Franke TP-125B
Contents
1. FOOD WASTE DISPOSER FRANKE TURBO PLUS OWNERS GUIDE Important Read all instructions thoroughly IMPORTANT SAFETY INSTRUCTIONS Instructions pertaining to risk of fire electric shock or injury to persons Save these instructions WARNING When using electrical appliances basic precautions should always be followed including the following 1 Read all instructions before using the appliance 2 To reduce the risk of injury close Supervision is necessary when an appliance Is used near children 3 Do not put fingers or hands into a waste disposer while it is functioning 4 Turn the power switch to the off position before attempting to clear a jam or remove an object from the disposer 5 When attempting to loosen a jam in a waste disposer use a long wooden utensil e g spoon 6 When attempting to remove objects from a disposer use long handled tongs or pliers 7 To reduce the risk of injury please note this disposer is not for grinding hard materials such as glass and metal this disposer must be connected to the electric supply by means of either a power supply cord or insulated wires in a flexible conduit when installing the disposer care must be taken to ensure that the reset button of the overload protection device remains readily accessible BEAB Approved www franke co uk a 10 Additionally for continuous feed models Care must be taken to ensure that the supply is disconnect2. may have internal problems that require service or replacement IF TURNTABLE DOES NOT ROTATE FREELY Check for foreign object lodged between the turntable and grind ring Dislodge object by rotating table with a wooden utensil and remove object see 8B If no foreign object is present there may be internal problems CONNECTION OF AIR SWITCH TO UNIT To connect the air switch the tube should be connect to the nipple on the underside of the unit by pushing it on firmly Franke UK Limited West Park MIOC Styal Road Manchester M22 5WB Phone 44 0 161 436 6280 Fax 44 0 161 436 2180 Email info uk franke com www franke co uk Service amp Spares UK Mainland amp N Ireland Tel 0844 371 0195 Fax 0844 371 0198 franke servevastdirect co uk Republic of Ireland Tel 353 1 413 6481 Fax 353 1 413 6489 kalserve kal ie KITCHEN SYSTEMS LEAKS If the unit leaks at the top it may be due to 1 Improper seating of sink flange gasket choice putty or tightening 2 Support ring not tightened properly 3 Defective cushion mount If unit leaks at the waste elbow leak may be due to improper tightening of elbow flange screws A g wA AES lt EMOVE BUTTON SPLASH GUARD TURNTABLE SERIAL NO WARNING Before resetting disconnect the power supply please see SAFETY NOTE above The overload control prevents the motor from operating should overloading occur This safety feature protects y
3. ruggedly built to give you many years of trouble free service It will handle all normal food wastes but it will NOT grind or dispose of such items as plastic tin cans bottle caps glass china leather cloth rubber string clam and oyster shells aluminum foil or feathers 8 TROUBLESHOOTING Before seeking repair or replacement we recommend that you review the following SAFETY NOTE Before investigating you must disconnect the power supply Depending on the installation this can be done by either removing the plug from the socket or for continuous feed models switching the disposer control to OFF LOUD NOISES Other than those during grinding of bones and fruit pits These are usually caused by accidental entry of a spoon bottle cap or other foreign object To correct this remove splash guard and remove object with long handled tongs Replace splash guard UNIT DOES NOT START With splash guard removed check to see if turntable will rotate freely using a wooden utensil If turntable rotates freely replace splash guard and check reset button to see if it has been tripped Reset button is red and located opposite discharge elbow near the bottom see 8A Push button in until it clicks and remains depressed If reset button has not been tripped check for shorted or broken wire connecting to disposer Check electrical power switch fuse box or circuit breaker If wiring and electrical components are intact the unit
