Ergotron StyleView
Contents
1. 448mm CPU Compartment lt 2 75 70 gt 7 75 lt 21 75 197 lt 12 25 lt 1 38 Front View 311 35 mm 12 25 311 gt gt 2 75 When figuring dimensions include 70 mm mounted accessories protruding cables and port replicators or docking stations lt 13 gt 330 mm Top View Side View Auto Lock Drawer 315 mm 12 6 24 4 320 620 mm Front View Side View 888 24 318 G 00 rev C 12 14 552 mm 17 75 gt 4 25 108 mm 451 395 pom 5 28 CAUTION Completely release brake engagement before raising or lowering the cart Raising or lowering the cart with the brake partially engaged may cause product damage 6 28 888 24 318 G 00 rev 12 14 Set up Battery Charge Discharge 4 Initial Power on Charge Battery takes approximately 7 hours to charge el Plug Cart s Power Cord into wall outlet b Turn on power system by holding power button down for 1 3 seconds C With cart s power cord plugged into the wall outlet wait until cart is at 10096 charge takes aproximately up to 7 hours to charge Do Not stretch coiled cord further than 8 feet 2 5 meters damage to the cord may occur N CAUTION There is no on off switch on this equipment the AC pow2. 5 Remove cover to access Lift Tension Adjustment point 6 Attach second medical safety device analyzer probe to Lift Tension Adjustment point on Cart 7 Perform Test 25 amps 8 Ensure Earth Bond is less than or equal to 0 2 ohms 9 Remove medical device safety analyzer connections to Cart replace cover over Lift Tension Adjustment point return the Cart to service SED Insulation Resistance Test To ensure mains power lines are adequately insulated from earth ground the Do Not Plug More Than SPECIFIED NUMBER OF WATTS Into Power System Do Not Run Cord Through Doorways Holes in Ceilings Walls or Floors FULLY INSERT Plug Into Outlet Do Not Remove Bend or Modify Any Metal Prongs or Pins of Cord Do Not Use Excessive Force to Make Connections Keep Away From Water DO NOT USE WHEN WET Keep Children Away From Cord Do Not Plug Cord into An Extension Cord AVOID OVERHEATING Uncoil Cord and Do Not Cover It With Any Material Do Not Drive Drag or Place Objects Over Cord Do Not Walk On Cord GRASP PLUG to REMOVE FROM Outlet Do Not Unplug By Pulling On Cord 888 24 318 G 00 rev C 12 14 following test although not mandatory is recommended to be performed annually using a calibrated medical device safety analyzer The procedure is as follows 1 Disconnect the cart from mains power unplug cart from the wall 2 Remove power from internal power system outlets by pressing the p
3. 888 24 318 G 00 12 14 Set up 15 Place computer and AC power adaptors in compartment Do not place power bricks near computer or compartment air vents 888 24 318 G 00 rev C 12 14 15 28 Set up Plug the following factory connected cables into your computer C USB This cable runs from the USB Hub to your computer and uses your computer to power the USB Hub Keyboard Lights and Fan NOTE Your computer must be turned on for the USB Hub Keyboard Lights and Fan to function Optional StyleLink This USB cable runs from the power system to your computer for StyleLink Software For more info on StyleLink visit http 4support ergotron com Ethernet This cable runs from the side of the enclosure to your computer to allow network connection from the ethernet port on the outside of the enclosure WARNING Fan must always be running when computer is on Operating computer without fan may lead to overheating resulting in reduced equipment performance Placement of CPU s in Secure Storage Area USFF Ultra Small Form Factor Thin Client DO NOT OBSTRUCT AIR VENTS Obstructing air vents may cause overheating and result in equipment damage Center CPU in storage area To increase space and improve airflow power brick may be stored under the storage area If computer with cables
4. fields should be at levels 50 60 Hz characteristic of a typical 1 651 681 7600 info eu ergotron com Magnetic Field location in a typical commercial www ergotron com IEC 61000 4 8 or hospital environment sales ergotron com Note Ur is the AC mains voltage prior to application of the test level APAC Sales Worldwide OEM Sales Tokyo Japan www ergotron com www ergotron com info cem ergotron com apaccustomerservice ergotron com ERGOTRON 2014 Ergotron Inc All rights reserved While Ergotron Inc makes every effort to provide accurate and complete information on the installation and use of its products it will not be held liable for any editorial errors or omissions including those made in the process of translation from English to another language or for incidental special or consequential damages of any nature resulting from furnishing this instruction and performance of equipment in connection with this instruction Ergotron Inc reserves the right to make changes in the product design and or product documentation without notification to its users For the most current product information or to know if this document is available in languages other than those herein please contact Ergotron No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written consent of Ergotron Inc 1181 Trap
