Home

Hikvision Digital Technology DS-7604NI-SE/P digital video recorder

Contents

1. User Manual of DS 7600NI Series NVR Stay in the Exporting interface until all record files are exported with pop up message Export finished Export finished Figure 7 24 Export Finished 6 Check backup result Note The Player player exe will be exported automatically during record file export USB1 1 E chO1_ 2011062714191 8 850KB File 06 27 2011 19 50 00 E ch01_ 2011062714291 14 165KB File 06 27 2011 19 50 06 E ch0O1_ 2011062714482 13 309KB File 06 27 2011 19 50 12 player exe 608KB File 06 27 2011 19 50 00 New Folder Format Cancel Figure 7 25 Checkup of Video Clips Export Result Using USB Flash Drive 7 2 Managing Backup Devices Management of USB flash drives and USB HDDs 1 Enter Search Result interface of record files Menu gt Export gt Normal Set search condition and click Search button to enter Search Result interface Note At least one channel shall be selected ZJ IP Camera v Dy eee Dee 1D ee 1B 07 05 2013 16 48 08 08 05 2013 00 48 18 All All 07 05 2013 00 00 00 0 7 05 2013 23 59 59 Figure 7 26 Normal Video Search for Backup 103 User Manual of DS 7600NI Series NVR 2 Select record files you want to back up Click Export button to enter Export interface Note At least one record file shall be selected Search result 10 20 2011 11 50 24 15 23 54 1 038 237KB 10 20 2011 15 23 54 16 11 53 399 657KB 10 20 2011 10 33 53 11 17 18 692 336
2. HIKVISION Network Video Recorder User Manual UD 6L0202D1131A01 User Manual of DS 7600NI Series NVR Hikvision Network Digital Video Recorder User Manual This manual as well as the software described in it is furnished under license and may be used or copied only in accordance with the terms of such license The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Hikvision Digital Technology Co Ltd Hikvision Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book Except as permitted by such license no part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical recording or otherwise without the prior written permission of Hikvision HIKVISION MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE REGARDING THE HIKVISION SOFTWARE HIKVISION DOES NOT WARRANT GUARANTEE OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS ACCURACY RELIABILITY CURRENTNESS OR OTHERWISE THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE HIKVISION SOFTWARE IS ASSUMED BY YOU THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY SOME ST
3. Figure 13 9 Edit User Interface 4 Edit the user information including user name password level and MAC address Check the checkbox of Change Password if you want to change the password of the current user 5 Click the OK button to save the settings and exit the menu 177 User Manual of DS 7600NI Series NVR Appendix 178 User Manual of DS 7600NI Series NVR Glossary Dual Stream Dual stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network The two streams are generated by the DVR with the main stream having a maximum resolution of 4CIF and the sub stream having a maximum resolution of CIF e HDD Acronym for Hard Disk Drive A storage medium which stores digitally encoded data on platters with magnetic surfaces DHCP Dynamic Host Configuration Protocol DHCP is a network application protocol used by devices DHCP clients to obtain configuration information for operation in an Internet Protocol network e HTTP Acronym for Hypertext Transfer Protocol A protocol to transfer hypertext request and information between servers and browsers over a network e PPPoE PPPoE Point to Point Protocol over Ethernet is a network protocol for encapsulating Point to Point Protocol PPP frames inside Ethernet frames It is used mainly with ADSL services where individual users connect to the ADSL transceiver modem over Ethernet and in plain Metro Ethernet
4. Cancel Figure 8 13 Set Arming Schedule of Video Tampering 4 Select Linkage Action tab to set up alarm response actions of video tampering alarm please refer to Chapter Setting Alarm Response Actions Repeat the above steps to set up arming schedule of other days of a week You can also use Copy button to copy an arming schedule to other days 5 Click the OK button to complete the video tampering settings of the channel 116 User Manual of DS 7600NI Series NVR 8 5 Handling Exceptions Alarm Purpose Exception settings refer to the handling method of various exceptions e g HDD Full The HDD is full HDD Error Writing HDD error or unformatted HDD Network Disconnected Disconnected network cable IP Conflicted Duplicated IP address Illegal Login Incorrect user ID or password Record Exception No space for saving recorded files Steps Enter Exception interface of System Configuration and handle various exceptions Menu gt Configuration gt Exceptions Please refer to Chapter Setting Alarm Response Actions for detailed alarm response actions Figure 8 14 Exceptions Setup Interface 117 User Manual of DS 7600NI Series NVR 8 6 Setting Alarm Response Actions Purpose Alarm response actions will be activated when an alarm or exception occurs including Full Screen Monitoring Audible Warning buzzer Notify Surveillance Center Trigger Alarm Output and Send Email Full Screen Moni
5. INFO Button Reserved VOIP Button Switch between main and spot output In PTZ Control mode it can be used to zoom out the image MENU Button Press the button will help you return to the Main menu after successful login Press and hold the button for 5 seconds will turn off audible key beep In PTZ Control mode the MENU WIPER button will start wiper if applicable In Playback mode it is used to show hide the control interface PREV Button Switch between single screen and multi screen mode In PTZ Control mode it is used to adjust the focus in conjunction with the A FOCUS button N DIRECTION Button Navigate between different fields and items in menus In the Playback mode the Up and Down button is used to speed up and slow down recorded video The Left and Right button will select the next and previous record files In Live View mode these buttons can be used to cycle through channels In PTZ control mode it can control the movement of the PTZ camera ENTER Button Confirm selection in any of the menu modes It can also be used to tick checkbox fields In Playback mode it can be used to play or pause the video In single frame Playback mode pressing the button will advance the video by a single frame In Auto switch mode it can be used to stop start auto switch Back to the previous menu Press for Arming disarming the device in Live View mode Reserved for futur
6. Settings Trigger Channel Linkage Action lt Mon 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e e ee606 86 Figure 8 3 Set Arming Schedule of Motion Detection 5 Click Linkage Action tab to set up alarm response actions of motion alarm please refer to Chapter Setting Alarm Response Actions Repeat the above steps to set up arming schedule of other days of a week You can also use Copy button to copy an arming schedule to other days 6 Click the OK button to complete the motion detection settings of the channel 109 User Manual of DS 7600NI Series NVR 8 2 Setting Sensor Alarms Purpose Set parameters and handling action of an external sensor alarm Steps 1 Enter Alarm Settings of System Configuration and select an alarm input Menu gt Configuration gt Alarm Select Alarm Input tab to enter Alarm Input Settings interface Alarm Input Alarm Output Alarm Input List Alarm Input No Alarm Name Alarm Type 172 6 23 105 8000 lt 1 N O Alarm Output List Alarm Output No Alarm Name Dwell Time 172 6 23 105 8000 gt 1 5S Figure 8 4 Alarm Status Interface of System Configuration 2 Set up the handling action of the selected alarm input Check the Enable checkbox and click button to set up its alarm response actions Alarm Status Alarm Output Alarm Input No 172 6 23 105 8000 lt 1 Alarm Name Type Figure 8 5 Alarm Input Setup Int
7. 2 Click Apply and then in the pop up message box click Yes to save your settings 3 Click OK to back to the upper level menu Repeat the above steps to configure more HDD groups 5 Choose the Channels which you want to save the record files in the HDD group 1 Select Advanced on the left bar 2 Choose Group number in the dropdown list of Record on HDD Group 3 Check the channels you want to save in this group 4 Click Apply to save settings Note After having configured the HDD groups you can configure the recording settings following the procedure provided in Chapter 5 2 5 7 71 User Manual of DS 7600NI Series NVR 5 9 Files Protection Purpose You can lock the recorded files or set the HDD property to Read only to protect the record files from being overwritten Protect file by locking the record files Steps 1 Enter Playback setting interface Menu gt Playback MiP Camera O2D1 g D2 g D3 g D4 g D5 g D6 gB D7 Ds g D9 g D10 viDEK g D12 v IDHE D114 v ADRES g D16 06 07 2012 17 21 38 06 12 2012 17 30 08 All All 06 05 2012 00 00 00 06 18 2012 23 59 59 Figure 5 27 Playback 2 Select the channels you want to investigate by checking the checkbox to aa 3 Configure the record type file type start end time 4 Click Search to show the results Search result D3 06 01 2012 00 45 37 01 53 00 1 038 403 D3 06 01 2012 01 53 00 03 00 31 1 038 074 D3 06 01 2012 03 00 31 04 07 59 1 038 478
8. 2 If the HDD mode is Quota please set the maximum record capacity For detailed information see Chapter Configuring Quota Mode 3 If the HDD mode is Group you should set the HDD group For detailed information see Chapter Configuring HDD Group for Recording IP Camera Figure 5 2 HDD Advanced Steps 1 Enter the Record settings interface to configure the recording parameters Menu gt Record gt Parameters IP Camera 1 Main Stream Continuous Video amp Audio 704 576 4CIF Variable Medium Full Frame General 2048 1152 1920 Kbps 5s Figure 5 3 Recording Parameters 57 User Manual of DS 7600NI Series NVR 2 Parameters Setting for Recording 1 Select Record tab page to configure You can configure the stream type the resolution and other parameters on your demand Pre record The time you set to record before the scheduled time or event For example when an alarm triggered the recording at 10 00 if you set the pre record time as 5 seconds the camera records it at 9 59 55 Post record The time you set to record after the event or the scheduled time For example when an alarm triggered the recording ends at 11 00 if you set the post record time as 5 seconds it records till 11 00 05 Expired Time The expired time is the longest time for a record file to be kept in the HDD if the deadline is reached the file will be deleted You can set the expired time to 0 and then the file will not be
9. D3 06 01 2012 04 07 59 05 15 10 1 038 199 D3 06 01 2012 05 15 10 06 27 54 1 038 350 D3 06 01 2012 06 27 54 07 35 55 1 038 400 D3 06 01 2012 07 35 55 08 42 41 1 038 046 D3 06 01 2012 08 42 41 09 49 31 1 038 089 OOK OOO TOON GC D3 06 01 2012 09 49 31 10 56 41 1 038 029 D3 06 01 2012 10 56 41 10 58 17 23 986KB D3 06 01 2012 10 58 18 12 04 06 1 014 225 Start time 05 31 2012 23 38 37 D3 06 01 2012 12 04 06 13 11 12 1 038 197 D3 06 01 2012 13 11 12 14 18 13 1 038 418 End time D3 06 01 2012 14 18 13 14 51 11 509 379KB 06 01 2012 00 45 37 oe nna na nnan nn ne n nn e ana et AA Total 18 P 1 1 HDD 5 DAEL Cancel Figure 5 28 Playback Search Result 5 Protect the record files 1 Find the record files you want to protect and then click the icon which will turn too indicating that the file is locked Note The record files of which the recording is still not completed can t be locked 2 Click a to change it to to unlock the file and the file is not protected 72 User Manual of DS 7600NI Series NVR Attention Record file may be overwritten after unlocking Continue Yes Figure 5 29 Unlocking Attention Protect file by setting HDD property to Read only Steps 1 Enter HDD setting interface Menu gt HDD Figure 5 30 HDD General 2 Click LA to edit the HDD you want to protect Local HDD Settings HDD Ni HDD Property O RAV
10. IP confliction abnormal record HDD error and HDD full etc Alarm triggers full screen monitoring audio alarm notifying surveillance center sending email and alarm output Automatic restore when system is abnormal Other Local Functions Operable by mouse and remote control Three level user management admin user is allowed to create many operating accounts and define their operating permission which includes the limit to access any channel Operation alarm exceptions and log recording and searching Manually triggering and clearing alarms Import and export of device configuration information Network Functions 1 self adaptive 10OM 100M 1000M network interface Up to 8 independent PoE network interfaces for DS 7600NI SE P series and 4 independent PoE network interfaces for DS 7600NI VP series Up to 8 independent network interfaces with built in switch function are provided for DS 7600NI SE N series Pv6 is supported TCP IP protocol PPPoE DHCP DNS DDNS NTP SADP SMTP SNMP NES and iSCSI are supported TCP UDP and RTP for unicast Auto Manual port mapping by UPnP Remote web browser access by HTTPS ensures high security Remote reverse playback via RTSP Support accessing by the platform via ONVIF Remote search playback download locking and unlocking of the record files and support downloading files broken transfer resume Remote parameters setup remote impor
