Powerplus POWXQG7556 lawnmower
Contents
1. KS ositicn to position 3 When operating turn throttle choke lever to S position Fig 10A Fig 10B 4 Standing behind the unit grasp the brake control handle and hold it against the upper handle as shown in fig 10C 5 Grasp the starter handle as shown Fig 10C and pull up rapidly Return it slowly to the rope guide bolt after engine starts 6 Release the brake control handle to stop the engine and blade Start the engine carefully according to instructions and with feet well away from the blade Copyright 2015 VARO Page 9 www varo com POWERPLUS POWXQG7556 EN Do not tilt the lawn mower when starting the engine Start the mower on a level surface free of high grass or obstacles Keep hands and feet away from the rotating parts Do not start the engine when standing in front of the discharge opening gt gt 8 3 Brake handle During operation tightly hold the brake handle with both hands Note During operation when the brake handle is released the engine will stop and thus stopping the lawnmower from operating Warning In order to avoid any unintentional start ups of the lawn mower it comes equipped with an engine brake which must be pulled back before the engine can be started When the engine control lever is released it must return to its initial position at which point the engine automatically switches off Note Engine brake brake handle Use the lever to stop the engine When you2. Replace all fuel tank and container caps securely Replace faulty silencers Before using always visually inspect to see that the blades blade bolts and cutter assembly are not worn or damaged Replace worn or damaged blades and bolts in sets to preserve balance 5 3 Operation Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect Warning Do not use the lawnmower when there is a risk for lighting It is recommended to limit the duration of operation in order to minimize the risks from noise and vibration Be careful when using the lawnmower in slopes and near drop offs ditches or embankments Mow only in daylight or in good artificial light Avoid operating the equipment in wet grass where feasible Always be sure of your footing on slopes Copyright 2015 VARO Page 5 www varo com POWERPLUS gt _ POWXQG7556 EN Walk never run For wheeled rotary machines mow across the face of slopes never up and down Exercise extreme caution when changing direction on slopes Do not mow excessively steep slopes Use extreme caution when reversing or pulling the lawn mower towards you Stop the blade s if the lawn mower has to be tilted for transportation when crossing surfaces other than grass and when transporting the lawn mower to and from the area to be mowed Never operate the lawn mower with defective guards or without safety devices for example deflect
3. Tool box 7 Grass catch bag 17 Brake control handle 8 Height adjusting lever 18 Speed adjusting lever 9 Deck 19 Mulching wedge 10 Sideward flap 20 Discharge channel 3 PACKAGE CONTENT LIST Remove all packaging materials Remove remaining packing and package inserts if included Check that the package contents are complete Check the appliance the power cord the power plug and all accessories for transportation damage Keep the packing materials as far as possible till the end of the warranty period Dispose it into your local waste disposal system afterwards WARNING Packaging materials are not toys Children must not play with plastic bags Danger of suffocation 1 x self propelled lawn mower 190 cc 1 x grass bag 1 x spark plug wrench 1x manual ah If any parts are missing or damaged please contact your dealer Copyright 2015 VARO Page 3 www varo com FowERrLus ATI 4 SYMBOLS In this manual and or on the machine the following symbols are used POWXQG7556 EN Denotes risk of personal injury or damage to the tool Read manual before use Danger rotating blades Keep hands and feet away from sharp parts Keep hands away from blades Don t touch the blades when starting or while operating the unit Toxic fumes Don t operate inside house Petrol engines emit carbon monoxide DO NOT run in enclosed area When repairing please take out the spark plug Then repair ac
