Hikvision Digital Technology DS-2CC52A1P-AVPIR2 surveillance camera
Contents
1. MIRROR If you turn the MIRROR function on the image will be flipped horizontally It looks like the image in the mirror BRIGHTNESS The brightness is adjustable from 0 to 255 CONTRAST This feature enhances the difference in color and light between parts of an image The value ranges from 0 to 255 SHARPNESS SHARPNESS describes the clarity of detail in the image The value ranges from 0 to 255 HUE Adjust this feature to change the color of the image The value ranges from 0 to 255 GAIN Adjust this feature to change the depth of the color The value ranges from 0 to 255 31 High definition Vandal proof Dome Camera User Manual PICT ADJUST MIRROR OFF BRIGHTNESS 000 CONTRAST SHARPNESS HUE GAIN RETURN Figure 3 7 PICT ADJUST 3 7 ATR Setting ATR is the digital dynamic range function which can adjust the brightness and contrast level of the image and balance the brightness level of the whole image Move the cursor to ATR Set the button left right to select ON or OFF After you set it to ON you can press the menu button to enter the ATR submenu LUMINANCE MID HIGH and LOW are selectable standing for middle high and low luminance respectively CONTRAST MID HIGH LOW MIDLOW and MIDHIGH are selectable 32 High definition Vandal proof Dome Camera User Manual ATR LUMINANCE LOW CONTRAST LOW RETURN Figure 3 8 ATR 3 8 M2. Manual Note Internal synchronization is the default SYNC method Set the menu button to right for about 2 seconds you can switch the SYNC mode to line lock from the SYNC settings Perform the same operation to switch it to internal synchronization from the line lock 3 14 Language Setting This series of camera supports multi language English default Chinese Japanese French Russian Portuguese Spanish and German are selectable Steps 1 Move the cursor to LANGUAGE 2 Set the menu button left right to select the language you need 3 15 Camera Reset Setting Move the cursor to CAMERA RESET and press the menu button to reset all camera settings to the default 3 16 Defective Pixel Correct Settings The CCD sensor of the lens may appear defective pixels You can trigger the defective pixel correction function to correct and compensate the defective pixels Note 42 High definition Vandal proof Dome Camera User Manual The defective pixel correct function may not be displayed on the menu you can enable the function by following the steps below Steps 1 Exit the OSD menu to the live view screen 1 Switch and hold the menu button to the left for 2 seconds until you see the message of COVER UP LENS CLOSE IRIS 2 Cover the lens or close the iris to prevent the light from entering the lens 3 Press the menu button to confirm You will be able to see the bright dot detects on the grainy s
3. W submenu select ON or OFF to enable or disable the color burst function IR OPTIMIZER The camera will calculate the image brightness by the DSP and suppress the IR brightness if the image is overexposed caused by the IR LED B W BURST OFF IR OPTIMIZER OFF MODE LEVEL RETURN Notes Figure 3 12 B W 38 High definition Vandal proof Dome Camera User Manual There is no external triggered output for this series of dome camera Forthe dome cameras which don t support IR the EXT 1 EXT 2 is not supported For the dome cameras which support IR if you select EXT 1 EXT 2 the day mode switches to the night mode automatically at the same time the IR LED turns on 3 11 NR Setting Noise Reduction is used to reduce the noise in the video signal Move the cursor to NR and press confirm to enter the NR submenu Y LEVEL The value ranges from 0 to 15 NR Y LEVEL 004 RETURN Figure 3 13 NR 39 High definition Vandal proof Dome Camera User Manual 3 12 Camera ID Setting On Camera ID submenu you can customize the camera ID It also allows you to adjust the camera ID position on the monitor screen This series of camera supports up to 52 characters Select OFF to disable the Camera ID Select ON to enable the Camera ID Customizing the camera ID Steps 1 Set it to ON and press the menu button to enter the submenu 2 Set the menu button up down left r
