EZ Dupe MediaMirror
Contents
1. Function Introduction Function Table Disc to Disc Duplication When you select Disc duplicate you will enter the disc to disc menu if you pee RUDE select Multimedia Dupe you will only access the Flash to disc menu Function Sub function Description To copy disc to disc or copy disc from 1 Copy HDD 2 Test To simulate copy process 3 Compare To bit by bit compare between source disc and copied discs 4 Copy amp Compare To copy first and compare the copied discs later 5 Set Burn Speed To set burning speed for duplication 6 Select Source To select source from any optical drive or hard disk drive 7 Utility 1 Disc Info To check the formatof disc burning speed supported and total capacity or data size 1 Information 2 Drive Info To check the version model No and brand name 3 System Info To check the model No and firmware version 1 Quick Erase To erase data from rewritable disc 2 Erase Disc 2 Full Erase To erase data from rewritable disc 3 PreScan Source To check source disc s readability 1 Copy Track To select and combine audio tracks from various CDs into a single customized audio CD 4 Track Edit ea To close the disc after track copying to f make the CD playable on CD players 3 Disc Info To check the audio CD s use status 5 Eject All Disc To eject all trays 1 Show Count2. USB with 8GB data copy to CDs or DVDs 2 5 Reminding 1 Disc Spanning doesnot support copying Flash devices with a single large file 2 DVDs or 11 CDs Flash device with a single file cannot use disc spanning function 2 Disc spanning cannot execute with Multidisc mode at the same time when both modes are enable the system will primarily execute disc spanning 3 Each disc will keep some blank space between each session there are also remain blank space at the end of the copy process 4 ONLY ONE Flash device can be inserted at a time 5 This duplicator can copy various Flash Media Memory Cards and USB devices which support FAT12 16 32 file formats lt is not possible to copy Non FAT Flash media 6 When the system is in process DO NOT pull out the flash media 7 CD can only copy to CD DVD copy to DVD II Function Introduction Function Table Multimedia Duplication Multimedia Dupe When you select Disc duplicate you will enter the disc to disc menu if you choose Multimedia Dupe you will only access the Flash to disc menu Function Sub function Description 1 Copy To copy Flash to disc 2 Compare To compare Flash source and copied discs to ensure data correctness li Copy Compare To copy first and then compare Flash source and copied discs 4 Information USB Card Info To show Flash device s used space total capac
3. 1 Insert a Flash device ex USB SD MMS into the proper slot as source and place a disc into the writer tray as target for duplication If you would like to copy many discs at the same time you can place more than one blank disc into the writer drives 2 Select 1 Copy and press 0x to start copying MultiMedia Dure l COF4 3 The system will detect the source and the target disc automatically Total capacity Data size Data size USE 497M 256M USE SEM roe 156M Copy process Copied data size Writings disc Il Function Introduction 4 When the copy task has finished the system will close the session Write Disc 256M Write Disc 256M Fimalizins Disc Complete 5 The disc will be ejected and you can continue to copy another memory card or USB Note i 1 Aslongas the disc was a multi session disc it will not support disc spanning copy 2 If the data size is larger than the disc s capacity the system will reguire you to plug more than one disc Please make sure the disc spanning function is enabled you can set it up in 6 2 Disc spanning page 17 3 Rewritable discs do not support multi session copy Due to the feature of CD RW and DVD RW rewritable format the first session can be copied successfully but when you want to build up the second one the system will erase the first session of RW format disc and an error message Not Blank Disc for RW format disc In Dis
