Ergotron StyleView
Contents
1. DO NOT OBSTRUCT AIR VENTS Obstructing air vents may cause overheating and result in equipment damage Center CPU in storage area To increase space and improve airflow power brick may be stored under the storage area If computer with cables is too wide then follow these instructions 10 16 888 24 299 G 00 rev 10 14 Adjustment product resulting in a change in the weight of the mounted load you should repeat these adjustment steps to ensure safe and optimum operation Adjustments should move smoothly and easily through the full range of motion and stay where you set it If adjustments are difficult and do not stay in the desired position follow the instructions to loosen or tighten the tension to create a smooth easy adjustment motion Depending on your product and the adjustment it may take several turns to notice a difference It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps Any time equipment is added or removed from this G Lift Up and down Release Brake to move riser CUSTOMER ADJUST te LIFT TENSION AFTER SET UP SEE MANUAL 822 421 00 NOTE Adjustment may require 40 60 revolutions b Tilt Forward and Backward Q Follow these instructions to tighten or loosen tension 20 fe 6 ree 888 24 299 G 00 rev 10 12. Failure to heed this warning may result in serious personal injury or property damage 822 311 888 24 299 G 00 rev 10 14 7 16 Set up To increase space and improve airflow power brick may be stored under the storage area 6 2x 3 9 12mm WARNING DO NOT OPERATE WITHOUT GUARD IN PLACE Only AWA R N N G remove guard when routing a cable with a large connector through DO NOT OPERATE the bottom of the compartment Replace guard imediately after af WITHOUT routing cable Failure to replace guard my result in equipment GUARD damage and or personal injury IN PLACE 82244700 8 16 888 24 299 G 00 rev B 10 14 Set up 7 Place computer and AC power adaptors in compartment Do not place power bricks near computer or compartment air vents M4 10mm C Plug the following factory connected cables into your computer USB This cable runs from the USB Hub to your computer and uses your computer to power the USB Hub Keyboard Lights and Fan NOTE Your computer must be turned on for the USB Hub Keyboard Lights and Fan to function WARNING Fan must always be running when computer is on Operating computer without fan may lead to overheating resulting in reduced equipment performance 888 24 299 G 00 rev 10 14 9 16 Placement of CPU s in Secure Storage Area USFF Ultra Small Form Factor Thin Client
3. if not installed and Minimisez la tension d l vation AVANT qi 6 used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this de retirer l quipement fix d exp dier le chariot de stocker le chariot equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by Ergotron Inc could void the user s authority to operate the equipment Please contact Ergotron for complete EMC compatibility information www ergotron com 826 501 IMPORTANT This product will need tension adjustments once installation is complete Make sure all equipment is properly installed on the product before attempting range of motion or tension adjustments Any time equipment is added or changed on this product resulting in a different mounted weight you should repeat the adjustment steps to ensure safe and optimum operation This product should move smoothly and easily through the full range of motion and stay where you set it If movement is difficult or the product does not stay where you set it follow the adjustment instructions to loosen or tighten the tension to create a smooth easy motion Depending on your product and the adjustment it may take many turns to notice a difference 2 16 888 24 299 G 00 rev 10 14 Features amp Specificat
4. without notification to its users For the most current i ion or to know if this document is available in languages other than those herein em ele ne NE Tokyo Japan www ergotron com please contact Ergotron No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise www ergotron com info oem ergotron com without the prior written consent of Ergotron Inc 1181 Trapp Road Eagan Minnesota 55121 USA Patents Pending and Patented U S amp Foreign Ergotron is a registered trademark of Ergotron Inc apaccustomerservice ergotron com 16 16 888 24 299 G 00 rev 10 14