4. fitted remove the key Whenever you leave the lawn mower Before refuelling Reduce the throttle setting during engine shut down and if the engine is provided with a shut off valve turn the fuel of at the conclusion of mowing Go slow when using a trailing seat Maintenance and storage Keep all nuts bolts and screws tight to be sure the equipment is in safe working condition never store the equipment with petrol in the tank inside a building where fumes can reach an open flame or spark Allow the engine to cool before storing in any enclosure To reduce the fire hazard keep the engine silencer battery compartment and petrol storage area free of grass leaves or excessive grease Check the grass catcher frequently for wear or deterioration Replace worn or damaged parts for safety If the fuel tank has to be drained this should be done outdoors Improper maintenance use of non conforming replacement components or the removal or modification of safety components can damage the lawnmower and injure the operators seriously Copyright 2015 VARO Page 6 www varo com POWERPLUS gt _ POWXQG7556 EN Only use the recommended blades and spare parts by the manufacturer The use of non genuine parts can damage the machine and injure the operators Keep the lawnmower in good working condition If the blade stopping device doesn t work please contact service centre for help A Warning Do not touch rotating blade
5. varo com EQWREEPLUS XQ POWXQG7556 EN HIGH QUALIT Eege 11 Height adjustment iNStrUCTIONS cccccceeeseeccceeeennnnnceseeeennnaneneseeeenannsesseeeennaesesseeeenaans 11 CLEANING AND MAINTENANCE ccccccsseesseeeseeessseesseeenseees 12 SPAIK DIG risegen on ii RE A E NE R N 12 Lubrication INSIFUCTIONS ssssssioiirso ieissar iania araa aaa ce aos Sasa a 12 STORAGE INSTRUCTIONS OFF SEASON cessetseeseeeeeeeeees 13 TRANSPORT eege 13 TROUBLES SHOOTING sissi 14 Zeile vi 15 NOISE soono cee cca case eee cca ac See aaa 15 WARRAN Viss e ieee 16 EN VIRONMENT zosi see scnecesceoetucteceamenssanspsabacnestusnensenauaceeet 16 DECLARATION OF CONFORMITY sseeeeeeeeeeeeeeeeeeeeeeennees 17 Copyright 2015 VARO Page 2 www varo com PoweRPLus X X POWXQG7556 EN SELF PROPELLED LAWN MOWER 190CC 560MM POWXQG7556 1 APPLICATION The purpose of this lawn mower is to cut grass This lawn mower has been designed for cutting grass areas in a domestic garden It is not designed for commercial use before using the appliance for your own safety Your power tool should WARNING Read this manual and general safety instructions carefully only be passed on together with these instructions 2 DESCRIPTION FIG A 1 Upper handle 11 Spark Plug 2 Get drive control handle 12 Fuel cap 3 Choke Lever 13 Oil Cap 4 Starter handle 14 Locking knob 5 Rope Guide 15 Cable clamp 6 Locking Lever 16
6. 2 4 Edge cutting Lawn mower is designed so that the diameter of the deck lies outside the line of wheels In this way you can cut the edges very easily 8 OPERATING INSTRUCTIONS 8 1 Before starting Service the engine with gasoline and oil AN WARNING Petrol is highly flammable Store fuel in containers specifically designed for this purpose Refuel only outdoors before starting the engine and do not smoke while refuelling or handling fuel Never remove the cap of the fuel tank or add petrol while the engine is running or when the engine is hot If petrol is spilled do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until petrol vapours have dissipated Replace all fuel tanks and container caps securely Before tipping the lawn mower to carry out any work on the blade or drain oil remove fuel from tank WARNING never fill fuel tank indoors with engine running or until the engine has been allowed to cool for at least 15 minutes after running 8 2 To start engine and engage blade Before start adjust the speed adjusting lever at 1 position 1 The unit is equipped with a rubber boot over the end of the spark plug Make certain the metal loop on the end of the spark plug wire inside the rubber boot is fastened securely over the metal tip on the spark plug 2 When starting cool or warm engine turn throttle choke lever at anywhere between
