Kramer Electronics VM-50V
Contents
1. Connect the OUTPUTS 1 to 5 s video connectors to up to 5 acceptors for example s video recorders Connect the 12V DC power supply to the unit not shown in the illustration and then to the mains electricity Switch on the power s Video s Video Recorder 5 Recorder 5 Figure 10 Connecting the VM 50YC 1 5 s Video Distributor 1 Switch OFF the power on each device before connecting it to your VM 50YC After connecting switch on the VM 50YC power and then switch on the power on each device 2 You are not required to connect all the acceptors 16 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 6 Technical Specifications Tables 6 to 10 list technical specifications for the distributors Table 6 VM 2N Technical Specifications INPUT 1 composite video DC coupled 1Vpp 75Q on a BNC connector 1 audio stereo balanced mono 4dBu 50kQ on RCA connectors OUTPUT 2 composite video 1Vpp 75Q on BNC connectors 2 audio stereo balanced mono 4dBu 50Q on RCA connectors MAX AUDIO LEVEL 3dB 22dBu VIDEO BANDWIDTH Exceeding 400MHz AUDIO BANDWIDTH gt 100kHz 1dB DIFFERENTIAL GAIN lt 0 05 DIFFERENTIAL PHASE 0 1Deg K FACTOR lt 0 05 S N RATIO Better than 85dB audio 75dB video SDI EFF RANGE Up to 50 meters AUDIO THD N 0 017 POWER SOURCE 230V AC 50Hz 115V AC USA 4 6VA DIMENSIONS 16 5cm x 12cm x 4 5cm 6 5 x2. e Level and equalization controls e AC power supply e Compact desktop size The VM 5S Video Audio Distributor The Kramer VM SS is a high performance distribution amplifier for composite or SDI video and unbalanced stereo audio signals It takes one input provides correct buffering and isolation and distributes the signal to 5 identical outputs More specifically the VM S5S features e High bandwidth of 340MHz 3dB e video input and 5 outputs on BNC connectors e unbalanced stereo input and 5 outputs on RCA connectors e Looped input capability e Selectable input signal termination e Audio level video level and equalization controls e AC power supply e Compact desktop size KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 3 3 4 3 5 The VM 50HN Headphone Distributor The Kramer MultiTOOLS VM 50HN is a high performance distribution amplifier for headphone signals It takes one stereo headphone input and distributes the signal to five identical stereo headphone outputs More specifically the VM 50HN features e mono stereo audio input and 5 outputs on 6 5mm phone connectors with mono stereo selector e Level gain controls for each output e Power LED indicator e 12V DC power supply e MultiTOOLS size The VM 50V 1 5 Video Distributor The Kramer VM 50V is a high performance distribution amplifier for composite or SD I signals It takes one input provides correct buffering and isolation and di
3. 4 7 x 1 8 W D H ACCESSORIES Power cord WEIGHT 0 620kg 1 3lbs approx OPTIONS RK 1 19 rack adapter Table 7 VM 50HN Technical Specifications INPUT 1 audio stereo 1Vpp 50kQ on a 6 5mm phone connector OUTPUTS 5 audio stereo 500mW 80 on 6 5mm phone connectors AUDIO BANDWIDTH 3dB 25kHz CONTROL 5 stereo output level controls front 1 mono switch rear GAIN RANGE 600B to 10dB S N RATIO 78dB THD 0 08 100mW POWER SOURCE 12V DC 370mA nom 1A max DIMENSIONS 16 5cm x 12cm x 4 5cm 6 5 x 4 72 x 1 77 W D H WEIGHT 0 68kg 1 5lbs approx ACCESSORIES 12V DC power supply OPTIONS RK 13 19 rack adapter 1 Specifications are subject to change without notice 17 Technical Specifications Table 8 VM 5S Technical Specifications INPUT 1 video AC DC coupled internal jumper looping 1Vpp 75 Q on BNO connectors with rear termination switch 1 audio stereo mono balanced up to 21V 50k Q on RCA connectorg OUTPUTS 5 video 1 Vpp 75 Q on BNC connectors 5 audio stereo balanced mono up to 21V 220 Q on RCAoonectors MAX VIDEO OUTPUT 1 7 Vpp VIDEO BANDWIDTH 3dB 340MHz AUDIO BANDWIDTH 3dB 20kHz DIFF GAIN 0 05 DIFF PHASE 0 1Deg K FACTOR 0 05 VIDEO S N RATIO 75dB AUDIO S N 82dB 1V COUPLING DC AC internally selectable AUDIO THD 0 009 SD