5. 4 11 16 Adjustment Lift Up and down Q Follow these instructions to tighten or loosen tension 12 16 888 24 299 G 00 rev 10 14 Auto Lock Drawer k k CAUTION Only use NiMh rechargeable batteries Using non 6x rechargeable batteries may cause product damage AA Rechargeable Nickel Metal Hydride USB to computer USB to charge ALD Batteries may not come fully charged and may need to charge for several hours To charge ALD batteries batteries computer needs to be powered on and connected to the USB hub OS CAUTION Open only one drawer at a time Do Not push cart when drawers are open Failure to follow these instructions may cause the cart to be unstable NOTE User should change Master Personal Identification Number PIN upon receipt of cart Lost Master PIN Contact Ergotron Customer Care for instructions All PINs may vary in length from 4 7 digits Number of PINs possible Carts using StyleLink will store up to 1 000 PINs on the cart Carts not using StyleLink will store up to 100 PINs on the cart Ergotron recommends the following for choosing PIN digit length assumes less than 1 in 25 chance of guessing random User PIN Max number of User PINs lt 50 5 digit length recommended Max number of User PINs gt 300 6 digit length recommended For maximum security use PIN length of 7 Set up Master PIN for the First Time Default Master PIN 12345 Contact Ergotr
6. 5 102mm 448mm 70mm 23 58 mm B tt gt 2 75 70 mm lt 12 25 lt 1 38 TUNE ps lt 197 Front View ae 552 m 311 mm When figuring dimensions 17 75 __ include mounted accessories an gt N gt 2 75 451 gt 4 25 protruding cables and e 14 75 375mm 25 70 mm pom 108 mm port replicators or docking Side View 4 16 lt 13 stations 330 mm e C Top View 888 24 299 G 00 rev B 10 14 888 24 299 G 00 rev 8 10 14 Release Brake to move riser CAUTION Completely release brake engagement before raising or lowering the cart Raising or lowering the cart with the brake partially engaged may cause product damage M3 5 6mm 5 16 6 16 888 24 299 G 00 rev 10 14 Set up b AO 5 3 gt 5 1 5 Goss fre ow 6 Connect Keyboard and Mouse to USB Hub SSeS ET STD 60 96 26020 67024 eS LL 7 EN USB Type A USB Type A NOTE Bar Code Scanner should be connected directly to N computer USB port DO NOT connect Bar Code Scanner to the USB Hub 1x 6 M4x5mm b 75x75min T00x 100m 2 Impact Hazard Moving Parts can Crush and Cut 7 Raise monitor to top of vertical AR adjustment BEFORE removing
7. User Guide StyleView SV43 Cart with LCD Arm ERGOTRON Tools Needed Gai Se BS yO 14mm 9 16 14 Maintenance amp Safety s26 1S01S666 15 16 M4 12mm For service and warranty visit www ergotron com For local customer care phone numbers visit http contact ergotron com For the latest User Installation Guide and StyleLink Software Download please visit www ergotron com User s Guide English Gu a del usuario Espanol Manuel de l utilisateur Francais Gebruikersgids Deutsch Benutzerhandbuch Nederlands Guida per l utente Italiano Anv ndarhandbok svenska HO Bgm LILH L HUUU UU 888 24 299 G 00 rev 8 10 14 a www ergotron com USA 1 800 888 8458 N Europe 31 0 33 45 45 600 China 86 769 86018920 1 16 Features amp Specifications 1 Height Adjustable LCD Mount attaches LCDs or tablet PC s with 75x75 or 100x100mm mounting interface Worksurface 2a Worksurface Lock and Release Secure Storage for Laptop Thin Client or CPU Front Handle Height Adjustment Brake Handle USB Hub connects keyboard and mouse USB cables Keyboard tray slides out tilts and allows for right or left mousing with attached mouse holder Keyboard Light under Front Handle 9 Keyboard Light Switch 10 Cable Management and Storage for excess cables and power supplies 11 Storage Basket and Rear Handle 12 Front Locking Casters 13 Quick Referen
8. and return mouse scanner and other accessories to their places 3 Unlock both front casters 4 Push cart from rear with elbows bent at about 90 to maximize control and minimize muscle strain 5 Don t run out e Before moving make sure cord is unplugged from outlet and hooked to basket for safe travel Remember charge battery fully 100 every day 888 24 299 G 00 rev B 10 14 Maintenance amp Safety Signal Word Level of Hazard Color Hazard Symbols Review Symbol The Meaning of Symbols appearing in this Guide on the Cart or on the Power System These symbols alert you to a safety condition that demands your attention You should be able to recognize L T and understand the significance of the following Safety A Indicates a potentially hazardous situation which if not Indicates an imminently hazardous situation which if not avoided will result in death or serious injury Hazards if you encounter them on the Cart or within Cart avoided could result in death or serious injury documentation such as this Set up Guide Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury Used without the safety alert symbol indicates a potentially CAUTION hazardous situation which if not avoided may result in property damage INSTRUCTIONS Follow operating instructions EQUIPMENT amp ACCESSORIES DISPOSAL 1 Please dispose of all batteries in accordance with local