11. b The motion detection and alarm functions are enabled and the parameters of Main Stream Normal and Main Stream Event are different So the image looks stuck due to the image changes between different resolutions c The frame rate is not the real time frame rate d The NVR supports up to 16 channel synchronize playback at the resolution of 4CIF if you want a 16 channel synchronize playback at the resolution of 720p the frame extracting may occur which leads to a slight stuck Steps 1 Verify the network between NVR and IPC is connected 1 When image is stuck connect the RS 232 ports on PC and the rear panel of NVR with the RS 232 cable 2 Open the Super Terminal and execute the command of ping 792 168 0 0 1 1472 f the IP address may change according to the real condition and check if there exists packet loss Note Simultaneously press the Ctrl and C to exit the ping command 2 Check the parameters of Main Stream Normal and Main Stream Event Select Menu gt Record gt Parameters gt Record and set the resolution of Main Stream Event the same as the one of Main Stream Normal 3 Verify the frame rate is real time frame rate Select Menu gt Record gt Parameters gt Record and set the Frame Rate to Full Frame 4 Verify the hardware can afford the playback Reduce the channel number of playback Select Menu gt Record gt Parameters gt Record and set the resolution
12. joje jra Sage jeialo e 4 Pattern gt Gg Patrol2 6 Patrol3 6 Patrol4 Or Figure 4 9 PTZ Toolbar Patrol 4 2 5 Customizing Patterns Purpose Patterns can be set by recording the movement of the PTZ You can call the pattern to make the PTZ movement according to the predefined path Steps 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings 2 Choose pattern number in the option box General IP Camera 3 O Save Preset ee ae ae ae alti uie aa ile as las y ES TETS TO TE SE Call Preset 3 Pattern 1 ooo Patrol 1 Figure 4 10 PTZ Pattern 3 Click and use your mouse to drag the image or click the eight directional buttons in the control box under the image to move the PTZ camera The movement of the PTZ is recorded as the pattern 53 User Manual of DS 7600NI Series NVR 4 Click E to save the pattern 4 2 6 Calling Patterns Purpose Follow the procedure to move the PTZ camera according to the predefined patterns Calling pattern in the PTZ setting interface Steps 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings 2 Select the pattern number 3 Click ol then the PTZ moves according to the pattern Click o to stop it Call pattern in live view mode Steps 1 In the live view mode press PTZ control on the front panel or on the remote control or click PTZ Control icon a on the quick setting toolbar 2 And th
13. 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement CE This product and if applicable the supplied accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info User Manual of DS 7600NI Series NVR Preventive and Cautionary Tips Before connecting and operating your device please be advised of the following tips Ensure unit is installed in a well ventilated dust free
14. 20 Holiday Settings 2 Enable Edit Holiday schedule 1 Click A to enter the Edit interface Holiday1 v By Date 06 23 2011 06 23 2011 Figure 5 21 Edit Holiday Settings 2 Check the checkbox after Enable Holiday 67 User Manual of DS 7600NI Series NVR 3 Select Mode from the dropdown list There are three different modes for the date format to configure holiday schedule 4 Set the start and end date 5 Click Apply to save settings 6 Click OK to exit the Edit interface 3 Enter Record Schedule settings interface to edit the holiday recording schedule See Chapter 6 2 Configuring Record Schedule 68 User Manual of DS 7600NI Series NVR 5 7 Configuring Redundant Recording Purpose Enabling redundant recording which means saving the record files not only in the R W HDD but also in the redundant HDD will effectively enhance the data safety and reliability Steps 1 Enter HDD Information interface Menu gt HDD Figure 5 22 HDD General 2 Select the HDD and click LA to enter the Local HDD Settings interface 1 Set the HDD property to Redundancy Local HDD Settings HDD No HDD Property RN Read only O Redundancy Group REE PEE FEE CEE FEE LEE EEE F EEE BLUE DIE rS EFE DCE EFE Bile 76 319MB Cancel Figure 5 23 HDD General Editing 2 Click Apply to save the settings 3 Click OK to back to the upper level menu Note You must set the Storage mode in the HDD adva
15. 26 MB File 280MB File 4 423KB File 2 TMB File 110MB File 18 36 KB File 06 23 2011 20 07 22 06 23 2011 20 07 28 06 23 2011 20 07 53 06 23 2011 20 07 36 06 23 2011 20 15 02 06 23 2011 20 11 14 06 23 2011 20 11 20 06 23 20 20 12 06 23 2011 20 12 54 06 23 2011 20 13 02 OOOO TORE eC 06 23 2011 20 13 12 06 23 2011 20 09 40 mL 14 37 305KB File 608KB File isnot E chO3_20110623134743 B player exe lt Ph men dees HH nm YONA A 44 3 AL lt whe ewe ew bs os oe d O 9 9 New Folder Format Cancel Figure 7 20 Checkup of Event Export Result Using USB Flash Drive 7 1 4 Backing up Video Clips Purpose You may also select video clips to export directly during Playback using USB devices USB flash drives USB HDDs USB writer or SATA writer Steps 1 Enter Playback interface Please refer to Chapter 6 1 Playing Back Record Files 2 During playback use buttons and in the playback toolbar to start or stop clipping record file s 3 Quit Playback interface after finishing clipping and you will then be prompted to save the clips Note A maximum of 30 clips can be selected for each channel 101 User Manual of DS 7600NI Series NVR Normal camera iPCamera 01 iPCamera 02 iPCamera 03 MiCamera01 iPCamera 05 ee MiPCamera 06 MIPCamera 08 iPCamera 09 S a iPCamera 10 iPCamera 11 iPCamera 12 iPCamera 13 04 25 2013 10 00 12 04 25 2013 16 02 59 wu Aw qm a Mine
16. 35 19 Clear All C Clear Zone 1 Clear Zone 2 Clear Zone 3 Clear Zone 4 Figure 11 2 Privacy Mask Settings Interface 4 Use the mouse to draw a zone on the window The zones will be marked with different frame colors Note Up to 4 privacy masks zones can be configured and the size of each area can be adjusted 5 The configured privacy mask zones on the window can be cleared by clicking the corresponding Clear Zone 1 4 icons on the right side of the window or click Clear All to clear all zones IP Camera 1 01 01 2010 Fri 11 55 19 Clear All _ Clear Zone 1 Clear Zone 2 Clear Zone 3 Clear Zone 4 Figure 11 3 Set Privacy Mask Area 6 Click the Apply button to save the settings 156 User Manual of DS 7600NI Series NVR 11 3 Configuring Video Parameters Steps 1 Enter the Image Settings interface Menu gt Camera gt Image IP Camera 3 Customize Figure 11 4 Image Settings Interface 2 Select the camera to set image parameters 3 You can click on the arrow to change the value of each parameter 4 Click the Apply button to save the settings 157 User Manual of DS 7600NI Series NVR Chapter 12 NVR Management and Maintenance 158 User Manual of DS 7600NI Series NVR 12 1 Viewing System Information 12 1 1 Viewing Device Information Steps 1 Enter the System Information interface Menu gt Maintenance gt System Info 2 Click the Device Info tab to enter the De
17. 6 2 Auxiliary Functions of Playback 6 2 1 Playing Back Frame by Frame Purpose Play video files frame by frame in case of checking image details of the video when abnormal events happen Steps Go to Playback interface If you choose playback of the record file click button EET until the speed changes to Single frame and one click on the playback screen represents playback of one frame If you choose adverse playback of the record file click button EEE until the speed changes to Single frame and one click on the playback screen represents adverse playback of one frame It is also feasible to use button g in toolbar 6 2 2 Smart Search Purpose In order to locate motion detection event easily and accurately in the playback progress bar you are allowed to analyze a certain area scene dynamically and to get all of the related motion detection events that occurred in this area Note The smart search function varies according to the camera connected to the NVR Before you start 1 Log in the network camera by the web browser and enable the Dynamic Analysis for Motion by checking the checkbox of it You may enter the motion detection configuration interface by Configuration gt Advanced Configuration gt Events gt Motion Detection Motion Detection Tamper proof Exception Email Snapshot Other Alarm Enable Motion Detection Enable Dynamic Analysis for Motion 2 Enable the motion detection function and set the arming area
18. 931 51GB Normal RIW Local 890GB 1 Z E 931 51GB Normal RAW Local 867GB 1 A ars 9 S68MB Normal RAW NAS 79 8 72MB 1 A Figure 10 9 Initialize Added NetHDD 143 User Manual of DS 7600NI Series NVR 10 3 Managing HDD Group 10 3 1 Setting HDD Groups Purpose Multiple HDDs can be managed in groups Video from specified channels can be recorded onto a particular HDD group through HDD settings Steps 1 Enter the Storage Mode interface Menu gt HDD gt Advanced 2 Set the Mode to Group as shown in Figure 10 10 1 M01 D2 EBD D4 EDS EBD ODF MDS PEES PI DES MD11 Pir MD13 MD14 MD15 MD16 Figure 10 10 Storage Mode Interface 3 Click the Apply button and the following Attention box will pop up Attention Reboot to take effect of the changing of the storage mode Continue No Figure 10 11 Attention for Reboot 4 Click the Yes button to reboot the device to activate the changes 5 After reboot of device enter the HDD Information interface Menu gt HDD gt General 6 Select HDD from the list and click LA icon to enter the Local HDD Settings interface as shown in Figure 10 12 144 User Manual of DS 7600NI Series NVR Local HDD Settings HDD Property Oo RAW Read only Redundancy Group SERYE ee Lee ee L bee T EEE DUE DIE ea DES ECE em Bi 931GB Cancel Figure 10 12 Local HDD Settings Interface 7 Select the Group number for the current HDD Note The default group No f
19. Before you start Connect the network cameras via the built in switch interfaces Steps 1 Enter the Camera Management interface Main menu gt Camera gt Camera You can see the connected cameras are listed Cam Add De Status IP Camera A Edit Camera Name Protocol Device Model D1 192 168 254 2 IPCamera01 HIKVISION D2 192 168 254 3 IPCamera02 HIKVISION BE 192 168 254 4 IPCamera 03 HIKVISION D4 192 168 254 5 IPCamera 04 HIKVISION D5 i 192 168 254 6 IPCamera 05 HIKVISION D6 192 168 254 7 IPCamera 06 HIKVISION D 192 168 254 8 IPCamera 07 HIKVISION D8 192 168 254 9 IPCamera 08 HIKVISION Figure 2 26 Camera List Note The cameras connecting to the built in switch interface cannot be deleted in this menu 37 User Manual of DS 7600NI Series NVR 2 Click the button and select the Adding Method in the drop down list Plug and Play It means that the camera is connected to the built in switch interface so in this case the parameters of the camera can t be edited The IP address of the camera can only be edited in the Network Configuration interface see Chapter 9 1 Configuring General Settings for detailed information Edit IP Camera IP Camera No D1 Adding Method Plug and Play IP Camera Address 12 168 254 2 Protocol HIK VISION Manage Port 8000 Channel No 1 User Name Admin Password Cancel Figure 2 27 Edit IP Camera Interface Plug and Play Manual You can
20. Detailed eae of Playback by time Interface Audio on Start Stop i ans 30s forward 30s reverse Mute clipping Add default Tag Speed down tag management Pause reverse Pause play play Scaling Play Reverse play up down the Speed up Single frame Single frame time line play reverse play fms roe Cd Note Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames 6 1 3 Playing Back by Event Search Purpose Play back record files on one or several channels searched out by restricting event type e g alarm input and motion detection Steps 1 Enter the Playback interface Menu gt Playback 2 Select the Event in the drop down list on the top left side 3 Select Alarm Input or Motion as the event type edit the Start time and End time 78 User Manual of DS 7600NI Series NVR E Event x Type Alarm Inpt KAlarm Input No 172 6 23 126 8000 Start Time 2013 07 11 00 00 00 End Time 2013 07 11 23 59 59 Q Search Figure 6 8 Alarm Input Search Interface B Event Type Motion Camera E Camera 01 Camera02 WPCamera 03 E iPCamera 04 E iPCamera 05 iPCamera 06 Camera 07 PCamera 08 iPCamera 09 iPCamera 10 E iPCamera 11 PCamera 12 PCamera 13 PCamera 14 PCamera 15 E iPCamera 16 Start Time 12 11 2012 00 00 00 End Time 12 11 2012 23 59 59 Q Search Figure 6 9 Motion Search Interface 4 Click Sea
21. Local Upgrade Figure 12 13 FTP Upgrade Interface 3 Enter the FTP Server Address in the text field 4 Click the Upgrade button to start upgrading 5 After the upgrading is complete reboot the NVR to activate the new firmware 167 User Manual of DS 7600NI Series NVR 12 5 Restoring Default Settings Steps 1 Enter the Default interface Menu gt Maintenance gt Default System will restore factory settings after reboot Continue Figure 12 14 Restore Factory Default 2 Click the OK button to restore the default settings Note Except the network parameters including IP address subnet mask gateway MTU default route and server port all other parameters of the device will be restored to factory default settings 168 User Manual of DS 7600NI Series NVR Chapter 13 Others 169 User Manual of DS 7600NI Series NVR 13 1 Configuring General Settings Purpose You can configure the output resolution system time mouse pointer speed through the Menu gt Configuration gt General interface Steps 1 Enter the General Settings interface Menu gt Configuration gt General 2 Select the General tab DST Settings More Settings Language English Resolution 1024 768 60HZ Time Zone GMT 08 00 Beijing Urumai Singapore Date Format DD MM YYYY System Date 08 06 2013 system Time 15 17 05 Mouse Pointer Speed Enable Wizard a Enable Passwore fea Figure 13 1 General Settings In