7. POWERPLUS gt _ POWXQG7556 EN NO N NO oo N Nh iN APPEICA PION WE 3 DESCRIPTION FIG A E 3 PACKAGE CONTENT LIST ccsssssseeecsssssseeeeecessseeeeeeensseseeseeass 3 OS riers ees te seer ve ese vaste see encseceniecoe sus aveeeteeesnenuesscaudeeest 4 GENERAL SAFETY WARNINGG cccccessssssseeeeceenseeesseeenseeesees 5 DI e aatrae P cece A AEA A A A 5 PRED AN ATION seta zcestectietesdesestin testis i i R EERE 5 DA E 5 Maintenance and storage c1sscccnnscccenncncnnnenennnenenanesennnesenanesenanesenaneseonnesenenesenanesenaness 6 ASSEMBLY E 7 FOUN Handle ossessioni eet eee ieee 7 Adjustment for an appropriate angle Fig 21 7 Mounting and dismounting the grass Catcher eeEeESSSSSSSRRSSEEEEEEEEEEEEREEEEEEEEEEEEEEEE 7 Sigel EE ee 7 HOITO E 7 TOOL ON ee 7 AN EE 8 What 1S MUICDING KE 8 Rtg USCS iissteseustediusese ad suedat sd acieivad around E A NEEE GERAS 8 Retrofitting for mulching MOWEL sssssesrsenesnsrnenrrrneenrrreerrrrerirrteerrttterrtrrerrrrreerrrrrerrrerent 8 Resetting for side discharge movwing 8 Betor Starting SE 9 To start engine and engage DAAC scccccccennseececeeeennnnsecsseeeenaeneseseeeeneneessseeenensnnees 9 Brake handie ee 10 TO SIOD ONING osise EA EDE E EEEE 10 PLUTO MOVE ocenie enS EEE E RERE 10 For the best results when MOWING scccccccennnencccseeennnnessseeennannseseseennaenesseeeenaans 11 Grass E 11 Copyright 2015 VARO Page 1 www
8. Warning Refuel in a well ventilated area with the engine stopped 6 ASSEMBLY 1 Folding handle Use the knob to fix the lower handlebars into the unit body Fig 1A 6 1 2 Lift the two locking levers to release the upper handlebars for folding 3 Push the locking lever closed to lock the handlebars in the operating position Fig 1B 4 Adjust the tension by turning the lock nut with a suitable spanner 5 Attach the cable clamp to the position shown and then attach the cable Fig 1C Fig 1D Caution Traction and starter cables must always be positioned on top of the cross bar of the push handle This provides free movement of the cables on top of the lower section of the push handle when the handle is folded Incorrect mounting of these cables could lead to damaging and or straining them resulting in a malfunction of the machine In this case the guaranty is void 6 2 Adjustment for an appropriate angle Fig 2 Pull the locking lever opening By rotating the upper handle which acts on the adjustment mechanism for angle adjustment a suitable angle can be adjusted in the range of 20 to 20 5 position 20 10 0 10 20 as the Fig 2 shown Push the locking lever closed to connect the lower handle and the upper handle N 6 3 Mounting and dismounting the grass catcher 1 To fit Raise the rear cover and hitch the grass catcher on rear of mower Fig 3A Fig 3B To remove grasp and lift rear cov
9. and other relevant provisions of the applicable European Directives based on the application of European harmonized standards Any unauthorized modification of the apparatus voids this declaration European Directives including if applicable their amendments up to the date of signature 2006 42 EC 2004 108 EC 2000 14 EC Annex VI LwA 93dB A 98dB A Testing Authority TuV Sud Munich European harmonized standards including if applicable their amendments up to the date of signature EN ISO 5395 1 2013 EN ISO 5395 2 2013 EN ISO 14982 2009 Keeper of the Technical Documentation Philippe Vankerkhove VARO Vic Van Rompuy N V The undersigned acts on behalf of the company CEO r d Philippe Vankerkhove Regulatory Affairs Compliance Manager 25 09 14 Copyright 2015 VARO Page 17 www varo com
10. cording to the operation manual Mandatory use of eye protection Wear gloves KEEP HANDS and FEET AWAY Wi In accordance with essential applicable safety standards of European directives Warning Flying objects Beware of thrown objects hit by cutting attachment Keep bystanders away Fuel is flammable keep fire away Allow engine to cool for at least 2 minutes before refuelling Wear hearing protection amp eye protection Caution Hot engine Do not touch a hot silencer or cylinder You may get burned These parts get extremely hot from operation When turned off they remain hot for a short time Wear noise protection Keep hands and feet away Warning Keep the safety signs clear and visible on the equipment Replace the safety signs if they are missing or illegible Copyright 2015 VARO Page 4 www varo com PoweRPLus AL POWXQG7556 EN 5 GENERAL SAFETY WARNINGS WARNING When using petrol tools basic safety precautions including the following should always be followed to reduce the risk of serious personal injury and or damage to the unit Read all these instruction before operating this product and retain these instructions for future reference WARNING This machine produces an electromagnetic field during operation This field may under some circumstances interfere with active or passive medical implants To reduce the risk of serious or fatal injury we recommend persons with medical implan