9. ce Card 14 Scanner Holder 15 Antimicrobial worksurface and antimicrobial coating on wrist rest 16 Auto Lock Drawer see page 3 for drawer configurations QU MT qui Temperature Range Temperature Range 14mm 9 16 325 Relative Relative CAUTION Close worksurface before opening drawers Open Morel Humidity only one drawer at a time Do Not push cart when drawers or A LA market after 13 August 2005 Range worksurface are open Failure to follow these instructions may IMPACT HAZARD Operational inane cause the cart to be unstable MOVING PARTS CAN CRUSH AND CUT Failure to heed this warning may result in serious personal injury or property damage Minimize Lift Tension BEFORE This Class A digital apparatus complies with Canadian ICES 003 Removing Mounted Equipment Shipping Cart Storing Cart Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada DANGER D IMPACT FCC Compliance Statement LES PARTIES EN MOUVEMENT PEUVENT CRASER ET COUPER The cart has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules Il existe un risque de blessure corporelle ou d endommagement These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in mat riel en cas de non respect de cet avertissement a commercial environment This equipment generates uses and can radiate radio frequency energy and
10. eck to make sure drawer cable is installed securely All LEDs blink green 3 times PIN entry accepted e Remove power from drawer system for 10 seconds and re apply All LEDs flashing red Firmware update in progress LEDs flash red green after User PIN in entered All LEDs flashing red green System power ON or low battery condition Battery charge is low check to make sure USB charging cable is plugged into computer and computer is ON Adjustment Keyboard Light 1 Turn Computer on 2 Test Keyboard Light Keyboard Light will automatically turn off after 15 minutes if not manually turned off Ergonomics Working customize to your size 1 Settop of monitor screen about one inch below eye level Release brake and lift or lower riser as needed 2 Tilt screen for comfortable viewing and to reduce eye and neck strain 3 Pull keyboard tray forward and position mouse tray on right or left as needed 4 Work with elbows bent at about 90 to minimize muscle strain 5 If the riser moves up and down with difficulty or if it drifts out of set position consult the product manual for adjustment information 6 Stay in charge Powered carts should be plugged into outlet as often as possible to keep battery charged and computer running 14 16 Moving stow before you go 1 During normal movement release brake and lower worksurface to lowest position for optimal stability and unobstructed view 2 Tuck away open trays
11. g LED for that row will light solid until it is placed back into its original location 4 Pharmacy PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice 888 24 299 G 00 rev 10 14 13 16 Auto Lock Drawer Unlock Drawer 2 methods NOTE All Drawers in row must be closed before a new row can be unlocked Enter User PIN only numbers for available drawer rows flash green then press desired drawer row number e Key turn clockwise 1 4 turn Drawer Row Numbers Lock Drawer e Wait 4 seconds for lock to engage automatically NOTE Always ensure drawer is pushed in all the way and engaged with lock Drawer Troubleshooting LEDs Alarm Meaning No LEDs on keypad when pressing any number 1 2 3 4 or 5 LED ON green Corresponding Drawer is open Verify battery box is connected to controller 1 2 3 4 or 5 LED flashing red and alarm sounding Corresponding Drawer is open longer than 20 e Verify keypad cable is connected to controller seconds Mute alarm by pressing flashing button corresponding to open drawer e Verify battery box switch is in the ON position and that batteries are All available drawer numbers flashing green Waiting for drawer selection see Unlock Drawer properly installed All LEDs flashing green Pharmacy mode all drawers are unlocked e Drawer selection not available when User PIN is entered All LEDs blink red twice PIN entry rejected exit current mode after 5 seconds timeout e Ch