22. PS 11 5 7 8 10 1 2 6 3 4 Figure 1 8 DS 7604 amp 7608NI SE P 9 Pie ie it 1 E Bann s0005 je a VFL Se LAR S We lt orm GA AUDIp OUT LAN Rfaas em 11 5 7 8 10 1 2 6 3 4 Figure 1 9 DS 7616NI SE P LAN Network Interface Connector for LAN Local Area Network RS 485 Interface Connects to RS 485 devices Power Supply 100 240VAC power supply Power Switch Switch for turning on off the device Universal Serial Bus USB ports for additional devices such as USB 5 USB Interface mouse and USB Hard Disk Drive HDD 6e Gn Ground needs to be connected when NVR starts up HDMI Interface HDMI video output connector naa VGA Output DB9 connector for VGA output Display local video output and menu RCA connector for voice talk input Audio Out RCA connector for audio output Network interfaces with PoE function Network interface for the cameras and to provide power over Ethernet for DS 7600NI SE P O O09 Oo000 0 LO OD O O ozo Q CRES O oo O OQO O re o O O 0 e O O Figure 1 8 DS 7600NI V Figure 1 9 DS 7600NI VP Power Switch Switch for turning on off the device 21 User Manual of DS 7600NI Series NVR LAN Network Interface Connector for LAN Local Area Network RCA connector for voice talk input Ground needs to be connected when NVR starts up Audio Out RCA connector for audio output e H
23. Soft Keyboard Description of the buttons on the soft keyboard Table 1 5 Description of the Soft Keyboard Icons oy English Ta Capital English E covcreasertppercse MM Backspace EO w 0 19 User Manual of DS 7600NI Series NVR 1 5 Rear Panel 9 4 wh IN j j O fo Ss QAO 5 5 7 8 10 1 3 2 Figure 1 5 DS 7604 amp 7608NI SE fy fh ra f v ZEN a cy Ss eH Lj E 1 2 3 4 fom VGA nvorpovr LAN S inf F 2 11 5 7 8 10 1 3 gt pm Figure 1 6 DS 7604NI SE N 9 4 y OOA V ae amp Lhe 11 5 7 8 10 1 2 3 6 Figure 1 7 DS 7608 amp 7616NI SE N Table 1 6 Description of Rear Panel Interfaces LAN Interfaces Connector for LAN Local Area Network RS 485 Interface Connector for RS 485 devices Power Supply 12VDC power supply Power Switch Switch for turning on off the device E E T A 6 Gromd Ground needs to be connected when NVR starts up HDMI HDMI video output connector DB9 connector for VGA output Display local video output and menu 9 AUDIO IN BNC connector for audio input Also for two way audio AUDIO OUT BNC connector for audio output Network interfaces with built in switch function Independent 10 100 Mbps PoE Ethernet interfaces for DS 7600NI SE N 20 User Manual of DS 7600NI Series NVR 9 f mT OOo s e CAM 1 ei om GA AUDID OUT can
24. Wile RECOLG TOOMA Oe n O eis aiaas deetuess cuentas waaines cenaigs 159 12 1 4 Viewing Alarm Information ccccccceccccccccceeceeeessseseeeeccccceeeeeaeaeessseseeeeeceeeeeess 160 12 1 5 Viewine Network Information social r E E 160 12 1 6 View ine HDD Informit On senini ine ceeds EAE E 161 2 2 Se arcmin ene Export LoS Fleiner e anaes haba ea beeen 161 12 3 Importing Exporting Configuration Files siseses ree E e E ENEE E EEEa Ek 165 ae MN OB 6 T Ra E 9 EE E EE E ETE EA E AE E OE O EA 166 12 4 1 Upsrading by Local Backup Device sscrieisiutosrnnoai e E 166 12 4 2 Op eE T A AE EE PE EE E T EEEE EAE E AAAS Tete Teen AE AER 166 12 53 Restoring Deriul Setini Sss E E A E T E 168 Chapter 13 OHOL S oien E cede daneeneueusedccds 169 PA Conhsurine eneral Seine S onii n E i be tetatedayasaedoetaaeenbcamieaserecns 170 E2 Conieonns DST Sena Saa N 171 13 3 Configuring More Settings for Device Parameters ccccccccccccsssssssessseeceececeeeceeeaaaaaeeeseeseeees 172 PDA Manase User ACCO IS nnen a a a a a E 173 13 4 1 Add me TUSE ea N AEE ERER EARE 173 11 User Manual of DS 7600NI Series NVR 13 4 2 Deen AAU eE on i taeaehs ab eitaends adie A 176 13 4 3 Edna SET oat fel alecuessileahat clan cedhvastosh a dantoade solos E ted RES 176 PRCT sarina cacsieseiccovecevecstacuuagsvesecaesssctececbunetassdusviceaseneccestessacnseesedccesesbeceanodecensseseacecesteveces 178 GOSS ALY cscs E E E N a core award aa E iota rupees E ar nset
25. and Packet LOSS icuiuicisourausainauaaeualaiunivmelabciets 136 9 4 2 Exportine Network PACK CU ecni idasi E E 136 9 4 3 Checkins the Network Stassen a a a a 137 9 4 4 Checking Network Statist is caccsn ccccusesiscntiiciucnsiailenclawsd beset linceasudiscndedendeuntnCacbecdedces 138 Chapter 10 HDD Wana 8 ement orenen S AEE EE E 139 O Mitalizme HDDS ar E E E E T T E E 140 10 2 Maniacs Netwoti HD Derd E sitastadectavesn staiselndurn ees eet id etaeateliaies 142 LOS Manasme HDD Groupes Dateien ea ciechcccsia a a i a bi litin ou ttnctle peauealevoes 144 10 3 1 See HDO COUPS eee a a a cialat teenth latest ee teits ables 144 10 3 2 SEME HDIXPrODE siie a T rece Adabice whe sensnis 145 LOA JC onmennne Quota ModE ien a a a a ened eee cuenies 147 POD Checkit HDD Statt Sera e A dd led E E E 149 106 HDD E CUO aa N a A S 151 LO Conficoin HDD Error Alarms ssanie na e a E R E A E E N 153 Chapter 11 Camera CCU INS orense AEEA A A a 154 ILI Conieunns OSD Setini Seri E E A E E R E 155 H2 Conie ume AE IV AC y Maie a a ananeraraseereenacate abaans 156 Ho Confiserie Video Paramete simetre E E E E ETE 157 Chapter 12 NVR Management and Maintenance 0ccccsssssscccssssscsssssssccsssssscccccssscccsssssccssssssooooes 158 2P Viewme System Information sene ences ccccanilewceuslaccendsles EA E a eA 159 12 1 1 Viewine Device Informa Ohna A A EA 159 12 1 2 Viewin Camera MMOrmMalOn scescrsioessessusshcxaicearstuseeth tsicsaoecteahuadiceantumatencacentvns 159 12 1 3 Vie
26. and bitrate to a lower level 5 Reduce the number of local playback channel Select Menu gt Playback and uncheck the checkbox of unnecessary channels 6 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from Hikvision to do the further process No record file found in the NVR local HDD and prompt No record file found Possible Reasons a The time setting of system is incorrect b The search condition is incorrect c The HDD is error or not detected Steps 1 Verify the system time setting is correct 184 User Manual of DS 7600NI Series NVR Select Menu gt Configuration gt General gt General and verify the Device Time is correct 2 Verify the search condition is correct Select Playback and verify the channel and time are correct 3 Verify the HDD status is normal Select Menu gt HDD gt General to view the HDD status and verify the HDD is detected and can be read and written normally 4 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from Hikvision to do the further process 185 User Manual of DS 7600NI Series NVR Summary of Changes Version 2 3 4 Added 1 Support adding IP cameras by the right click menu Chapter 2 3 1 2 Support smart search function Chapter 6 2 2 3 Support connecting the third party netw
27. and encoders Connectable to the third party network cameras like AXIS Brickcom Bosch PANASONIC SAMSUNG and SANYO and network cameras that adopt ONVIF or PSIA protocol PAL NTSC adaptive video inputs Each channel supports dual stream Up to 16 network cameras can be connected Independent configuration for each channel including resolution frame rate bit rate image quality etc The quality of the input and output record is configurable Local Monitoring Simultaneous HDMI and VGA outputs HDMI output and VGA output at up to 1920x1080 resolution Multiple screen display in live view is supported and the display sequence of channels is adjustable Live view screen can be switched in group and manual switch and automatic cycle live view are also provided and the interval of automatic cycle can be adjusted Quick setting menu is provided for live view Motion detection video tampering video exception alert and video loss alert functions Privacy mask Multiple PTZ protocols supported PTZ preset patrol and pattern Zooming in by clicking the mouse and PTZ tracing by dragging mouse HDD Management Up to 2 SATA hard disks can be connected Each disk with a maximum of 4TB storage capacity 8 network disks 8 NAS disks or 7 NAS disks 1 IP SAN disk can be connected Support S M A R T and bad sector detection HDD group management Support HDD standby function HDD property redundancy read only read write R
28. below 5 Click the Apply button to save the settings 153 User Manual of DS 7600NI Series NVR Chapter 11 Camera Settings 154 User Manual of DS 7600NI Series NVR 11 1 Configuring OSD Settings Purpose You can configure the OSD On screen Display settings for the camera including date time camera name etc Steps 1 Enter the OSD Configuration interface Menu gt Camera gt OSD 2 Select the camera to configure OSD settings 3 Edit the Camera Name in the text field 4 Configure the Display Name Display Date and Display Week by clicking the checkbox 5 Select the Date Format Time Format and Display Mode IP Camera 1 Camera01 MM DD YYYY 24 hour le Non Transparent amp Not Flashing 01 01 2010 Fri 11 99 19 Figure 11 1 OSD Configuration Interface 6 You can use the mouse to click and drag the text frame on the preview window to adjust the OSD position 7 Click the Apply button to apply the settings 155 User Manual of DS 7600NI Series NVR 11 2 Configuring Privacy Mask Purpose You are allowed to configure the four sided privacy mask zones that cannot be viewed by the operator The privacy mask can prevent certain surveillance areas to be viewed or recorded Steps 1 Enter the Privacy Mask Settings interface Menu gt Camera gt Privacy Mask 2 Select the camera to set privacy mask 3 Click the checkbox of Enable Privacy Mask to enable this feature IP Camera 1 01 01 2010 Fri 11
29. button to get the latest status of the port mapping 133 User Manual of DS 7600NI Series NVR Manual Port Type External Port Mapping IP Address Status HTTP Port 80 172 6 21 31 Active RTSP Port 172 6 21 31 Active HTTPS Port 172 6 21 31 Active Refresh Figure 9 25 UPnP Settings Finished Manual 9 2 12 Configuring High speed Download Purpose You can enable the High speed Download function to widen the outgoing bandwidth of the device In this way you can speed up the download of record files through IE browser or CMS software Note If you enable the high speed download function the local menu operation will be affected It is recommended to disable this function after finishing the remote downloading of record files Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the More Settings tab to enter the More Settings interface as shown in Figure 9 14 3 Check the checkbox of Enable High speed Download And click the OK button in the pop up message box to confirm the settings Figure 9 26 High speed Download Settings Menu Attention Enabling high speed download may cause the local GUI operation stucked Figure 9 27 Message Box of High speed Download 4 Click Apply button to save and exit the interface 134 User Manual of DS 7600NI Series NVR 9 3 Checking Network Traffic Purpose You can check the network traffic to obtain real time information of NVR such as
30. deleted The actual keeping time for the file should be determined by the capacity of the HDD Redundant Record Enabling redundant record means you save the record in the redundant HDD See Chapter Configuring Redundant Recording Record Audio Check the checkbox to enable or disable audio recording 2 Click Apply to save the settings Note The redundant record is to decide whether you want the camera to save the record files in the redundant HDD You must configure the redundant HDD in HDD settings For detailed information see Chapter 10 3 2 Setting HDD Property Note The parameters of Main Stream Event are read only 3 Parameters Settings for Sub stream 1 Enter the Sub stream tab page Camera IP Camera 3 Stream Type Video amp Audio Resolution 352 288 ClIF Bitrate Type Variable Video Quality Medium Frame Rate 25fps Max Bitrate Mode General Max Bitrate Kbps 512 Max Bitrate Range Reco 384 640 Kbps Figure 5 4 Sub stream Parameters 2 Configure the parameters of the camera 3 Click Apply to save the settings 58 User Manual of DS 7600NI Series NVR 5 2 Configuring Record Schedule Purpose Set the record schedule and then the camera automatically starts stops recording according to the configured schedule Steps 1 Enter the Record Schedule interface Menu gt Record gt Schedule 2 Configure Record Schedule 1 Select Record Schedule IP Camera 1 i 8 10 Edit Co
31. engineer from Hikvision to do the further process When using the NVR to get the live view audio there is no sound or there is too much noise or the volume is too low Possible Reasons a Cable between the pickup and IPC is not connected well impedance mismatches or incompatible b The stream type is not set as Video amp Audio c The encoding standard is not supported with NVR Steps 1 Verify the cable between the pickup and IPC is connected well impedance matches and compatible 183 User Manual of DS 7600NI Series NVR Log in the IPC directly and turn the audio on check if the sound is normal If not please contact the manufacturer of the IPC 2 Verify the setting parameters are correct Select Menu gt Record gt Parameters gt Record and set the Stream Type as Audio amp Video 3 Verify the audio encoding standard of the IPC is supported by the NVR NVR supports G722 1 and G711 standards and if the encoding parameter of the input audio is not one of the previous two standards you can log in the IPC to configure it to the supported standard 4 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from Hikvision to do the further process The image gets stuck when NVR is playing back by single or multi channel Possible Reasons a Poor network between NVR and IPC and there exists packet loss during the transmission
32. environment Unit is designed for indoor use only Keep all liquids away from the device Ensure environmental conditions meet factory specifications Ensure unit is properly secured to a rack or shelf Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit Use the device in conjunction with an UPS if possible Power down the unit before connecting and disconnecting accessories and peripherals A factory recommended HDD should be used for this device Improper use or replacement of the battery may result in hazard of explosion Replace with the same or equivalent type only Dispose of used batteries according to the instructions provided by the battery manufacturer User Manual of DS 7600NI Series NVR Thank you for purchasing our product If there is any question or request please do not hesitate to contact dealer This manual is applicable to the models listed in the following table DS 7604NI SE Network Video Recorder DS 7608NI SE DS 7616NI SE DS 7604NI SE N Network Video Recorder DS 7608NI SE N DS 7616NI SE N 7600NI SE P DS 7604NI SE P Network Video Recorder DS 7608NI SE P DS 7616NI SE P 7600NI V DS 7604NI V Network Video Recorder DS 7608NI V DS 7616NI V T600NI VP DS 7604NI VP Network Video Recorder DS 7608NI VP DS 7616NI VP User Manual of DS 7600NI Series NVR Product Key Features General Connectable to network cameras network dome