4. It is important to make sure that your source disc is placed in the right drive You can check or select your source reader by function 6 Select Source Please refer to 6 SelectSource page 28 1 Select 1 Copy and place source disc and blank discs into the proper trays Then the system will detect the source disc and show the information 1 Copy x 4 Q ty of target disc sources DUDSSE ZM Data size 2 Press o to start copy Q ty of target Cory X 446201 Data size Speed of burning 1H HE 4x LE SI Copied data size Copy process 3 Once the copy task is finished the copied discs will be ejected and the result of copy task will show on the LCD Cops Azid Elapsed time PASS 3 FAIL A 7 II Function Introduction Note Due to default setting of auto start time the duplicator will start to copy automatically within a few seconds You can set OFF to close the auto start function or set a longer waiting time The default setting is 5 seconds About this setting please refer to 8 1 AutoStartTime page 33 If HDD is selected to be the source reader you have to upload the source to the built in HDD and then follow the copy process to do your copy task How to upload data from disc to HDD please refer to 9 2 Disc to Image page 37 Note The default setting of source reader is the first drive 2 Test This function will simulate the copy process to ensure error free duplication Duri
5. 7 1 Information You can check the information of disc drive and system by this function By pressing W each disc or drive s information will show on the LCD 1 Using 4 Mto select 7 Utility press ex to enter the sub menu Then select 1 Information and press e Utilita 1 Information 2 Using W to select 1 Disclnfo or 2 Drivelnfo or 3 Systeminto and press to see the related information Il Function Introduction 3 The information will show on the LCD as below e Disc Info You can check the format of disc burning speed supported and total capacity If the disc has data you can also check the data size 5 Bx 4 1 Burning Speed Disc Format DDR 44a Capacity Data size e Drive Info The version model No and brand name can be checked here LE Fort Za 1 1 a HA Drive version Pionner DVD Fil Brand name e System Info The model No and firmware version can be checked here T KKK K A Vea dda 7 2 Erase Disc This function will erase the rewritable discs in WRITER tray there are two erase modes available e Quick Erase Will erase the INDEX of the rewritable disc e Full Erase Will erase ALL DATA in the rewritable disc which takes longer time than Quick Erase 1 Place discs into writers 2 Using 4 W to select 7 Utility and press em to enter the sub menu Then select 2 Erase and press ox CUbilityd falllilit da Erase
6. Specification IV FAQ Appendix 37 37 38 38 38 39 39 40 41 42 I Introduction 1 Features e Multi Session MultiDisc Disc Spanning Disc to Disc duplication e High speed DDR2 SDRAM e Support various Flash media interface ex USB SD CF MicroSD e Support high speed 24X DVD 52X CD and 12X Blu ray burning e Special blue back lit LCD display e Support built in HDD to load disc images e Easy operation for separate DVD and Flash to DVD duplication 2 System Overview 2 1 Package Contents Media Mirror Power Cord User s Manual Duplicator 2 2 Media Mirror Multimedia Duplicator _ Control Button Card Reader co o CD DVD Reader D CD DVD Writer O Power Button 3 I Introduction 2 3 Display Interface Display LCD Backward Confirm Execute PO aa e Cancel i On in O soc Forward USB CF MS MS Pro SD MMC 2 3 Media Mirror Multimedia Duplicator Controls USB Drive Input CE WII Card Input Writer Driv Writer Driv LCD Display Down Button MS MS Pro Card Input Up Button Enter Ok Button Esc Back Button SDIMMC Card Input Reader Drive Writer Drive Power Button I Introduction 2 4 Main Function Structure There are two main functions for Media Mirror multimedia duplicator series One function is Disc Duplication Blu ray DVD CD and theotherone is Flash to Disc Duplicatio
7. To check how many discs were successfully copied and failed 6 Copy Counter 2 Enable Counter To enable or disable counter setting 3 Clear Counter To delete the current count 7 Update BIOS To update the system s firmware II Function Introduction 8 Setup 1 Auto Start Time A llowthe system to do the Copy Test Compare and Copy Compare functions automatically 2 Display Mode 1 Basic 2 Show Speed 3 Show Timer 3 Button Beep 4 Eject On Start 1 Eject All Discs To eject all trays with discs inside when the system is booted up 2 Do Not Eject Do not eject any tray ordisc when the system is booted up 3 Eject Target Only Only eject target trays with discs inside when the system is booted up 4 Eject Source Only Only eject source disc when the system is booted up 5 Eject All Trays To eject all trays when the system is booted up 5 Reader Speed To adjust the reading speed of a source drive 6 Compare Speed To adjust the speedofdrives while comparing 7 Language 8 Clear Setup To reset functions back to manufacturer s default setting 9 Advanced Setup 1 Power On Time To set a warm up time from 5 seconds to 99 seconds 2 Startup Menu To select which function you would like to show up in the beginning 3 Skip Reader Error To set skip the re