12. ions Part Number Auto Lock Drawer SV43 1210 0 SV43 1220 0 3V43 1240 0 SV43 1260 0 SV43 1290 0 Auto Lock Drawer Weight Capacity A Ibs 6 4 kg 0 Ibs 0 kg Open Worksurface lt 5 165 2 3 kg Closed Worksurface 7 lt 13 Ibs 5 9 kg CPU Compartment 178 mm N li 5 NS 22 12 lt 2 Ibs 0 9 kg ME see inset below ae Combined LCD and CPU Compartment weight lt 27 05 12 2 kg A CAUTION the combined LCD and CPU weight is greater than 27 lbs 12 2 kg then the CPU must be 180 mounted to the rear of the cart using the Universal CPU Holder accessory ordered separately Total weight capacity per drawer gt 2 lbs 1 kg 0 25 Ibs 0 1 kg Total weight capacity per drawer 888 24 299 G 00 rev 10 14 3 16 Features amp Specifications LS eee 4 1 1 22 102 279 50 5 022mm 707 la 19 5 495 mm 17 432 mm 13 4 3 27 3 4 340 mm 83 mm 86 mm 31 W 787 mm 40 8 5 1016 216mm 2 5 31 51 64 mm 787 1295 mm 390 mm 95 mm 19 75 17 5 502 mm 23 43 445 mm 584 1092 mm 16 75 425 mm x P 19 25 c 4 2238 12 4 2 51 mm 4 568 mm 315 mm 21 102 mm 533 mm CPU Compartment lt lt 17 63 gt 2 7
13. let Recommended Periodic Inspection and Maintenance UI Ethernet USB Inspect for wear pinching bad Monthly cables connectors Inspect for dust at intake vacuum Fan on side of CPU as required using a vacuum cleaner joel n usd compartment that DOES NOT generate ESD y Electrostatic Discharge Casters Inspect for wear and debris Monthly Inspect to ensure that maximum Maximum Load recommended loads are not Daily Any user exceeded 1 Please dispose of all batteries in accordance with local law 2 Always replace with similar size battery 33 A h to replace 33 A h and always replace in pairs Americas Sales and Corporate Headquarters EMEA Sales 1181 Trapp Rd Amersfoort The Netherlands St Paul MN USA 31 33 45 45 600 800 888 8458 www ergotron com Jacomo ee 1 651 681 7600 info eu ergotron com www ergotron com While Ergotron Inc makes every effort to provide accurate and complete information on the installation and use of its products it will not be held liable for any editorial errors or omissions including those made in the process of translation from English to another language or for incidental special or consequential damages of any nature resulting from furnishing this instruction and performance of APAC Sales Worldwide OEM Sales sales ergotron com equipment in connection with this instruction Ergotron Inc reserves the right to make changes in the product design and or product documentation
14. lil INSTRUCTIONS Follow operating instructions law 2 All Electronics should be recycled through an electronics recycler ON OFF push push 3 Remaining plastics and metals can be recycled NOTE Each position ON OFF is a stable position through a commercial recycler A and Maintenance The following procedures are not guaranteed to control infection The hospital infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes Ato avoid risk of electric shock do not expose electrical components to water cleaning solutions or other potentially corrosive liquids or substances Do not immerse Cart or Cart components in liquid or allow liquids to flow into the Cart Wipe all cleaners off surface immediately using a damp cloth Thoroughly dry surface after cleaning Do not use flammable cleaners on Cart surfaces due to close proximity of electrical power and equipment All paints and plastic Cart components will withstand cleaning by most commonly used diluted non abrasive solutions such as quaternary ammonia compounds ammonia enzyme cleaners bleach or alcohol solutions Pen and permanent and dry erase markers can be removed with 91 isopropyl alcohol and a soft cloth lodine stains can be removed with commonly used cleaners and a soft cloth Never use steel wool or other abrasive materials that will damage the surface finish e Do not use strong solvents such as
15. nal injury Contact Ergotron Customer Care for information about moving Cart components 888 24 299 G 00 rev 10 14 15 16 Maintenance amp Safety Safety Alerts Associated with this Product The following Warnings Cautions appear in this reference guide or on the cart NOTE Failure to adhere to these guidelines may result in equipment damage or personal injury AX caution the lift brake helps stablilize the worksurface and keyboard tray during normal use but it DOES NOT increase load capacity DO NOT load riser with equipment totaling more than the maximum weight capacity specified by Ergotron Ensure optimum lift function by testing and if necessary re adjusting tension whenever the weight mounted to the riser changes i e equipment is removed or added See Set Riser Lift Tension adjustment instructions CAUTION Do not operate StyleView Cart with missing or damaged components Do not remove modify or substitute Cart components without consulting Ergotron If you encounter problems with Cart installation or operation contact Ergotron Customer Care CAUTION DO NOT overtighten fasteners Overtightening may cause damage to your equipment A warnine Stored Energy Hazard The worksurface lift mechanism is under tension and will move up rapidly on its own as soon as attached equipment is removed For this reason DO NOT remove equipment unless the worksurface has been moved to the highest position on the tower Failure to follow this in
