ONKYO LS-T30
Contents
1. Safety Limits and methods of measurement of radio disturbance characteristics Limits for harmonic current emissions Limitation of voltage changes voltage fluctuations and flicker RoHS Directive 2011 65 EU Hereby Onkyo Corporation declares that this LS T30 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Speaker Precautions Placement e The subwoofer cabinet is made out of wood and is therefore sensitive to extreme temperatures and humidity do not put it in locations subject to direct sunlight or in humid places such as near an air conditioner humidifier bathroom or kitchen Do not put water or other liquids close to the speakers If liquid is spilled over the speakers the drive units may be damaged Speakers should only be placed on sturdy flat surfaces that are free from vibration Putting them on uneven or unstable surfaces where they may fall and cause damage will affect the sound quality Safety precautions e Subwoofer is designed to be used in the upright vertical position only Do not use it in the horizontal or tilted position e Ifthe unit is used near a turntable CD player or DVD player howling or slipping of sound may occur To prevent this move the unit away from the turntable CD player or DVD player otherwise lower the unit s output level Use with a TV set In general Braun tubes used for color television sets etc are extremely se2. time remove the insulation sheet Use a CR2025 lithium coin battery for battery replacement Positive side sA e 3h P ra d r Remote control sensor Approx 5m 16 ft Placement The illustration shows an example of placement Mount the unit on a firm surface such as the top of a low board Also subwoofer is located on the bottom side of the unit Please take extra care on setting TVs meeting the following requirements may be placed on the unit e Weight 60 kg 132 2 Ibs or less e Width of TV stand 900 mm 35 7 16 or less e Depth 360 mm 14 3 16 or less Mountable area 1 2 Affix the cushioning pads to the bottom of the TV stand Using the supplied cushions will allow you to limit the effect of vibrations on the TV Wrap the TV in a blanket or soft cloth to avoid damage during installation Installation should be performed by at least two people When the supplied cushions and the feet of the TV do not match cut and shape the cushions for use as needed Place the unit on top of the low board The unit is extremely heavy Be very careful not to trap your fingers when mounting it Mount the TV so that it does not protrude from the top face of the unit If the TV stand protrudes from the top face of the unit the TV may tip over and cause injury Also for TV tip over fall prevention measur
3. 785 2650 http Awww us onkyo com For Product Support Team Only 1 800 229 1687 http Awww us onkyo com Europe Onkyo Europe Electronics GmbH Liegnitzerstrasse 6 82194 Groebenzell GERMANY Tel 49 8142 4401 0 Fax 49 8142 4208 213 http Awww eu onkyo com Onkyo Europe Electronics GmbH UK Branch Meridien House Ground floor 69 71 Clarendon Road Watford Hertfordshire WD17 1DS United Kingdom Tel 44 0 8712 00 19 96 Fax 44 0 8712 00 19 95 China Onkyo China Limited Hong Kong Unit 1033 10 F Star House No 3 Salisbury Road Tsim Sha Tsui Kowloon Hong Kong Tel 852 2429 3118 Fax 852 2428 9039 http www hk onkyo com Onkyo China PRC Mainland 1301 555 Tower No 555 West NanJing Road Jing an District Shanghai China 200041 Tel 86 21 52131366 Fax 86 21 52130396 http Awww cn onkyo com Asia Oceania Middle East Africa Please contact an Onkyo distributor referring to Onkyo SUPPORT site http www intl onkyo com support The above mentioned information is subject to change without prior notice Visit the Onkyo web site for the latest update F1408 0 SN29401856 C Copyright 2014 Onkyo Corporation Japan All rights reserved 29 40418 5 6
4. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Industry Canada licenceexempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device This transmitter must not be co located or operated in conjunction with any other antenna or transmitter RF Exposure Compliance This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency RF Exposure Guidelines in Supplement C to OET65 and RSS 102 of the IC radio frequency RF Exposure rules This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation MPE But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person s body excluding extremities hands wrists feet and ankles For Canadian Models NOTE CAN ICES 3 B NMB 3 B For models having a power cord with a polarized plug CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following