8. 29 II Function Introduction 3 Using Mto select 1 QuickErase or 2 FullErase Erase Disc Erase Disc L Quick Erase 2 Full Erase 4 Press to execute the erasing task When the system is detecting the discs you will see the colon flashing The Second Drive 5 When the erase task is in process you should see the O ando blinking 6 Once the erase task has finished the O stops blinking the disc will eject automatically Note i 1 If you place a new DVD RW to execute quick erase or full erase the system will format automatically and you will see F and f blinking on LCD display 2 Erase function only supports rewritable discs 7 3 PreScan Source This function will scan and detect any bad sectors existing in the source disc which helps you to ensure the readability of source disc 30 Function Introduction Place a source disc into the reader Use 4 to select 7 Utility and press es to enter the sub menu Then select 3 PrescanSource and press ex to start scan task Utilita Prescan Source When prescan task is in process you will see the process on the LCD display PreScan 446 7 Data size Elapsed time Hz S SUA 1300 canned data size Scan process When the prescan task has finished the result of prescan will be shown on the LCD display 7 4 Track Edit This function enables you to combine audio tracks from various CDs into a single c
9. e Skip Read Error You can set this function to enable skipping disc errors in order to avoid bad quality copies If you are confident that your source disc has only small or insignificant errors due to physical damages and can be overlooked you can select NO to disable this function 35 ll Function Introduction Note Skip Read Error cannot fix the error on the source disc all it does is skip the errors and keeps copying the rest of the readable data e Change Bad Master This setting will make the system eject a bad source disc and ask for another one if the source disc is unreadable by the system e CD Overburn The majority of discs have a small margin of extra groove at the outer edge This setting allows you to copy data over the normal size limit e Show HDD Image Name You can select to show HDD image name or capacity on Copy Test Copy Compare and Compare function Show HDD Image Name Show capacity 1 Cory Source HECD PH l Corps Sources HC ABEL Note When you change the source from drive to HDD the LCD will show the HDD information To change your source reader please refer to 6 Select Source e Keep Buffer You can set Yes to load source disc to buffer in first round of Copy Test Compare or Copy Compare and do it again without the source disc Or set No to keep buffer from being used Note The source will only be temporarily saved in buffer there will be nothing left wh
10. has finished press to go back to the previous menu Compare 560937509 Complete Note i 1 The compare function executes a file by file and bit by bit comparison Therefore comparison speed will be affected by file guantity total content size and Flash device s reading speed 2 While doing multi session disc comparison only one disc is allowed to compare with the source Disc Spanning Compare 1 Insert a Flash device ex USB SD MMS into the proper slot as source and place a disc into writer tray as target for comparison 2 Select 2 Compare and press to start comparison The system will detect the source and the target disc automatically 4 After detecting the system will start to compare Compare 61 446 dv Disc 152 sar Function Introduction 5 When the comparison has finished press to go back to the previous Compare 446 446 Complete 3 Copy Compare This function is to make a copy first and then compare the copied discs with source immediately after the copy task has finished 4 Information Before copying it is recommended to use this function to check each memory card USB or CD DVD s content information You can check Flash device s information ex used space file quantity and discs information ex burn speed supported total capacity and content size in this function 4 1 Flash Device Information 1 Insert a Flash device ex USB SD MMS into the proper