11. er remove grass catcher 6 4 Starter handle 1 Move the starter handle from the engine to the rope guide Fig 4A 6 5 Height of cut 1 Apply outward pressure to disengage lever from rack Move lever forward or back to adjust height Fig 5 and see clause 7 9 6 6 Toolbox 1 To fit press the tool box into the handle panel Lock the tool box with the handle panel the nose on the bottom side of the tool box must snap into the handle panel Fig 6A Fig 6B 3 This type of lawn mower have two tool box one is built in box the other is external box for the built in box you can push the button to open it and then press the cover to lock it You can put tools such as spanner screwdriver and also put drinking bottles in these boxes Fig 6C Copyright 2015 VARO Page 7 www varo com POWERPLUS gt _ POWXQG7556 EN 7 4IN1 These lawn mowers can be retrofitted from its normal function based on the application purpose From lawn mower with rear discharge to Mulching mower or as side discharge mower 7 1 What is mulching When mulching the grass is cut in one working step then finely chopped and returned to the grass strip as natural fertilizer Hints for mulch mowing Regular cut back by max 2 cm from 6 cm to 4 cm grass height Use a sharp cutting knife Do not mow wet grass Set to max motor speed Only move at working pace Regularly clean mulching wedge housing inner side and mowing blade 7 2 Differen
12. lter MRAN AN NOTE Replace filter if frayed torn damaged or unable to be cleaned 9 3 2 Cutting blade CAUTION Be sure to disconnect and ground the spark plug wire before the hex bolt and washer which hold the blade and blade adapter to the engine crankshaft Remove the blade and adapter from the crankshaft working on the cutting blade to prevent accidental engine starting Protect hands by using heavy gloves or a rag to grasp the cutting blades Remove WARNING Periodically inspect the blade adapter for cracks especially if you strike a foreign object Replace when necessary For best results your blade should be sharp The blade may be resharpened by removing it and either grinding or filing the cutting edge keeping as close to the original bevel as possible It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade Improper blade balance will result in excessive vibration causing eventual damage to the engine and mower Copyright 2015 VARO Page 12 www varo com POWERPLUS SZ POWXQG7556 EN Be sure to carefully balance blade after sharpening The blade can be tested for balance by balancing it on a round shaft screwdriver Remove metal from the heavy side until it balances evenly Before reassembling the blade and the blade adapter to the unit lubricate the engine crankshaft and the inner surface of the blade adapter with light oil Install the blade adapter on the c
13. lug Clean and grease the lawnmower carefully as described above under Lubrication Slightly grease the cutter to avoid corrosion Store the lawnmower in a dry clean and frost protected place out of reach of unauthorized persons ey Caution The engine must have completely cooled down before storing the lawnmower NOTE When storing any type of power equipment in an unventilated or material storage shed care should be taken to rust proof the equipment Using a light oil or silicone coat the equipment especially cables and all moving parts Be careful not to bend or kink cables If the starter rope becomes disconnected from rope guide on handle disconnect and ground the spark plug wire Depress the blade control handle and pull the starter rope out from engine slowly Slip the starter rope into the rope guide bolt on handle 11 TRANSPORT Turn the engine off Ensure not to bend or damage the cutter when pushing the lawnmower over obstacles Copyright 2015 VARO Page 13 www varo com FowERrLus SI POWXQG7556 EN 12 TROUBLES SHOOTING PROBLEM Engine does not start Engine difficult to start or loses power Engine operates erratically Engine idles poorly Engine skips at high speed Engine overheats Mower vibrates abnormally Copyright 2015 VARO PROBABLE CAUSE Throttle chock not in the correct position for the prevailing conditions Fuel tank is empty Air clea