4. only shutter and AGC are adjustable In the AUTO SETUP submenu Figure 3 2 you can adjust the BRIGHTNESS value The system will automatically adjust the SHUTTER AGC and AUTO IRIS settings according to the BRIGHTNESS value And the system can define and recognize the luminance level automatically 25 High definition Vandal proof Dome Camera User Manual In HIGH LUMINANCE condition the SHUTTER speed and AUTO IRIS level is modified automatically according to the BRIGHTNESS value MODE SHUT AUTO IRIS and AUTO IRIS are available when the LENS type is AUTO IRIS When the LENS type is Manual the iris is fixed and only SHUT option is provided BRIGHTNESS _ The value ranges from 0 to 255 In LOW LUMINANCE condition the AGC can be adjusted automatically according to the BRIGHTNESS value MODE Only AGC is available BRIGHTNESS x1 00 x0 75 x0 50 and x0 25 are selectable AUTO SETUP HIGH LUMINANCE MODE SHUT AUTO IRIS AUTO IRIS BRIGHTNESS 080 LOW LUMINANCE MODE AGC BRIGHTNESS 0 50 RETURN Figure 3 2 AUTO SETUP 26 High definition Vandal proof Dome Camera User Manual In the MANUAL SETUP submenu it only supports SHUT AGC You can adjust the SHUTTER speed and AGC value to maintain the brightness level of the camera SHUTTER AGC Manually set the shutter speed 1 50 1 120 1 250 1 500 1 1k 1 2k 1 4k and 1 10k are selectable for PAL standard 1 60 1 100 1 250 1 500 1 1
5. the daytime the illumination is high so the iris is adjusted to a small size automatically The DOF depth of field is long But at night the iris is adjusted to a large size automatically so the DOF is shortened The focus you adjusted in the daytime now locates out of the DOF so the image is defocused at night To Solve the Problem When you adjust the focus for a camera with an auto iris lens you need to set the lens type to AES auto electronic shutter mode Under AES mode the iris is adjusted to the largest size automatically Then you can adjust the focus to get a clear image At last you need to set the lens type back to AI auto iris mode Or you can adjust the focus in low illumination condition such as at night Problem 4 Acamera with OSD menu and an auto iris lens displays black video but the OSD menu can be called and displayed Possible Reasons 49 High definition Vandal proof Dome Camera User Manual Auto iris lens connector is loose contact Or the iris driven mode of the camera does not match with the mode of auto iris lens To Solve the Problem Check the auto iris lens connector to ensure good contact Set the iris driven mode of the camera the same as the mode of lens The modes can be VD video drive or DD direct drive DD mode is commonly used Technical Maintenance Lens Maintenance The lens surface is plated an anti reflection coating The dust oil and finger print etc wil
6. to crop the entire image and then digitally enlarge the size of a portion of image that is needed to zoom in on 47 High definition Vandal proof Dome Camera User Manual Troubleshooting Problem 1 Why does the camera restart intermittently And the problem is much more serious when infrared lights of IR camera are turned on at night Possible Reasons The main and common reason is power supply shortage This problem may happen to the IR camera especially at night because the infrared lights are turned on at night and increase the power consumption To Solve the Problem You need to ensure that the power supply matches with 10 of the nominal voltage And the power consumption of power adapter should meet the demand of the camera Problem 2 The camera can never be focused by adjusting the focus stick on the lens And there is also no use adjusting the back focus Possible Reasons The camera needs the lens with CS lens mount When you installa lens with C lens mount the camera will never be focused To Solve the Problem You can change a lens with CS lens mount to the camera 48 High definition Vandal proof Dome Camera User Manual Or you can use a C CS adapter ring between the camera and the lens with C lens mount Problem 3 The camera is installed with an auto iris lens You adjust the focus to get aclear image in the daytime but the image is defocused at night Possible Reasons In