5. is too wide then follow these instructions 16 28 888 24 318 G 00 12 14 p SSF SSS eJ ZS age due 2 271 EX Y A 5 2 2 4 e oZ gt gt gt 4 2 57 888 24 318 G 00 rev 12 14 17 28 18 28 Keyboard Light 1 Turn Computer on 2 Test Keyboard Light Keyboard Light will automatically turn off after 15 minutes if not manually turned off 888 24 318 G 00 rev C 12 14 Adjustment product resulting in a change in the weight of the mounted load you should repeat these adjustment steps to ensure safe and optimum operation Adjustments should move smoothly and easily through the full range of motion and stay where you set it If adjustments are difficult and do not stay in the desired position follow the instructions to loosen or tighten the tension to create a smooth easy adjustment motion Depending on your product and the adjustment it may take several turns to notice a difference 2 1 It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps Any time equipment is added or removed from this Lift Up and down Release Brake to move riser CUSTOMER LIFT TENSION A AFTER SET UP SEE MANUAL 822 421 00 Q Follow these instructions to tighten or loosen tension d 14mm 9 16 NOTE Adjustment may require 40 60 b R revoluti
6. 4 How to Change Power System Batteries WARNING risk OF ELECTRICAL DISCHARGE NOT swap battery cables doing so will cause arcing and trip the circuit breaker BATTERY REPLACEMENT REMPLACEMENT DE LA BATTERIE Do not remove or replace the batteries while cart is located The power module is configured for two 33 Ah batteries Le module d alimentation est configur pour deux batteries 33 A h an rich or hazardous environment arcing may occur and Only the following batteries are compatible with this Seules les batteries suivantes sont compatibles avec ce syst me yg g may BATTERY system B amp B EP33 12 e SBS 5 12330 cause combustion B amp B EP33 12 5855 12330 Longway 6FM33G Vision 6FM33D Replace first battery before removing second battery to reduce Longway 6FM33G Vision 6FM33D Vision PBQ 033 121 the risk of cables touching terminals and causing arcing Vision 6FM33HD X PBQPBQ33 12L e Werker WKA12 33C Werker WKA12 35C Werker WKA12 33 Werker WKA12 35C e Duracell Dura 12 35C Duracell Dura 12 35C l installation de batteries autres que les batteries 33 A h cit es Always replace both batteries Installing batteries other than the 33 Ah listed above will ci dessus annulera la garantie du produit Si vous ne vous conformez Replace first battery before removing secon d battery void the product warranty Failure to heed th
7. Ethernet port outside for easy network connection Keyboard tray slides out tilts and allows for right or left mousing with attached mouse holder Keyboard Light under Front Handle Keyboard Light Switch Cable Management and Storage for excess cables and power supplies Storage Basket and Rear Handle Locking Casters Quick Reference Card Power Cord Hooks Scanner Holder Antimicrobial worksurface and antimicrobial coating on wrist rest Auto Lock Drawer Storage Drawer includes dividers 3 USB ports inside and 2 USB ports on back of drawer 6 max USB cable length for stored devices Camera Shelf camera is supplied by customer CPU Holder for codec Holds components 1 38 3 75 35 95 mm thick Outlet Box includes 2 power outlets North America Medical Grade 120VAC 60 Hz 3 A max Europe UK 230VAC 50 Hz 1 5 A max Saudi Arabia 220VAC 60 Hz 1 5 A max Power System The StyleView AC Power System allows your power supply to travel with the cart The Power System is integrated in the base of the cart and comes standard with 2 batteries power module User Interface UI outlet box and power cord User Interface 01 Allows power system output to be turned on or turned off monitors battery charge remaining and provides low battery charge audible alarm Two 33 Sealed Lead Acid Absorbed Glass Mat 12VDC batteries minimum operational temperature is 10 C 50 F and the maximum operationa
8. Immunity The Powered Computer Cart is intended for use in the electromagnetic environment specified below The customer or the user of the Powered Computer Cart should assure that it is used in such an environment Immunity Test IEC 60601 Compliance Electromagnetic environment Test Level Level guidance Electrostatic 6 kV contact Complies Floors should be wood Discharge ESD 8 kV air concrete or ceramic tile If floors IEC 61000 4 2 are covered with synthetic material the relative humidity should be at least 3096 Electrical Fast 2 kV for power supply lines Complies Mains power quality should be Transient Burst 1 kV for input output lines that of a typical commercial or IEC 61000 4 3 hospital environment Surge 1 kV differential mode Complies Mains power quality should be IEC 61000 4 5 2 kV common mode that of a typical commercial or hospital environment Voltage 590 Complies Mains power quality should be Dips short 295 dip in Ur for 0 5 cycle that of a typical commercial or interruptions 4096 Ur hospital environment and voltage 6096 dip in Ur for 5 cycles variations on 70 Ur power supply 3096 dip in Ur for 25 cycles Americas Sales and input lines 596 Ur Corporate Headquarters Sales IEC 61000 4 11 29596 dip in Ur for 5 seconds 1181 Trapp Rd Amersfoort The Netherlands Power Complies Power frequency magnetic SI Paul MN USA 800 888 8458 www ergotron com Frequency