33. firmware on your NVR can be upgraded by local backup device or remote FTP server 12 4 1 Upgrading by Local Backup Device Steps 1 Connect your NVR with a local backup device where the update firmware file is located 2 Enter the Upgrade interface Menu gt Maintenance gt Upgrade 3 Click the Local Upgrade tab to enter the local upgrade menu as shown in Figure 12 12 2011062710363 1log Ecok xis Compare Excel exe B Recycled B bond0_2011062417 B USB1 1 Folder Folder Folder Folder Folder 15KB File 23KB File 129KE File AKB File 1 0274KB File 09 17 2010 11 19 04 04 02 2011 17 45 24 08 04 2010 17 35 20 06 21 2011 17 55 42 06 27 2011 14 56 12 06 27 2011 10 36 30 05 26 2011 18 32 14 04 20 2011 08 51 42 02 22 2011 14 16 18 06 24 2011 17 20 48 Figure 12 12 Local Upgrade Interface 4 Select the update file from the backup device 5 Click the Upgrade button to start upgrading Refresh 6 After the upgrading is complete reboot the NVR to activate the new firmware 12 4 2 Upgrading by FTP Before you start Configure PC running FTP server and NVR to the same Local Area Network Run the 3 party TFTP software on the PC and copy the firmware into the root directory of TFTP Steps 1 Enter the Upgrade interface Menu gt Maintenance gt Upgrade 2 Click the FTP tab to enter the local upgrade interface as shown in Figure 12 13 166 User Manual of DS 7600NI Series NVR
34. for time synchronization 127 User Manual of DS 7600NI Series NVR 9 2 4 Configuring SNMP Purpose You can use SNMP protocol to get device status and parameters related information Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the SNMP tab to enter the SNMP Settings interface as shown in Figure 9 13 public private 162 Figure 9 13 SNMP Settings Interface 3 Check the SNMP checkbox to enable this feature 4 Configure the following SNMP settings Trap Address IP Address of SNMP host e Trap Port Port of SNMP host 5 Click Apply button to save and exit the interface Note Before setting the SNMP please download the SNMP software and manage to receive the device information via SNMP port By setting the Trap Address the NVR is allowed to send the alarm event and exception message to the surveillance center 9 2 5 Configuring Remote Alarm Host Purpose With a remote alarm host configured the NVR will send the alarm event or exception message to the host when an alarm is triggered The remote alarm host must have the Network Video Surveillance software installed Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the More Settings tab to enter the More Settings interface as shown in Figure 9 14 Figure 9 14 More Settings Interface 128 User Manual of DS 7600NI Series NVR 3 Enter Alarm Host IP and Alarm
35. refers to the function can only be supported when it uses the AXIS protocol ARECONT IPC Manufacturer or Max Version Sub stream Protocol Resolution A1D 310 V4 12 09 AC A1D 310 V4 12 09 AC A1D 220 V3 13 16 AC 65172 65175 65143 65220 65175 65175 5 09 1 AXIS M3011 ONVIF compatibility M3014 ONVIF compatibility P3301 ONVIF compatibility P3304 ONVIF compatibility P3343 ONVIF compatibility P3344 ONVIF compatibility 5 21 1 5 11 2 5 20 1 5 20 1 Jv Only AXIS is supported J Only AXIS is supported Jv Only AXIS is supported Jv Only AXIS is supported Jv Only AXIS is supported 1440x900 720x576 720x576 P5532 Q7404 AutoDome Jr 800HD 39500450 1920x1080 Bosch NBC 265 P 07500453 1280x720 ONVIF compatibility Dinion NBN 921 P 10500453 1280x720 FB 130Np ONVIF V3 1 0 8 1280x1024 compatibility Brickcom CB S00Ap ONVIF V3 2 1 3 1280x1024 compatibility WFB 100Ap V3 1 0 9 1280x800 VB M400 Ver 1 0 0 1280x960 Canon Ver 1 0 0 U U N N O VB M6000D 1280x960 191 User Manual of DS 7600NI Series NVR IPC Manufacturer or Model Version Max Sub stream Audio Protocol Resolution WV SW152 ONVIF Application 1 66 800x600 compatibility Image data 1 05 WV SC386 ONVIF Application 1 66 1280x960 compatibility Image data 1 05 WV SW155 ONVIF Application 1 66 x 1280x960 Panasonic compat
36. t want to install a HDD select Menu gt Configuration gt Exceptions and uncheck the Audible Warning checkbox of HDD Error 2 Verify the HDD 1s initialized 1 Select Menu gt HDD gt General 2 Ifthe status of the HDD is Uninitialized please check the checkbox of corresponding HDD and click the Init button 3 Verify the HDD is detected or is in good condition 1 Select Menu gt HDD gt General 2 Ifthe HDD is not detected or the status is Abnormal please replace the dedicated HDD according to the requirement 4 Check if the fault is solved by the step 1 to step 3 1 Ifitis solved finish the process 2 Ifnot please contact the engineer from Hikvision to do the further process e The status of the added IPC displays as Disconnected when it is connected through Hikvision Protocol Select Menu gt Camera gt Camera gt IP Camera to get the camera status 180 User Manual of DS 7600NI Series NVR Possible Reasons a Network failure and the NVR and IPC lost connections b The configured parameters are incorrect when adding the IPC c Insufficient bandwidth Steps 1 Verify the network is connected 1 Connect the NVR and PC with the RS 232 cable 2 Open the Super Terminal software and execute the ping command Input ping IP e g ping 172 6 22 131 Note Simultaneously press Ctrl and C to exit the ping command If there exists return information and
37. tag management Pause reverse Pause play play Scaling Play Reverse play up down the CS Speed up Single frame Single frame time line play reverse play wero PT Cd Note Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames 76 User Manual of DS 7600NI Series NVR 6 1 2 Playing Back by Time Purpose Play back video files recorded in specified time duration Multi channel simultaneous playback and channel switch are supported Steps 1 Enter playback interface Menu gt Playback 2 Check the checkbox of channel s in the channel list and then double click to select a date on the calendar Figure 6 5 Playback Calendar Note If there are record files for that camera in that day in the calendar the icon for that day is displayed as 9 Otherwise it is displayed as In the Playback interface The toolbar in the bottom part of Playback interface can be used to control playing process as shown in Figure 6 6 Camera iPCamera 01 iPCamera 02 iPCamera 03 iCamera01 iPCamera 05 iPCamera 06 iY iPCamera 08 iPCamera 09 iPCamera 10 iPCamera 11 iPCamera 12 iPCamera 13 04 25 2013 10 00 12 04 25 2013 16 02 59 Figure 6 7 Toolbar of Playback by Time 77 User Manual of DS 7600NI Series NVR Note The imma Zi ee rd er a indicates the start end time of the record Table 6 2
38. the time value is little the network is normal 2 Verify the configuration parameters are correct 1 Select Menu gt Camera gt Camera gt IP Camera 2 Verify the following parameters are the same with those of the connected IP devices including IP address protocol management port user name and password 3 Verify the whether the bandwidth is enough 1 Select Menu gt Maintenance gt Net Detect gt Network Stat 2 Check the usage of the access bandwidth and see if the total bandwidth has reached its limit 4 Check if the fault is solved by the step 1 to step 3 If it is solved finish the process If not please contact the engineer from Hikvision to do the further process The IPC frequently goes online and offline and the status of it displays as Disconnected Possible Reasons a The IPC and the NVR versions are not compatible b Unstable power supply of IPC c Unstable network between IPC and NVR d Limited flow by the switch connected with IPC and NVR Steps 1 Verify the IPC and the NVR versions are compatible 1 Enter the IPC Management interface Menu gt Camera gt Camera gt IP Camera and view the firmware version of connected IPC 2 Enter the System Info interface Menu gt Maintenance gt System Info gt Device Info and view the firmware version of NVR 2 Verify power supply of IPC is stable 1 Verify the power indicator is normal 2 When the IPC is offline p
39. 1 0 build 130111 Sub stream Audio 1280x720 DS 2CD764FWD E 1 V4 1 0 build 130111 1280x720 DS 2CD8264FWD E 1 V4 1 0 build 130111 1280x720 DS 2CD2012 I V4 0 9 build 130106 1280x960 DS 2CD2112 I V4 0 9 build 130106 1280x960 DS 2CD2212 I V4 0 9 build 130106 1280x960 DS 2CD2312 I V4 0 9 build 130106 1280x960 DS 2CD2032 I V4 0 9 build 130106 1280x960 DS 2CD2132 I V4 0 9 build 130106 1280x960 DS 2CD2232 I V4 0 9 build 130106 1280x960 DS 2CD2332 I V4 0 9 build 130106 DS 2CD7133FE aoas DS ICDF EO aoas DS ICDF E aoas DS 2CD8133F E 640x480 DS 2CD8233F E 1 640x480 1280x960 SD Network Camera DS 2CD802NF V2 0 build 090522 DS 2CD812PF V2 0 build 090715 704x576 DS 2CD832F DS 2CD893PF WD E V4 1 0 build 130111 704x576 DS 2CD793PF WD E I V4 1 0 build 130111 704x576 DS 2CD793NFE WD E D V4 1 0 build 130111 704x576 Thermal Camera DS 2CD8313PF E40 V3 2 build 120528 352x288 Ls 1 Ds2cp912 Van mats 130129 100x1200 ps2cpe1m V3 0 piel 30129 19201060 DS20D915 Van0 ia 10129 2048x1336 ps2cpsisia vss0nuia non 2182008 Intelligent Traffic DS 2CD9152 V3 3 1 build 130301 2560x1920 Camera DS 2CD9152 H V3 3 0 build 130120 2592x2048 DS 2CD966 B V3 1 0 build120423 1360x1024 x x DS 2CD966 V B DS 2CD976 B V3 1 0 build120423 1600x1200 188 a User Manual of DS 7600NI Series NVR Max Type Model Version Resolution on DS 2CD977 B V3 1 build 120423 1920x1080 Sub stream Audio DS 2CD97
40. 132 User Manual of DS 7600NI Series NVR If you select Auto the Port Mapping items are read only and the external ports are set by the router automatically Steps 1 Click Apply button to save the settings 2 You can click Refresh button to get the latest status of the port mapping ping Typ Auto Port Type Edit External Port Mapping IP Address Status 172 6 21 31 er Refresh Figure 9 23 UPnP Settings Finished Auto Task2 Manual If you select Manual as the mapping type you can edit the external port on your demand by clicking LA to activate the External Port Settings dialog box Steps 1 Click LA to activate the External Port Settings dialog box Configure the external port No for server port http port RTSP port and https port respectively Notes 1 You can use the default port No or change it according to actual requirements 2 External Port indicates the port No for port mapping in the router 3 The value of the RTSP port No should be 554 or between 1024 and 65535 while the value of the other ports should be between 1 and 65535 and the value must be different from each other If multiple devices are configured for the UPnP settings under the same router the value of the port No for each device should be unique External Port Settings Server Port 8001 Cancel Figure 9 24 External Port Settings Dialog Box 2 Click Apply button to save the settings 3 You can click Refresh
41. 25 1 038 801KB gt 10 20 2011 15 21 25 16 11 23 722 552KB 10 20 2011 10 33 51 11 18 56 668 672KB E pLELEpDpEE BEESSEEaEES 5 B Dane Start time 10 20 2011 09 08 52 End time 10 20 2011 11 50 24 Total size 6 482MB Cancel Figure 7 11 Result of Normal Video Search for Backup 4 Export Click Export button and start backup Note If the inserted USB writer or SATA writer is not recognized e Click the Refresh button e Reconnect device e Check for compatibility from vendor 97 User Manual of DS 7600NI Series NVR Export USB CD DVD RW Refresh Figure 7 12 Export by Normal Video Search using USB Writer Stay in the Exporting interface until all record files are exported with pop up message box Export finished Export finished Figure 7 13 Export Finished 5 Check backup result Choose the record file in Export interface and click button oR check it The Player player exe will be exported automatically during record file export Export USB CD DYD RW E Folder 06 23 2011 20 07 22 s Backup Folder 06 23 2011 20 07 28 E Export record files to me OKB File 06 23 2011 20 07 58 Vvelcome to use backup OKB File 06 23 2011 70 07 36 chO3_ 201 10623000000 267MB File 06 23 2011 20 15 02 E ch03_201 10623042932 280MB File 06 23 2011 20 11 14 E ch03_201 10623091403 4 423KB File 06 23 2011 20 11 20 _ ch03_201 10623092323 127MB File 06 23 2011 20 12 12 chO3_ 2011062311332
42. 3 2701106730973 723 2 TME le JE 3 2U fal So A chO3_201106231133275 BH chO3_ 20110623132800 E chO3_20110623134743 B player exe m PR mes dees A n hi ewe tine lt 110MB File 18 36 KB File 37 305KB File 608KB File visor ota New Folder 96 06 23 2011 20 12 54 06 23 2011 20 13 02 06 23 2011 20 13 12 06 23 2011 20 09 40 OL NA NINA A 44 73 ALD Format Export Cancel Figure 7 9 Checkup of Export Result using USB Flash Drive d O 9 9 v lt User Manual of DS 7600NI Series NVR Backup using USB writer and SATA writer Steps 1 Enter Export interface Menu gt Export gt Normal 2 Set search condition and click Search button to enter the search result interface MIP Camera Dy eee DA 1D ee D 07 05 2013 16 48 08 08 05 2013 00 48 18 All All 0 7 05 2013 00 00 00 0 7 05 2013 23 59 59 Figure 7 10 Normal Video Search for Backup 3 Select record files you want to back up Click button to play the record file if you want to check it Check the checkbox before the record files you want to back up Note The size of the currently selected files is displayed in the lower left corner of the window Search result 10 20 2011 11 50 24 15 23 54 1 038 237KB 10 20 2011 15 23 54 16 11 53 399 657KB 10 20 2011 10 33 53 11 17 18 692 336KB 10 20 2011 11 1 18 11 18 52 25 163KB 10 20 2011 13 13 10 14 16 30 1 013 691KB 10 20 2011 14 16 30 15 21