16. on Customer Care for instructions if Master PIN is lost 1 Enter default Master PIN 1 2 3 4 5 then press ENTER 2 Press 5 for Master PIN Entry mode 3 Enter new Master PIN and press Enter LEDs will blink green if PIN is accepted 4 Master PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice Master PIN Mode Menu Enter Master PIN and then select one of the below numbers to enter that mode 1 User PIN Entry Mode 2 Pharmacy PIN Entry Change Mode 5 Master Pin Change Mode Programming User PINS 1 Enter Master PIN and press ENTER for Mode Menu 2 Press 1 for User PIN Entry Mode 3 Input new User PIN and press ENTER All LEDs blink green if PIN is accepted You may enter multiple USER PINs consecutively 4 User PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice NOTE User PIN cannot be the same as a Master PIN or Pharmacy PIN Once maximum User PIN storage is exceeded the oldest User PIN will be over written Programming Pharmacy PIN Note System will hold 1 Pharmacy PIN Pharmacy PIN allows all drawers to unlock at the 1 Enter Master PIN and press ENTER for Mode Menu same time Drawers should then be opened at least slightly as the system will auto lock after 2 Press 2 for Pharmacy PIN Entry Mode 10 seconds All LEDs will flash green until system auto locks Once a drawer is opened the 3 Input Pharmacy PIN and press ENTER all LEDs blink green in PIN is accepted correspondin
17. struction may result in serious personal injury and or equipment damage When Shipping the cart set the worksurface lift mechanism to the lowest tension setting CAUTION DO NOT loosen tighten or remove any other nuts or bolts on the riser or top of tower Tampering with nuts or bolts may result in an unstable Cart leading to equipment damage and or personal injury CAUTION Release Lift Brake before moving work surface Moving work surface while Lift Brake is engaged may cause serious damage to Lift Engine WARNING In the event that repair of the StyleView Cart is needed contact Ergotron Customer Care immediately Cart repair can only be performed by Ergotron Inc or by an Ergotron authorized agent warning This cart is not intended for use in a flammable anesthetic mixture or oxygen rich environment Configuration amp Safety Additional multiple socket outlet or extension cord shall not be connected to the medical system When used in a Medical Electrical system connect only equipment that complies with IEC ISO UL ANSI or CSA standards that are relevant to that equipment Risk of shock or personal injury when connecting non medical equipment supplied as part of a system directly to the wall outlet when non medical equipment is intended to be supplied by the multiple socket outlet Risk of shock or personal injury when connecting any equipment that has not been supplied as part of the medical system to the multiple socket out
18. trichloroethylene and acetone These solvents will damage the surface finish It is recommended that any cleaning solution be tested on a small inconspicuous area to ensure surface is not harmed A sajustment Service Replacement DO NOT attempt to adjust service or replace any part of the StyleView Cart unless directed to do so through Ergotron approved documentation i e installation instructions Only Ergotron Inc or an Ergotron certified entity may adjust service or replace StyleView Cart components If any component on the Cart is missing or damaged the Cart must not be used contact Ergotron Customer Care immediately to request a replacement part Cables Keep cables neatly organized on the Cart a variety of solutions are provided with your cart for this purpose Excess cables should be routed away from moving components with cable clips Review Cable Routing section of this guide or contact Ergotron Customer Care for more information casters Check casters periodically to make sure they are clean and free of debris that would prevent smooth travel Avoid moving Cart across uneven dirty or damaged surfaces Customer Equipment Make sure equipment is balanced and mounted securely to Cart Do not reposition Cart components on riser or tower unless instructed to do so in the installation instructions Moving Cart components too high or too low on the Riser may create an unstable condition leading to equipment damage or even perso
Download Pdf Manuals
Related Search