9. User Guide StyleView SV44 Telemedicine Cart with Dual LCD and Power System Ss 7 e L EN StyleView powered carts provide electrical AC power for mobile point of care computing equipment in a healthcare environment The carts are not intended to power medical products or devices Outlets are provided to power information technology equipment only such as computer equipment computer peripherals and teleconferencing system equipment Components Tools sieut vivae Features amp Specifications ss sss sssssssesssesssesssesssesseesseeseeesseeeseeeeeeeeeeseeeseeeeeeeeeeeeeeeeeeeeeeees 3 4 BID E 5 Se 6 20 Battery Charge DIScharge acces ei 7 ate 19 Aut Lock DING 20 Change Fuse 5 Amp and Reset Circuit Breakers 21 Change Power System 5 22 23 Cart Storage long term short pst tado ae 24 8 25 Maintenance amp Safety 25 28 For service and warranty visit www ergotron com For local customer care phone numbers visit http contact ergotron com For the latest User Installation Guide and StyleLink Software Download please visit www ergotron com User s Guide English Gu a del usuario Espanol Manuel de l utilisateur Francais Gebrui
10. after 15 seconds All LEDs will flash green 2 Press 2 for Pharmacy PIN Entry Mode until system auto locks Once a drawer is opened the corresponding LED for that row will light solid until it is 3 Input Pharmacy PIN and press ENTER all LEDs blink green in PIN is accepted placed back into its original location 4 Pharmacy PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice If drawers are removed from cart for filling they must be replaced in the same configuration per row If they are not power must be removed and reapplied so that the drawer system reconfigures itself Unlock Drawer 2 methods NOTE All Drawers in row must be closed Storage Drawer includes dividers 3 USB ports inside and 2 USB ports before a new row can be unlocked on back of drawer 6 max USB cable length for stored devices Enter User PIN only numbers for available drawer rows flash green then press desired drawer row number e Key turn clockwise 1 4 turn Drawer Row Numbers Lock Drawer e Wait 4 seconds for lock to engage automatically NOTE Always ensure drawer is pushed in all the way and engaged with lock Drawer Troubleshooting LEDs Alarm Meaning LEDs on keypad when pressing any number 1 2 3 4 or 5 LED ON green Corresponding Drawer is open Verify DC cable is connected from cart battery harness to controller 1 2 3 4 or 5 LED flashing red and alarm sounding Corresponding Drawer is
11. ce Master PIN Mode Menu NOTE Master PIN does not open drawers Master PIN Mode Menu continued Enter Master PIN and then select one of the below numbers to enter that mode 6 1 After entering master PIN select 6 then select 1 to mute alarm 1 After entering Master PIN Select 1 to access User PIN Entry Mode 6 6 Master PIN Enter After entering master PIN select 6 then select 6 again then enter Master PIN 2 After entering Master PIN Select 2 to access Pharmacy PIN Entry Change Mode again then select Enter This will reset keypad to the factory default Master PIN as 1 2 3 4 5 and will 5 After entering Master PIN Select 5 to access Master Pin Change Mode also delete all personal PINs and Pharmacy PIN Programming User PINS 1 Enter Master PIN and press ENTER for Mode Menu 2 Press 1 for User PIN Entry Mode 3 Input new User PIN and press ENTER All LEDs blink green if PIN is accepted You may enter multiple USER PINs consecutively 4 User PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice NOTE User PIN cannot be the same as a Master PIN or Pharmacy PIN Once maximum User PIN storage is exceeded the oldest User PIN will be over written Programming Pharmacy PIN Note System will hold 1 Pharmacy PIN Pharmacy PIN allows all drawers to unlock at the same time Drawers 1 Enter Master PIN and press ENTER for Mode Menu should then be opened at least slightly as the system will auto lock
12. digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by Ergotron Inc could void the user s authority to operate the equipment Please contact Ergotron for complete EMC compatibility information LEAD ay Sd BATTERY Product was placed on the market after 13 August 2005 CAUTION Close worksurface before opening drawers Open only one drawer at a time Do Not push cart when drawers or worksurface are open Failure to follow these instructions may cause the cart to be unstable 888 24 318 G 00 rev C 12 14 20 21 22 23 Height Adjustable LCD Mount attaches LCDs or tablet PC s with 75x75 or 100x100mm mounting interface Worksurface 2a Worksurface Lock and Release User Interface for Power System Secure Storage for Laptop Thin Client or CPU Front Handle Height Adjustment Brake Handle USB Hub inside connects keyboard and mouse USB cables