4. OW CUSHION MOUNT DETAIL GROOVE CUSHION BOTTOM OUNT BEAD 3 ELECTRICAL CONNECTIONS DANGER IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC SHOCK CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICEMAN IF YOU ARE IN DOUBT AS TO WHETHER THE APPLIANCE IS PROPERLY GROUNDED DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE IF IT WILL NOT FIT THE OUTLET HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN GROUNDING INSTRUCTIONS For waste disposers equipped with a grounded plug in power cord This appliance must be grounded In the event of a malfunction The plug must be plugged into an appropriate outlet that is properly or breakdown grounding provides a path of least resistance for installed and grounded in accordance with all local codes and electric current to reduce the risk of electric shock This appliance ordinances If the supply cord is damaged it must be replaced by is equipped with a cord having an equipment grounding conductor the manufacturer its service agent or similarly qualified person in and a grounding plug order to avoid a hazard 4 ATTACHING DISCHARGE ELBOW Assemble rubber gasket to waste elbow see 4A If you are connecting to a dishwasher return to section 1B If not make sure all plumbing connections are tight and in Connect waste elbow to the disposer see 4B proceed to step 5and accordance with all plumbing codes and ordinances then connect bottom of the elbo
5. ed by switching off the electric supply or by removing the plug from the socket outlet before freeing a jammed rotor When not operating the disposer leave the stopper in place to reduce the risk of objects falling into the disposer Do not operate disposer unless splash guard is in place For proper electrical earth instructions see the ELECTRICAL CONNECTION details of this manual All installations should be carried out by a qualified electrician The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable environmental collection point for the recycling of electrical and electronic equipment For more detailed information about recycling of this product please contact your local authority your household waste disposal service or the shop where you purchased the product Please retain for future reference 1 OVERFLOW APPLIANCE CONNECTIONS WHEN YOU DO NOT WISH TO UTILISE THE AIR SWITCH e g if hard wiring the WDU to a standard electrical switch For overflow or dishwasher connections complete the following procedure Alternatively go on to section 3 Using a blunt instrument steel punch or wooden dowel knock out entire plug see 1A Do not use a screwdriver or sharp instrument When knockout plug falls into Disposer you may remove it or grind it up when the disposer is used This will not damage the disp
6. embly see 2B GASKET MOUNTING SCREWS P MOUNTING CUSHION RING RING 2b INSTALLATION OF EZ MOUNT ASSEMBLY For TP 125B models Read completely before starting Raise the mount ring towards the top of the sink flange Remove cushion mount Remove mount ring You may want to practice installing the cushion mount at this point before you are under the sink See the IMPORTANT NOTICE Cushion Mount Detail below Unscrew support ring from the sink flange and remove fibre gasket You are now left with sink flange and rubber gasket The rubber gasket is used instead of plumbers putty with stainless steel sinks Others sinks will require silisone or plumbers putty If no caulking nis used insert sink flange through rubber gasket into sink opening Do not rotate sink flange once it is seated If you use silicone instead of the gasket form a ring around the underside of the sink flange see C Insert flange into sink opening press down hard to squeeze out excess see B From under the sink clean up excess flush with bottom edge of the sink opening From underneath sink slip fibre gasket onto exposed sink flange With arrows pointing up screw support ring onto the sink flange and hand tighten until the sink flange will not move At this point you may want to insert stopper in sink and fill water to check sink flange seal and ensure there are no leaks Place mount ring over sink flange and hold in place while installing cus
