Ipevo IS-01
Contents
1. Start Menu gt Program files gt IPEVO gt IS 01 gt Calibration Mac Application folder gt IPEVO IS 01 gt Calibration Note the Interactive Pen must have batteries and be switched on for calibration and operation Calibration Steps Step 1 Sensor Cam Coverage Detection Tap each corner white square in any order with the tip of the Interactive Pen Make sure the resulting dots appear inside the center white box If not please move the Sensor Cam until all points are contained within the white box Then press Space to continue Va Tap Corners and Adjust Sensor Cam Tap each comer white square in any order with the Pen Make sure the resulting dots appear inside the center white box If not please move the Sensor Cam until all points are contained within the white box Then press Space to continue Press ESC to abort calibration Step 2 Accuracy Check With the Pen tap the center of each red crosshair that appears Four crosshairs will appear in total You MUST tap all four in turn Failing to do so may impair Pen accuracy X Tap Crosshairs to Calibrate With the Pen tap each crosshair that appears A total of 4 crosshairs will appear 71 Step 3 Calibration Completed After the process you will be returned to your desktop and your IS 01 will be ready for use Sensor Cam Diagnosis If you find the pen trace dithering or inaccurate after the initial calibration your Sensor Cam may need2. cursor may lose accuracy if the screen resolution or screen ratio has changed or if the Sensor has been moved Please run the calibration program again Why is there no scrollbar in my browser or finder window in Mac OS X when using IS 01 By default scrollbar is enabled only when a mouse is connected to Mac You can manually enable the scrollbar by going to System Preferences gt General and set Show scroll bars to Always to enable scrollbars Troubleshooting When I tap on the corners during calibration the points don t fall within the center white box Move the Sensor closer to the area where the corresponding points do not appear Or move the Sensor further away from the screen Run the calibration program again The cursor on my screen is jumping around abnormally and I am not able to control it Remove any strong light source or infrared equipment close to the Sensor as these may interfere with the Sensor During calibration multiples spots appear or spots appear erratically 1 Remove any strong light source or infrared equipment close to the Sensor as these may interfere with the Sensor 2 Ensure the projector screen you are using is not made of highly reflective glass or metal Such reflective materials affect Sensor operation The pen trace continually breaks when write or draw with the Interactive Pen 1 The Sensor might be placed too far away from the screen Move the Sensor closer to the screen and ru
3. to ensure maximum accuracy Installing It cont d 3 Ensure the mounting surface is clean and free of grit Remove the sticker from the bottom of the ceiling mount and affix the ceiling mount firmly onto the mounting surface Note The sticker of Ceiling Mount is extremely adhesive and should only be applied once The Sensor Cam can be detached without removing the Ceiling Mount Simply unscrew the Sensor Cam from the Ceiling Mount C Using a tripod The Sensor Cam comes with a built in tripod mount Consider mounting the Sensor Cam onto any standard tripod 4 Connecting to the Computer Once you ve placed and secured the Sensor Cam connect it to your computer using the included USB cable The Sensor Cam LED indicator will light up once connected 5 Readying the Interactive Pen Remove the battery cover from the Interactive Pen and insert 2 AAA batteries Replace the cover Turn on the pen when ready to use j r C 00 p L cl oo ED am i lt 10 Installing It cont d 6 Calibration IS 01 must be calibrated before use to ensure accurate operation This process only takes a couple of steps The calibration application appears the first time the Sensor Cam is connected to the computer Use the Interactive Pen and follow the instructions on screen and reprinted below to complete the calibration Any time after the first time that you wish to calibrate execute the following file PC
4. DMG file A folder named IPEVO IS 01 will appear e Drag the IPEVO IS 01 folder into the Application folder to complete the installation 2 Positioning and Connecting the Sensor Cam Proper position of the Sensor Cam is important for optimum operation Follow these guidelines to place the Sensor Cam e For most projectors a good position for the Sensor Cam will be the same location as the projector One exception to this is if you are using a short throw projector In that case you will need to place the Sensor Cam further away from the screen than the projector e Minimal distance from your screen depends on screen size Place the Sensor Cam according to the recommended distances in the chart below 50 6o 8o f io Minimal 5 ft 5 5 ft 7 5 ft 9 5 ft Distance 155 cm 170cm 230 cm 290 cm e The Sensor Cam should face directly at the projection screen Depending on your screen s height you will have to adjust the Sensor Cam s Head to face upward or downward Please refer to the steps below Loosen 2 Adjust Angle Tighten a Installing It cont d e The Sensor Cam is best placed opposite the center of the screen at a straight on angle However a straight on angle is not required for acceptable operation and the Sensor Cam may be placed at another angle if necessary Please refer to the diagram below for placement zones according to accuracy quality Sensor Cam Placement Zone Proj