5. operate the unit during this time Afterwards it will flash 3 times to indicate that this feature has been cancelled Perform the same procedures to use the TV remote controller again The mute state can be turned over each time you press the Mute button on your TV remote controller In such case you can synchronize the mute status of the unit and the TV by pressing and holding the Mute button on your TV remote controller Learning function The unit is set so that signals emitted from each button on your TV remote controller control specific operations Itis recommended to select buttons that do not prevent TV operation when assigning the functions to your remote controller Signal of some types of remote controller may not be received by the unit E g To assign the unit s ON STANDBY function to the TV remote controller 1 Press the button on the unit for approximately 3 seconds while pressing and holding the button The input source indicator white flashes for 10 seconds 2 While the input source indicator is flashing press any button on the TV remote controller 3 times while aiming it at the remote control signal sensor of the unit The indicator flashes twice white to indicate that this was successfully configured After this is set pressing the button on the TV remote controller will enable ON STANDBY operation on the unit The learning function enables the following unit functions to be operated w
6. requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Hiermit erkl rt Onkyo Corporation dass sich das Ger t LS T30 in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschl gigen Bestimmungen der Richtlinie 1999 5 EG befindet Hierbij verklaart Onkyo Corporation dat het toestel LS T30 in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG H rmed f rklarar Onkyo Corporation att denna LS T30 f ljer de v sentliga kraven och andra relevanta stadgar i Direktiv 1999 5 EC C HactoaeTo Onkyo Corporation aexnapupa ye LS T30 e B CbOTBETCTBNE CbC CbLECTBEHMTe N3MCKBAHMA V ApyrMTenpunoxumn pa3snopen6u Ha upextusa 1999 5 EC Onkyo Corporation t mto prohla uje Ze LS T30 spl uje z kladn po adavky a v echna p slu n ustanoveni Sm rnice 1999 5 ES Undertegnede Onkyo Corporation erkl rer herved at f lgende udstyr LS T30 overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF K esolevaga kinnitab Onkyo Corporation seadme LS T30 vastavust direktiivi 1999 5 EU p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele ME THN MAPOYZA O KATAZKEYAZTHE Onkyo Corporation AHAQNEI OTI LS T30 ZYMMOPQQNETAI NPOZ TIZ OYZIQAEIZ ANAITHZEIZ KAI TIZ AOINES ZXETIKEX AIATAZEIZ THE OAHMAZ 1999 5 EK Ar o Onkyo Corporation deklar ka LS T30 atbilst Direkt vas 19
7. 99 5 EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem iuo Onkyo Corporation deklaruoja kad is LS T30 atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas A Onkyo Corporation ezzennel kijelenti hogy a LS T30 t pus beren dez s teljes ti az alapvet k vetelm nyeket s m s 1999 5 EK ir nyelvben meghat rozott vonatkoz rendelkez seket Niniejszym Onkyo Corporation deklaruje e LS T30 jest zgodny z zasadniczymi wymaganiami i innymi w a ciwymi postanowieniami Dyrektywy 1999 5 EC Eu Onkyo Corporation declaro que o LS T30 cumpre os requisitos essenciais e outras provis es relevantes da Directiva 1999 5 EC Prin prezenta Onkyo Corporation declar c aparatul LS T30 este n conformitate cu cerin ele esen iale i cu alte prevederi pertinente ale Directivei 1999 5 CE Onkyo Corporation t mto vyhlasuje Ze LS T30 a spliia z kladn po iadavky a v etky pr slu n ustanovenia Smemice 1999 5 ES Onkyo Corporation izjavlja da je ta LS T30 v skladu z bistvenimi zahtevami in drugimi relevantnimi dolo ili direktive 1999 5 ES Onkyo Corporation vakuuttaa t ten ett LS T30 tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen H r me l sir Onkyo Corporation v yfir a varan LS T30 er samr mi vi grunnkr fur og a rar kr fur sem ger ar eru tilskipun 1999 5 EC Onkyo Corporation e
8. ON CAREFULLY AC outlet voltages vary from country to country Make sure that the voltage in your area meets the voltage requirements printed on the unit s rear panel e g AC 230 V 50 Hz or AC 120 V 60 Hz The power cord plug is used to disconnect this unit from the AC power source Make sure that the plug is readily operable easily accessible at all times For models with POWER button or with both POWER and ON STANDBY buttons Pressing the POWER button to select OFF mode does not fully disconnect from the mains If you do not intend to use the unit for an extended period remove the power cord from the AC outlet For models with ON STANDBY button only Pressing the ON STANDBY button to select Standby mode does not fully disconnect from the mains If you do not intend to use the unit for an extended period remove the power cord from the AC outlet Preventing Hearing Loss Caution Excessive sound pressure from earphones and headphones can cause hearing loss Batteries and Heat Exposure Warning Batteries battery pack or batteries installed shall not be exposed to excessive heat as sunshine fire or the like Never Touch this Unit with Wet Hands Never handle this unit or its power cord while your hands are wet or damp If water or any other liquid gets inside this unit have it checked by your Onkyo dealer Handling Notes e If you need to transport this unit use the original packaging to pack it how