4. the level KRAMER SIMPLE CREATIVE TECHNOLOGY Your Distributor 4 3 Your VM 50HN Headphone Distributor Figure 3 and Table 3 define the VM 50HN 22 TI INPUT Our1 Ourz Ours QuT4 Ours 1 De MultiTooLS Ly U LEVEL CONTROL POWER Our Our2 ours Qur OuT5 Mono o 0 Go Headphone Distributor VM SOHN Figure 3 VM 50HN Headphone Distributor Table 3 VM 50HN Headphone Distributor Feature Function 1 INPUT 6 5mm phone connector Connects to the input source 2 OUT 6 5mm phone connectors Connect to the headphones 1 to 5 3 12V DC Connector Connects to the 12V DC power supply 4 POWER LED llluminates when the unit is ON 5 LEVEL CONTROL Potentiometers Adjust the audio signal output level OUT 1 to OUT 5 6 MONO Pushbutton Press IN for mono audio leave OUT for stereo audio Rotate to adjust the appropriate level 1 Your Distributor 4 4 Your VM 50V 1 5 Video Distributor Figure 4 and Table 4 define the VM 50V 41 5 Video Distributor VM 50V INPUT IN rare EQ LEVEL Figure 4 VM 50V 1 5 Video Distributor Table 4 VM 50V 1 5 Video Distributor Feature Function 1 Illuminated Power Switch Illuminated switch for turning the unit ON or OFF 2 TERM Pushbutton Switch Press IN for 75Q input ter
5. 12 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the Distributors 5 2 Connecting the VM 5S Video Audio Distributor To connect the VM 58 as shown in Figure 7 do the following 1 Connect the input video source for example a video player to the VIDEO IN BNC connector Connect the input audio source for example the audio from the video player to the AUDIO IN RCA connectors noting the right and left channels Connect the VIDEO OUT 1 to 5 BNC connectors to up to 5 acceptors for example video recorders Connect the AUDIO OUT 1 and 5 RCA connectors to up to 5 acceptors for example the audio input on the video recorders For normal use the input loop is not used press IN the TERM pushbutton to add a 75Q termination to the line If an input loop is used release the TERM pushbutton Connect the power cord to the unit not shown in the illustration and then to the mains electricity Switch on the power If needed adjust the AUDIO LEVEL and VIDEO LEVEL and EQ controls on the underside of the unit see Figure 2 Audio Connections are not shown Video Player Video Recorder 1 Video Recorder 5 Figure 7 Connecting the VM 5S Video Audio Distributor 1 Switch OFF the power on each device before connecting it to your VM 5S After connecting switch on the VM 5S power and then switch on the power on each device 2 You are not required to connect all the acceptors 3 Use the power cord supplied with
6. I EFFECTIVE RANGE Up to 70 meters POWER SOURCE 230V AC 50 60Hz 115V U S A 3 5VA DIMENSIONS 22cm x 18cm x 4 5cm 8 7 x 7 x 1 8 W D H half 19 WEIGHT 1 4kg 3 3lbs approx ACCESSORIES Power cord OPTIONS RK 1 19 rack adapter Table 9 VM 50V Technical Specifications INPUT 1 video looping 1Vpp 75 on BNC connectors with a termination switch OUTPUTS 5 video 1Vpp 75 Q on BNC connectors MAX VIDEO OUTPUT 2Vpp VIDEO BANDWIDTH 3dB 480MHz DIFF GAIN 0 05 DIFF PHASE 0 12Deg K FACTOR lt 0 05 S N RATIO 73dB CONTROL 750 termination switch COUPLING AC POWER SOURCE 12V DC 40mA DIMENSIONS 16 5cm x 12cm x 4 5cm 6 5 x 4 7 x 2 8 W D H WEIGHT 0 62kg 1 4lbs approx ACCESSORIES 12V DC power supply brackets for stacking multiple units OPTIONS RK 1 19 rack adapter 18 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications Table 10 VM 50YC Technical Specifications INPUT 1 s Video looping 1Vpp 75 Q Y 0 3 Vpp 75Q C on gin connectors with a termination switch OUTPUTS 5 s Video 1Vpp 75 Q Y 0 3 Vpp 75Q C on 4pin connectors MAX VIDEO OUTPUT 2Vpp Y s VIDEO BANDWIDTH 3dB 285MHz Y DIFF GAIN 0 05 DIFF PHASE 0 05Deg K FACTOR 0 05 S N RATIO 80dB CONTROL 750 termination switch COUPLING AC POWER SOURCE 12V DC 50mA DIMENSIONS 16 5cm x 12cm x 4 5cm 6 5 x 4 7 x 2 8 W D H