7. g off the switch usually controlled by a wall mounted switch Operation of disposer is now controlled in a typical manner by the wall mounted switch i E 253 TP 125B Batch Feed 330 2a INSTALLATION OF 3 BOLT MOUNTING ASSEMBLY For TP 50 TP 75 and TP 125 models Read completely before starting NB Pay close attention to the order of mount assembly parts as they have been correctly assembled by the factory 3 Bolt Mount System See A and B CS ae SINK FLANGE A Disassemble the mounting assembly as it has been shipped ___ by turning the sink flange until the projections align with the ACOD nk ranae caser notches in the mount ring and allow you to pull the sink flange up and out of the remaining mount assembly Note the PROTECTOR RING So sequence of these parts as they are stacked and refer to A 7 and B to identify each part Unpack the 3 mount screws and screw them half way through the mount ring notice THIS j SINK MOUNT RING SIDE UP is imprinted on top of the mount ring Next stack the rubber gasket on top of the protector ring and sit them on top of the pointed ends of the mount screws MOUNTING SCREWS 3 B Keep these assembled parts together and set aside Before you connect the disposer to the mount as
8. hion mount large side down so the groove on the inside of the cushion mount fits over the lip on sink flange see D The disposer must be installed so that the reset button in easily accessible IMPORTANT NOTICE Cushion Mount Detail When the cushion mount is installed correctly the lip of the sink flange fits into the groove of the inside of the cushion mount and the mount ring can be pulled downwards over the cushion mount and will be free to rotate The bottom bead of the cushion mount acts as a gasket between the bottom of the sink flange and the top of the disposer see F CONNECTION OF AIR SWITCH TO UNIT To install the button switch unscrew the tightening nut and thread plastic pipe and base of button switch through hole in sink work top Attach nut and tighten up nut on base of button switch Push in plastic pipe in to the nipple on the base of the unit TOP OF SINK FLANGE RUBBER GASKET FIBER GASKET OPEN AREA NO OBSTRUCTION MOUNT RING SHOULD BE FREE TO MOVE UP amp DOWN REMOVABLE SPLASH GUARD SINK FLANGE SINK FLANGE GASKET FIBER GASKET SUPPORT RING CUSHION MOUNT TOPPER B REMOVABLE SPLASH GUARD SINK FLANGE RUBBER SINK n GASKET OR CAULKING FIBER GASKET Se A SUPPORT RING Ce J NOTE ARROWS arf INDICATING UP MOUNT RING TIGHTENING EARS S ooon DISHWASHER INLET ELBOW GASKET SCREWS GROOVE FLANGE cho DISCHARGE ELB
9. oser in any way but may take some time to grind over the course of several uses Connect dishwasher hose see 1B using a hose clamp Make sure all plumbing connections are tight and in accordance with all plumbing codes and ordinances Run water and check for leaks Follow the following procedure With the disposer mounted on the sink and the unit connected to the mains turn ON the wall mounted switch Connect the air switch tube to the nipple on the underside of the unit If the disposer is OFF depress air switch actuator to turn the disposer ON FRANKE TURBO PLUS MODELS 356 Continuous Feed Continuous Feed I RRRS 1S ee P o mm ae ae TP 50 TP 75 295 416 KNOCK 1A 4 OUT PLUG WOOD OR METAL DOWEL 253 E E TP 125 Continuous Feed 330 DISPOSER 491 xAIRGAP 1B RUBBER HOSE DISHWASHER HOSE DRAIN Air gap may not be required for all installations Check local plumbing codes With the disposer ON pull air switch hose from disposer connection and discard air switch actuator and hose Turn the disposer OFF by turnin
10. our house wiring and your disposer When overloaded the motor will stop automatically Splash guard is not used with Batch Feed or 3 Bolt Mount units
11. p waste and fats solid so disposer can rinds and cobs Large bones and fibrous husks require flush away particles 6B BATCH FEED OPERATING INSTRUCTIONS The Anti Jam Swivel Impellers make a clicking sound as the neck of the disposer Push down firmly to turn the disposer they swing into place This indicates normal operation on Lift stopper to shut the disposer off D Run disposer for 15 seconds after shredding stops This h l is th hly flush h h th in A Remove sink stopper and turn on a medium flow of cold water ensures that all waste is thoroughly flushed through the drain E To fill sink insert stopper and align the largest slot with the switch plunger see C Push down to seal sink without starting the disposer When medium sized slot see B in stopper base Is lined up with the switch plunger water can C Insert stopper to start disposer see B One of the two small drain but tableware etc cannot be accidentally dropped slots in stopper base must line up with switch plunger inside into disposer B Scrape in food waste Down the drain go table scraps vegetable peelings cobs rinds pits bones and coffee grounds see A MEDIUM A SLOT a 7 TIPS FOR SUCCESSFUL OPERATION A Be sure disposer is empty before using your dishwasher so it may drain properly B You may want to leave the stopper in the drain when not in use to prevent utensils and foreign objects from falling into the disposer C Your disposer is