7. HIK VISION High definition Vandal proof Dome Camera User Manual UD 6L0201D0076A01 www hikvision com High definition Vandal proof Dome Camera User Manual Thank you for purchasing our product If there are any questions or requests please do not hes itate to contact the dealer This manual applies to the following modes Model Description DS 2CC5281P N VP 600TVL 1 3 CCD Day Night vari focal weather proof vandal proof dome camera DS 2CC5281P N AVPIR2 600TVL 1 3 CCD IR vari focal weather proof vandal proof dome camera DS 2CC52A1P N VP 7OOTVL 1 3 CCD Day Night vari focal weather proof vandal proof dome camera DS 2CC52A1P N AVPIR2 7OOTVL 1 3 CCD IR vari focal weather proof vandal proof dome camera This manual may contain seve printing errors and the conten The updates will be added to t will readily improve or update described in the manual DISCLAIMER STATEMENT ral technical incorrect places or is subject to change without notice he new version of this manual We the products or procedures Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested for fire shock or casualty hazards 1 High definition Vandal proof Dome Camera User Manual as outlined in UL s Standard s for Safety UL60950 1 UL Certification does not
8. High definition Vandal proof Dome Camera User Manual Figure 2 5 Install the Black Liner and the Lower Dome 10 Remove the protection film softly to complete the installation Note Remove the protection film after the installation is completed in case of the image problem caused by the scrape of the lower dome 2 2 Ceiling Mounting with a gang box Steps 1 Secure the adapter ring to the gang box 13 High definition Vandal proof Dome Camera User Manual Figure 2 6 Secure the Adapter Ring 2 Loosen the screws to open the lower dome 3 Remove the black liner Figure 2 7 Remove the Black Liner 4 Route the cables and connect the power supply and output the video on a monitor 5 Secure the camera to the adapter ring with the screws 14 High definition Vandal proof Dome Camera User Manual Figure 2 8 Install the Camera 6 Adjust the lens 1 View the camera image via the monitor 2 Loosen the lock screw besides the lens 3 Rotate the panning table to adjust the panning position of the camera 0 to 355 is adjustable 4 Rotate the tilting table to adjust the tilting position of the camera 0 to 75 is adjustable 5 Rotate the lens to adjust the azimuth angle of the image 0 to 355 is adjustable 6 Tighten the lock screw 7 Move the focus lever and zoom lever to adjust the focus and the zoom 7 Attach the black liner back to the camera 15 High definiti
9. L mode the iris is set at the maximum value and it is not configurable Selecting AUTO mode press the menu button to enter the AUTO IRIS submenu AUTO IRIS TYPE DC MODE AUTO SPEED 080 RETURN Figure 3 1 AUTO IRIS AUTO IRIS function can automatically adjust the iris according to the changing light conditions TYPE It supports Direct Current Driven DC There is a drive circuit in the camera which can directly output DC control voltage to control electronic motor 24 High definition Vandal proof Dome Camera User Manual MODE AUTO OPEN and CLOSE are selectable for iris mode Selecting auto means the iris is adjusted automatically selecting open means the iris is fully open and selecting close mean the iris is totally closed SPEED Adjust the iris speed The higher the value is the faster the speed of the auto iris is The value ranges from 0 to 255 Note It is recommended that you adjust the iris speed only when the iris vibrates 3 3 Shutter AGC Setting SHUTTER AGC allows you to adjust the way the system balances SHUTTER and AGC settings in different light conditions You can set the different shutter and AGC value according to the luminance level of the situation You can choose MANUAL or AUTO mode for the shutter and AGC Note On the lens setting interface if you choose lens type as AUTO the AUTO IRIS can also be adjusted to change the brightness of the image otherwise
10. comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC High definition Vandal proof Dome Camera User Manual 2002 96 EC WEEE directive Products marked X with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper CE recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info High definition Vandal proof Dome Camera User Manual Table of Contents 1 Introduction 1 1 Product Features MOEA ard La RIISI TISTET ETITI TA TATT 8 2 Installation 9 2 1 Ceiling Mounting 2 2 Ceiling Mounting with a gang box 2 3 Wall Mounting 2 4 Side Conduit Cabling sssessssssssssserrsiserrsrnrrrrerrrsreens 20 255 aal PEIEE ITE ITET TETTEST TTT TTT 21 3 Menu Operations cccssese
11. cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT 0100001021109 High definition Vandal proof Dome Camera User Manual Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied C accessories too are marked with CE and
