Da-Lite Large Advantage Deluxe Electrol 222"
Contents
1. INSTRUCTION BOOK FOR Large Advantage Deluxe Electrol DA LITE Important Safety Instructions When using your video equipment basic safety precautions should always be followed including the following 1 Read and understand all instructions before using Close supervision is necessary when any appliance is used by or near children Do not leave appliance unattended while in use Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged until it has been examined by a qualified serviceman Position the cord so that it will not be tripped over pulled or contact hot surfaces If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 6 To reduce the risk of electric shock do not immerse this appliance in water or other liquids To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric Shock when the appliance is used subsequently The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons Save These Instructions Tools Required for Installation 2 Phillips Screwdriver 3 4 Open Wrench or Socket Driver Pre Installation Carefully unpack case f2. by raising picture surface approximately two feet then lower again Repeat until desired picture surface position is attained A CAUTION Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller This screen comes standard with O or 2 black at the top See the specification data sheet for details A ATTENTION N effectuez pas de r glage pour obtenir un d roulement sup rieur a celui command Au moins 1 1 2 tour de toile doit tre maintenu sur le cylindre Cet cran est dot de s rie d une bande noire sup rieure de O cm O po ou 5 cm 2 po Consultez la fiche technique pour plus de renseignements Less Screen Drop 1 Raise picture surface approximately two feet above desired level Place operating switch in off position Turn the white down limit switch Fig 2 one quarter turn clockwise Test by raising picture surface approximately two feet then lower again Repeat until desired picture surface position is attained Contact Da Lite at 800 622 3737 if door motor needs adjustment 120V Wiring Diagram NOTE 20 24 AWG wire recommended for connecting wall switch to dual motor controller A CAUTION Do not use 3 position high voltage rocker switch with this unit This will damage the low voltage control board A ATTENTION N utilisez pas un interrupteur bascule 3 positions pour circuit haute tension avec cette unit Cela endommagera
3. le tableau de contr le basse tension Front of Back of Wall Wall Switch Switch White Common Red Red U U Eye Port ee Up Beer Plug IR or RF Dawn Remote Here White Common Not Used iw Common O o Power Input l AL i 120VAC 60HZ B EN o B 1 Ee aa White Dual Motor Control Board Green Ground 240V Wiring Diagram NOTE 20 24 AWG wire recommended for connecting wall switch to dual motor controller CAUTION Do not use 3 position high voltage rocker switch with this unit This will damage the low voltage control board A ATTENTION N utilisez pas un interrupteur a bascule 3 positions pour circuit haute tension avec cette unit Cela endommagera le tableau de contr le basse tension Front of Back of Wall Wall Switch Switch cag Blue Il Common He a Eye Port we Up Plug IR or RF Black Remote Here Down White Common Een Wo Not Used Sis CEREN Power Input 240VAC 50HZ Dual Motor Control Board Green Yellow Ground Green j Yellow Ground Troubleshooting Visit www da lite com to find installation and troubleshooting tutorials You will also find a link to Live Chat for interactive support Symptom Screen will not operate or will not go down Motor does not hum Motor hums Screen will not move upward Motor does not hum Motor hums You can contact us by email at i
4. EU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also Nave other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 8006223737 F 574 267 7804 or 877 325 4832 E info da lite com www da lite com DL 0171 Rev 3 12 14 2014 Milestone AV Technologies LLC Printed in U S A 35895
5. er and secure with 2 screws NOTE Motor Operator Projection Screen Models LADT LADDT LAD and LADD must be installed in accordance with the requirements of the Local Building Codes the Canadian Electrical Code CEC CAN CSA C221 and the National Electric Code NEC NFPA 70 An appropriate disconnect device shall be provided as part of the building installation 4 If your case was ordered in advance of the screen and roller assembly your installation is now complete Continue to step 4 if your Large Advantage Deluxe Electrol was ordered as a complete unit Carefully remove paper and tape from roller assembly A Caution Do not use a knife or sharp object to cut tape you will damage the screen Pull orange string ATTENTION Ne coupez pas le ruban adh sif sur la toile avec un couteau ou un outil tranchant Tirez sur le cordon orange Test installation by running screen up and down a few times Be prepared to stop screen should any objects obstruct the movement of the screen To prevent damage to the motor the standard duty cycle is 1 minute on and 3 minutes off Installation Suggested 1 4 Threaded Rod Not Included Attached To Mounting Bracket Finished Self Trimming Ceiling Flange 2 lt gt Variable Position Mounting Brackets Electrical Junction Box Screen Roller Audience Side Door Roller SE REECE TS ESE LLH ELU LL Zo D e O Access Doo
6. ity fuse Reset facility circuit breaker Check above Tighten all loose wire connections See above Replace low voltage board Up Position Check for power across red and White leads Replace switch Let motor cool down for 15 minutes Try again Check for continuity Replace motor assembly NOTE Motor is a sealed assembly Replace motor assembly Troubleshooting continued Symptom Cause Solution Spring has an obstruction not Check installation to free door Clear any foreign allowing door to open substance from spring Door will not open No power See above Mis adjusted door motor limit Adjust door motor limit Call Da Lite for instruction Door does not close Low voltage board has no power or a blown transformer Down limit switch incorrect Down limit switch out of adjustment See installation instructions Noise Buzzing noise Adjust door limit switch too far down Replace low voltage board NOTE Screen will operate with a low pitched hum Gear noise Replace motor assembly Normal condition Fabric rubbing NOTE Screens with ironing boards have fabric that drags across the board Defective brake Replace motor assembly Roller displaced from mounting bracket Pin end slipped out of nylon bearing Realign pin end bracket Screen not installed properly Check for level and plumb Fabric hangs crooked Fabric is damaged Replace fabric Door closes befo