7. Kramer Electronics Ltd USER MANUAL Models VM 2N Video Audio Distributor VM 5S Video Audio Distributor VM 50HN Headphone Distributor VM 50V 1 5 Video Distributor Vv M 50YC 1 5 s Video Distributor Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 3 1 The VM 2N Video Audio Distributor 3 2 The VM 5S Video Audio Distributor 3 3 The VM 50HN Headphone Distributor 3 4 The VM 50V 1 5 Video Distributor 3 5 The VM 50YC 1 5 s Video Distributor 4 Your Distributor 4 1 Your VM 2N Video Audio Distributor 4 2 Your VM 5S Video Audio Distributor 4 3 Your VM 50HN Headphone Distributor 4 4 Your VM 50V 1 5 Video Distributor 4 5 Your VM 50YC 1 5 s Video Distributor 5 Connecting the Distributors 5 1 Connecting the VM 2N Video Audio Distributor 5 2 Connecting the VM 5S Video Audio Distributor 5 3 Connecting the VM 50HN Headphone Distributor 5 4 Connecting the VM 50V 1 5 Video Distributor 59 Connecting the VM 50YC 1 5 s Video Distributor 6 Technical Specifications Figures Figure 1 VM 2N Video Audio Distributor Figure 2 VM 5S Video Audio Distributor Figure 3 VM 50HN Headphone Distributor Figure 4 VM SOV 1 5 Video Distributor Figure 5 VM SOYC 1 5 s Video Distributor Figure 6 Connecting the VM 2N Video Audio Distributor Figure 7 Connecting the VM 5S Video Audio Distributor Figure 8 Connecting the VM 50HN Headphone Distributor Figure 9 Connecting the VM 50V 1 5 Video Distri
8. WEIGHT 0 58kg 1 3lbs approx ACCESSORIES 12V DC power supply brackets for stacking multiple units OPTIONS RK 1 19 rack adapter 19 LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty ll Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with Damage deterioration or mal function resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the produc
9. butor Figure 10 Connecting the VM 50YC 1 5 s Video Distributor 0 JA UA Uh HL Ni m m gt gt ja an NN DU WN RB KF OO 10 11 12 13 14 15 16 Contents Tables Table 1 VM 2N Video Audio Distributor Table 2 VM 5S Video Audio Distributor Table 3 VM 50HN Headphone Distributor Table 4 VM 50V 1 5 Video Distributor Table 5 VM 50YC 1 5 s Video Distributor Table 6 VM 2N Technical Specifications Table 7 VM 50HN Technical Specifications Table 8 VM 5S Technical Specifications Table 9 VM 50V Technical Specifications Table 10 VM 50YC Technical Specifications 10 11 17 17 18 18 19 ii KRAMER SIMPLE CREATIVE TECHNOLOGY Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Thank you for purchasing the Kramer VM 2N VM 5S VM 50HN VM 50V VM 50YC Video Distribution Amplifiers which are ideal for e Any professional A V system requiring a compact high quality DA e Retail stores and other point of sale display systems e Security and CCTV applications e Studio RGB YUV distribution Ea
10. ch package includes the following items e The VM 2N VM 5S VM 50HN VM 50V or VM 50YC e Power cord or power adapter 12V DC input e This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 We recommend that you use only the power cord supplied with this device 3 Download up to date Kramer user manuals from our Web site at http www kramerelectronics com 4 The complete list of Kramer cables is on our Web site at http www kramerelectronics com 1 Getting Started 2 1 Quick Start This quick start chart summarizes the basic setup and operation steps Step 1 Connect the Machines ria 1 Connect the video Input Connect the video outputs Connect the audio inputs Connect the audio outputs sy Composite Composite Composite Video Player Video Recorder 1 Video Recorder 2 Connect the video input Connect the video ou
11. cts is limited to the repair or replacement of the product at our option Kramer shall not be liable for T Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and lightindustry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION amp Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufactur
12. er will void user authority to operate the equipment Use the supplied DC power supply to feed power to the machine Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products 20 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution AAA NN Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000535 REV 3
13. mination leave OUT for no termination 3 INPUT IN BNC Connector Connects to the video source 4 INPUT LOOP BNC Connector Connects to an additional monitor 5 OUTPUTS BNC Connectors Connect to the video acceptors from 1 to 5 6 12V DC Connector Connects to the 12V DC power supply 7 LEVEL Control underside Adjust the audio signal output level 8 EQ Control underside Adjust the cable compensation equalization level 1 Insert a small screwdriver into the hole and carefully rotate it to trim the level 10 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the Distributors 4 5 Your VM 50YC 1 5 s Video Distributor Figure 5 and Table 5 define the VM 50YC POWER 1 5 s Video Distributor VM 50YC LPP Figure 5 VM 50YC 1 5 s Video Distributor Table 5 VM 50YC 1 5 s Video Distributor Feature Function 1 Illuminated Power Switch Illuminated switch for turning the unit ON or OFF 2 TERM Pushbutton Switch Press IN for 75Q input termination leave OUT for no termination 3 INPUT IN s Video Connector Connects to the s Video source 4 INPUT LOOP s Video Connector Connects to an additional monitor 5 OUTPUTS s Video Connectors Connect to the s Video acceptors from 1 to 5 6 12V DC Connector Connects to the 12V DC power supply 5 Connecting the Distributors This section describes how to connect the e VM 2N Video Audio Distributor see section 5 1 e VM 5S Video Audio Distributo
14. nlight and dust 4 Your Distributor This section describes the e VM 2N Video Audio Distributor see section 4 1 e VM 5S Video Audio Distributor see section 4 2 e VM 50HN Headphone Distributor see section 4 3 e VM 50V 1 5 Video Distributor see section 4 4 e VM 50YC 1 5 s Video Distributor see section 4 5 1 For example part number 22535 00025 1 2 Available from Kramer Electronics on our Web site at http www kramerelectronics com 6 KRAMER SIMPLE CREATIVE TECHNOLOGY Your Distributor 4 1 Your VM 2N Video Audio Distributor Figure 1 and Table 1 define the VM 2N POWER Video Audio Distributor VM 2N VIDEO 2999 F OF ee Figure 1 VM 2N Video Audio Distributor Table 1 VM 2N Video Audio Distributor Feature Function 1 Illuminated Power Switch Illuminated switch for turning the unit ON or OFF 2 VIDEO INBNC Connector Connects to the video source 3 VIDEO OUT BNC Connectors Connect to the video acceptor from 1 to 2 4 AUDIO IN RCA Connectors L and R Connect to the L and R channels of the audio source 5 AUDIO OUT RCA Connectors L and R Connect to the L and R channels of the audio acceptor from 1 to 2 6 Power Connector with Fuse AC connector for supplying power to the unit 7 LEVEL Control underside Adjust the audio signal output level 8 EQ Control underside Adjust the cable compensation equali
15. r see section 5 2 e VM 50HN Headphone Distributor see section 5 3 e VM 50V 1 5 Video Distributor see section 5 4 e VM 50YC 1 5 s Video Distributor see section 5 5 11 Connecting the Distributors 5 1 Connecting the VM 2N Video Audio Distributor To connect the VM 2N as shown in Figure 6 do the following 1 Connect the input video source for example a composite video player to the VIDEO IN BNC connector Connect the input audio source for example the audio from a composite video player to the AUDIO IN RCA connectors noting the right and left channels Connect the VIDEO OUT 1 and 2 BNC connectors to up to 2 acceptors for example composite video recorders Connect the AUDIO OUT 1 and 2 RCA connectors to up to 2 acceptors for example the audio input on the