13. e proximity of electrical power and equipment All paints and plastic Cart components will withstand cleaning by most commonly used diluted non abrasive solutions such as quaternary ammonia compounds ammonia enzyme cleaners bleach or alcohol solutions Pen and permanent and dry erase markers can be removed with 91 isopropyl alcohol and a soft cloth e lodine stains can be removed with commonly used cleaners and a soft cloth e Never use steel wool or other abrasive materials that will damage the surface finish Do not use strong solvents such as trichloroethylene and acetone These solvents will damage the surface finish It is recommended that any cleaning solution be tested on a small inconspicuous area to ensure surface is not harmed Adjustment Service Replacement DO NOT attempt to adjust service or replace any part of the StyleView Cart unless directed to do so through Ergotron approved documentation i e installation instructions Only Ergotron Inc or an Ergotron certified entity may adjust service or replace StyleView Cart components If any component on the Cart is missing or damaged the Cart must not be used contact Ergotron Customer Care immediately to request a replacement part Cables Keep cables neatly organized on the Cart a variety of solutions are provided with your cart for this purpose Excess cables should be routed away from moving components with cable clips Review Cable Routing section of this guide or con
14. er button for internal power system outlets Pressing this will provide or remove power to from components plugged into the internal outlets J When dark power system is off O NOTE Frequent operation of the cart while battery charge levels are below 30 will significantly reduce the life of your battery and may void your battery warranty When lit the power system is on 888 24 318 G 00 rev C 12 14 7 28 8 28 888 24 318 G 00 rev 12 14 Set up 0 USB Type A USB Type A NOTE Bar Code Scanner should be connected directly to AN computer USB port DO NOT connect Bar Code Scanner to the USB Hub 888 24 318 G 00 rev 12 14 9 28 Set up 8 Follow these instructions if you want to change the height of your LCDs to one of the 3 positions IMPACT HAZARD MOVING PARTS CAN CRUSH AND CUT to heed this warning may result in serious personal 1 X injury or property damage Raise monitor to top of vertical adjustment BEFORE removing M4 x 8mm remove Stop Screw without monitor attached Doing so will cause monitor pivot to shoot up rapidly and may cause personal injury DANGER D IMPACT LES PARTIES EN MOUVEMENT PEUVENT CRASER ET COUPER Il existe un risque de blessure corporelle ou d endommagement mat riel en cas de non respect de cet avertissement cran au plus haut de l ajustement vertical AVANT de le retirer is d arr t avant que l cra
15. er cord is the only power disconnect The socket outlet should be easily accessible and should be installed near the equipment OO 30 0 0 lt 0 100 This power system interface will alert you to the percentage of charge remaining in the cart battery with a series of steady or flashing red yellow or green lights and an alarm that will when charge gets below 30 Remember the battery needs to be charged to 100 every day and you can use the cart while charging so plug in cord as often as possible to avoid running out of power NOTE Put monitor in power save mode to optimize battery run time 100 Battery has 10096 charge a Q Light flashes when charging power cord plugged into wall outlet Allow battery to continue charging until light stops flashing After light stops flashing it is OK to unplug the power cord from the wall You can use cart while charging E un Battery has less than 90 charge Battery has less than 7096 charge Battery has less than 5096 charge ill lt 90 lt 70 lt 50 When lit alarm is enabled and will beep when battery charge gets below 3096 For details on enabling and disabling alarm contact Ergotron Customer Care 30 Battery has less than 3096 charge Light is red and alarm beeps Plug in power cord and charge to 10096 You can use cart while charging Alarm Mute button Pressing this will temporarily mute alarm Pow
16. ines BATTERY Z gt AG a m Caution onnect Red before connecting Black T Sq E 0 m 1 8 f f OF TUNG 6 Follow Battery Charge Discharge Initial Power on steps a b c 888 24 318 G 00 rev C 12 14 23 28 Cart Storage Instructions Short Term Storage Ifthe Power System will be idle for up to 3 months the battery should be fully charged before storage Long Term Storage If the Power System will be idle for 3 months or more the battery should be removed from the cart and recharged during storage Short Term Storage If the Power System will be idle for up to 3 months the battery should be fully charged before storage 1 Turn off all mounted equipment Plug power cord into appropriate wall outlet to fully charge battery to 10096 all indicator lights will be illuminated Power system must be fully charged before storing Once battery has been charged to 10096 turn power system off a Turn power system off by holding down the AC Outlet Power button for 1 3 seconds Power light will shut off b Turn both circuit breakers to OFF a ps NOTICE Warranty on fully charged batteries left in an unused state for more than three 3 consecutive months is automatically void Warranty on fully discharged batteries left in an unused state for more than three 3 consecutive days is automatically void Long Te