5. Interactive Whiteboard System User Manual www ipevo com Table of Contents What sin ihe BOX csse a aaae AUNE 1 ME Ba ES ease sso ce sa E EE E E E 1 TWO Ways tO Use Meenas S E EEEE EE ESEE 2 AOWA OK Eessen E A E A AEE Get to Know lt snseseseseneesosesosesesessesesosescsessssososesesesseessescsosescsessesososcsosessoessesesoseseoe 4 eaa E E T crmereerneese ete 5 11 Step 1 Software amp Driver Installation ccccccccesssssssssseeccceccceeesseesseeeeees 5 Step 2 Positioning and Connecting the Sensor Cam cccccccceceeeeeeeeees 5 6 Step 3 Securing the Sensor Cam cssssssssssssssssssssseeeeeseeeeeeeeeeeseees 6 8 Step 4 Connecting to the COMPUTE sseccssecteccecccecceccecccecceceseceeeees 9 Step 5 Readying the Interactive Pen cccccccccceccecccesesseeeeeeseeseeseeeseeees 9 Step Cag U ON erences ccinstaaanctses ate vos dog npest aE NENE EE NE EE EE Ea EAEan ae 10 11 ES WTS asa E E E S EAE E E EA T 12 Using IPEVO Annotator Software eeeesseseeeeseseesseeseesssssssssssssssssssssssessssssssssssnso 13 15 E EE A E E EATE EE A E A E E A A 16 What s in the Box Congratulations on your purchase of the IS 01 Interactive Whiteboard System After a few simple steps your system will be calibrated and ready to use Your package should contain the following e IS 01 Sensor Cam e Ceiling mount e IS 01 Interactive Pen e User Manual this document e 2m USB cable e Software CD ROM e Replace
6. able Pen Cap e 2 AAA Batteries N J o e8 AAA Replaceable USB Cable Batteries Pen Cap Interactive Pen Sensor Cam User CD Rom Ceiling Mount Manual Warning Disassembling the pen tip may damage the Interactive Pen Please refrain from loosening or disassembling the pen tip at all times Do not disassemble The Basics The IPEVO Interactive Whiteboard System or IS 01 turns your large projector screen into an interactive touchscreen giving you the ability to easily draw and annotate for education and business Plus because IS 01 is compatible with many different kinds of software you ll also be able to control your computer and what s on the screen at a distance And this is all possible no matter what make and model of projector you have Two Ways to Use It Use the Interactive Pen as a Computer Cursor The Interactive Pen can behave like a mouse transforming any surface into a touchscreen Use the Pen to intuitively perform the actions you d normally use your mouse to perform Note The Interactive Pen can perform normal mouse actions including click double click and drag However some actions are not executable with the Pen such as hovering Err Annotate Your Text and Images Using IPEVO Annotator you can draw and write directly on your interactive whiteboard You can even draw on top of your document camera s live video feed Engage your audience and clarify your material How It Works IS 01 is made u
7. ected Image U navai lable f U navaila ble H Sensor Cam n i k s Excellent Poor 55 A Good R 55 45 R 45 30 30 As you can see e Accuracy is better when the Sensor Cam is closer to the center e Accuracy decreases as the angle increases e Larger screens require more distance between the screen and the Sensor Cam Note Please keep a clear path between the Sensor Cam and the projector screen to ensure proper operation 3 Securing the Sensor Cam Once you ve found the right position it s important to make sure your Sensor Cam is steady and secure There are three ways to secure your Sensor Cam depending on your setup A Placing on the desktop Use a flat smooth desktop surface Make sure nothing is blocking the Sensor Cam s path to the screen surface Adjust the knob to angle the Sensor Cam directly at the center of the screen surface B Using an upside down ceiling mount IS 01 can be mounted upside down onto the ceiling or ceiling mounted projector To do so 1 Twist the Sensor Cam base onto the screw on the ceiling mount until tight Turn the star shaped knob near the base for additional angle adjustment 2 Before affixing the mount to the ceiling hold the Sensor Cam in an area just below by a few inches where you intend to mount the projector Run the Sensor Cam Position Diagnosis see Page 11 with the Sensor Cam in this position
8. en using a larger or taller screen attach the Extension Wand Accessory to the Interactive Pen to help reach all areas of the screen The 16 5 420 mm Extension Wand for Interactive Pen is available at www ipevo com 5 52 25 ow 10 N Installing the Extension Wand Simply push the Extension Wand into the bottom of the Interactive Pen till you hear a click Using IPEVO Annotator Software IS 01 comes with IPEVO Annotator a program which can be used in combination K with any other software application You can draw write and annotate onto images on the screen Or you can create a blank whiteboard to turn your IPEVO Annotator Projector screen into an interactive whiteboard Software After calibrating IS 01 you can start IPEVO Annotator by navigating to Windows Start Menu gt Program Files gt IPEVO gt IS 01 gt Annotator Mac Application Folder gt IPEVO IS 01 gt Annotator 13 14 IPEVO Annotator Software cont d Desktop Mode Finder File Edit View Go Window Help Will Ot Ao as usr Q E g Click the Computer icon to select Desktop Mode gt Mee Save all of your current screen as Use your connected IPEVO doc cam s Top an image live feed as your background a oe Save part of your current screen as For more specific instructions click an image the Settings icon Display a touchscreen keyboard Clicking the small reverse arrow on either side of the screen will