14. n mowing Clear lawn of debris Be sure that the lawn is clear of stones sticks wire or other foreign objects which could be accidentally thrown out by the mower in any direction and cause serious personal injury to the operator and others as well as damage to property and surrounding objects Do not cut wet grass For effective mowing do not cut wet grass because it tends to stick to the underside of the deck preventing proper mowing of the grass clippings Cut no more than 1 3 the length of the grass The recommended cut for mowing is 1 3 the length of the grass Ground speed will need to be adjusted so the clippings can be dispersed evenly into the lawn For especially heavy cutting in thick grass it may be necessary to use one of the slowest speeds in order to get a clean well mowed cut When mowing long grass you may have to cut the lawn in two passes lowering the blade another 1 3 of the length for the second cut and perhaps cutting in a different pattern than was used the first time Overlapping the cut a little on each pass will also help to clean up any stray clippings left on the lawn The mower should always be operated at full throttle to get the best cut and allow it to do the most effective job of mowing Clean underside of deck Be certain to clean the underside of the cutting deck after each use to avoid a build up of grass which would prevent proper mulching Mowing leaves The mowing of leaves can also be beneficial to your lawn When mo
15. ner element is dirty Spark plug loose Spark plug wire loose or disconnected from plug Spark plug gap is incorrect Spark plug is defective Carburettor is flooded with fuel Faulty ignition module Dirt water or stale fuel tank Vent hole in fuel tank cap is plugged Air cleaner element is dirty Spark plug is defective Spark plug gap is incorrect Air cleaner element is dirty Air cleaner element is dirty Air slots in engine shroud are blocked Cooling fins and air passages under engine blower housing are blocked Gap between electrodes of spark plug is too close Cooling air flow is restricted Incorrect spark plug Cutting assembly is loose Cutting assembly is unbalanced Page 14 CORRECTIVE ACTION Move throttle chock to correct position Fill tank with fuel Clean air cleaner element Tighten spark plug to 25 30 Nm Install spark plug wire on spark plug Set gap between electrodes at 0 7 to 0 8 mm Install new correctly gapped plug Remove air cleaner element and pull starter rope continuously until carburettor clears itself and install air cleaner element Contact the service agent Drain fuel and clean tank Fill tank with clean fresh fuel Clean or replace fuel tank cap Clean air cleaner element Install new correctly gapped plug Set gap between electrodes at 0 7 to 0 8 mm Clean air cleaner element Clean air cleaner element Remove debris from shots Remove debris fr
16. om cooling fins and air passages Set gap between electrodes at 0 7 to 0 8 mm Remover any debris from slots in shroud blower housing air passages Install RJ19LM spark plug and cooling fins on engine Tighten blade Balance blade www varo com POWXQG 7556 EN Model nr POWXQG7556 Cylinder capacity 190 cc Engine power 4 2 kW Engine Engine type Rotation speed Clutch engagement speed Idle speed Cutting width Weight Collect box bag Grass box material Cutting Height Number of height positions Self propelled Oil tank capacity Fuel tank capacity Diameter front wheel Diameter rear wheel Crank engine Central Adjustable height setting Spark Plug Type Ball bearing wheels Ready start engine Front carrying handle Foldable handle E10 fuel proof 5 Functions B amp S 126T 1901V3 BRIGGS amp STRATTON 4STROKE ENGINE 2800 min 560 mm 39 8 kg 7OL NYLON 25 75 mm 7 Yes 0 6L TL 200 mm 280 mm Full Yes CHAMPION Yes Yes Yes Yes Yes Side discharge Mulching function Rear discharge Edge cutting Collection Noise emission values measured according to relevant standard K 3 Acoustic pressure level LpA Acoustic power level LwA 82 dB A 98 dB A A ATTENTION Wear hearing protection when sound pressure is over 85 dB A aw Vibration Copyright 2015 VARO 4 3 m s2 K 1 5 m s2 Page 15 www varo com POWERPLUS Al POWXQG7556 EN Liz WARRANTY This product is wa