9. ONKYO LS 30 TV Speaker System Instruction Manual Thank you for purchasing an Onkyo product Please read this manual thoroughly before making connections and plugging in your new Onkyo product Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new product Please retain this manual for future reference Control Reference Guide 4 Placement e ceeteeeeeeeteeeeees 7 Connecting to a TV 008 8 Listening to TV cceeeeees 9 Using a TV Remote Controller 11 Playing via Bluetooth Connection 12 Troubleshooting 13 Supplied Accessories 15 Safety precautions WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING AVIS RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE DO NOT OPEN NEPAS OUVRIR The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is inte
10. OPTICAL 1 COAXIAL 1 North American USB 1 Analog Stereo Input 3 5 mm mini Bluetooth Version 2 1 EDR Profile A2DP GAVDP Speaker unit None magnetic shielding Front speaker 6 5 cm 2 1 2 Cone x4 Subwoofer 16 cm 6 1 2 Cone x1 e Design and specifications are subject to change without notice Playing USB Memory North American models e The unit supports USB memory formatted using FAT12 FAT16 and FAT32 file system The unit is compatible with WAV playback and following audio format is supported Format Microsoft PCM format Number of channels 1 or 2 channels Sampling frequency 32 to 48 kHz Quantization bit width 8 or 16 bit depth RIFF chunk format chunk without extended data chunk You can play WAV files stored on the root folder only WAV files stored on the other folders cannot be played on this unit The unit supports USB flash drives only Note however that playback may not be possible with some USB flash drives Disclaimer e The unit contains a microcomputer for signal processing and control functions In very rare situations severe interference noise from an external source or static electricity may cause it to lock up In the unlikely event that this happens unplug the power cord from the wall outlet wait at least five minutes and then plug it back in If it doesn t work properly please try resetting E Trademarks and Licensing DOLBY DIGITAL Manufactured
11. Unplug this apparatus won unused Yor long Ohe periods of time SNA 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions When the power supply cord or plug is damaged B If liquid has been spilled or objects have fallen into the apparatus C Ifthe apparatus has been exposed to rain or water D Ifthe apparatus does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation E If the apparatus has been dropped or damaged in any way and F When the apparatus exhibits a distinct change in performance this indicates a need for service 16 Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short out parts that NOORWON gt 17 18 could result in a fire
12. e s no obstruction between the remote controller and the unit s remote control sensor Make sure that the unit is not subjected to direct sunshine or inverter type fluorescent lights Relocate if necessary If the remote controller does not work the first time after purchase or if it has not been used for a long period of time the battery may have become flat and the remote controller will not operate Try the following methods Press and hold the VOLUME button on the remote controller for some time 10 seconds or more try this several times Remove the button cell wipe it with a clean cloth and insert it again Specifications Rated Output Power FTC Front speaker North American 12 5 W minimum continuous power per channel 4 ohm loads 2 channel driven at 1 kHz with a maximum total harmonic distortion of 1 Subwoofer North American 25 W minimum continuous power 4 ohm loads 1 channel driven at 80 Hz with a maximum total harmonic distortion of 1 Rated Output Power IEC Front speaker Others 2chx 12 5 W at 4 ohms 1 kHz 1ch driven of 1 Subwoofer Others 1chx 25 W at 4 ohms 80 Hz 1ch driven of 1 Frequency response 20 Hz 20 kHz Power Supply AC100 240 V 50 60 Hz Power Consumption 17W Stand by Power Consumption North American 0 40 W Others 0 45 W Dimensions WxHxD 905 mmx95 mmx 400 mm 35 5 8 X 3 3 4 x 15 3 4 Weight 10 4 kg 22 9 Ibs Audio inputs Digital input