7. nfo da lite com or by phone at 800 622 3737 or 574 267 8101 with any additional troubleshooting questions Cause Incorrect line voltage Blown facility fuse Tripped facility circuit breaker No power to operating switch or junction box Low voltage board has no power or blown transformer Power at junction box Thermal overload tripped Broken wire in the down position Defective motor limit switch or capacitor Capacitor burned out Incorrect line voltage Blown facility fuse Tripped facility circuit breaker No power to operating switch or junction box Low voltage board has no power or blown transformer Open door limit switch Power at junction box Thermal overload tripped Broken wire in the Up position Defective motor limit switch or capacitor Capacitor burned out Solution Verify 115 125V or 220 240V If insufficient voltage rewire incoming electric line Replace facility fuse Reset facility circuit breaker Check above Tighten all loose wire connections Recheck wiring See installation instructions Replace low voltage board Down Position Check for power across black and white leads Let motor cool down for 15 minutes Try again Check for continuity Replace motor assembly NOTE Motor is a sealed assembly Replace motor assembly Verify 115 125V or 220 240V If insufficient voltage rewire incoming electric line Replace facil
8. r Closing Door 2 Nie 10 A gt Self Trimming Flange Screen And Roller Assembly Installation If your screen was shipped with the motor and roller already installed proceed to step 7 i Remove four bolts from ends of door assembly 2 bolts on each end Fig 2 This will allow the door assembly to drop open for access to case For larger sizes you will also need to remove the door support screws Carefully unpack screen and roller assembly Leave packing paper on the roller Remove the square peg bracket from the motor end ofthe roller assembly Remove the safety clip from the motor attachement bracket located in the motor end of the screen housing Place the roller assembly into the case with the motor on the left side The limit switches should be facing down Line up the head of the motor With the motor attachment bracket Loosen four bolts that secure pin end mounting bracket into housing Lift pin end of roller into position and slide the bracket into the roller pin Tighten all four bolts Complete electrical hook up by snapping motor 1 3 wire connectors into case connectors Door Support Screws Not All Sizes Access Door Figure 2 8 Return to motor end and insert safety clip over casting bracket to secure motor end A CAUTION Do not cut tape on fabric with a knife or any sharp tool Remove by hand ATTENTION Ne coupez pas le ruban adh sif sur la toile Dual Motor LVC Con
9. re screen is all the way up Screen up limit out of adjustment Adjust up limit call factory for instructions Door opens but screen does not Loose wire Check all wiring and connections operate LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da Lite branded products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LI
10. rom shipping crate 2 Set aside the Installation Kit Items inside will be used during installation 3 Make sure to recheck measurement of case for proper installation clearance 4 Remove any protective foam from case Board Ironing 5 If necessary adjust hanger brackets with a 3 4 open wrench or socket driver Ironing Board The Large Advantage Electrol includes an ironing board to flatten the fabric long strip attached The ironing board is part of the screen case Do not remove Contact Da Lite if the ironing board is in need of adjustment Figure 1 Figure 1 Case Installation The case has a self trimming flange around the bottom Ceiling tiles or drywall may be placed on top of this flange to provide a finished appearance 1 The case provides multiple attachment points for bolts cables or threaded rod Page 5 shows threaded rod installed The variable position mounting bracket may be located anywhere along the length of the case It is recommended to keep the brackets spaced evenly enough to distribute the weight of the screen One mounting bracket is required for every 4 of case length Tighten bolts until trim flange is flush with ceiling NOTE For proper operation screen assembly must be level after installation Remove 2 screws to open junction box Install electrical connections that apply to your unit Make sure to review the wiring diagram for proper hook up Replace junction box cov
11. trol Box Screen Motor Limit Switches avec un couteau ou un outil tranchant Retirez la main Carefully remove tape strips securing picture surface around roller Slat should move freely Fig 3 Only if the roller assembly is pre installed Test installation by operating the screen several times Be prepared to stop the screen The door assembly will not close until the wall switch is placed in the up position and when the screen motor stops at its limit switch in the up direction NOTE Unit duty cycle is 1 minute on 3 minutes off NOTE Excessive continuous operation may cause the motor to overheat If this happens the motor will shut off until it cools to a normal operating temperature Close door assembly and replace four bolts at ends of door 2 bolts on each end Fig 2 Door Motor Limit Switches Access Door Assembly Door Motor Screen Motor Figure 3 Screen Adjustment Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da Lite Should it be necessary to adjust for more or less drop of picture proceed in the following manner NOTE Use a screw driver or 5 32 Allen wrench to make adjustments More Screen Drop Place operating switch in down position 2 When the screen stops turn the white down limit knob Fig 3 one quarter turn counterclockwise Test
Download Pdf Manuals
Related Search