11. MEDIA MIRROR won t transform your data s format You can trust their simple and straightforward copy capability G2 A G3 Q4 G5 G6 G7 Can MEDIA MIRROR play MP3 or JPEG photo No MEDIA MIRROR is designed as a simple and easy to use backup machine Can MEDIA MIRROR link to PC Yes MEDIA MIRROR has an optional USB module Please ask your supplier for this option When hook up with PC to MEDIA MIRROR will become an external CD DVD burner How long does it take to do a Memory Card or USB to disc copy The speed of copy will depend on your Memory Card or USB s speed and the data size Can MEDIA MIRROR erase source disc MEDIA MIRROR only can erase the information of rewritable disc What file Format the MEDIA MIRROR can support MEDIA MIRROR support FAT format such as FAT12 16 and 32 Why is the capacity of my flash memory card as reported by many operating systems different from the capacity that is listed on its label Some Disk Drive Companies define 1 MEGABYTE as 1 000 000 BYTES But the Operating Systems define 1 MEGABYTE as 1 048 576 BYTES 1024K X 1024K or 2 to the 20th power This is the reason why our systems calculate the capacity differently Copyright 2010 All rights reserved
12. Media Mirror Multi Media Duplicator Users Guide Version 3 2 Content Index I Introduction 1 Features 2 System Overview 2 1 Package Contents 2 2 Media Mirror Duplicator 2 3 Media Mirror Interface 2 4 Main Function Structure 2 5 Reminding O O RO O O O ll Function Introduction Function Table Multimedia Duplication 9 Chapter 1 MultiMedia Duplication 10 1 Copy 10 2 Compare 12 3 Copy Compare 14 4 Information 14 4 1 Flash Device Information 14 4 2 Disc Information 15 4 3 System Information 15 5 Utility 16 6 Setup 17 6 1 Multi Session 17 6 2 Disc Spanning 17 6 3 MultiDisc 18 6 4 Burn Speed 19 6 5 Advanced Setup 19 Function Table Disc to Disc Duplication 21 Chapter 2 Disc Duplication 24 1 Copy 24 2 Test 25 3 Compare 26 4 Copy Compare 26 5 Set Burn Speed 27 6 Select Source 28 7 Utility 7 1 Information 7 2 Erase Disc 7 3 PreScan Source 7 4 Track Edit 7 5 Eject All Disc 7 6 Copy Counter 7 7 Update BIOS 8 Setup 8 1 Auto Start Time 8 2 Display Mode 8 3 Button Beep 8 4 EjectOn Start 8 5 Reader Speed 8 6 Compare Speed 8 7 Language 8 8 Clear Setup 8 9 Advanced Setup 28 28 29 30 31 31 32 32 33 33 34 34 34 35 35 35 35 35 9 HDD Manager For HDD installed duplicator 37 9 1 Select Image 9 2 Disc to Image 9 3 Set Reader Speed 9 4 Show Image Info 9 5 Rename Image 9 6 Delete Image 9 7 Show HDD Info 9 8 Format HDD III
13. The MultiDisc copy mode allows you to duplicate multiple discs from one Flash device You can enable or disable this mode here 1 Select 6 Setup and press ex MultiMedia Dure 6 SeLUP 2 Select 3 MultiDisc and press e 6 5 hur J i Burn Multibiso 3 Use A W to enable or disable the copy function Burn Multibisc Burn Multibisc ves Ho Il Function Introduction 6 4 Burn Speed In this section you can adjust Blu ray DVD and CD duplication speed 1 Select 6 Setup and press em MultiMedia Dure 6 SeLuF 2 Select 4 BurnSpeed and press ex LE zeluF J 4 Burn Speed 3 Select 1 CDDisc and press ex 4 Burn Speed LCD DISC 4 Use 4 Wto adjust the proper disc duplication speed The burning speed of a CD is from 1 to MAX The default burning speed setting of Blu ray is 4X DVD is 8X and CD is 40X CD Disc 4h 6 5 Advanced Setup CD DVD BD Spare Size Due to the fact that the outside space of disc is not as easy to write as the inside space you can set spare size to ensure the outside space of a disc is not written in order to keep consistent quality Function Introduction Time Zone This setting allows you to setup the proper time zone in your local area Time Zoned GTM e Language You can set the language you prefer to use during operation Factory Default You can reset all settings to manufacturer default setting with this function
14. aderror and keep copying 4 Change Bad Master To make the system eject a bad source disc and ask for another one if the source disc is unreadable to the system 5 CD Overburn Set to copy overburn CD 6 Show HDD Image Name To show HDD image name or capacity on Copy Test Copy Compare and Compare function 7 Keep Buffer To enable or disable load source to the buffer 8 Boot Password To enable or disable the users administrative password 9 Setup Password To set up the login password 7 Function Introduction To select image file from HDD as your 1 Select Image source for copying To load your source disc to the built in 2 Disc gt Image HDD To adjust the source readers speed 3 Set Reader Speed while you load data from the reader to HDD 4 Show Image Info To check the disc format and image file data size 5 Rename Image To change the name of an image file 9 HDD Manager To delete image file from the built 6 Delete Image in HDD To check the information of the 7 Show HDD Info built in HDD Includes how many discs are stored and the free space available 8 Format HDD To format the built in HDD 23 II Function Introduction Chapter 2 Disc Duplication Select Disc Dupe from the main menu and press 0x to start disc to disc copy operation gt Disc Durlicate MultiMedia Dur 1 Copy