17. ors and or grass catchers in place Caution The lawnmower shall not be operated without either the entire grass catcher or self closing discharge opening guard in place Do not change the engine governor settings or overspeed the engine Do not alter or tamper with any sealed adjustment for the engine speed control The lawnmower safety systems or features shall not be tampered with or disabled Disengage all blade and drive clutches before starting the engine Start the engine carefully according to instructions and with feet well away from the blade s Do not tilt the lawn mower when starting the engine Do not start the engine when standing in front of the discharge chute Do not put hands or feet near or under rotating parts Keep clear of the discharge opening at all times Never pick up or carry a lawn mower while the engine is running Stop the engine and disconnect the spark plug wire make sure that all moving parts have come to a complete stop and where a key is fitted remove the key Before clearing blockages or unclogging chute Before checking cleaning or working on the lawn mower After striking a foreign object Inspect the lawnmower for damage and make repairs before restarting and operating the lawn mower If lawn mower starts to vibrate abnormally check immediately Stop the engine and disconnect the spark plug wire make sure that all moving parts have come to a complete stop and where a key is
18. p mower and disconnect spark plug cable before changing mower cutting height 2 The central height adjustment lever offers you 7 different height positions 3 To change the height of cut squeeze adjuster lever toward the wheel moving up or down to selected height Fig 13 4 All wheels will be in the same height of cut Copyright 2015 VARO Page 11 www varo com POWERPLUS Al POWXQG7556 EN 9 CLEANING AND MAINTENANCE 9 1 Spark plug Use only original replacement spark plug For best results replace the spark plug every 100 hours of use 9 2 Lubrication instructions AN CAUTION DISCONNECT SPARK PLUG BEFORE SERVICING 1 WHEELS Lubricate the ball bearings in each wheel at least once a season with a light oil 9 3 Cleaning AN CAUTION Do not hose engine Water can damage engine or contaminate the fuel system 1 Wipe deck with dry cloth 2 Hose under deck by tilting the mower so that the spark plug is up 9 3 1 Engine air cleaner CAUTION Do not allow dirt or dust to clog the air filter foam element The engine air cleaner element must be serviced cleaned after 25 hours normal mowing The foam element must be serviced regularly if the mower is used in dry dusty conditions To clean air filter Remove screw Remove cover Wash filter element in soap water DO NOT USE GASOLINE Air dry filter element Place a few drops of SAE30 oil on the foam filter and squeeze tightly to remove any excess oil 6 Reinstall fi
19. rankshaft with the star away from the engine Refer to figure 15 Place the blade with the part number facing away from the adapter Align the washer over the blade and insert the hex bolt Tighten the hex bolt to the torque listed below 9 33 Blade mounting torque Centre Bolt 40 Nm 50 Nm to insure safe operation of your unit ALL nuts and bolts must be checked periodically for correct tightness After prolonged use especially in sandy soil conditions the blade will become worn and lose some of the original shape Cutting efficiently will be reduced and the blade should be replaced Replace with an approved factory replacement blade only Possible damage resulting from blade unbalance condition is not the responsibility of the manufacturer When you change the blade you must use the original type marked on the blade 10 STORAGE INSTRUCTIONS OFF SEASON The following steps should be taken to prepare lawn mower for storage 1 Empty the tank after the last mowing of the season Empty the petrol tank with a suction pump Caution Do not drain the petrol in closed rooms in close proximity of open fire etc Do not smoke Petrol fumes can cause explosion or fire Start the engine and let it run until it has used up all remaining petrol and stalls Remove the spark plug Use an oilcan to fill approx 20 ml oil into the combustion chamber Operate the starter to evenly distribute the oil in the combustion chamber Replace the spark p