12. sembly under the sink you may want to practice engaging the groove of the cushion ring to the ridge at the bottom of the sink flange see A and read Sec 5 C Be sure your sink is clean Pack the underside rim of the sink flange with plumber s putty see C Position the sink flange so it is centered and readable as you look into your sink Push the sink flange firmly into the sink opening to make a good seal RUBBER SINK FLANGE GASKET DO NOT move or rotate the sink flange once seated or the seal may be broken ED PROTECTOR RING MOUNTING D Take the remaining portion of the mount assembly as it was SCREWS gt N set aside and make sure that the rubber gasket is on top of the m protector gram under the sink while holding the sink a CUSHION RING flange firmly with one hand line up the notches in the mount ring with the projections of the sink flange Slide the mount RIDGE assembly up onto the sink flange past the projections and DISHWASHER ae T eee INLET give the mount assembly a 1 4 turn so that it will hang by HOPPER itself see D a i ga SCREWS MOUNT RING ELBOW E Tighten the 3 mounting screws evenly with a screwdriver FLANGE see E DO NOT OVERTIGHTEN Trim off excess putty ELBOW N DISCHARGE ELECTRICAL GASKET ELBOW CONNECTIONS Mount Assembly SERIAL RECORD ON WARRANTY CARD PROTECTOR Batch Feed Stopper looks different than the stopper illustrated RUBBER Mount Ass
13. t ring to the right counter clockwise until it locks up tight Tap the mount ring ears with a hammer until the lock LOCKING DETAIL position is achieved Hopper projections must be to extreme a HOPPER PROJECTION IN left of mounting slots see 6C amp 6D a Serko ee 1 Onan D If mount ring is hard to turn you may add a small amount of petroleum jelly or liquid soap to hopper projections Run water HOPPER PROJECTION IN MOUNT and check for leaks LOCK POSITION RIN 6A CONTINUOUS FEED OPERATING INSTRUCTIONS The Anti Jam Swivel Impellers make a clicking sound as considerable grinding time and are more easily thrown away they swing into place This indicates normal operation with other trash Do not be alarmed that the disposer slows down while grinding The disposer is actually increasing torque A Remove sink stopper Turn on a medium flow of cold water grinding power and is operating under normal conditions B Turn switch to ON position your motor is turning at full speed D Before turning disposer off let water and disposer run for and ready to use approximately 15 seconds after shredding stops This ensures C Scrape in food waste Down the drain go table scraps that all waste is thoroughly flushed through trap and drain peelings rinds seeds pits small bones and coffee grounds E Itis not recommended to use hot water while running disposer To speed up food waste disposal cut or break up large bones Cold water will kee
14. w by tightening the slip nut see 4C Run water and check for leaks RUBBER Jf SORE fo AA 4B 5A 5a 3 BOLT MOUNT ASSEMBLY For TP 50 TP 75 and TP 125 models IMPORTANT PLEASE READ DO NOT REMOVE CLAMP FROM CUSHION RING OR CUSHION RING FROM HOPPER BOTH PARTS ARE FACTORY INSTALLED AND INSTALLATION READY A Press firmly around the cushion ring to ensure it is engaged of the cushion ring around the RIDGE at the bottom of the with the neck of the disposer sink flange see 5A amp refer back to 2B While still supporting the disposer tighten the screw clamp around cushion ring B Lubricate the top inside lip of the rubb hion ri ith ubricate the top inside lip of the rubber cushion ring with a ihe aieooserwilnownanebyacelk liquid soap If you need to turn the disposer make sure the sink flange does C Line up discharge elbow of disposer with trap under mountin P 8 p p 8 not turn It will break the seal created when installed assembly see 5A Guide disposer up and engage the GROOVE 5B SINK FLANGE SINK FLANGE CUSHION RING TOP ANGLED SURFACE SINK FLANGE CUSHION _ RING p a HOPPER 5b EZ MOUNT ASSEMBLY For TP 125B models A Line up disposer under mounting assembly Guide hopper projections into mount ring slots Turn mount ring about 1 4 to right so that disposer is temporarily supported see 6A B Turn mount ring and disposer until disposer elbow lines up with trap see 6B C Turn moun
Download Pdf Manuals
Related Search