12. creen 4 After the process the bright dot defects will disappear and you can see SUCCESS on the screen 5 Press the menu button to exit Note An ERROR may occur because that the lens was not fully covered Please repeat above steps to try again 3 17 Save All Exit Move the cursor to the Exit and press the menu button to exit the settings without saving Move the cursor to SAVE ALL and press menu button to save the settings and exit 43 High definition Vandal proof Dome Camera User Manual Glossary Note The glossary gives brief explanations to the basic operation principle or the basic function of the camera However it doesn t mean the listed functions are all supported by this series of camera Please take the actual function in the corresponding specification as the standard Definition Definition is the degree to distinguish the edge between two parts clearly Contrast Contrast is the color difference between the brightest and darkest parts Saturation Saturation is the degree of color purity The color is purer the image is brighter DAY NIGHT Auto Switch The cameras deliver color images during the day And as light diminishes at night the cameras switch to night mode and deliver black and white images with high quality AGC AGC is a control circuit that automatically changes the gain of a receiver or other piece of equipment so that the desired output 44 High defin
13. djust the azimuth angle of the image 0 to 355 is adjustable 6 Tighten the lock screw 18 High definition Vandal proof Dome Camera User Manual 7 Move the focus lever and zoom lever to adjust the focus and the zoom 9 Attach the black liner back to the camera Figure 2 13 Install the Black Liner 10 Attach the lower dome back to the camera and secure it with the screws Figure 2 14 Install the Lower Dome 19 High definition Vandal proof Dome Camera User Manual 11 Remove the protection film softly to complete the installation Note Remove the protection film after the installation is completed in case of the image problem caused by the scrape of the lower dome 2 4 Side Conduit Cabling There are two cabling methods selectable for this series of camera One is to route the cable through the ceiling and the other is to route the cable though the side conduit Steps 1 Unscrew the water proof plug shown below Figure 2 15 Unscrew the Water proof Plug 2 Route the power video cables through the water proof plug to the conduit 20 High definition Vandal proof Dome Camera User Manual 3 Connect the corresponding power video cables 4 Screw the conduit to the water proof plug to complete the installation Figure 2 16 Connect the Conduit to the Camera 2 5 Wiring Figure 2 17 The Power Video Cable Two pins Power Interface 21 High definition Vandal proof Do
14. eeeeseeeeeeeeeseneaeeeeeeeeeeeeseeeensenseasene 3 1 Menu Description 3 2 Lens Settings ta 3 3 Shutter AGC Setting cccccccssseeeesseeeeeeeneeeeeeeeeeeeens 3 4 White Balance Setting 3 5 Backlight Setting 3 6 Picture Adjust Setting a SUZ ATR y PE T T T A 3 8 Motion Detection Setting 3 9 Privacy Mask Setting 3 10 Day Night Setting a AI NR SATUN ascris eaae anaE E Ar A a AEA 12 Camera ID Setting 13 SYNC Setting 14 Language Setting 15 Camera Reset Setting ccecccceeeeeeeeeeeeeeeaeeeeeaaeeee 16 Defective Pixel Correct Settings 17 Save All Exit WWW Wwo wo ww High definition Vandal proof Dome Camera User Manual GIOSSALY AAEE E E E E T ATE E E 44 Troubleshooting Technical Maintenance cccccseeseseeseesseeneeeseeseeeeeseeeneenenenne 50 High definition Vandal proof Dome Camera User Manual 1 Introduction 1 1 Product Features This series of camera adopts high sensitive sensor and advanced circuit board design technology It possesses of high resolution low distortion and low noise features etc It is extremely suitable for surveillance system and image process system The main features are as follows Adopt high performance SONY CCD up to 700TVL resolution providing high definition and clear image OSD menu which enables user to configure the detailed parameters Support Digital Wide Dynamic Range D WDR for backlighting surveillance Au