composite video recorders Connect the power cord to the unit not shown in the illustration and then to the mains electricity Switch on the power If needed adjust the LEVEL ands EQ controls on the underside of the unit see Figure 1 Composite Composite Composite Video Player Video Recorder 1 Video Recorder 2 Figure 6 Connecting the VM 2N Video Audio Distributor 1 Switch OFF the power on each device before connecting it to your VM 2N After connecting switch on the VM 2N power and then switch on the power on each device 2 You are not required to connect two acceptors 3 Use the power cord supplied with the unit
16. stributes the signal to five identical outputs More specifically the VM 50V features e High bandwidth of 480MHz 3dB e video input 1 looping input and 5 outputs on BNC connectors e Selectable input signal termination e Signal level and equalization controls e 12V DC power supply e Compact desktop size The VM 50YC 1 5 s Video Distributor The Kramer VM 50YC is a high performance distribution amplifier for s Video Y C signals It takes one input provides correct buffering and isolation and distributes the signal to 5 identical outputs More specifically the VM 50YC features e High bandwidth Y of 285MHz 3dB e looping input and 5 outputs on 4 pin connectors e Selectable input signal termination e 12V DC power supply e Compact desktop size Your Distributor No operator serviceable parts inside unit Use only the Kramer Electronics input power wall adapter that is provided with this unit a Disconnect power and unplug unit from wall before installing or removing device or servicing unit To achieve the best performance e Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances that may adversely influence signal quality and position your Kramer product away from moisture excessive su
17. t claims must be presented to the carrier v Removalorinstallation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILLPAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following l 2 3 Removal or installations charges Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased Shipping charges HOW YOU CAN GET WARRANTY SERVICE Ty 2 3 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All the implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective produ
18. the unit 13 Connecting the Distributors 5 3 Connecting the VM 50HN Headphone Distributor To connect the VM 50HN as shown in Figure 8 do the following 1 Connect the input audio source for example a stereo audio player to the INPUT 6 5mm phone connector 2 Connect the OUT 1 to OUT 5 6 5mm phone connectors to up to 5 2 acceptors for example stereo headphones or speakers 3 Set the MONO pushbutton OUT for stereo operation and press IN for mono Operation see Figure 3 4 Connect the 12V DC power supply to the unit not shown in the illustration and then to the mains electricity Switch on the power 5 Adjust the volume for each output using a small screwdriver to turn the potentiometers on the front panel see Figure 3 Stereo Audio Source Speakers Headphones Figure 8 Connecting the VM 50HN Headphone Distributor 1 Switch OFF the power on each device before connecting it to your VM SOHN After connecting switch on the VM SOHN power and then switch on the power on each device 2 You are not required to connect all the acceptors 14 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the Distributors 5 4 Connecting the VM 50V 1 5 Video Distributor To connect the VM 50V as shown in Figure 9 do the following 1 Connect the input video source for example a composite video player to the INPUT IN BNC connector If looping the input to another device connect a video acceptor for e