43. 5 110MB File 06 23 2011 20 12 54 E ch03_201 10623132800 18 367KB File 06 23 2011 20 13 02 E ch03_201 10623134743 37 305KB File 06 23 2011 20 13 12 player exe 608KB File 06 23 2011 20 09 40 ee ee oe vo MO rot Nf NA NINA A AANA AO ro u o i a i lt IIADPII PAQAQIOAO Figure 7 14 Checkup of Export Result using USB Writer 98 User Manual of DS 7600NI Series NVR 7 1 33 Backing up by Event Search Purpose Back up event related record files using USB devices USB flash drives USB HDDs USB writer or SATA writer Quick Backup and Normal Backup are supported Steps 1 Enter Export interface Menu gt Export gt Event 1 Select Alarm Input from the dropdown list of Event Type Note Event types contain Alarm Input and Motion here we take the backing up by alarm input as an example 2 Select the alarm input No and time Alarm Input 07 05 2013 00 00 00 07 05 2013 mi 23 59 59 1 2 6 23 105 Figure 7 15 Event Search for Backup 2 Click Search button to enter the Search Result interface Alarm Input E D2 lt 1 07 05 2013 16 50 24 07 05 2013 16 53 56 Total 1 P 1 1 Quick Export Details Cancel Figure 7 16 Result of Event Search 3 Select record files to export 1 Clicking Quick Export button will export record files of all channels triggered by the selected alarm input 2 Clicking Details button will take you to the interface with detailed informat
44. 6 04 2012 00 00 00 06 04 2012 23 59 59 All All Figure 12 6 Log Search Interface 2 Set the log search conditions to refine your search including the Start Time End Time Major Type and Minor Type 3 Click the Search button to start search log files 4 The matched log files will be displayed on the list shown below 161 User Manual of DS 7600NI Series NVR Log Export Start Time 06 04 2012 00 00 00 End Time 06 04 2012 23 59 59 Major Type All Minor Type All 99 06 04 2012 06 12 21 Start Motion Det 98 06 04 2012 06 10 30 Stop Motion Det 97 06 04 2012 06 10 16 Start Motion Det 96 06 04 2012 06 07 49 Stop Motion Det 95 06 04 2012 06 07 36 Start Motion Det 94 06 04 2012 06 02 39 Stop Motion Det 93 06 04 2012 06 02 26 Start Motion Det 92 06 04 2012 05 59 26 Stop Motion Det 91 06 04 2012 05 59 13 Start Motion Det 90 06 04 2012 05 45 13 Stop Motion Det 89 06 04 2012 05 44 59 Start Motion Det 88 06 04 2012 05 43 15 Stop Motion Det Total 1052 S99 SSS VSIVSISIVIYI9 VIS IDIDIDIDIPIIIIYDS v Figure 12 7 Log Search Results Note Up to 2000 log files can be displayed each time 5 You can click the button of each log or double click it to view its detailed information as shown in Figure 12 8 And you can also click the button to view the related video files if available Log Information lime 06 04 2012 05 06 42 Type Alarm Start Motion Detection Local User N
45. 6 18 2012 09 44 05 06 18 2012 09 44 11 06 18 2012 10 08 48 06 18 2012 10 08 48 06 18 2012 10 10 10 06 18 2012 10 15 41 00 00 00 23 59 59 Local Operation Login N A Local Operation Login N A IP Camera Disconnec IP Camera Disconnec IP Camera Disconnec IP Camera Disconnec IP Camera Disconnec IP Camera Disconnec Local Operation Add Local Operation Con IP Camera Disconnec Local Operation Con Playback 6 1 6 Playing Back External File Purpose N A N A N A N A N A N A N A Preview N A Preview 191 999999 Perform the following steps to look up and play back files in the external devices Steps 1 Enter Tag Search interface Menu gt Playback 2 Select the External File in the drop down list on the top left side The files are listed in the right side list You can click the button to refresh the file list 3 Select and click the Q button to play back it 85 SS SSF ssssgss8gsg 8 FIs User Manual of DS 7600NI Series NVR External File USB1 4 Play E FileZilla 3 4 E digicap mav eer E player exe Baseline Quic ESELTA TC meliite E ch03_ 201211 E cho3_ 201211 E ch03_ 201211 a E ch01_ 201212 hy E cho2_201212 ee i E STE Presenta 9DDDIDIDDIDIDDD 5 1 f 1 j m CA h AiD bopt Cuns fem bem we 4 I gt z G 4 Refresh Figure 6 21 Interface of External File Playback 86 User Manual of DS 7600NI Series NVR
46. 7 C DS 2DF1 772 DS 2DM 1 772 V4 1 4 build 130110 1280x720 DS 2DF1 774D DS 2DF7284 A DS 2DF7274 A V4 2 4 build 130126 1280x960 DS 2DF5284 A DS 2DF5274 A V2 0 1 build 110520 DS 2DM1 718 Network Speed Dome V3 1 2 build 121124 V2 0 1 build 110520 DS 2DM1 518 V3 1 2 build 121124 DS 2DF 1 402 V3 1 4 build 130204 704x576 DS 2DF1 402N V3 1 4 build 130204 704x576 V2 0 1 build 110520 DS 2DF1 618H V3 1 0 build110811 V2 0 1 build 110520 DS 2DF1 718 V3 1 2 build 121124 V2 0 1 build 110520 DS 2DF1 518 V3 1 2 build 121124 DS 6601HFHI V1 0 4 build 130115 1920x1080 HD Decoder DS 6601HFHI L V 1 0 4 build 130115 1920x1080 DS 6501HCI SATA DS 6502HCI SATA V1 0 1 build 110104 DS 6504HCI SATA DS 6516HCI SATA DS 6501HFI SATA SD Decoder DS 6502HFI SATA V1 0 1 build110104 DS 6504HFI SATA DS 6508HFI SATA DS 6601HCI V1 2 0 build 120215 DS 6602HCI 189 704x576 704x576 704x576 704x576 704x576 704x576 704x576 704x576 User Manual of DS 7600NI Series NVR Max Model Version Sub stream Resolution DS 6601HFI DS 6602HFI V1 2 0 build 120215 704x576 DS 6604HFI 190 User Manual of DS 7600NI Series NVR List of Third party IP Cameras Note ONVIF compatibility refers to the camera can be supported both when it uses the ONVIF protocol and its private protocols Only ONVIF is supported refers to the camera can only be supported when it uses the ONVIF protocol Only AXIS is supported
47. A Host IP Address N A Parameter Type N A Camera No D3 Description N A Previous Figure 12 8 Log Details 6 If you want to export the log files click the Export button to enter the Export menu as shown in Figure 12 g 162 User Manual of DS 7600NI Series NVR Refresh Folder 2010 09 17 11 19 04 Folder 2011 04 02 17 45 24 Folder 2010 08 04 17 35 20 s Folder 2011 06 21 17 55 42 E Book1 xls 23KB File 2011 05 26 18 32 14 B Compare Excel exe 129KB File 2011 04 20 09 51 42 B Recycled 4KB File 2011 02 22 14 16 18 E bond0_ 201106241 72C 1 024KB File 2011 06 24 17 20 48 E digicap mav 19 790KB File 2011 06 23 09 05 20 9O9OODOBO New Folder Format Cancel Figure 12 9 Export Log Files 7 Select the backup device from the dropdown list of Device Name 8 Click the Export to export the log files to the selected backup device You can click the New Folder button to create new folder in the backup device or click the Format button to format the backup device before log export Notes 1 Please connect the backup device to NVR before operating log export 2 The log files exported to the backup device are named by exporting time e g 2011051412484 1logBack txt To export all the log files You can enter the Log Export interface Menu gt Maintenance gt Log Information gt Log Export 163 User Manual of DS 7600NI Series NVR Log Search Figure 12 10 Log Export Interface You can check the checkbox of the
48. ATES THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IN NO EVENT WILL HIKVISION ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL INCIDENTAL OR INDIRECT DAMAGES INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION AND THE LIKE ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU User Manual of DS 7600NI Series NVR Regulatory information FCC information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions
49. Add the allocated NetHDD 4 Select the type to NAS or IP SAN 5 Configure the NAS or IP SAN settings e Add NAS disk 1 Enter the NetHDD IP address in the text field 2 Click the Search button to search the available NAS disks 3 Select the NAS disk from the list shown below Or you can just manually enter the directory in the text field of NetHDD Directory 4 Click the OK button to add the configured NAS disk Note Up to 8 NAS disks can be added 142 User Manual of DS 7600NI Series NVR Add NetHDD NetHDD 1 NAS i an 24 201 idvridvr_3 Directory fdvridvr_1 mnt backup indexbackup fdvridvr_8 fdvrfliu_O fdvridvr_2 Cancel Figure 10 7 Add NAS Disk Add IP SAN 1 Enter the NetHDD IP address in the text field 2 Click the Search button to search the available IP SAN disks 3 Select the IP SAN disk from the list shown below 4 Click the OK button to add the selected IP SAN disk Note Up to 1 IP SAN disk can be added Add NetHDD NetHDD 1 IP SAN Le Ge a 210 iqn 2004 05 storos t 8 iqn 2004 05 storos t 41 iqn 2004 05 storos t 1000 Cancel Figure 10 8 Add IP SAN Disk 6 After having successfully added the NAS or IP SAN disk return to the HDD Information menu The added NetHDD will be displayed in the list Note If the added NetHDD is uninitialized please select it and click the Init button for initialization Mabel Capacity Status Property Type Free Space Gro Edit Del 3
50. DMI Interface HDMI video output connector VGA Output DB9 connector for VGA output Display local video output and menu Power Supply 100 240VAC power supply Universal Serial Bus USB ports for additional devices such as USB USB Interface i mouse and USB Hard Disk Drive HDD Network Interfaces with PoE function Network interface for the cameras and to provide power over Ethernet for DS 7600NI VP 22 User Manual of DS 7600NI Series NVR Chapter 2 Getting Started 23 User Manual of DS 7600NI Series NVR 2 1 Starting Up and Shutting Down the NVR Purpose Proper startup and shutdown procedures are crucial to expanding the life of the NVR Before you start Check that the voltage of the extra power supply is the same with the NVR s requirement and the ground connection is working properly Starting up the NVR Steps 1 Check the power supply is plugged into an electrical outlet It is HIGHLY recommended that an Uninterruptible Power Supply UPS be used in conjunction with the device 2 Turn on the power switch on the rear panel 3 After startup the Power LED indicator turns on supported by DS 7600NI SE series NVR only A splash screen with the status of the HDD appears on the monitor The row of icons at the bottom of the screen shows the HDD status X means that the HDD is not installed or cannot be detected Shutting down the NVR Steps 1 Enter the Shutdown menu Menu gt Shutdown Shutd
51. EA E N E 50 4 2 3 A TAE T T ENEE EN EEEE E E E E EE E EA 51 4 2 4 Calme Paroi T TT T TRIR 3 4 2 5 Custom IOP Ath a E E Senantac 53 4 2 6 Callina Pattes ni E A S TTE 54 Aa PITA Cono ToolBar E 55 Chapter SRecord Sec GS eiccscseccccs scssvcesucieecssesdsseuscedescusucvevascusdccevenevesenssevescscuevesancescesssesevesessoedscasovevevasseeveess 56 31 AConounis Recordine Parametleri Soiden a ai a 57 D2 Conhenurine Record schodili senri io cassat s dasann ea EEE REEE 59 53 Conteutine Monon Deteccion Recordsissa a a a a a 62 5 4 Configuring Alarm Triggered Record cccsssssssssseeecceccceeccceasesssseeeecceceeeeeseaausaesseseeeeeeeeeeess 64 User Manual of DS 7600NI Series NVR 329 Mammal RECO scct soos titers acts Sea a a Aeobeeaeach gases Gabbe eGare a a 66 36 Contouring Holiday Record nesas ned iwewas incline Venous stioeicndslisdewsstechent E sintdadslivcans 67 Z Conneunne Redundant Recordi schism ccatids cicsarssscerlecteveus contort ecstasaranacuneneunngien beaten 69 58 Conheurines HDD Group for Recording rne ces acsncve sch E e a ees suaamepenchaverestea 71 39 Files Protec On s t ase a cagevsacees cxsacpes a sannreis dao eas ansanass S 72 Chapter GP lay Dack arasonar ETEN 74 61 Playine Back Recon Plesa E S 73 6 1 1 Playing Back Dy Canine iis cycesixcernonteien teludeseesivtalnues itd obicsiweaeseMudusecs iia cate sed dvecniuedverebite 75 6 1 2 Pane Back ny Tiiiie sss ts tuiainitusnaiees N 77 6 1 3 Playing Back by Event Sea
52. ES lt 4 W Figure 7 21 Interface of Playback by Time 4 Click Yes to save video clips and enter Export interface or click No to quit and do not save video clips Attention There are some video clips to be saved Do you want to save them now Yes No Figure 7 22 Attention to Video Clip Saving 5 Export Click Export button and start backup Note If the inserted USB device is not recognized e Click the Refresh button e Reconnect device e Check for compatibility from vendor You can also format USB flash drive or USB HDDs via the device Export USB1 1 Refresh 06 23 2011 06 23 2011 06 23 2011 06 23 2011 06 23 2011 20 07 22 20 07 28 20 07 58 20 07 36 20 15 02 20 11 14 20 11 20 Folder Folder OKB File OKB File 26 MB File E Export record files to me B Welcome to use backup ch03_ 20110623000000 E ch03_20110623042932 280MB File 06 23 2011 E ch03_20110623091403 4 423KB File 06 23 2011 ch0 16230923722 2 TMB File 06 23 20 B ch03_20110623113325 110MB File 06 23 2011 20 12 54 BH chO3_ 20110623132800 B chO03_ 20110623134 743 B player exe PR eee dees HE a hi ewe tie lt 18 36 KB File 37 305KB File 608KB File ALPA ES etn New Folder 06 23 2011 06 23 2011 06 23 2011 NAE a4 VA A Format 20 13 02 20 13 12 20 09 40 44 1 Af Cancel Figure 7 23 Export Video Clips Using USB Flash Drive 102 C C C E g gt E C fm gt
53. HDD Click the Export button to export all the log files stored in the HDD 164 User Manual of DS 7600NI Series NVR 12 3 Importing Exporting Configuration Files Purpose The configuration files of the NVR can be exported to local device for backup and the configuration files of one NVR can be imported to multiple NVR devices if they are to be configured with the same parameters Steps 1 Enter the Import Export Configuration File interface Menu gt Maintenance gt Import Export Folder 09 17 2010 11 19 04 Folder 04 02 2011 17 45 24 Folder 08 04 2010 17 35 20 Folder 06 21 2011 17 5542 Folder 06 27 2011 14 56 13 B 2011067110363 log 15KB File 06 27 2011 10 36 30 B Book xls 23KB File 05 26 2011 18 32 14 B Compare Excel exe 129KB File 04 20 2011 09 51 42 B Recycled AKB File 02 22 2011 14 16 18 Bbondd 2011062417 1 024KB File 6 24 2011 1 eso ale B digicap may 19 T90KEB File O6 23 2710117 09 05 20 180MB New Folder Import Export Back Figure 12 11 Import Export Config File 2 Click the Export button to export configuration files to the selected local backup device 3 To import a configuration file select the file from the selected backup device and click the Import button After the import process is completed you must reboot the NVR Note After having finished the import of configuration files the device will reboot automatically 165 User Manual of DS 7600NI Series NVR 12 4 Upgrading System Purpose The