15. eturn to the MAIN MENU and click SAVE ALL 7 You can find the MONITOR AREA frame take effect after you exit the main menu Note The MONITOR AREA frame takes effect only when the BLOCK DISP panes are included in the MONITOR AREA frame 34 High definition Vandal proof Dome Camera User Manual MOTION DET DETECT SENSE 10 1 BLOCK DISP OFF MONITOR AREA ON AREA SEL 1 4 TOP BUTTOM LEFT RIGHT RETURN Figure 3 9 MOTION DET 3 9 Privacy Mask Setting This feature allows you to cover certain areas which you don t want them to be viewed or recorded Up to 8 privacy areas are configurable Steps 1 Move the cursor to PRIVACY and press menu button to enter the PRIVACY submenu 2 Select one privacy area in AREA SEL 3 Set the values of TOP BOTTOM LEFT and RIGHT The size and the position of the area can be defined by these values 4 Select the color and the transparency values for the privacy area Turn the MOSAIC on if you want to mosaic the privacy areas 5 Repeat the steps 1 to step 4 to configure other privacy areas AREA SEL There are 8 areas available 35 High definition Vandal proof Dome Camera User Manual COLOR There are 8 colors available TRANSP 1 00 0 75 0 50 and 0 00 are selectable PRIVACY AREA SEL TOP BUTTOM LEFT RIGHT COLOR TRANSP MOSAIC RETURN Figure 3 10 PRIVACY Note When the motion detection is on up to 4 p
16. ight to position the cursor on the character you want 3 Press menu button to confirm your selection The selected character displays on the screen 4 Repeat the steps 1 step 3 to select other characters Modifying the camera ID Steps 1 Position the cursor on one of the arrows lt gt TV 2 Press the menu button to position the cursor on the character that needs to be modified 3 Select one of the other characters to replace it Clearing the camera ID Steps 1 Position the cursor on CLR 2 Press the menu button to clear the characters Positioning the camera ID 40 High definition Vandal proof Dome Camera User Manual Steps 1 Move the cursor to POS and press the menu button to enter the position setting interface 2 Set the menu button up down left right to position the camera ID 3 Press the button to save the position and exit CAMERA ID ABCDEFGHIJKLMNOPQRSTUV WXYZ0123456789 amp OL 2 lt gt A x f CIR POS RETURN Figure 3 14 CAMERA ID 3 13 SYNC Setting Both internal and line lock synchronization are available Note Only the camera which supports AC 24 V power has line lock synchronization If 12V DC power supply is applied SYNC mode is internal synchronization and it is not adjustable If 24V AC power supply is applied you can select either internal or line lock synchronization 41 High definition Vandal proof Dome Camera User
17. ition Vandal proof Dome Camera User Manual signal remains essentially When under low illumination AGC will regulate the gain and amplification of the video signal S N ratio It is the ratio of Signal voltage and noise voltage The ratio is larger the effect of noise is less and the image is clearer White Balance White balance is the white rendition function of the camera to adjust the color temperature according to the environment automatically BLC If you focus on an object against strong backlight the object will be too dark to be seen clearly The BLC Backlight Compensation function can compensate light to the object in the front to make it clear but this causes the over exposure of the background where the light is strong SMART IR The SMART IR adopts the smart image processing technique to automatically adjust the brightness curve by detecting multi zone brightness and so as to prevent the over exposure of central point existed in short IR distance conditions Motion Detection In the user defined motion detection surveillance area the moving object can be detected and trigger alarm The sensitive level can be customized according to the environment Privacy Mask 45 High definition Vandal proof Dome Camera User Manual This function allows you to block or mask certain area of a scene thus prevent the personal privacy from recording or live viewing OSD On Screen Display OSD is the texts su