9. further adjustment Please run the Sensor Cam Diagnosis and reposition the Sensor Cam according to the suggestions given This diagnostic tool is located in Windows Start Menu gt Program Files gt IPEVO gt IS 01 gt Sensor Cam Diagnosis Mac Application folder gt IPEVO IS 01 gt Sensor Cam Diagnosis 11 12 Using It Controlling cursor movement Simply move the pen in front of the screen area being careful not to block the Pen s path to the Sensor Cam with your body The mouse cursor will follow the Pen s movement in real time Controlling the computer and applications Mouse clicks can be performed both within the operating system and in a wide variety of software applications To do so use either of two methods Touch the contact sensitive Pen tip Press the green button onto the screen surface A variety of mouse controls are possible using these methods Left click Tap the tip onto the surface or press the IPEVO button once Double click Quickly tap the tip onto the surface twice or press the IPEVO button twice Right click Press and hold the tip onto the surface or press and hold the IPEVO button Hold for at least 2 seconds Click and drag Press and hold the tip onto the surface or press and hold the IPEVO button While doing so move the pen to the desired spot Using It cont d Adding reach with the Extension Wand Optional Accessory Wh
10. n the calibration program again 2 Pen trace can only occur if the Sensor vision field is not blocked Please do not draw or write with your body blocking the Sensor 3 Replace the batteries in the interactive pen Low batteries can have an adverse affect on pen trace and accuracy My pen trace and pointing are inaccurate after change screen resolution Changing the screen resolution throws off the calibration Please run the calibration app after every resolution change My pen and cursor lose accuracy every now and then Please make sure the Sensor Cam is positioned on a flat and stable surface and that the Adjustment Knob is tight A slight tip of the Sensor Cam may result in inaccurate operation have the task bar set to hidden and can t use the task bar with the Interactive Pen Please uncheck the auto hide option and position the task bar on the screen when using IS 01 17 2013 IPEVO Inc All rights reserved IPEVO IPEVO Annotator IS 01 the IPEVO logo and other IPEVO marks are owned by IPEVO Inc and may be registered All other trademarks are the property of their respective owners Customer Service Customer Service USA International Email cs ipevo com WWw ipevo com Email service ipevo com Tel 1 408 490 3085 Tel 886 2 5550 8686
11. p of two devices the Sensor Cam and the Interactive Pen The Sensor Cam detects the physical location of the Pen and sends this information to your computer which then translates the Pen s motion into cursor motion Wherever you move the Pen the computer will move its cursor in real time You can also perform mouse clicks and drags with the Pen INTERACTIVE PEN Emits infrared signals on contact or by pressing the green button SENSOR CAM _______1__ O Reads infrared signals and Ca sends them to your computer Get to Know It Contact Sensitive Tip Send signals for left right and double mouse clicks Brief contact performs a left click while pressing in and holding for 2 seconds or longer performs a right click USB Port Connect USB here Power switch Turn the unit on and off LED indicator Lights up when powered up and connected IPEVO button This is another way to perform mouse clicks Press for a left click or press and hold for 2 seconds or longer for a l ne right click Detects signals emitted by the Interactive Pen Battery cover Open to reveal slots for 2 AAA batteries Adjustment Knob Change and secure sensor angle by tightening knob Installing It 1 Software amp Driver Installation PC Insert the CD ROM into your computer and follow the onscreen prompts to complete the installation Mac e Insert the CD ROM into your computer e Double click the IPEVO IS 01
12. show the toolbar again on that side Hide the toolbar Drawing Mode Click the Pen icon to select Drawing Mode to draw shapes and lines Create or select your whiteboard Select one of two drawing tools Click on the icons to change color T and line size Mouse Erase your drawings i Clear all your drawings Select shape tools Undo and Redo 15 16 FAQ How do quickly determine a good working distance between the screen and Sensor Normally the projector is a good location to place the Sensor If you are using a short throw projector however please refer to pages 5 and 6 for the recommended Sensor distance guidelines Can I use rechargeable AAA batteries for the Interactive Pen Yes Rechargeable alkaline batteries are recommended Can I use IS 01 with my own software instead of IPEVO Annotator Yes IS 01 can be used with third party image processing software and whiteboards Any mouse based software should work fine How do I stop the IS 01 driver from running at start up Follow these steps according to your system Mac System Preference gt Users amp Groups gt Login item Uncheck IS 01 Driver PC Start Menu gt Enter msconfig in Run Windows XP or Search Bar Windows Vista amp 7 gt Startup tab gt uncheck IS 01 Driver gt OK Restart to apply this setting What should I do if the cursor is not pointing correctly and or following the Interactive Pen correctly The
Download Pdf Manuals
Related Search