15. ate the firmware of this system by using certified update firmware released by the manufacturer 1 Reguest the firmware from your local distributor 2 Unzip the firmware and save it in a USB drive Note i DO NOT save the firmware in a folder The system can not detect the firmware if you save it in a folder 3 Select 5 Utility and press ex MultiMedia Dure Sa ltilit 4 The system will start to execute updating task Update Process lirilLifris ss II Function Introduction 5 When updating has finished the system will prompt you to reboot 6 Setup This section allows you to setup the multi session disc spanning multidisc disc burning speed and advanced setup 6 1 Multi Session 1 Select 6 Setup and press er Multifledia Dure 6 SETUP 2 Select 1 Multi session and press LE Setur I Mulli Session 3 Use 4 W to enable or disable the copy function Multi Session Multi Sessioni I Enable Disable I 6 2 Disc Spanning 1 Select 6 Setup and press ex MultiMedia Dure 6 SE Cur Function Introduction 2 Select 2 DiscSpanning and press om LE Setur Dise SPannimns 3 Use W to enable or disable the copy function Disc SPannins Disc Spannino Disable Enable Note i Disc spanning cannot be executed at the same time as Multidisc mode When both modes are enabled the system will execute disc spanning 6 3 MultiDisc
16. c Spanning Mode 1 Insert a Flash device ex USB SD MMS into the proper slot as source and place a disc into writer tray as target for duplication 2 Select 1 Copy and press to start copying Multifledia Dure 1 Cory Function Introduction 3 The system will detect the source and calculate how many discs are needed Total neeg 11C0 Discs 4 After detecting the system will start to copy Disc 1 Total discs needed UriteDizio 97m mecc TIL rira fr Copied data size 5 When the first disc has finished copying the disc will be ejected and wait for the next disc Writebisli Sf Wailing Disc Note 1 Disc spanning cannot be executed at the same time with Multidisc mode When both modes are enabled the system will execute disc spanning first 2 Compare The compare function has two different displays for discs copied by Multi Session and Disc Spanning 1 Insert a Flash device ex USB SD MMS into the proper slot as source and place a disc into writer tray as a target for duplication 2 Select 2 Compare and press to start comparison Multifledia Dure Za LomFare Il Function Introduction 3 The system will automatically detect the source and the target disc 4 After detecting the system will start to compare The file compared Total file Compare Compare 39619 waiting for keadina Session 2 61 comparison Compare process 5 When the comparison
17. e and execute firmware update Update Firmuare LEA 4 Once the firmware has been updated the system will require you to reboot the system TURH OFF WAIT 5 Second TURN OM Note i DO NOT save the firmware in a folder The system can not detect the firmware if you save it in a folder 8 Setup 8 1 Auto Start Time This setting will allow the system to do the Copy Test Compare and Copy Compare functions automatically in a few seconds once the source and blank discs are placed in the trays and detected by the system The default setting is 5 seconds You can set a longer shorter time from 1 to 99 seconds or set OFF to disable this function and execute copy task manually 1 Pressing 4 W to select 8 Setup and sub menu 1 AutoStartTime Setup L Huto SLartTime 33 Il Function Introduction 2 Pressing W to set the time Muto StartTime l o seconds 8 2 Display Mode You can select the preferred display mode in Copy Test Compare Copy Compare e Basic Will only show the copy process on LCD display Q ty of target 1 Cor AA Data size Copy process Copied size e Show Timer Will show the copying time 1 Corpy 5 SHRM Elapsed time Hid fre BJA e Show Speed Will show the burning speed during copy process 1 Cops so HEM Speed of burning Gx 77 gazh 8 3 Button Beep This setting will allow you to set up a beep sound when a button is press
18. ed Or not 8 4 Eject On Start You can set the trays or discs to eject once the system is booted up e Eject All Discs To eject all trays with disc inside once the system is booted up e Do Not Eject To not eject any tray or disc once the system is booted up 54 Il Function Introduction e Eject Target Only Only eject target trays with disc inside once the system is booted up e Eject Source Only Only eject source disc once the system is booted up e Eject All Trays To eject all trays once the system is booted up 8 5 Reader Speed This setting allows you to adjust the reading speed of source drive The default setting of reader speed of BD is 4X DVD is 24X and CD is 40 X 8 6 Compare Speed The reading speed of drives and discs is what affects the quality of duplicated discs This setting allows you to adjust the reading speed of target drives to match up the reading speed of discs The default setting of BD s compare speed is 4X DVD is 8X and CD is 40X 8 7 Language You can set a desired language for duplicator menus and functions 8 8 Clear Setup This setting will reset all functions back to the manufacturers default settings 8 9 Advanced Setup e Power On Time You can set a warm up time from 5 to 99 seconds to warm up the duplicator when it is turned on The default setting is 10 seconds e Start up Menu You can select which function you would like to show up when the duplication is turned on