13. es see the TV owner s manual If the unit vibrates after placement mount the supplied vibration prevention cushions under the feet of this unit and adjust so that it does not vibrate Onkyo is not responsible for accidents or damage caused by improper installation improper cushion attachment improper use or natural calamity etc Connecting to a TV OPTICAL OUT If there is the OPTICAL jack on the TV being used illustrated above Make a digital connection to the TV with the supplied optical digital audio cable Connect the AC adapter power cord into the DC IN on the unit and then connect the other end of the power cord into an electrical outlet Important Depending on the TV to be used with this unit the sound coming through the TV s built in speakers can be out of sync with the sound coming through the unit Be sure to turn off the built in speaker output on your TV before using the unit Perform the same procedure when also making connections using the stereo mini plug cable or coaxial cable mego If there is no OPTICAL jack on the TV being used Connect either of the following E Make an analogue connection with the TV using the supplied stereo mini plug cable ANALOG aii OUT TV E Make a digital connection to the TV using a coaxial cable sold separately COAXIAL OUT TV COAXIAL nO Listening to TV Basic operations 1 Turn on the TV Auto Power On i
14. h other devices on the Bluetooth enabled device 1 Press 5 to turn on the unit 2 Press to switch the selector to Bluetooth ON STANDBY INPUT BLUETOOTH Q The unit begins pairing and the input source indicator on the unit will flash quickly blue The pairing mode will be cancelled after 30 seconds During this time perform the following operation The indicators will flash slowly indicating that this has been cancelled 3 Select the unit Onkyo LS T30 after it displays on the screen on the Bluetooth device After a short time the input source indicator will light blue and the devices are now paired e If a passcode password passkey or PIN code is requested enter 0000 e Devices should be in close proximity when pairing 33 ft Playing sound of the Bluetooth enabled device 1 Press 5 to turn on the unit 2 Press to switch the selector to Bluetooth The input source switches to Bluetooth and the input source indicator lights in blue 3 Play music files by after connecting the Bluetooth device e If the volume setting on the Bluetooth enabled device is low the sound will not be output from this unit Due to the characteristics of Bluetooth wireless technology the sound produced on this unit may slightly be behind the sound played on the Bluetooth enabled device To register other Bluetooth devices Turn on the power to the unit switch the input to Blueto
15. ied optical digital audio cable are used depending on the audio outputs available on your TV COAXIAL jack Makes a digital connection to the TV using a coaxial cable sold separately USB port North American models Connects a USB flash memory Others This port is used for service purposes only Do not use it ANALOG jack Makes an analogue connection with the TV using the supplied stereo mini plug cable DC IN terminal Connects the supplied AC adapter ON STANDBY SOUND MODE INPUT USB BLUETOOTH i ese VOLUME MUTING NS olo SUBWOOFER i 9e ONKYO RC 894S North American models Remote controller d Control Reference Guide INPUT BLUETOOTH SUBWOOFER Others This manual outlines procedures using the remote controller ON STANDBY button Switches the power on standby SUBWOOFER buttons Adjust the subwoofer level SOUND MODE button Use this button to select the desired sound mode for the playback audio INPUT buttons Switches the input source VOLUME buttons MUTING button USB operation buttons North American models Allows operation when the input source is USB plays or pauses playback return to the start of the file being played Press twice to return to the previous file skip to the next file When using the remote controller for the first
16. it was when you originally bought it e Do not leave rubber or plastic items on this unit for a long time because they may leave marks on the case e This unit s top and rear panels may get warm after prolonged use This is normal e Ifyou do not use this unit for a long time it may not work properly the next time you turn it on so be sure to use it occasionally For U S and Canadian models FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver
17. ith your TV remote controller Press and hold the following buttons instead of in step 1 VOLUME VOLUME MUTING and INPUT and SOUND MODE and To prevent incorrect operation The unit is preprogrammed to support a large number of TV remote controllers For this reason using remote controllers other than that supplied with the unit and TV remote controllers may result in unexpected operation To prevent incorrect operation press and hold on the unit and then press and hold while continuing to press for 3 seconds The input source indicator will flash white for 10 seconds During this time aim the TV remote controller toward the unit and press either the volume button or mute button once The input source indicator will flash twice white which indicates that the unit will not accept signals emitted when buttons are pressed on remote controllers other than the supplied remote controller or the TV remote controller e Controlling function may not be set to some TV remote controller Playing via Bluetooth Connection You can wirelessly enjoy music files stored ina smartphone or other Bluetooth enabled device The coverage area is 10 meters 33 feet Pairing Approx 10 m Pairing is necessary when using the Bluetooth enabled device for the first time Before starting the procedure learn how to enable the Bluetooth setting function and to connect wit
18. ly Check that all cables are connected and that the input source is correct and leave the power cord unplugged for 5 minutes Plug the power cord in again and turn the unit power on If the sound still cuts out unplug the power cord and contact your Onkyo dealer e If smoke smell or abnormal noise is produced by the unit unplug the power cord from the wall outlet immediately and contact your Onkyo dealer There s no sound or it s too small Make sure that all audio connecting plugs are pushed in all the way e Make sure that the input of device is connected properly e When the status indicator flashes in white the muting is enabled Press MUTING button on the remote controller or the VOLUME buttons on the remote controller or the unit to disable the muting e Make sure that none of the connecting cables are bent twisted or damaged Audio is output through only one type of connection When multiple terminals are in use the priority of audio output is given in the order of the OPTICAL terminal COAXIAL terminal and ANALOG terminal Noise can be heard e Do not bind the power cord connection cables and other audio cables with a band e An audio cable may be picking up interference Try repositioning your cables The remote controller doesn t work e Make sure that the battery is installed with the correct polarity Make sure that the remote controller is not too far away from the unit and that ther
19. nded to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or PORTABLE CART WARNING table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13
20. ning to TV Auto Standby function If there is no audio input and no operation of the unit has been performed for some time the power will automatically enter standby mode as Auto Standby is on by default The time taken to enter standby mode depends on the connected cables or the input source e Connecting with the optical digital audio cable or coaxial cable 2 hours 5 minutes when power to the TV is off e Connecting with the stereo mini plug cable 5 minutes Bluetooth USB North American models 5 minutes To cancel this function press and hold on the unit and then press and hold while continuing to press The input source indicator flashes twice white to indicate that this setting is now off e Repeating this procedure switches between on off The indicator flashes once to indicate that this setting is now on Using a TV Remote Controller Preprogrammed feature The unit has been preprogrammed so that the unit can be operated using your TV remote controller Volume control and muting operations can be performed with this feature If you want to use other functions or cannot operate the unit with your TV remote controller you can use the learning function described below to enable these features To cancel this feature press and hold for approximately 3 seconds while continuing to press and hold on this unit The input source indicator will flash white for 10 seconds Do not
21. nsitive and can be affected even by the magnetism of the earth If a speaker system is used near them therefore discoloring or distortion of pictures will occur These speakers are not provided with magnetic shielding If discoloration or distortion occurs move the speakers apart from the television set Input Signal Warning The speakers can handle the specified input power when used for normal music reproduction If any of the following signals are fed to them even if the input power is within the specified rating excessive current may flow in the speaker coils causing burning or wire breakage 1 Interstation noise from an untuned FM radio 2 Sound from fast forwarding a cassette tape 3 High pitched sounds generated by an oscillator electronic musical instrument and so on 4 Amplifier oscillation 5 Special test tones from audio test CDs and so on 6 Thumps and clicks caused by connecting or disconnecting audio cables Always turn off your amplifier before connecting or disconnecting cables 7 Microphone feedback CE Par la pr sente Onkyo Corporation d clare que l appareil LS T30 est conforme aux exigencies essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Por la presente Onkyo Corporation declara que este LS T30 cumple con los requisites esenciales y otras exigencias relevantes de la Directiva 1999 5 EC Con la presente Onkyo Corporation dichiara che questo LS T30 conforme ai