18. k 1 4k and 1 10k are selectable for NTSC standard 6 00 12 00 18 00 24 00 30 00 36 00 42 00 and 44 80 are selectable for the AGC value MANUAL SETUP MODE SHUT AGC SHUTTER 1 50 AGC 6 00 RETURN Figure 3 3 MANUAL SETUP 27 High definition Vandal proof Dome Camera User Manual 3 4 White Balance Setting Move the cursor to the White Balance and select ATW PUSH PUSH LOCK USER1 USER2 ANTI CR and MANUAL by setting the menu button to left right e ATW Auto Tracking White Balance In ATW mode white balance is continuously being adjusted in real time according to the color temperature of the scene illumination SPEED The speed can be set from 0 to 255 DELAY CNT t s the response time when the color temperature changes ATW FRAME t s used to adjust the image size of the ATW image ENVIRONMENT NDOOR and OUTDOOR are selectable ATW SPEED DELAY CNT ATW FRAME x1 00 ENVIRONMENT INDOOR RETURN Figure 3 4 ATW 28 High definition Vandal proof Dome Camera User Manual USER 1 USER2 USER 1 is the indoor mode and it is suitable for the indoor environment B Gain and R Gain are adjustab ie USER 2 is suitable for the fluorescent light environment B Gain and R Gain are adjustable MANUAL USER 1 WB B GAIN 030 R GAIN 2 2 033 RETURN Figure 3 5 USER 1 WB Selecting MANUAL and pressing the button to enter the MANUAL WB sub
19. l Sade Drilling Template for Outdoor Day Night Vandal proof Dome Camera Figure 2 1 The Drill Template 3 Loosen the screws with the supplied L shape screwdriver to open the lower dome 4 Remove the black liner Figure 2 2 Remove the Black Liner 10 High definition Vandal proof Dome Camera User Manual Note If you want to install the camera to the cement ceiling you need to screw 3 expansion screws into the 3 drilled holes first 5 Route the cables and connect the power supply and output the video on a monitor 6 Secure the dome camera to the ceiling with 3 self tapping screws Refer to Figure 2 3 Figure 2 3 Secure the Camera to the Ceiling 7 Adjust the Lens 1 View the camera image via the monitor 2 Loosen the lock screw besides the lens 3 Rotate the panning table to adjust the panning position of the camera 0 to 355 is adjustable 11 High definition Vandal proof Dome Camera User Manual 4 Rotate the tilting table to adjust the tilting position of the camera 0 to 75 is adjustable 5 Rotate the lens to adjust the azimuth angle of the image 0 to 355 is adjustable 6 Tighten the lock screw 7 Move the focus lever and zoom lever to adjust the focus and the zoom Pan Rotation Figure 2 4 Lens Adjustment 8 Attach the black liner back to the camera 9 Attach the lower dome back to the camera and secure it with the screws 12
20. l cause scratch mildewed and performance degraded Please refer to the following method to clean the lens Handling dust Use oil free soft brush or blowing dust ball to clean the dust Handling oil Steps 1 Wipe off the water drop or oil by soft cloth and dry the lens 2 Use oil free cotton cloth or lens clean paper to wipe the lens from center to outside with alcohol or detergent 3 Change the cloth to wipe the lens until the lens is clean Bubble Maintenance of Domes 50 High definition Vandal proof Dome Camera User Manual The bubble is of transparent plastic The dust oil and finger print etc will cause scratch or image blur Please refer to the following method to clean the bubble e Handling dust Use oil free soft brush or blowing dust ball to clean the dust e Handling oil Steps 1 Wipe off the water drop or oil by soft cloth and dry the bubble 2 Use oil free cotton cloth or bubble clean paper to wipe the bubble from center to outside with alcohol or detergent 3 Change the cloth to wipe the bubble until the bubble is clean Glass Maintenance of IR Camera Steps 1 Wipe off the dust water drop or oil by soft cloth and dry the glass 2 Use oil free cotton cloth or glass clean paper to wipe the glass from center to outside with alcohol or detergent 3 Change the cloth to wipe the glass until the glass is clean 51 First Choice for Security Professionals Hikvision Digital Techn
21. me Camera User Manual Notes Please make sure that the power adapter can match with the camera The standard power supply of the camera is 12V DC or 24V AC Please refer to technical specifications for more details Figure 2 18 The Power Video Cable Notes Please make sure that the power adapter can match with the camera The standard power supply of the camera is 12V DC Please refer to technical specifications for more details 22 High definition Vandal proof Dome Camera User Manual 3 Menu Operations 3 1 Menu Description This series of camera supports OSD menu operation and the menu is listed below LENS AUTO MANUAL SHUTTER AGC AUTO MANUAL WHITE BAL ATW PUSH PUSH LOCK USER1 USER2 ANTICR MANUAL BACKLIGHT BLC HLC OFF PICT ADJUST MIRROR BRIGHTNESS CONTRAST SHARPNESS HUE GAIN H ATR LUMINANCE CONTRAST Main f Men u MOTION DET DETECT SENSE BLOCK DISP MONITOR AREA AREA SEL PRIVACY AREA SEL COLOR TRANSP MOSAIC DAY NIGHT AUTO COLOR B W EXT 1 EXT2 NR Y LEVEL CAMERA ID SYNC INT LANGUAGE English Chinese Japanese Fre 23 High definition Vandal proof Dome Camera User Manual nch Russian Portuguese Spanish German CAMERA RESET EXIT SAVE ALL 3 2 Lens Settings Move the cursor to LENS and then set the menu button left right to select MANUAL or AUTO Selecting MANUA