19. en you exit the task Copy Test Compare and Copy Compare or reboot the system e Boot Password This setting allows you to enable or disable the user administrative password Users have to login when the system is booted on e Setup Password You can set up password by pressir to select the number you like and press to set next number Il Function Introduction 9 HDD Manager For HDD installed duplicator 9 1 Select Image You can select image file from HDD as your source for copying When this function is selected the system will automatically set the HDD to be the source reader 1 Press 4 to select 9 HDD Manager and sub menu 1 Select CHEC Manaser i Selecti mace 2 Press 4 W to select the image you need and press to confirm HT He J Image Buldo CD FAZI Data size 9 2 Disc to Image This function will load your source disc to the built in HDD and save the source as an image file 1 Place the source disc in one of the drives 2 Press W to select 9 HDDManager and sub menu 2 Discto Image Function Introduction 4 When loading has finished the disc will automatically be ejected DUD RBB Finished Note i The source disc can be placed in any drive it will not affect the loading process 9 3 Set Reader Speed You can adjust the reading speed of the drive that you use as the source disc This function is ONLY available when you load the
20. ication Disc to Disc Duplication Buffer DDR2 128MB CD Speed Up to 52X DVD Speed Up to 24X Blu ray Speed Up to 12X Memory card or USB Backup to Disc technology Multi session Disc Spanning MultiDisc Memory Card Compatibility CompactFlash MemoryStick Pro Duo SD Card miniSD microSD USB Flash Drive Support CF SD SDHC Memory Stick Pro Duo USB File Format Support FAT12 FAT16 FAT32 Disc Format Support BD ROM BD R BD RE DVD ROM DVD Video DVD Audio DVD R DVD RW DVD R DVD RW Dual Layer DVD R CD ROM CD RW CD I Audio CD Video CD CD G CD TEXT Bootable CD Mixed mode CD Multi session CD CD Extra Business Card CD 3 Mini CD R Display 2X16 Blue Back lit Monochrome LCD Control Button 4 buttons Forward Backward OK Esc LED LED for each Memory card and USB device slots Working 5 C 45 C Temperature Storage 20 C 65 C Working 20 dai 80 Humidity Storage 5 95 Controller Power Voltage Max 5V Consumption Sumen Max 1A Safety FCC CE RoHS The information above is for reference only The actual specifications may be subject to change without notice IV FAQ Q1 Will MEDIA MIRROR transform my memory card data to DVD video or MP3 CD A MEDIA MIRROR will back up whatever you have in your original media devices
21. ity and file quantity Disc Info To show disc s burning speed format and capacity System Info To show the duplicator s model No firmware version Burn Speed To show the burning speed of disc 5 Utility Update BIOS To update the system firmware Multi Session To enable or disable multi session mode Disc Spanning To enable or disable disc spanning mode MultiDisc To enable or disable multidisc mode Advanced setup 1 CD Spare Size 2 DVD Spare To set spare size to preserve the outside Size space of discs not to be written 3 BD Spare Size To setup the proper time zone for your 4 Time Zone location To set the language you prefer to use during 5 Language operation To reset all the settings to manufacturers 6 Factory Default default setting II Function Introduction Chapter 1 MultiMedia Duplication Select Multimedia Dupe from the main menu and press or to start Flash to disc copy operation Disc Duplicate Hullifledia Dur 1 Copy The copy functionin Multimedia duplicationhas three main options Multi Session Disc Spanning and MultiDisc Each mode can be enabled or disabled in Setup function Please refer to 6 Setup page 17 Note Before copying it is recommended to check each memory card USB or BD DVD CD s content information For more info on the check function please refer to 4 Information