19. tputs Connect the audio inputs Connect the audio outputs are not shown Video Player Video Recorder 1 Video Recorder 5 Step 2 Connect the power If required O Adjust the EQ and LEVEL KRAMER SIMPLE CREATIVE TECHNOLOGY Getting Started Step 1 Connect the Machines E Composite Video Composite Video Composite Video Player Recorder 1 Recorder 5 s Video Recorder 5 1 Connect the video input 2 Connect the video outputs Quick Start VM 50HN Connect the stereo audio input Connect the stereo audio outputs Stereo Audio Source Speakers Headphones Step 2 Connect the power If required O Adjust the EQ and LEVEL Overview 3 1 3 2 Overview This section gives an overview of the e VM 2N Video Audio Distributor see section 3 1 e VM 5S Video Audio Distributor see section 3 2 e VM 50HN Headphone Distributor see section 3 3 e VM 50V 1 5 Video Distributor see section 3 4 e VM 50YC 1 5 s Video Distributor see section 3 5 The VM 2N Video Audio Distributor The Kramer VM 2N is a high performance distribution amplifier for composite or SDI video and unbalanced stereo audio signals It takes one input provides correct buffering and isolation and distributes the signal to two identical outputs More specifically the VM 2N features e High bandwidth Y of 400MHz 3dB e 1 composite video input and 2 outputs on BNC connectors e unbalanced stereo input and 2 outputs on RCA connectors
20. xample a monitor to the INPUT LOOP BNC connector If the input loop is not used press IN the TERM pushbutton to add a 759 termination to the line If an input loop is used release the TERM pushbutton Connect the VIDEO OUT 1 to 5 BNC connectors to up to 5 acceptors for example composite video recorders Connect the 12V DC power supply to the unit not shown in the illustration and then to the mains electricity Switch on the power If needed adjust the LEVEL and EQ controls on the underside of the unit see Figure 4 Composite Video Composite Video Composite Video Player Recorder 1 Recorder 5 Figure 9 Connecting the VM 50V 1 5 Video Distributor 1 Switch OFF the power on each device before connecting it to your VM 50V After connecting switch on the VM 50V power and then switch on the power on each device 2 You are not required to connect all the acceptors 15 Connecting the Distributors 5 5 Connecting the VM 50YC 1 5 s Video Distributor To connect the VM 50YC as shown in Figure 10 do the following Ls 1 Connect the input video source for example an s video player to the INPUT IN s video connector If looping the input to another device connect a video acceptor for example an s video monitor to the INPUT LOOP s video connector If the input loop is not used press IN the TERM pushbutton to add a 759 termination to the line If an input loop is used release the TERM pushbutton
21. zation level 1 Insert a small screwdriver into the hole and carefully rotate it to trim the level Your Distributor 4 2 Your VM 5S Video Audio Distributor Figure 2 and Table 2 define the VM 5S POWER Vides Audio Distributor VM 55 oo o 8 8 5 l i J J Jl JJ T T T T I a e jej e ej 8 Figure 2 VM 5S Video Audio Distributor Table 2 VM 5S Video Audio Distributor Feature Function 1 Illuminated Power Switch Illuminated switch for turning the unit ON or OFF 2 AUDIO OUT RCA Connectors Connect to the audio acceptor from 1 to 5 3 Power Connector with FUSE AC connector for supplying power to the unit 4 VIDEO IN BNC Connector Connects to the video source 5 TERM Pushbutton Switch Press IN for 75Q input termination leave OUT for no termination 6 VIDEO OUT BNC Connectors Connect to the video acceptors from 1 to 5 7 AUDIO IN RCA Connectors L and R Connect to the L and R channels of the audio source 8 AUDIO LEVEL ADJUST L and R Adjust the audio signal output level 9 VIDEO EQ Control underside Adjust the cable compensation equalization level 10 VIDEO LEVEL Control underside Adjust the video signal output level 1 Insert a small screwdriver into the hole and carefully rotate it to trim
Download Pdf Manuals
Related Search