22. menu Customize the LEVEL value on your demand PUSH MANUAL WB LEVEL 064 RETURN Figure 3 6 MANUAL WB 29 High definition Vandal proof Dome Camera User Manual In the PUSH mode the viewed image retains color balance automatically The color in the image balances according to the color temperature PUSH LOCK In the PUSH LOCK mode you can select a scene and manually adjust the white balance and then lock the color temperature It is suitable for the environment which the color temperature slightly changes ANTICR Anti Color Rolling In ANTI CR mode the system suppresses the color rolling under the fluorescent light environment 3 5 Backlight Setting Move the cursor to the BLC and select OFF BLC or HLC by pressing left right button BLC Backlight Compensation If there s a strong backlight the object in front of the backlight appears silhouetted or dark BLC can correct the exposure of the subject But the backlight environment is overexposed HLC Highlight Compensation HLC masks strong light sources that usually flare across a scene This makes it possible to see the detail of the image that would normally be hidden 30 High definition Vandal proof Dome Camera User Manual 3 6 Picture Adjust Setting Move the cursor to PICT ADJUST Press the confirm button to enter the PICT ADJUST submenu MIRROR BRIGHTNESS CONTRAST SHARPNESS HUE and GAIN are adjustable
23. ology Co Ltd All Rights Reserved
24. on Vandal proof Dome Camera User Manual Figure 2 9 Attach the Black Liner 8 Attach the lower dome back to the camera and secure it with the screws Figure 2 10 Install the Lower Dome 9 Remove the protection film softly to complete the installation Note 16 High definition Vandal proof Dome Camera User Manual Remove the protection film after the installation is completed in case of the image problem caused by the scrape of the lower dome 2 3 Wall Mounting Note Please make sure that the wall is strong enough to withstand three times the weight of the camera Steps 1 Drill four expansion screw holes on the wall 2 Secure the mount to the wall with the expansion screws 3 Insert the adapter ring to the mount Figure 2 11 Install the Mount and the Adapter Ring 4 Loosen the screws to open the lower dome 5 Remove the black liner 6 Secure the camera to the adapter ring 17 High definition Vandal proof Dome Camera User Manual Figure 2 12 Install the Camera 7 Route the cables and connect the power supply and output the video on a monitor 8 Adjust the Lens 1 View the camera image via the monitor 2 Loosen the lock screw besides the lens 3 Rotate the panning table to adjust the panning position of the camera 0 to 355 is adjustable 4 Rotate the tilting table to adjust the tilting position of the camera 0 to 75 is adjustable 5 Rotate the lens to a
25. otion Detection Setting There are two kinds of MOTION DET panes BLOCK DISP and MONITOR AREA Two panes can take effect simultaneously BLOCK DISP Steps 1 Move the cursor to MOTION DET and select ON and press the menu button to enter the submenu 2 Position the cursor on DETECT SENSE and set the menu button left right to adjust the sensitivity level 0 to 127 are selectable 3 Position the cursor on BLOCK DISP and set the menu button left right to select ENABLE 4 Press the menu button to enter the setup interface of the detection panes 5 Select ON to enable BLOCK DISP 6 Move the cursor to MONITOR AREA and select ON 33 High definition Vandal proof Dome Camera User Manual 7 Return to the MAIN MENU and click SAVE ALL 8 You can find the BLOCK DISP take effect after you exit the main menu MONITOR AREA Steps 1 Move the cursor to MOTION DET select ON and press the menu button to enter the submenu 2 Position the cursor on DETECT SENSE and set the menu button left right to adjust the sensitivity level 3 Position the cursoron MONITOR AREA Select OFF to disable area motion detection Select ON to enable area motion detection 4 Position the cursor on AREA SEL to select one area There are four areas available 5 Set the values of TOP BOTTOM LEFT and RIGHT The size and position of the area is defined by these values And after you set all this value you can see a frame on the image 6 R