22. mage file is deleted the file name will be held for the next new image file the existing file will not fill the vacancy For example there are 5 image files A001 A005 in the HDD when you delete A003 A004 will not change to be A003 once a new file has loaded its default name will be A003 9 7 Show HDD Info You can check the information of the built in HDD which includes how many discs with image files are stored and the free space that is available in the HDD Used ICD SDU Free 14600 29000 39 Function Introduction 9 8 Format HDD This function allows you to format the built in HDD while the HDD is NOT selected as the reading source You can change the source from HDD to other drive in 6 Select Source Due to the capacity for discs loading is hard to predict precisely and more new discs are coming out every day The traditional method of formatting is not ideal for using on this duplicator Our HDD management technology is able to detect disc capacity and automatically assign a proper partition for the discs data You do not have to predict and select BD DVD or CD partition in the beginning You can check how many discs you can upload from 7 Show HDD Info This intelligent HDD management technology is much easier for HDD management than the previous versions 40 Model III Specification Media Mirror Operation Standalone Target 1 2 3 7 8 9 10 Function Flash to Disc Dupl
23. n USB SD microSD MMS bisc Durlicate MultiMedia Dur Disc to Disc Duplication Flash to Disc Duplicator Please refer to Chapter 2 on page 10 for USB SD CF MMS operating instructions 1 Multi Session 2 Disc Spanning 3 MultiDisc Please refer to following sections for operating instructions There are three main copy modes for Memory card or USB copy to CD DVD disc e Multi Session Allows all different types of memory cards with small data to backup to one disc Ex EH Session 1 for Disc 1 ar 100M data ave data Session 2 for Disc 1 Disci Note i Only ONE Flash device can be inserted and copied at a time E I Introduction e Disc Spanning A large capacity memory card with large data content can copy to several discs Ex USB 4GB data Disc 3 4 Disc 4 4 i Note Disc Spanning does not support copying a Flash device with a single large file e MultiDisc Allows you to duplicate multiple discs from one Flash device FX 300M data I Introduction Example of Multi Session MultiDisc and Disc Spanning Flash Source Multi Session MultiDisc Disc Spanning USB with 100MB data copy to a CD First session of CD1 Yes as many blank discs as you need SD card with 200MB data copy to a CD Second session of CD1 Yes as many blank discs as you need Flash device with small data can make multi session Copy
24. ng the simulation there will be nothing written in the recordable discs 1 Using W to select 2 Test and press ex da est x 2 source DUDd4d46 214 2 Press x to Start test Test o 4460 l bx qa LES 3 Once the test task is finished the discs will be ejected and the result of the pass and fail discs for the test task will show on the LCD TEST z ds PASS 5 FAIL amp II Function Introduction Note 1 This function is unable to support DVD R blank disc 2 If you use CD DVD rewritable discs as your blank media in the simulation all the content inside the discs will be erased permanently during test simulation 3 Compare This function will perform bit by bit comparison between source disc and copied discs to ensure the copied discs are identical to source disc 1 Place source disc and blank discs into Reader and Writer separately 2 Using Mto select 2 Compare and press ex to start compare 4 Compare 3 sources DUDSSE 2H 3 The system will detect the source and target discs automatically 4 After detecting the system will start to compare Compare 5 4462 A dx 5d pal 5 When the comparison has finished the system will show the compare result Compare PASS 3 FAIL amp Finished Compare ad 4 Copy Compare This function will do copy task first and execute comparison automatically when copy process is finished Il Function Introduc
25. slot 2 Select 4 Information and press ex MultiMedia Dure 4 Information 3 Select 1 USB Card Info and press to check the devices information Information L USE Card Info 4 The system will detect the device automatically Check Device Function Introduction 5 After detecting the information of the device will display The information includes used space total capacity and file quantity Content size Use 71587776M Total capacity F le 2 File Q ty 4 2 Disc Information 1 Place a disc into a drive tray 2 Select 4 Information and press ex MultiMedia Dure Intformaliori 3 Select 2 DiscInfo and press to check the disc s information Information Z Disc Info 4 The system will detect the disc automatically 5 After detecting the information of the disc will show up The information includes the burning speed supported disc format and content size Allo looks dA DUD F Cer zii Content size 4 3 System Information This function show the systems information which includes the model No and firmware version gt II Function Introduction 1 Select 4 Information and press ex MultiMedia Dure 4 Information 2 Select 3 Systemlnfo and press x to check the system s information C4 Information i osten Info 3 The system information will show on the LCD RARA RA Vis da 5 Utility This function will upd