22. or electric shock The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Don t put candles or other burning objects on top of this unit Batteries Always consider the environmental issues and follow local regulations when disposing of batteries If you install the apparatus in a built in installation such as a bookcase or rack ensure that there is adequate ventilation Leave 20 cm 8 of free space at the top and sides and 10 cm 4 at the rear The rear edge of the shelf or board above the apparatus shall be set 10 cm 4 away from the rear panel or wall creating a flue like gap for warm air to escape Precautions 4 Recording Copyright Unless it s for personal use only recording copyrighted material is illegal without the permission of the copyright holder AC Fuse The AC fuse inside the unit is not user serviceable If you cannot turn on the unit contact your Onkyo dealer Care Occasionally you should dust the unit all over with a soft cloth For stubborn stains use a soft cloth dampened with a weak solution of mild detergent and water Dry the unit immediately afterwards with a clean cloth Don t use abrasive cloths thinners alcohol or other chemical solvents because they may damage the finish or remove the panel lettering Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME READ THE FOLLOWING SECTI
23. oth and then press and hold 8 to start pairing on the unit Next select the unit Onkyo LS T30 on some other Bluetooth device to make a connection e Up to 16 Bluetooth devices can be saved with the unit e When using buttons on the unit press and hold Troubleshooting Before starting the procedure Problems may be solved by simply turning the power on off or disconnecting connecting the power cord which is easier than working on the connection setting and operating procedure Try the simple measures on both the unit and the connected device Resetting the unit Resetting the unit to the status at the time of shipment may solve the problem Reset the unit with the following procedure Press and hold the button on the unit when the power is on and then press and hold while continuing to press for 10 seconds When reset is complete the INPUT source indicator and all status indicators light and the unit automatically enters the standby mode Can t turn on the unit e Make sure that the power cord is properly plugged into the wall outlet e Unplug the power cord from the wall outlet wait 10 seconds or more then plug it in again The unit turns off unexpectedly e The unit will automatically enter standby mode when Auto Standby launches The sound stops suddenly or stops during playback e The protective circuits of the unit may be operating Unplug the power cord from the wall outlet immediate
24. rkl rer herved at denne LS T30 er i overensstemmelse med vesentlige krav og andre relevante bestemmelser l direktiv 1999 5 EC Ovime Onkyo Corporation potvr uje da je LS T30 u suglasnosti sa osnovnim zahtjevima i ostalim relevantnim odredbama Direktive 1999 5 EC Control Reference Guide 2 Main unit INPUT button Switches the input source Each time the button is pressed input modes are switched in order of TV gt USB North American models gt Bluetooth gt Also switches the power on standby Press and hold for approximately 3 seconds to place the device into Standby Press once to turn the power on OVOLUME buttons SOUND MODE button Use this button to select the desired sound mode for the playback audio P10 Dolby indicator Lights when the digital audio input signal is Dolby Digital Left channel speaker Input source indicator Lights in accordance with the input source The indicator lights in white for TV yellow for USB North American models and blue for Bluetooth Status indicators Displays the sound mode volume and subwoofer level Right channel speaker Bottom of the unit Subwoofer Plays sub bass frequencies Control Reference Guide DC IN T AUDIO IN 24V 2 7A OPTICAL COAXIAL oeo Rear of the unit terminals OPTICAL jack Makes a digital connection to the TV with the suppl