54. Host Port in the text fields The Alarm Host IP refers to the IP address of the remote PC on which the Network Video Surveillance Software e g 1VMS 4200 is installed and the Alarm Host Port must be the same as the alarm monitoring port configured in the software Figure 9 15 Configure Alarm Host 4 Click Apply button to save and exit the interface 9 2 6 Configuring Multicast Purpose The multicast can be configured to realize live view for more than 64 cameras through network for DS 7600NI SE series NVR A multicast address spans the Class D IP range of 224 0 0 0 to239 255 255 255 It is recommended to use the IP address ranging from 239 252 0 0 to 239 255 255 255 Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the More Settings tab to enter the More Settings interface as shown in Figure 9 14 3 Set Multicast IP as shown in Figure 9 16 When adding a device to the Network Video Surveillance Software the multicast address must be the same as the NVR s multicast IP Server Port 8000 HTTP Pori 80 Multicast IP 239 221 2 78 Figure 9 16 Configure Multicast 4 Click Apply button to save and exit the interface Note The multicast function should be supported by the network switch to which the NVR is connected 9 2 7 Configuring RTSP Purpose The RTSP Real Time Streaming Protocol is a network control protocol designed for use in entertainment and communications s
55. I Series NVR 2 Inthe NVR Domain Name text field enter the domain obtained from the NO IP website WWw no ip com 3 Enter the User Name and Password registered in the NO IP website NO IP Figure 9 7 NO IP Settings Interface HiDDNS Enter the Server Address and Device Domain Name for HiDDNS 1 Enter the Server Address of the HiDDNS server which is www hik online com by default 2 Enter the Device Domain Name You can use the alias you registered in the HiDDNS server or define a new device domain name If a new alias of the device domain name is defined in the NVR it will replace the old one registered on the server You can register the alias of the device domain name in the HiDDNS server first and then enter the alias to the Device Domain Name in the NVR you can also enter the domain name directly on the NVR to create a new one HiDDNS www hik online com Figure 9 8 HiDDNS Settings Interface Register the device on the HiDDNS server 1 Goto the HiDDNS website www hik online com 2 Click Besistetmewuset to register an account if you do not have one and use the account to log in 125 User Manual of DS 7600NI Series NVR Register new user User Name Password Confirm Password Real Name Email Remark Figure 9 9 Register an Account 3 Inthe Device Management interface click Lada to register the device Add Device DS DVR V2000678677 8a6tt80 Figure 9 10 Register the Devi
56. KB 10 20 2011 11 1 7 18 11 18 52 25 163KB 10 20 2011 13 13 10 14 16 30 1 013 691KB 10 20 2011 14 16 30 15 21 25 1 038 801KB 10 20 2011 15 21 25 16 11 23 722 552KB 10 20 2011 10 33 51 11 18 56 668 672KB gt i DPLE 5 B Dae Start time 10 20 2011 09 08 52 End time 10 20 2011 11 50 24 Total size 6 482MB Cancel Figure 7 27 Result of Normal Video Search for Backup 3 Backup device management Click New Folder button if you want to create a new folder in the backup device Select a record file or folder in the backup device and click i button if you want to delete it Select a record file in the backup device and click button to play it Click Format button to format the backup device Note If the inserted USB device is not recognized e Click the Refresh button e Reconnect device e Check for compatibility from vendor E chO3_201106230000C 267MB File 06 23 2011 20 15 02 ch03_20110623042932 280MB File 06 23 2011 20 11 14 ch03_201106230914 C 4 423KB File 06 23 2011 20 11 20 chO3_ 2011062309237 127MB File 06 23 2011 20 12 12 E chO3_ 2011062311332 110MB File 06 23 2011 20 12 54 E chO3 2701106231328C 18 36 7KB File 06 23 2011 20 13 02 E ch03_ 20110623134 74 37 305KB File 06 23 2011 20 13 12 D O O 9 99I B player exe 608KB File 06 23 2011 20 09 40 New Folder Format Cancel Figure 7 28 USB Flash Drive Management Management of USB writers or DVD R W 1 Enter Sear
57. NVR 3 3 Adjusting Live View Settings Purpose Live View settings can be customized according to different needs You can configure the output interface dwell time for screen to be shown mute or turning on the audio the screen number for each channel etc Steps 1 Enter the Live View Settings interface Menu gt Configuration gt Live View VGA HDMI n Rate No Switch a VGA HDMI 10s Figure 3 6 Live View General The settings available in this menu include Video Output Interface Designates the output to configure the settings for Only VGA HDMI is selectable by default Live View Mode Designates the display mode to be used for Live View Dwell Time The time in seconds to dwell between switching of channels when enabling auto switch in Live View Enable Audio Output Enables disables audio output for the selected video output Event Output Designates the output to show event video Full Screen Monitoring Dwell Time The time in seconds to show alarm event screen 2 Setting Cameras Order General VGA HDMI Camera Camera Name 1 D2 Camera 02 D3 IPCamera 03 Figure 3 7 Live View Camera Order To set the camera order 1 Select a View mode in GEEL 44 User Manual of DS 7600NI Series NVR 2 Select the small window and double click on the channel number to display the channel on the window You can click ice button to start live view for all the channels and click ey t
58. Operator or Guest Different user levels have different operating permission Operator The Operator user level has permission of Two way Audio in Remote Configuration and all operating permission in Camera Configuration Guest The Guest user has no permission of Two way Audio in Remote Configuration and only has the local remote playback in the Camera Configuration User s MAC Address The MAC address of the remote PC which logs onto the NVR If it is configured and enabled it only allows the remote user with this MAC address to access the NVR 4 Click the OK button to save the settings and go back to the User Management interface The added new user will be displayed on the list as shown in Figure 13 6 Admin 00 00 00 00 00 00 Figure 13 6 Added User Listed in User Management Interface 5 Select the user from the list and then click the v button to enter the Permission settings interface as shown in Figure 13 7 174 User Manual of DS 7600NI Series NVR Permission Remote Configuration Camera Configuration B Local Log Search Local Parameters Settings B Local Camera Management BLocal Advanced Operation B Local Shutdown Reboot Cancel Figure 13 7 User Permission Settings Interface 6 Set the operating permission of Local Configuration Remote Configuration and Camera Configuration for the user Local Configuration Local Log Search Searching and viewing logs and system information of NVR Local
59. Parameters Settings Configuring parameters restoring factory default parameters and importing exporting configuration files Local Camera Management The adding deleting and editing of IP cameras Local Advanced Operation Operating HDD management initializing HDD setting HDD property upgrading system firmware clearing I O alarm output Local Shutdown Reboot Shutting down or rebooting the NVR Remote Configuration Remote Log Search Remotely viewing logs that are saved on the NVR Remote Parameters Settings Remotely configuring parameters restoring factory default parameters and importing exporting configuration files Remote Camera Management Remote adding deleting and editing of the IP cameras Remote Serial Port Control Configuring settings for RS 232 and RS 485 ports Remote Video Output Control Sending remote button control signal Two Way Audio Realizing two way radio between the remote client and the NVR Remote Alarm Control Remotely arming notify alarm and exception message to the remote client and controlling the alarm output Remote Advanced Operation Remotely operating HDD management initializing HDD setting HDD property upgrading system firmware clearing I O alarm output Remote Shutdown Reboot Remotely shutting down or rebooting the NVR Camera Configuration Remote Live View Remotely viewing live video of the selected camera s Local Manual Operation Locally starting stopping manual recording
60. Read only Redundancy Group REE PEE FEE CEE FEE LEE Fi EEE EDE DIE EPE SFE ECE FEE Ble 931 51GB Figure 5 31 HDD General Editing Note To edit HDD property you need to set the storage mode of the HDD to Group See Chapter Managing HDD Group 3 Set the HDD property to Read only 4 Click OK to save settings and back to the upper level menu Notes 1 You can t save any files in a Read only HDD If you want to save files in the HDD change the property to R W 2 If there is only one HDD and is set to Read only the NVR can t record any files Only live view mode is available 3 If you set the HDD to Read only when the NVR is saving files in it then the file will be saved in next R W HDD If there is only one HDD the recording will be stopped 73 User Manual of DS 7600NI Series NVR Chapter 6 Playback 74 User Manual of DS 7600NI Series NVR 6 1 Playing Back Record Files 6 1 1 Playing Back by Channel Purpose Play back the recorded video files of a specific channel in the live view mode Channel switch is supported OPTION 1 Choose a channel in live view mode using the mouse and click the button in the quick setting toolbar Note In the instant playback mode only record files recorded during the last five minutes on this channel will be played back Figure 6 1 Instant Playback Interface OPTION 2 1 Enter the Playback interface Mouse right click a channel in
61. Search Playback Note The GERPZ i FARR Ferree PUPeEReEwLy indicates the start end time of the record Table 6 5 Detailed aU of o Toolbar Audio on Start Stop f da 30s forward EN 30s reverse Mute clipping Add default at ad Speed down tag customized tag management Pause reverse Pause play play Scaling Play Reverse play up down the CS Speed up Single frame Single frame time line play reverse play Smart search Process bar result Note Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames 89 User Manual of DS 7600NI Series NVR 6 2 3 Digital Zoom Steps 1 Click the button on the playback control bar to enter Digital Zoom interface 2 Use the mouse to draw a red rectangle and the image within it will be enlarged up to 16 times Figure 6 26 Draw Area for Digital Zoom 3 Right click the image to exit the digital zoom interface 6 2 4 Reverse Playback of Multi channel Purpose You can play back record files of multi channel reversely Up to 8 ch with 4CIF resolution simultaneous adverse playback is supported up to 4 ch with 720P resolution simultaneous adverse playback is supported up to 2 ch with 1080P resolution and up to 1 ch with SMP resolution reverse playback is supported Steps 1 Enter Playback interface Menu gt Playback 2 Check more than one checkboxes to select multiple channels and click to select
62. W HDD quota management different capacity can be assigned to different channel Recording and Playback Holiday recording schedule configuration Continuous and event video recording parameters Multiple recording types manual normal alarm motion motion alarm motion amp alarm 8 recording time periods with separated recording types Pre record and post record for alarm motion detection for recording and pre record time for schedule and manual recording Searching record files by events alarm input motion detection Tag adding for record files searching and playing back by tags Locking and unlocking record files Local redundant recording Searching and playing back record files by channel number recording type start time end time etc Smart search for the selected area in the video User Manual of DS 7600NI Series NVR Backup Zooming in when playback Reverse playback of multi channel Supports pause play reverse speed up speed down skip forward and skip backward when playback and locating by dragging the mouse Up to 8 ch synchronous playback at 4CIF real time Export video data by USB or SATA device Export video clips when playback Management and maintenance of backup devices Alarm and Exception Configurable arming time of alarm input output Alarm for video loss motion detection tampering abnormal signal video input output standard mismatch illegal login network disconnected
63. a date on the calendar 90 User Manual of DS 7600NI Series NVR Normal Camera iPCamera 01 iPCamera 02 iPCamera 03 EACamera01 lm CiPCamera 05 faiPCamera 06 f4 Camera01 PCamera 08 iPCamera 09 iPCamera 10 iPCamera 11 e iPCamera 12 H iPCamera 13 Figure 6 27 4 ch Synchronous Playback Interface 3 Click pe to play back the record files reversely 91 User Manual of DS 7600NI Series NVR Chapter 7 Backup 92 User Manual of DS 7600NI Series NVR 7 1 Backing up Record Files 7 1 1 Quick Export Purpose Export record files to backup device s quickly Steps 1 Enter Video Export interface Menu gt Export gt Normal Choose the channel s you want to back up and click Quick Export button Note 1 The time duration of record files on a specified channel cannot exceed one day Otherwise the message box Max 24 hours are allowed for quick export will pop up 2 The number of channels for synchronous export cannot exceed 4 Otherwise the message box Max 4 channels are allowed for synchronous quick export will pop up ZIP Camera Dy Dae 1D ee 1B 0 7 05 2013 16 48 08 08 05 2013 00 48 18 All All 07 05 2013 00 00 00 0 7 05 2013 23 59 59 Figure 7 1 Quick Export Interface 2 Click the Export button to start exporting Note Here we use USB Flash Drive and please refer to the next section Normal Backup for more backup devices suppo