26. source disc to HDD The default setting for BD DVD and CD speed is MAX 9 4 Show Image Info You can check the disc format and data size of image file in this function 1 Press W to select 9 HDDManager and sub menu 4 Showlmage Info HED Manaser 4 ShoyImaselnfo 2 Press to check the disc format and data size of the image file Press N IV to check other image file s information AHi CAL Audi ol razh 9 5 Rename Image This function allows you to change the name of an image file You can set a maximum of up to 8 characters for a new name NO blank is allowed between the characters II Function Introduction 1 Press W to select 9 HDD Manager and sub menu 5 Rename Image HED Manaser D Rename Imase 2 Press ex and select which image file you would like to rename by pressing 4 W and then press ex to start create a new name for the selected file Age You can select characters or numbers by pressing VW and press to the next space to edit The maximum is 8 characters without blank any spaces When you are finished press to confirm the new name 9 6 Delete Image You can delete image files from the built in HDD but the source image file cannot be deleted if the file is selected as source Therefore before you delete an image file please check if it is selected as a source and select a new file as the source by 9 1 Selectlmage page 37 Note If an i
27. tion Note In Copy Test Compare and Copy Compare functions 1 If there is no source and target discs inside the duplicator there will be nothing show on LCD 1 LoFs Source Ho 2 If the built in HDD is selected as source the information presents different LLOP x 3 Sources HAGEL Image file name 3 The information display of these 4 functions will be different based on the display mode you selected Please refer to 8 2 Displaymode page 34 5 Set Burn Speed You can adjust the burning speed of CD Audio CD DVD DVD DL Blu ray by this setting The default setting of CD is 40X Audio CD 24X DVD 8X DVD DL 2X and Blu ray 2X 1 Using 4 W to select 5 SetBurn Speed and press er d Sel Burn Speed 2 Pressing 4 W to adjust the burning speed of CD and press ex to confirm it or press ex to select Audio CD DVD DVD DL or Blu ray to adjust the burning speed Burn Epa D da Il Function Introduction 6 Select Source You can set any drive or built in HDD in the duplicator to be your source reader 1 Using to select 6 SelectSource 6 Select Source 2 Press to check the current source reader or select the proper drive to be the source reader by pressing 4 once the source reader is selected press ex to confirm the setting and back to the menu list sources COREL I gt D H1 Note The default setting of source reader is the first drive 7 Utility
28. ustomize audio CD e Copy Track You can select and combine audio tracks from different CDs in this section e Close Disc You have to perform this function after copy track to make the CD playable on CD player e Disc Info You can check the audio CD s information status 7 5 Eject All Disc You can eject all discs including source and target discs at the same time with this function st Il Function Introduction 7 6 Copy Counter This function will record the results of all duplication tasks Show Count You can check how many discs copy successfully and fail Enable Counter You can enable or disable the counter to record the copy results Clear Counter You can delete the record with this function 1 Use A W to select 7 Utility and press to enter the sub menu Then select 6 CopyCounter and press ex CUbilityl E Lors counter 2 Using W to select 1 ShowCount Cory count L Show Count 3 Press to check the calculation of successfully duplicated and failed discs Q ty of passed CD CD Fr Ff Q ty of failed CD DUE P12 Ft 7 7 Update BIOS You can update the systems firmware with this function 1 Place manufacturer certified update file CD into any drive 2 Press 4 W to select 7 Utility and sub menu 7 UpdateBIOS and then press ex to start the process LUtilitu faledate BIOS II Function Introduction 3 The system will automatically detect the update fil
Download Pdf Manuals
Related Search