20. release the lever the engine and the blade stop automatically To mow hold the lever in the working position Before you start to mow check the start stop lever several times to be sure that it is working properly Ensure that the tension cable can be smoothly operated i e is not catching or kinking in any way gt P Go 4 To stop engine CAUTION The blade continues to rotate for a few seconds after the engine is shut off gt 1 Release the brake control handle to stop the engine and blade 2 Disconnect and ground the spark plug wire to prevent accidental starting while equipment is unattended 8 5 Auto move The mower is equipped with a speed adjusting system which can adjust 4 speeds from 3 0 km h to 4 5 km h Position 1 the slowest position Position 4 the fastest position Follow the step as mentioned below 1 Release the Self drive control handle until the lawn mower doesn t go forward 2 Adjust the appropriate speed which you want Fig 11 3 Grasp the Self drive control handle to go on mowing Fig 11 CAUTION your mower is designed to cut normal residential grass of a height no more than 250 mm Do not attempt to mow through unusually tall dry or wet grass e g pasture or piles of dry leaves Debris may build up on the mower deck or contact the engine exhaust presenting a potential fire hazard Copyright 2015 VARO Page 10 www varo com POWERPLUS SZ POWXQG7556 EN 8 6 For the best results whe
21. rranted for a 5 year period effective from the date of purchase by the first user This warranty covers all material or production flaws excluding batteries chargers defective parts subject to normal wear amp tear such as bearings brushes cables and plugs or accessories such as drills drill bits saw blades etc damage or defects resulting from maltreatment accidents or alterations nor the cost of transportation Damage and or defects resulting from inappropriate use also do not fall under the warranty provisions We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool Repairs may only be carried out by an authorised customer service centre for Powerplus tools You can always obtain more information at the number 00 32 3 292 92 90 Any transportation costs shall always be borne by the customer unless agreed otherwise In writing At the same time no claim can be made on the warranty if the damage of the device is the result of negligent maintenance or overload Definitely excluded from the warranty is damage resulting from fluid permeation excessive dust penetration intentional damage on purpose or by gross carelessness inappropriate usage use for purposes for which the device is not suitable incompetent usage e g not following the instructions given in the manual inexpert assembly lightning strike erroneus net voltage This list is not exhaustive Accep
22. t uses 7 2 1 Retrofitting for mulching mower WARNING only with a stopped motor and standstill cutter 1 Raise the rear cover and remove the grass catch bag Fig 7A 2 Push the mulching wedge into the deck Lock the mulching wedge with the button into the opening on the deck Fig 7B 3 Lower the rear cover again 7 2 2 Reseiting for side discharge mowing AN WARNING only with a stopped motor and standstill cutter Lift the rear cover and remove the grass catch bag Mount the discharge channel Lift sideward flap for side discharge Fig 8A Mount the discharge guide for side discharge on the support pin of the sideward flap Fig 8A Lower the sideward flap the flap lies on the discharge channel Fig 8B Ewu pi 7 2 3 Mowing with the grass catch bag AN WARNING only with a stopped motor and standstill cutter 1 For mowing with the grass catch bag remove the mulching wedge and discharge channel for side discharge and mount the grass catch bag 2 Removing the mulching wedge Lift rear cover and remove the mulching wedge Removing the discharge guide for side discharge Copyright 2015 VARO Page 8 www varo com POWERPLUS gt _ POWXQG7556 EN 3 Lift sideward flap and remove discharge channel The sideward flap automatically closes the discharge opening on the housing by mean of spring force Regularly clean the sideward flap and discharge opening form grass rest and stuck dirt 7