64. a of Playback by event Toolbar Audio on Start Stop 30s forward EH 30s reverse Mute clipping Add default Tag is i EKI Speed down tag customized tag management Pause reverse Pause play play Sie Scaling ay Reverse play gpg up down the a Speed up Single frame Single frame time line play reverse play CO a a Note Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames 6 1 4 Playing Back by Tag Purpose Video tag allows you to record related information like people and location of a certain time point during playback You are also allowed to use video tag s to search for record files and position time point Before playing back by tag 1 Enter Playback interface Menu gt Playback 2 Search and play back the record file s Refer to Chapter 6 1 1 for the detailed information about searching and playback of the record files 81 User Manual of DS 7600NI Series NVR Normal Ccamera iPCamera 01 iPCamera 02 iPCamera 03 M Camera01 iPCamera 05 iPCamera 06 MIPCamera 08 iPCamera 09 iPCamera 10 iPCamera 11 iPCamera 12 iPCamera 13 lt SS005 ElS slo s _ ja ejej L ISJSl jo o 04 25 2013 10 00 12 04 25 2013 16 02 59 aA 8 Figure 6 13 Interface of Playback by Time Click button to add default tag Click button to add customized tag and input tag name Note Max 64 tags can be added to a s
65. age displayed on the monitor after starting up normally Possible Reasons a No VGA or HDMI connections b Connection cable is damaged c Input mode of the monitor is incorrect Steps 1 Verify the device is connected with the monitor via HDMI or VGA cable If not please connect the device with the monitor and reboot 2 Verify the connection cable is good If there is still no image display on the monitor after rebooting please check if the connection cable is good and change a cable to connect again 3 Verify Input mode of the monitor is correct Please check the input mode of the monitor matches with the output mode of the device e g if the output mode of NVR is HDMI output then the input mode of monitor must be the HDMI input And if not please modify the input mode of monitor 4 Check if the fault is solved by the step 1 to step 3 If it is solved finish the process If not please contact the engineer from Hikvision to do the further process e There is an audible warning sound Di Di Di DiDi after a new bought NVR starts up Possible Reasons a No HDD iis installed in the device b The installed HDD has not been initialized c The installed HDD is not compatible with the NVR or is broken down Steps 1 Verify at least one HDD 1s installed in the NVR 1 Ifnot please install the compatible HDD Note Please refer to the Quick Operation Guide for the HDD installation steps 2 If you don
66. ameras 7 Click the OK button to finish the Copy settings and back to the Storage Mode interface 8 Click the Apply button to apply the settings Note If the quota capacity is set to 0 then all cameras will use the total capacity of HDD for record 148 User Manual of DS 7600NI Series NVR 10 5 Checking HDD Status Purpose You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case of HDD failure Checking HDD Status in HDD Information Interface Steps 1 Enter the HDD Information interface Menu gt HDD gt General 2 Check the status of each HDD which is displayed on the list as shown in Figure 10 18 931 5166 4666 Figure 10 18 View HDD Status 1 Note If the status of HDD is Normal or Sleeping it works normally If the status is Uninitialized or Abnormal please initialize the HDD before use And if the HDD initialization is failed please replace it with a new one Checking HDD Status in HDD Information Interface Steps 1 Enter the System Information interface Menu gt Maintenance gt System Info 2 Click the HDD tab to view the status of each HDD displayed on the list as shown in Figure 10 19 149 User Manual of DS 7600NI Series NVR Label Status Capacity Free Space Property Type Group 1 Normal 931 51GB 928GB RAV Local 1 931 51GB 928GB Figure 10 19 View HDD Status 2 150 User Manual of DS 7600NI Series NVR 10 6 HDD Detection P
67. and alarm output of the selected camera s Remote Manual Operation Remotely starting stopping manual recording and alarm output of the selected camera s Local Playback Locally playing back recorded files of the selected camera s Remote Playback Remotely playing back recorded files of the selected camera s Local PTZ Control Locally controlling PTZ movement of the selected camera s 175 User Manual of DS 7600NI Series NVR e Remote PTZ Control Remotely controlling PTZ movement of the selected camera s e Local Video Export Locally exporting recorded files of the selected camera s 7 Click the OK button to save the settings and exit interface Note Only the admin user account has the permission of restoring factory default parameters 13 4 2 Deleting a User Steps 1 Enter the User Management interface Menu gt Configuration gt User 2 Select the user to be deleted from the list as shown in Figure 13 8 Admin 00 00 00 00 00 00 Figure 13 8 User List 3 Click the o icon to delete the selected user 13 4 3 Editing a User Steps 1 Enter the User Management interface Menu gt Configuration gt User 2 Select the user to be edited from the list as shown in Figure 13 8 3 Click the LA icon to enter the Edit User interface as shown in Figure 13 9 Note The admin user can also be edited 176 User Manual of DS 7600NI Series NVR Edit User Operator 00 00 00 00 00 Cancel
68. b site and associated web server that one is communicating with which protects against Man in the middle attacks Perform the following steps to set the port number of https Example If you set the port number as 443 and the IP address is 192 0 0 64 you may access the device by inputting https 192 0 0 64 443 via the web browser Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the More Settings tab to enter the More Settings interface as shown in Figure 9 14 3 Check the checkbox of Enable HTTPS 130 User Manual of DS 7600NI Series NVR nable HTTPS HIPS Por Figure 9 19 HTTPS Settings Menu Enter the HTTPS Port Click the Apply button to save and exit the interface 9 2 10 Configuring Email Purpose The system can be configured to send an Email notification to all designated users if an alarm event is detected etc an alarm or motion event is detected or the administrator password is changed Before configuring the Email settings the NVR must be connected to a local area network LAN that maintains an SMTP mail server The network must also be connected to either an intranet or the Internet depending on the location of the e mail accounts to which you want to send notification Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network Set the IPv4 Address IPv4 Subnet Mask IPv4 Gateway and the Preferred DNS Server in the Net
69. ce Note The device name can only contain the lower case English letter numeric and and it must start with the lower case English letter and cannot end with Access the Device via Web Browser or Client Software After having successfully registered the device on the HiDDNS server you can access your device via web browser or Client Software with the Device Domain Name Device Name Task 1 Access the Device via Web Browser Open a web browser and enter http www hik online com alias in the address bar Alias refers to the Device Domain Name on the device or the Device Name on the HiDDNS server Example http www hik online com nvr Note If you mapped the HTTP port on your router and changed it to port No except 80 you have to enter http www hik online com alias HTTP port in the address bar to access the device You can refer to Chapter 9 2 10 for the mapped HTTP port No Task 2 Access the devices via iVMS4200 For iVMS 4200 in the Add Device window select MIDONS and then edit the device information Nickname Edit a name for the device as you want Server Address www hik online com Device Domain Name It refers to the Device Domain Name on the device or the Device Name on the HiDDNS server you created User Name Enter the user name of the device By default it is admin Password Enter the password of the device By default it is 12345 126 User Manual of DS 7600NI Series NVR Adding Mode IP Doma
70. cececceeeeaeseenseseeeeeceeeeeeeeeeeaeeees 120 Chapter 9 Network Settna S snaa 121 Od Conneurnne General Se COM OS aea ea a anaraieneedgcie a bees setaney ae 122 O22 MConheuriny Advanced Setini gusan e nares ER E amano E EEE R 123 9 2 1 Commouring PPPOE SENS S enner en EOR 123 9 22 Combeuri ne DDN Sorensen A E tb Seausealeess 123 9 2 3 ConmmenutineiN TPSC Vei assim dtaatia nubian a 127 9 2 4 Consun SNM Poo fart cs Sih saree ss datreca a E ainda yecaldcauetanaeatn lobuaascaeess 128 9 2 5 Configuring Remote Alarm Host ii ssid ciisancatannsiatanisaiwiinn teeta eee 128 9 2 6 Coniemine MICAS Coa suisse ch canerids acces aes dacesan es aurea seaucer dase ateitecdem dees 129 9 2 1 Conanin RTS Peserai a a S 129 9 2 8 Configuring Server and HTTP Ports cccccccccccccccceeesssesseseeccccccceeeeeaaeeeeessseseeees 130 10 User Manual of DS 7600NI Series NVR 9 2 9 Commeurime Hl Bs P Ot sicts hctutaaes ta mectat midi te bate aed Oa bath aniae i itera tates 130 9 2 10 COMMCUTING Ema lesa a a ilelceusaiesh sti desoeuselocbiueieedes 131 9 2 11 Go ali 24 00 0162 UPOP eee ar meena penne Meena trent ie Beiter c pent Mite RCE nr pent mie mest nC pOeTe Serene en 132 9 2 12 Configuring High speed Download sicscssuscs c cick ereaseicioenaicessaiarnaticaralneinedieanens 134 Od Clieciciie NeMoN Trail Oeae aa OA sataeead adaatein aang EOE 135 94 Contioutine Network Dele CHOM xcssvisccvenievecneivacccusalevutnn Silk E e a i 136 9 4 1 Testne Network Delay
71. ch Result interface of record files 104 User Manual of DS 7600NI Series NVR Menu gt Export gt Normal Set search condition and click Search button to enter Search Result interface Note At least one channel shall be selected ZJ IP Camera Dy ee DA 1D eee DE 07 05 2013 16 48 08 08 05 2013 00 48 18 All All 07 05 2013 00 00 00 0 7 05 2013 23 59 59 Figure 7 29 Normal Video Search for Backup 2 Select record files you want to back up Click Export button to enter Export interface Note At least one record file shall be selected Search result 10 20 2011 11 50 24 15 23 54 1 038 237KB 10 20 2011 15 23 54 16 11 53 399 657KB 10 20 2011 10 33 53 11 17 18 692 336KB 10 20 2011 11 1 18 11 18 52 25 163KB 10 20 2011 13 13 10 14 16 30 1 013 691KB 10 20 2011 14 16 30 15 21 25 1 038 801KB 2 10 20 2011 15 21 25 16 11 23 722 552KB BESEEEEBEEBEBABS PLL pr 10 20 2011 10 33 51 11 18 56 668 672KB HDD 5 Start time 10 20 2011 09 08 52 End time 10 20 2011 11 50 24 Total size 6 482MB Cancel Figure 7 30 Result of Normal Video Search for Backup 3 Backup device management Click Erase button if you want to erase the files from a re writable CD DVD Note There must be a re writable CD DVD when you make this operation Note If the inserted USB writer or DVD R W is not recognized e Click the Refresh button e Reconnect device e Check for compa
72. d of ping 792 168 0 0 1 1472 f the IP address may change according to the real condition and check if there exists packet loss Note Simultaneously press Ctrl and C to exit the ping command 2 Check the parameters of Main Stream Normal and Main Stream Event Select Menu gt Record gt Parameters gt Record and set the resolution of Main Stream Event the same as the one of Main Stream Normal 3 Verify the frame rate is real time frame rate Select Menu gt Record gt Parameters gt Record and set the Frame rate to Full Frame 4 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from Hikvision to do the further process Live view stuck when video output remotely via the Internet Explorer or platform software Possible Reasons a Poor network between NVR and IPC and there exists packet loss during the transmission 182 User Manual of DS 7600NI Series NVR b Poor network between NVR and PC and there exists packet loss during the transmission c The performances of hardware are not good enough including CPU memory etc Steps 1 Verify the network between NVR and IPC is connected 1 When image is stuck connect the RS 232 ports on PC and the rear panel of NVR with the RS 232 cable 2 Open the Super Terminal and execute the command of ping 792 168 0 0 1 1472 f the IP address may change according to the r
73. disable the built in switch interface by selecting the manual while the current channel can be used as a normal channel and the parameters can also be edited Edit IP Camera D1 Manual 172 6 23 100 HIKVISION 8000 Cancel Figure 2 28 Edit IP Camera Interface Manual 3 Click the Apply button to finish adding 38 User Manual of DS 7600NI Series NVR Chapter3 Live View 39 User Manual of DS 7600NI Series NVR 3 1 Introduction of Live View Live view shows you the video image getting from each camera in real time The NVR automatically enters Live View mode when powered on Live View Icons In the live view mode there are icons at the right top of the screen for each channel showing the status of the record and alarm in the channel so that you can know whether the channel is recorded or whether there are alarms occur as soon as possible Table 3 1 Description of Live View Icons Icons Description Alarm video loss tampering motion detection or sensor alarm Record manual record schedule record motion detection or alarm triggered record Alarm amp Record 40 User Manual of DS 7600NI Series NVR 3 2 Operations in Live View Mode In live view mode there are many functions provided The functions are listed below Single Screen showing only one screen on the monitor Multi screen showing multiple screens on the monitor simultaneously Auto switch the screen is auto switched to the