17. information 6 Stay in charge Powered carts should be plugged into outlet as often as possible to keep battery charged and computer running 1 v 2 Maintenance amp Safety Hazard Symbols Review The Meaning of Symbols appearing in this Guide on the Cart or on the Power System Moving stow before you go 1 During normal movement release brake and lower worksurface to lowest position for optimal stability and unobstructed view 2 Tuck away open trays and return mouse scanner and other accessories to their places 3 Unlock both front casters 4 Push cart from rear with elbows bent at about 90 to maximize control and minimize muscle strain 5 Don t run out Before moving make sure the power cord and multiple socket outlet cord are unplugged from outlet and hooked to basket for safe travel Remember charge battery fully 10096 every day nmuuuamuuamuununuum wel ED a a 5 4 4 9 J 3 These symbols alert you to a safety condition that demands your attention You should be able to recognize and EQUIPMENT amp ACCESSORIES DISPOSAL understand the significance of the following Safety Hazards if you encounter them on the Cart or within Cart documentation such as this Set up Guide Signal Word Level of Hazard Color Symbol 1 Please dispose of all batteries in accordance with local law 2 All Electronics should be recycled th
18. is warning pasa cette pr caution d utilisation les batteries et le module may result in severe damage to batteries power module d alimentation risquent d tre s rieusement endommag s ce qui Replace batteries with same Amp Hour rating batteries only and possible fire hazard pourrait provoquer un incendie Only Ergotron specified batteries may be used in the StyleView Power System Please call customer care for more details e Recycle battery or contact Ergotron for proper battery disposal guidelines www ergotron com 822 386 1 Turn off all mounted equipment b Disconnect Power System and Multiple Socket Outlet from Turn power system off by holding down power source the AC Outlet Power button for 1 3 seconds Power light will shut off 69 b Turn both circuit breakers to OFF OFF 9 ji D m a T Dl 4 Au WT I LEAD Recycle battery or contact Ergotron for proper battery aw disposal guidelines BATTERY f Caution Connect Red before connecting Black 22 28 888 24 318 G 00 rev C 12 14 How to Change Power System Batteries 4 Caution Replace only one battery at a time Do NOT swap battery cables doing so will cause sparking and trip the circuit breakers LEAD Recycle battery or contact Ergotron for proper battery disposal guidel
19. kersgids Deutsch Benutzerhandbuch Nederlands Guida per l utente Italiano www ergotron com Anvandarhandbok svenska USA 1 800 888 8458 0000006 000 Europe 31 0 33 45 45 600 0000 UU China 86 769 86018920 888 24 318 G 00 rev C 12 14 1 28 Components ee 1X x smm 4x amp M4 x 10mm 1x CE 2x 3 M4 12mm Tools Needed 2 28 888 24 318 G 00 12 14 Features amp Specifications 14mm 9 16 IMPACT HAZARD MOVING PARTS CAN CRUSH AND CUT Failure to heed this warning may result in serious personal injury or property damage Minimize Lift Tension BEFORE Removing Mounted Equipment Shipping Cart Storing Cart DANGER D IMPACT LES PARTIES EN MOUVEMENT PEUVENT CRASER ET COUPER Il existe un risque de blessure corporelle ou d endommagement mat riel en cas de non respect de cet avertissement Minimisez la tension d l vation AVANT de retirer l quipement fix d exp dier le chariot de stocker le chariot WWW ergotron com 826 501 Temperature Range Temperature Range Relative Humidity Range gt Storage Relative Humidity Range 5772 Operational This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada FCC Compliance Statement The cart has been tested and found to comply with the limits for a Class A
20. l temperature is 29 C 86 F The recommended humidity range for operation is 5 9596 rH recommended cart storage temperature is 15 C 59 F At this temperature the age related capacity loss is minimized The minimum storage temperature is 20 4 and the maximum storage temperature is 50 C 122 F The recommended humidity range for storage is 5 95 rH Part Number Power System 5 44 56 1 1 SV44 56T1 2 5 44 56 1 3 5 44 56 1 5 44 56 1 7 SV44 56T1 8 Input 120VAC 60 Hz 5 1 Output 120VAC 60 Hz 400VA 300W cart and power system are certified to UL 60601 and CAN CSA C22 2 60601 1 08 Input 230V 50 Hz 2 78 Output 230 50 Hz 400VA 300W cart and power system are compliant with EN 60601 1 Input 220V 60 Hz 2 7 Output 220V 60 Hz 400VA 300W 3 28 Features amp Specifications 11 8 300 mm 12 9 IMPORTANT This product will need tension adjustments once installation is complete Make sure all equipment is properly installed on the product before attempting range of motion or tension adjustments Any time equipment is added or changed on this product resulting in a different mounted weight you should repeat the adjustment steps to ensure safe and optimum operation This product should move smoothly and easily through the full range of motion and stay where you set it If movement is difficult or the product does not stay where y