26. perimposed ona screen It can show the menu on the screen Synchronous System Synchronization of the camera usually contains power synchronization and internal synchronization Internal synchronization is realized by the synchronous signal which is generated by the inside crystal oscillator ICR Auto Switch The filter will filter infrared light during the daytime and change to normal filter at night to ensure a high sensitivity and clear image WDR Wide Dynamic Range The wide dynamic range WDR function helps the camera provide clear images even under back light circumstances When there are both very bright and very dark areas simultaneously in the field of view WDR balances the brightness level of the whole image and provide clear images with details EIS Electronic Image Stabilization Electronic image stabilization function can reduce certain ranges of vibration which is caused by the external environment 3D Digital Noise Reduction Comparing with the general 2D digital noise reduction the 3D digital noise reduction function processes the noise initiated by 46 High definition Vandal proof Dome Camera User Manual CCD besides processing the noise in the separated Y video signal and C video signal HLC High Light Compensation The HLC is capable of detecting and reversing the bright spots in the picture such as headlights to black so as to achieve optimum picture quality Digital Zoom Digital zoom helps
27. rivacy areas are configurable 3 10 Day Night Setting Move the cursor to DAY NIGHT and select AUTO COLOR EXT 1 EXT 2 or B W by setting the menu button to left right COLOR mode is used for normal lighting conditions B W mode can increase the sensitivity in low light conditions AUTO Mode Setting 36 High definition Vandal proof Dome Camera User Manual In AUTO mode the day mode and the night mode can switch automatically Steps 1 After moving the cursor to DAY NIGHT set the menu button left right to select AUTO 2 Press menu button to enter the submenu BURST Burst is an analog video composite video signal generated by a video signal generator used to keep the chrominance subcarrier synchronized in a color television signal Select ON or OFF to enable or disable the color burst function DELAYCNT The value ranges from 0 to 255 This value is the delay time before the day night mode switches DAY gt NIGHT The value ranges from 0 to 255 The day mode switches to the night mode when the light condition reaches to the value you select NIGHT DAY The value ranges from 0 to 255 The night mode switches to the day mode when the light condition reaches to the value you select 37 High definition Vandal proof Dome Camera User Manual DAY NIGHT BURST OFF DELAY CNT DAY gt NIGHT NIGHT gt DAY RETURN Figure 3 11 DAY NIGHT B W Mode Setting BURST In the B
28. to white balance with high color rendition High Signal Noise Ratio SNR which brings clear and high quality image Auto electronic shutter control to adapt to the different surveillance environments Auto gain control adaptive brightness Auto iris Support up to 8 configurable privacy masks to ensure your privacy High definition Vandal proof Dome Camera User Manual e Advanced 3 axis design allows this dome camera to be adjusted 0 355 horizontally and 0 75 vertically to meet different mounting requirements 1 2 Overview 0 Figure 1 1 Overview 1 Black Liner 5 Power Cable 2 Lower Dome 6 Video Cable 3 AUX Interface 7 Lens 4 Menu Button 8 Adapter Ring High definition Vandal proof Dome Camera User Manual 2 Installation Before you start Please make sure that the device in the package is in good condition and all the assembly parts are included This series of camera support ceiling mounting ceiling mounting with a gang box wall mounting and side conduit mounting 2 1 Ceiling Mounting Note Please make sure that the ceiling is strong enough to withstand three times the weight of the camera Steps 1 Attach the drill template supplied to the place where you want to fix the camera 2 Drill 3 screw holes and one cable hole if you want to route the cable through the mounting base according to the drill template High definition Vandal proof Dome Camera User Manua
Download Pdf Manuals
Related Search