and a digit is flashing start setting the required heating power using the sensor 5 or the sensor 4 If you do not wish the automatic warm up function to operate start the heating po wer selection by touching the sensor 4 first You can then gradually increase the heating power by operating the sensor field 5 or lower the heating power setting by operating the sensor 4 If however you do wish to cook using the automatic warm up function start heating power selection by touching the sensor 5 first see automatic warm up function 16 OPERATION Automatic warm up function Each cooking zone is equipped with an auto matic warm up function When this is activa ted then the given cooking zone is switched on at full power for a time dpending on the heat setting selected and is then switched back to the heat setting set Activate the automatic warm up function by setting the required heating power by touching the sensor 5 first Then the heat
15. mic plate is resistant to thermal shock It is neither hot nor cold sensitive e Avoid dropping objects on the plate A point hit for example a falling bottle with spices may in unfavourable circumstances lead to cracks and splits appearing on your ceramic plate e Boiled over residuals of food may penetrate damaged places and get to the live compo nents of the ceramic plate e Should cracks or splits appear on the surface of your ceramic plate immediately discon nect it from the mains In order to do so switch off the fuse or pull out the mains plug from the socket Call the Customer Service e Please observe the maintenance and cleaning guidelines Should you fail to proceed in compliance with the provided guidelines you will lose your warranty rights SAVING ENERGY Everybody who properly uses energy not only saves money but also consciously acts in aid of the natural environment So let s save electric energy by e Using proper cookware Pots and pans with flat and thick bottom help to save up to one third of electric energy Remember about the lid as otherwise the consumption of energy quadruples e Matching cookware to the size of the hotplate A cooking pot should neither be smaller nor bigger than the used hotplate e Maintaining hotplates and pot bottoms clean Dirt obstructs the transfer of heat heavily burnt food residuals often can be cleaned only with chemicals harmful to the environment e Avoiding ne
16. oes not have ambient temperature A Do not touch the hotplate and do not put heat sensitive objects on it when the H letter is displayed as you can burn yourself or melt the object During the supply voltage drop the H is no more shown In spite of this the hot fields can be still hot Important If the cooking plate is started again after the renewed switching on or after the supply voltage drop a short self test will be performed The H will be displayed on the residual heat indicator during about 45 to 60 minutes The indication of residual heat is not based on the measurement of a value but on the calculation depending on the operating time of hot fields Limited time of operation To increase reliability of the plate each hot plate is provided with operation time limiter The maximal time of operation depends on the last selected heating power level Ifthe heating power is not changed during the specified time see the Table the hotplate will be switched off automatically and the residual temperature indicator will be lighted If you want to continue cooking switch on the hotplate again at the required level of heating power 18 After the pause caused by the supply vol tage drop the highest possible temperatu re and the longest cooling time are taken into account and therefore the indication time is so long lasting This is of no importance for the further operation of the cooking
17. ouching the sensors for a long time will emit a fault signal Proper cookware There is specially made and tested cookware for cooking on ceramic plates availabl on the market Observe instructions provided by the cookware manufacturers Cookware with aluminium or copper bottoms can leave metallic discoloration very difficult to remove Be particularly careful when using enamelware as it may irreparably damage your plate when left on a hotplate with the content boiled down To achieve optimal power consumption optimal cooking times and to avoid burning of food boiled over on the plate observe the following recommendations Bottoms The cookware should have a stable flat bottom as sharp edged bottoms or bottoms with burrs and charred food residuals can scratch your ceramic plate and have abrasive impact on it Sizes The diameter of the bottom surface of the pot should match the diameter of the used heating element Lids Lids prevent heat from escaping from the pot and thus shorten the cooking time and reduce the consumption of power 14 OPERATION Touch control sensor panel When the cooking surface is connected to the electricity mains the symbol should light up briefly on the indicator 3 after which the induction hob can be switched on No objects should be placed on the sensor surfaces this could cause an error Touch sensor surfaces should be always kept clean Switching on the
18. plate Heating power Maximal time of level operation in hours OPERATION The child lock function O The child lock function protects the induction hob from being accidentally switched on by children pets etc When the mains power is off the child lock function is automatically deacti vated AN Start switching the locking function on off when the induction hob is off Switching on the child lock function Touching the on off sensor field 1 switches on the induction hob and a flashing 0 ap pears on the right front sensor field 3 for 10 seconds Then during these 10 seconds press sen sor fields 2 and 4 simultaneously After hearing the short beep press sensor field 5 and the letter L will be displayed on all the indicators 3 Switching off the child lock function Start this by pressing the main sensor field 1 the letter L will be displayed on all the indicators 3 Within 10 seconds of the on off sensor 1 being touched press sensor fields 2 and 4 simultaneously After hearing the short beep press sensor field 4 and the letter L will vanish from all the indicators 3 Switching off the appliance The induction hob operates when at least one cooking zone is on Pressing the on off sensor field 1 switches off the appliance and the letter H for residual heat appears on the cooking zone indicator 3 Lo O O 2 C ka mO 2 p O
19. rning In every type of connec tion protective grounding has to be connected to terminal GL Recom mended type of connector cable For 230 V power supply single phase connection with a neutral lead 1 2 terminals are shorted together neutral lead connected to 4 PE protective earth lead connected to 25 For 400 230 V power supply HO5VV F 2 phase connection with a neu or tral lead neutral lead connected HO5RR F to 4 PE protective earth lead 4X 2 5 mm connected to 25 L1 R L2 S L3 T N neutral lead terminal PE lead terminal Connect the remaining wire to clamp 3 connected to the cooker s internal system if the mains power supply is a 3 phase 400 230V current OPERATION Before first use e carefully clean the ceramic plate treating it as a glass surface e when used for the first time the plate can give off a bit of a smell so switch on the ventilation system or open the window e operate the plate observing the safety instructions 13 OPERATION The ceramic plate is equipped with sensors operated by touching the marked areas with a finger Every touch of a sensor is confirmed with a sound When switching the plate on and off and setting the heating power always touch only one sensor If you touch several sensors at the same time with the exception of switching off the hotplate or the clock the system will ignore the entered settings and should you keep t
20. talling hob in kitchen cabinet worktop min 25 If the hob was installed in the kitchen worktop above the drawer the bottom cover of the hob must be covered with a wooden panel or protective board for 25mm ceramic hobs SS 0 Installing hob in kitchen cabinet worktop above oven ANDO not install the hob above the oven without ventilation AN Route electrical lead so that it does not touch the lower guard 10 INSTALLATION Installation of PB 4VQ247CF plate e Use four A brackets for 38 mm thick worktops Fit the hob into worktop opening as shown on figure 2 and 3 To properly secure hob in 28 mm thick worktop use four 15x15x50 mm wooden blocks in addition to A brackets Fit the hob into worktop opening as shown on figure 4 and 5 e Check if adhesive seal is properly applied to the hob s flange e Loosely attach fixing brackets to the bottom of the hob Remove dust from the worktop insert hob into the opening and press in firmly Position fixing brackets perpendicularly to the hob s edge and tighten firmly 2 1 worktop 1 worktop 2 screw 2 screw 3 fixing bracket 3 fixing bracket 4 hob 4 hob 5 seal 5 seal 6 wooden block 11 INSTALLATION Connecting the plate to the electrical system Note The plate can be connected to the mains only by a qualifi
Download Pdf Manuals
Related Search