21. n a Medical Electrical system connect only equipment that complies with IEC ISO UL ANSI or CSA standards that are relevant to that equipment Risk of shock or personal injury when connecting non medical equipment supplied as part of a system directly to the wall outlet when non medical equipment is intended to be supplied by the multiple socket outlet Risk of shock or personal injury when connecting any equipment that has not been supplied as part of the medical system to the multiple socket outlet 26 28 888 24 318 G 00 rev 12 14 Maintenance amp Safety Recommended Periodic Inspection and Maintenance UI Ethernet USB Inspect for wear pinching bad Monthly cables connectors Inspect for wear and debris Monthly Inspect to ensure that maximum Daily Any user recommended loads are not exceeded It is recommended that a discharge test be conducted when cart is first purchased to determine runtime with computer equipment configured on the cart Change batteries when instructed by StyleLink battery management software If StyleLink is not used it is strongly recommended that a monthly discharge test be conducted to determine runtime loss If runtime is less than 5096 of original batteries must be changed Inspect for dust at intake vacuum as required using a vacuum cleaner Power Module that DOES NOT generate ESD Monthly IT Personnel Electrostatic Discharge Batteryhamess atteryhamess for wear cracking
22. n soit fix pivot d cran se rel verait rapidement et cela pourrait b www ergotron com b Follow these instructions if you want the crossbar to pivot on the opposite side 2x E 2x 6 0 A M 2 Z 2 3 2 3 2 2 M M 4 M i So 54 lt M lt m 2 Jn amm 10 28 888 24 318 G 00 rev 12 14 2x M6 x 18mm Set up Follow these instructions if you want to lock the portrait landscape rotation feature 0 b C Attach LCDs Ax 6 M4 x 10mm M4 x 10mm d Make sure these screws are all attached 4x D M3 x 6mm 2 4 Os 888 24 318 G 00 rev 12 14 11 28 My If your monitor has recessed mounting holes you need to add the provided spacer between the monitor and the mounting plate DW M4 x 14mm 12 28 888 24 318 G 00 rev 12 14 Set up 1 2 3 Mounting Options 888 24 318 G 00 rev 12 14 13 28 Set up 1 3 To increase space and improve airflow power brick may be stored under the storage area 2x D 1 4 Plug in power cables WARNING Connecting electrical equipment to the outlet effectively leads to creating a medical system and the result can be a reduced level of safety 14 28
23. ons 888 24 318 G 00 rev 12 14 19 28 Auto Lock Drawer NOTE User should change Master Personal Identification Number PIN upon receipt of cart Ensure that the main power system batteries are installed and functioning The power does not need to be turned on at the power system user interface 1 X User PINs Without StyleLink management PINs entered on the cart and not managed by StyleLink may vary in length from 4 7 digits Lost Master PIN Ergotron recommends the following for choosing PIN digit length assumes less than 1 in 25 chance of guessing random Contact Ergotron Customer Care for User PIN instructions Max number of User PINs gt 50 5 digit length recommended Max number of User PINs 7300 6 digit length recommended For maximum security use PIN length of 7 A Carts store up to 1 000 PINs CAUTION Open only one drawer at a time Do m management Not push cart when drawers are open Failure Maximum 100 PINs per cart to follow these instructions may cause the cart 5 digit PIN length required to be unstable Set up Master PIN for the First Time Default Master PIN 12345 Contact Ergotron Customer Care for instructions if Master PIN is lost 1 Enter default Master PIN 1 2 3 4 5 then press ENTER 2 Press 5 for Master PIN Entry mode 3 Enter new Master PIN and press Enter LEDs will blink green if PIN is accepted 4 Master PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twi
24. open longer than 20 seconds Mute alarm by e Verify keypad cable is connected to controller pressing flashing button corresponding to open drawer Verify circuit breakers are not tripped and 5A fuse is installed in battery harness All available drawer numbers flashing green Waiting for drawer selection see Unlock Drawer Drawer selection not available when User PIN is entered All LEDs blink red twice PIN entry rejected exit current mode after 5 seconds timeout e Check to make sure drawer cable is installed securely All LEDs blink green 3 times PIN entry accepted e Remove power from drawer system for 10 seconds and re apply All LEDs flashing red Firmware update in progress LEDs flash red green after User PIN in entered All LEDs flashing red green System power ON or low battery condition Battery charge is low check to make sure USB charging cable is plugged into computer and computer is ON 20 28 888 24 318 G 00 rev 12 14 How to Change Fuse and Reset Circuit Breakers Turn power system off by holding down the AC Outlet Power button for 1 3 seconds Power light will shut off Disconnect Power System and Multiple Socket Outlet from 1 Turn off all mounted equipment power source Recommended Before reseting circuit breakers contact Ergotron to determine cause of trip Littelfuse 312005HXP n 0 RESET 1 lai 1 6 7 888 24 318 G 00 rev C 12 1