25. s turned on by default and so power to the unit turns on automatically The input source automatically switches to TV and audio from the TV is played e The input source switches to TV and the input source indicator lights in white To cancel Auto Power On press and hold on the unit and then press and hold G while continuing to press The input source indicator flashes twice white to indicate that this setting is now off e Repeating this procedure switches between on off The indicator flashes once to indicate that this setting is now on e When this setting is off press C to turn on the power to the unit and then press to switch the input source to TV To adjust the volume of this unit Allows to adjust the volume by 1 step in the 0 to 35 range 1 Press VOLUME VOLUME 4 AN The status indicators white indicate the volume level o o o e e Volume Middle To adjust the subwoofer level Allows to adjust the subwoofer level by 1 step in the 10 to 10 range while listening to the sound The default setting is 0 Also the subwoofer level is set to individual levels for each different SOUND MODE 1 Press SUBWOOFER SUBWOOFER The status indicators white indicate the subwoofer level e e fe 9 Volume Standard To mute the sound 1 Press MUTING MUTING The status indicator flashes when the audio is muted Press again
26. to cancel muting Muting will also be canceled when the volume is changed or the power is turned off and on When using buttons on the unit press and atthe same time Press again to cancel muting Change the desired sound quality SOUND MODE You can switch the sound mode of input sound as desired 1 Press SOUND MODE button The sound modes are switched in the following order each time this button is pressed The status indicator lights orange indicate the current mode e oO O O e Standard Play files with a good balance from low through to high frequencies This is the standard mode with neutral settings o o o o o Surround Creates a richer sound field provides realistic sound movement and amplifies bass sounds Ideal for watching movies oOo O Stereo Suitable for listening to music Playback music with pure quality similar to the original sound 9 e o o e Voice Play files with voice clearly Ideal when watching the news or documentary programmes Switch audio in sound multiplex programmes This can be set only when the audio signal is Dolby Digital Press and hold the SOUND MODE button on the remote controller for approximately 3 seconds Pressing and holding switches the source in the following order Main The input indicator white flashes once Secondary The input indicator white flashes twice Main Secondary The input indicator white flashes three times Liste
27. two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device For British models Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel IMPORTANT The wires in the mains lead are coloured in accordance with the following code Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red IMPORTANT The plug is fitted with an appropriate fuse If the fuse needs to be replaced the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug Check for the ASTA mark or the BSI mark on the body of the fuse If the power cord s plug is not suitable for your socket outlets cut it off and fit a suitable plug Fit a suitable fuse in the plug For European Models WEEE http www onkyo com manual weee weee pdf Declaration of Conformity We declare under our sole responsibility that this product complies with the standards
28. under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories S dts Studio Sound For DTS patents see http patents dts com Manufactured under license from DTS Licensing Limited DTS the Symbol amp DTS and the Symbol together are registered trademarks and DTS Studio Sound is a trademark of DTS Inc C DTS Inc All Rights Reserved Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Onkyo is under license Other trademarks and trade names are those of their respective owners Supplied Accessories Make sure you have the following items before use The number in parenthesis indicates the quantity e In catalogs and on packaging the letter at the end of the product name indicates the color AC adapter 1 Power cord 1 Remote controller 1 RC 894S North American models RC 895S Others Optical digital audio cable 1 5 m 5 ft 1 3 5 mm stereo mini plug cable 1 Cushion 8 attach to the bottom face of the TV Vibration prevention cushions 4 ONKYO Onkyo Corporation Kitahama Chuo Bldg 2 2 22 Kitahama Chuo ku OSAKA 541 0041 JAPAN http Awww onkyo com The Americas Onkyo U S A Corporation 18 Park Way Upper Saddle River N J 07458 U S A For Dealer Service Order and all other Business Inquiries Tel 201 785 2600 Fax 201
Download Pdf Manuals
Related Search