23. tance of claims under warranty can never lead to the prolongation of the warranty period nor commencement of a new warranty period in case of a device replacement Devices or parts which are replaced under the warranty therefore remain the property of Varo NV We reserve the right to reject a claim whenever the purchase cannot be verified or when it is clear that the product has not been properly maintained Clean ventilation slots carbon brushes serviced regularly etc Your purchase receipt must be kept as proof of date of purchase Your appliance must be returned undismantled to your dealer in an acceptably clean state in its original blow moulded case if applicable to the unit accompanied by proof of purchase 16 ENVIRONMENT Should your appliance need replacement after extended use do not discard it with the household rubbish but dispose of it in an environmentally safe way Please dispose of used motor oil in a manner that is compatible with the environment We suggest you take it in a sealed container to your local service station for reclamation Do not throw it in the trash or pour it on the ground Copyright 2015 VARO Page 16 www varo com POWERPLUS Al POWXQG7556 EN 17 DECLARATION OF CONFORMITY VARON V Joseph Van Instraat 9 BE2500 Lier BELGIUM declares that Product Self propelled lawn mower 190 cc 560 mm Trade mark POWERplus Model POW XQ7556 is in conformity with the essential requirements
24. ts to consult their physician and the medical implant manufacturer before operating this machine 5 1 Training Read the instructions carefully Be familiar with the controls and the proper use of the equipment Never allow children or people unfamiliar with these instructions to use the lawn mower Local regulations can restrict the age of the operator Never mow while people especially children or pets are nearby Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property The operators must receive proper training in the use adjustment and operation of the machine including prohibited operations 5 2 Preparation While mowing always wear substantial footwear and long trousers Do not operate the equipment when barefoot or wearing open sandals Thoroughly inspect the area where the equipment is to be used and remove all objects hich can be thrown by the machine WARNING Petrol is highly flammable Store fuel in containers specifically designed for this purpose Refuel outdoors only and do not smoke while refuelling Add fuel before starting the engine Never remove the cap of the fuel tank or add petrol while the engine is running or when the engine is hot f petrol is spilled do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until petrol vapours have dissipated
25. wing leaves make sure they are dry and are not laying too thick on the lawn Do not wait for all the leaves to be off the trees before you mow WARNING if you strike a foreign object stop the engine Remove wire from spark plug thoroughly inspect the mower for any damage and repair the AN damage before restarting and operating the mower Extensive vibration of the mower during operation is an indication of damage The unit should be promptly inspected and repaired 8 7 Grass catcher There is a window on the rear cover You can see the condition of grass catcher through the window If the catcher is full of grass you will empty and clean the bag make sure it is clean and ensure its meshwork is ventilated 8 8 Deck The underside of the mower deck should be cleaned after each use to prevent a build up of grass clippings leaves dirt or other matter If this debris is allowed to accumulate it will invite rust and corrosion and may prevent proper mulching The deck may be cleaned by tilting the mower and scraping clean with a suitable tool make certain the spark plug wire is disconnected 8 9 Height adjustment instructions CAUTION Do not at any time make any adjustment to lawnmower without first stopping the engine and disconnecting the spark plug wire CAUTION before changing mowing height stop mower and disconnect spark plug cable Your mower is equipped with a central height adjustment lever offering 7 height positions 1 Sto
Download Pdf Manuals
Related Search