25. otron If you encounter problems with Cart installation or operation contact Ergotron Customer Care CAUTION DO NOT overtighten fasteners Overtightening may cause damage to your equipment A warnine Stored Energy Hazard The worksurface lift mechanism is under tension and will move up rapidly on its own as soon as attached equipment is removed For this reason DO NOT remove equipment unless the worksurface has been moved to the highest position on the tower Failure to follow this instruction may result in serious personal injury and or equipment damage When Shipping the cart set the worksurface lift mechanism to the lowest tension setting CAUTION DO NOT loosen tighten or remove any other nuts or bolts on the riser or top of tower Tampering with nuts or bolts may result in an unstable Cart leading to equipment damage and or personal injury CAUTION Release Lift Brake before moving work surface Moving work surface while Lift Brake is engaged may cause serious damage to Lift Engine A waanine In the event that repair of the StyleView Cart is needed contact Ergotron Customer Care immediately Cart repair can only be performed by Ergotron Inc or by an Ergotron authorized agent warning This cart is not intended for use in a flammable anesthetic mixture or oxygen rich environment Configuration amp Safety Additional multiple socket outlet or extension cord shall not be connected to the medical system When used i
26. ou set it follow the adjustment instructions to loosen or tighten the tension to create a smooth easy motion Depending on your product and the adjustment it may take many turns to notice a difference Weight Capacity 0165 0 kg Open Worksurface 5 165 2 3 kg Closed Worksurface 13 Ibs 5 9 kg CPU Compartment 6 10 Ibs A B 12 20 Ibs 5 4 9 1 kg 2 72 4 5 kg lt 2 165 0 9 kg lt 2 lbs 0 9 kg 25 165 11 3 kg 1 38 3 75 35 95 mm Combined LCD and CPU Compartment weight 27 Ibs 12 2 kg A CAUTION If the combined LCD and CPU weight is greater than 27 Ibs 12 2 kg then the CPU must be mounted to the rear of the cart and codec if present can be placed into the CPU compartment 4 28 888 24 318 G 00 rev 12 14 Dimensions Top View 23 8 23 8 10 15 14 63 fil 604 JopView 604 257 372 11 84 4 7 12 301 mm B ee 178 305 mm emm 1 13 41 341 mm 50 5 1283 mm 3 27 25 12 638 mm 83 mm 28 82 732 mm 13 4 3 4 340 mm 1 5 4 86 43 gt 5 31 51 390 mm mm in 3 7 787 1295 mm 95 mm 17 5 23 43 445 mm 584 1092 mm 19 75 502 mm p 6 2238 15 5 d 568 mm 13 1 75 44 mm 4 394 mm 330 mm 1 7 102 mm 1 8 3 4 Te 1 7 63 2 75 432 mm 465 mm 102
27. ower button on the Power System Interface 3 Set up the Insulation Resistance Test per the medical device safety analyzer instructions 4 Connect the Cart power cord to the medical device safety analyzer 5 Perform test 500 V 6 Ensure Insulation Resistance is greater than or equal to 1 Mohms 7 Remove medical device safety analyzer connections to Cart and return Cart to service 27 28 Maintenance amp Safety Ergotron Electromagnetic Guidance and Manufacturer s Declaration Guidance and Manufacturer s Declaration Electromagnetic Emissions The Powered Computer Cart is intended for use in the electromagnetic environment specified below The customer or the user of the Powered Computer Cart should assure that it is used in such an environment Emissions Test Compliance Electromagnetic environment guidance RF Emissions The Powered Computer Cart uses RF energy only for its CISPR 11 internal function Therefore its RF emissions are very low and unlikely to cause any interference in nearby electronic equipment RF Emissions Class A The Powered Computer Cart is suitable for use in all CISPR 11 establishments other than domestic and those directly Class A connected to the public low voltage power supply 61000 3 2 network that supplies buildings used for domestic purposes Voltage fluctuations Complies flicker emissions IEC 61000 3 3 Guidance and Manufacturer s Declaration Electromagnetic
28. p Road Eagan Minnesota 55121 USA Patents Pending and Patented U S amp Foreign Ergotron is a registered trademark of Ergotron Inc 28 28 888 24 318 G 00 rev C 12 14
29. pinching Monthy or other damage Coiled Cord Weekly Any user stretching 1 Please dispose of all batteries in accordance with local law 2 Always replace with similar size battery 33 A h to replace 33 A h and always replace in pairs Maximum Load Power System SLA IT Personnel batteries LE Replace lead acid batteries IT Personnel Earth Bond Test To ensure safety grounding between the power cord ground connection and any accessible metal parts on the cart although not mandatory the following test is recommended to be performed every two years using a calibrated medical device safety analyzer The procedure is as follows _ ADANGER Misuse Can Result in FIRE or DEATH by ELECTRICAL SHOCK LES CORDONS ELECTRIQUES PEUVENT ETRE DANGEREUX Une mauvaise utilisation peut provoquer un INCENDIE ou la MORT par CHOC 820 672 ELECTRIQUE Please Read and Follow Product Manual Instructions THIS IS A POLARIZED CORD HOSPITAL GRADE ONLY NOTE Grounding Reliability Can Only Be Achieved When the Equipment Is Connected To An Equivalent Receptacle Marked HOSPITAL ONLY Or HOSPITAL GRADE 1 Disconnect the cart from mains power unplug cart from the wall 2 Remove power from internal power system outlets by pressing the power button on the Power System Interface 3 Set up Earth Bond Test per the medical device safety analyzer instructions 4 Connect the Cart power cord to the medical device safety analyzer
30. rm Storage Ifthe Power System will be idle for 3 months or more the battery should be removed from the cart and recharged during storage WARNING Do not remove or replace the batteries while cart is located an oxygen rich or hazardous environment Sparking may occur Turn power system off by holding down the AC Outlet Power button for 1 3 seconds Power light will shut off Disconnect Power System and Multiple Socket Outlet from 1 Turn off all mounted equipment power source Caution Remove Black before removing Red Store battery in cool dry area while Cart is out of use Optimal 9 storage temperature is 15 C 59 F Battery voltage should be checked every three 3 months If voltage drops below 12 5VDC fully recharge battery Contact Ergotron Customer Care for information about how storage might impact the battery warranty 24 28 888 24 318 G 00 rev 12 14 Ergonomics Working customize to your size 1 Set top of monitor screen about one inch below eye level Release brake and lift or lower riser as needed 2 Tilt screen for comfortable viewing and to reduce eye and neck strain 3 Pull keyboard tray forward and position mouse tray on right or left as needed 4 Work with elbows bent at about 90 to minimize muscle strain 5 f the riser moves up and down with difficulty or if it drifts out of set position consult the product manual for adjustment
31. rough an electronics recycler 3 Remaining plastics and metals can be recycled through a commercial recycler Indicates an imminently hazardous situation which if not avoided will result in death or serious injury Indicates a potentially hazardous situation which if not avoided could result in death or serious injury Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury Used without the safety alert symbol indicates a potentially CAUTION hazardous situation which if not avoided may result in property damage gt INSTRUCTIONS Refer to transport instructions INSTRUCTIONS Follow operating instructions ON OFF push push NOTE Each position ON OFF is a stable position 888 24 318 G 00 rev C 12 14 25 28 Maintenance amp Safety and Maintenance The following procedures are not guaranteed to control infection The hospital infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes Ato avoid risk of electric shock do not expose electrical components to water cleaning solutions or other potentially corrosive liquids or substances Do not immerse Cart or Cart components in liquid or allow liquids to flow into the Cart Wipe all cleaners off surface immediately using a damp cloth Thoroughly dry surface after cleaning Av not use flammable cleaners on Cart surfaces due to clos
32. tact Ergotron Customer Care for more information casters Check casters periodically to make sure they are clean and free of debris that would prevent smooth travel Avoid moving Cart across uneven dirty or damaged surfaces customer Equipment Make sure equipment is balanced and mounted securely to Cart Do not reposition Cart components on riser or tower unless instructed to do so in the installation instructions Moving Cart components too high or too low on the Riser may create an unstable condition leading to equipment damage or even personal injury Contact Ergotron Customer Care for information about moving Cart components Safety Alerts Associated with this Product The following Warnings Cautions appear in this reference guide or on the cart NOTE Failure to adhere to these guidelines may result in equipment damage or personal injury caution The lift brake helps stablilize the worksurface and keyboard tray during normal use but it DOES NOT increase load capacity DO NOT load riser with equipment totaling more than the maximum weight capacity specified by Ergotron Ensure optimum lift function by testing and if necessary re adjusting tension whenever the weight mounted to the riser changes i e equipment is removed or added See Set Riser Lift Tension adjustment instructions caution Do not operate StyleView Cart with missing or damaged components Do not remove modify or substitute Cart components without consulting Erg
Download Pdf Manuals
Related Search