74. e Follow the procedure to configure alarm triggered recording Steps 1 Enter the Alarm setting interface Menu gt Configuration gt Alarm Alarm Input Alarm Output Alarm Input List Alarm Input No Alarm Name Alarm Type 172 6 23 105 8000 lt 1 N O Alarm Output List Alarm Output No Alarm Name Dwell Time 172 6 23 105 8000 gt 1 5S Figure 5 15 Alarm Settings 2 Click the Alarm Input tab Alarm Status Alarm Output Alarm Input No 172 6 23 105 8000 lt 1 Alarm Name i ji ype Figure 5 16 Alarm Settings Alarm Input 1 Select Alarm Input number and configure alarm parameters 2 Choose N O normally open or N C normally closed for alarm type 3 Check the checkbox of Enable 4 Click Settings 64 User Manual of DS 7600NI Series NVR Settings Arming Schedule Linkage Action PTZ Linking IP Camera D1 D2 Cancel Figure 5 17 Alarm Settings 5 Choose the alarm triggered recording channel 6 Check the checkbox to select channel 7 Click Apply to save settings 8 Click OK to back to the upper level menu Repeat the above steps to configure other alarm input parameters If the settings can also be applied to other alarm inputs click Copy and choose the alarm input number Copy Alarm Input to BAlarm Input No Alarm Name 172 6 23 105 8000 lt M1 72 6 23 105 3000 lt 2 Cancel Figure 5 18 Copy Alarm Input 3 Edit the Alarm triggered record in the Record Schedule setting int
75. e Pause play play Scaling Play Dg Reverse play up down the co Speed up Single frame Single frame time line play reverse play oof ot Lo _ Note Playback progress bar use the mouse to click any point of the progress bar or drag the progress bar to locate special frames 6 1 5 Playing Back by System Logs Purpose Play back record file s associated with channels after searching system logs Steps 1 Enter Log Information interface Menu gt Maintenance gt Log Information 2 Click Log Search tab to enter Playback by System Logs Set search time and type and click Search button et aera All All Figure 6 18 System Log Search Interface 3 Choose a log with record file and click button to enter Playback interface Note If there is no record file at the time point of the log the message box No result found will pop up 84 User Manual of DS 7600NI Series NVR T Operation T Operation A Exception A Exception A Exception A Exception A Exception 2 3 4 5 6 7 8 9 A Exception Operation T Operation A Exception Operation Figure 6 19 Result of System Log Search 4 Playback interface The toolbar in the bottom part of Playback interface can be used to control playing process Figure 6 20 Interface of Playback by Log 06 18 2012 06 18 2012 All All 06 18 2012 09 42 51 06 18 2012 09 42 51 06 18 2012 09 43 35 06 18 2012 09 43 46 06 18 2012 09 43 53 06 18 2012 09 43 59 0
76. e usage F1 Button Select all items on the list when used in a list field In PTZ Control mode it will turn on off PTZ light if applicable In Playback mode it is used to switch between play and reverse play Buttons to adjust the iris focus and zoom of a PTZ camera F2 Button Cycle through tab pages In synchronous playback mode it is used to switch between channels Troubleshooting Remote Control 13 14 15 16 17 8 1 Note Make sure you have installed batteries properly in the remote control And you have to aim the remote control at the IR receiver in the front panel If there is no response after you press any button on the remote follow the procedure below to troubleshoot Steps 16 User Manual of DS 7600NI Series NVR 1 2 3 4 5 Go to Menu gt Settings gt General gt More Settings by operating the front control panel or the mouse Check and remember NVR ID The default D is 255 This ID is valid for all the IR remote controls Press the DEV button on the remote control Enter the NVR ID you set in step 2 Press the ENTER button on the remote If the Status indicator on the front panel turns blue the remote control is operating properly If the Status indicator does not turn blue and there is still no response from the remote please check the following 1 Batteries are installed correctly and the polarities of the batteries are not reversed 2 Batteries are fresh and
77. eal condition and check if there exists packet loss Note Simultaneously press Ctrl and C to exit the ping command 2 Verify the network between NVR and PC is connected 1 Open the cmd window in the Start menu or you can press windows R shortcut key to open it 2 Use the ping command to send large packet to the NVR execute the command of ping 192 168 0 0 l 1472 f the IP address may change according to the real condition and check if there exists packet loss Note Simultaneously press Ctrl and C to exit the ping command 3 Verify the hardware of the PC is good enough Simultaneously press Ctrl Alt and Delete to enter the windows task management interface as shown in the following figure File Options View Help Leese Processes Services Performance Networking Users CPU Usage CPU Usage History Memory Physical Memory Usage History Physical Memory MB System Total Handles 21916 Cached l Threads 1107 Available Processes 73 Free Up Time 0 11 57 41 Commit MB 1463 6119 Kernel Memory MB Paged Nonpaged Resource Monitor L Processes 73 CPU Usage 35 Physical Memory 39 Windows task management interface Select the Performance tab check the status of the CPU and Memory If the resource is not enough please end some unnecessary processes 4 Check 1f the fault is solved by the above steps If it is solved finish the process If not please contact the
78. ect device e Check for compatibility from vendor You can also format USB flash drives or USB HDDs via the device 95 User Manual of DS 7600NI Series NVR 267MB File 280MB File 4 423KB File 127MB File 110MB File 18 367KB File 37 305KB File 608KB File 06 23 2011 20 15 02 06 23 2011 20 11 14 06 23 2011 20 11 20 06 23 2011 20 12 12 06 23 2011 20 12 54 06 23 2011 20 13 02 06 23 2011 20 13 12 06 23 2011 20 09 40 E ch03_201106230000C ch03_2011062304293 E ch03_201106230914C B ch03_ 2011062309237 BH chO3_ 2011062311332 E ch03_201106231328C B ch03_2011062313474 D O O 9 939 B player exe New Folder Format Cancel Figure 7 7 Export by Normal Video Search using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop up message box Export finished Export finished Figure 7 8 Export Finished 5 Check backup result Choose the record file in Export interface and click button to check it Note The Player player exe will be exported automatically during record file export Export Refresh 06 23 2011 20 07 22 06 23 2011 20 07 28 06 23 2011 20 07 58 06 23 2011 20 07 36 06 23 2011 20 15 02 06 23 2011 20 11 14 06 23 2011 20 11 20 Folder Folder OKB File OKB File 26 MB File 280MB File 4 423KB File Export record files to me B Welcome to use backup E ch03_ 20110623000000 E ch03_20110623042932 E ch03_20110623091403 JO OOAOO I Ich 4
79. ect the network cameras which are not configured with the standard protocols you can configure the customized protocols for them Steps 1 Click the Protocol button in the Add IP Camera Custom interface to enter the protocol management interface 34 User Manual of DS 7600NI Series NVR Protocol Management Costume Protoco Custom Protocol 1 Protocol Name ipc Stream Type Main Stream Substream Enable Substream Type RTSP RTSP lransfer Protoco Auto Auto Port 554 554 Path Example Type IP Address Port Path rtsp 192 168 0 1 554 ch1 mainfav_stream Figure 2 21 Protocol Management Interface There are 16 customized protocols provided in the system you can edit the protocol name and choose whether to enable the sub stream 2 Choose the protocol type of transmission and choose the transfer protocols Note The protocol type and the transfer protocols must be supported by the connected network camera After adding the customized protocols you can see the protocol name is listed in the dropdown list please refer to Figure 2 22 Custom Add IPC HIKVISION 8000 admin Protocol Search Figure 2 22 Protocol Setting 3 Choose the protocols you just added to validate the connection of the network camera 2 3 3 Editing IP cameras connected to the PoE interfaces Only for DS 7600NI SE P and DS 7600NI VP series NVR The PoE interfaces enables the NVR system to pass electrical power safely a
80. edule of other days of a week You can also use Copy button to copy an arming schedule to other days 5 Click the OK button to complete the video loss settings of the channel 114 User Manual of DS 7600NI Series NVR 8 4 Detecting Video Tampering Alarm Purpose Trigger alarm when the lens is covered and take alarm response action s Steps 1 Enter Video Tampering interface of Camera Management and select a channel you want to detect video tampering Menu gt Camera gt Video Tampering IP Camera 1 Figure 8 11 Video Tampering Setup Interface 2 Set the video tampering handling method of the channel Check the checkbox of Enable Video Tampering Drag the sensitivity bar and choose a proper sensitivity level Use the mouse to draw an area you want to detect video tampering Click button to set up handling method of video tampering IP Camera 1 Figure 8 12 Set Detection Area and Sensitivity of Video Tampering 3 Set arming schedule and alarm response actions of the channel 1 Click Arming Schedule tab to set the channel s arming schedule 2 Choose one day of a week and Max eight time periods can be set within each day 3 Click Apply button to save the settings Note Time periods shall not be repeated or overlapped 115 User Manual of DS 7600NI Series NVR Settings Linkage Action Mon 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 lt
81. eeese 24 2 24 Wsinie the Wizard for Dasic COMMOUTAN OM ceisir a a a a ea 26 23 Adding and Connecting the IP Cameras crisisen E EE T sed enestiwedern tates 30 2 3 1 Addins the Online IP Cameras ess wesacks reai e a a 30 232 Editing the Connected IP cameras and Configuring Customized Protocols 33 2 3 3 Editing IP cameras connected to the PoE interfaces Only for DS 7600NI SE P and DS O00NIEV P series NY R ii scorer adaa OEE TOEA nica sine O OTA ONEA 35 2 3 4 Editing IP cameras connected to the built in switch network interfaces Only for DS27 O00NESEN Series NVR herein eA EENS AEE NTEN ES NE A 37 Chapter 3 Live View oense eeann e Eo EO A a EE E N 39 Sel MnO tion OL LIVS VEW asci ie N E GA 40 aa QPerddons In bive View Mod enensiiea a Cab ediutarcdatedacsa yard uncats 41 Fal Usine the Mouse m Live Vie Weeaiiioi en EEA EA 41 3 2 2 Quick Setting Toolbar in Live View Mode csisrieccitinerccncis eects 42 Dio Aduse WAVE VIEW SCUIN OS sccercch cas a E eeiteas busied pensive A A 44 Dee WSC FTO SOU eaen us avio vas cetacean a veas ehanitin debian cuanieas einai eed tenuate mao Leesmraieae een ed acne 46 Chapter 4P TAC Ont ls soiis carcass eiies cacncecsasunwissassneiteassatesranueveas 47 Al e Onieunin PZ SCM OS tiersei niece telabsadiuen E tetacanaa asacivetumaaaneneeass 48 AD Setine PIZ Presets Patrols amp Paterissa a i iia 49 4 2 1 CUS CORMIA IMO Prese eaa a Cuabaedeemencedd Ocserieunaeke tener 49 4 2 2 Cale Prese S oa e
82. en choose Pattern on the control bar 3 Double click the pattern or select the pattern and click o to call it PTZ IE norena BEETS nnne ajajaja 4 Patrol O Figure 4 11 PTZ Toolbar Pattern 54 User Manual of DS 7600NI Series NVR 4 3 PTZ Control Toolbar In the Live View mode you can press the PTZ Control button on the front panel or on the remote control or choose the PTZ Control icon a to enter the PTZ toolbar Preset P gt 4 Patrol Figure 4 12 PTZ Toolbar Table 4 1 Description of the PTZ toolbar icons Description Icon Description Description aog Direction button and Zoom Focus ow Je E the auto cycle button Iris The speed of the l l Light on off Wiper on off Zoom Focus Iris PTZ movement ra Image 3D Zoom Preset Centralization z pattern movement Previous item windows 55 User Manual of DS 7600NI Series NVR Chapter 5 Record Settings 56 User Manual of DS 7600NI Series NVR 5 1 Configuring Recording Parameters Purpose By configuring the recording parameters you can define the parameters which affect the image quality such as the transmission stream type the resolution and so on Before you start 1 Make sure that the HDD has already been installed If not please install a HDD and initialize it Menu gt HDD gt General Figure 5 1 HDD General 2 Check the storage mode of the HDD 1 Click Advanced to check the storage mode of the HDD
83. encoders with multiple channels only check the checkbox of Channel No in the pop up window as shown in the following figure and click OK to finish adding 32 User Manual of DS 7600NI Series NVR Channel No E Channel No iv 1 v vE vE Figure 2 17 Selecting Multiple Channels 2 3 2 Editing the Connected IP cameras and Configuring Customized Protocols After the adding of the IP cameras the basic information of the camera lists in the page you can configure the basic setting of the IP cameras Steps 1 Click the icon to edit the parameters you can edit the IP address protocol and other parameters Edit IP Camera D1 172 6 23 124 HIKVISION 8000 1 admin Cancel Figure 2 18 Edit the Parameters 2 Click OK to save the settings and exit the editing interface To edit advanced parameters 1 Drag the horizontal scroll bar to the right side and click the icon 33 User Manual of DS 7600NI Series NVR Advance Set Password IP Camera No D5 IP Gamera Address 172 6 21 117 Manage Pon 8000 Figure 2 19 Network Configuration of the Camera 2 You can edit the network information and the password of the camera e ee e Advance Set Network F Camera M Curent Password Cancel Figure 2 20 Password Configuration of the Camera 3 Click Apply to save the settings and click OK to exit the interface Configuring the customized protocols Purpose To conn
84. era 41 User Manual of DS 7600NI Series NVR Menu Single Screen Multi screen Previous Screen Next Screen stan Auto switch Stan Recording Add IP Camera Playback Output Mode Figure 3 1 Right click Menu 3 2 2 Quick Setting Toolbar in Live View Mode On the screen of each channel there is a quick setting toolbar which shows when you single click the mouse in the corresponding screen E e Figure 3 2 Quick Setting Toolbar Table 3 3 Description of Quick oe Toolbar Icons Enable Disable Mute Audio on Manual Record Digital Zoom Image Settings Live View we Close Strategy Playback only shows the record in last five minutes If no record is found it means there is no record during the last five minutes mDigital Zoom can zoom in the selected area to the full screen You can click and draw to select the area to zoom in as shown in Figure 3 3 42 User Manual of DS 7600NI Series NVR Figure 3 3 Digital Zoom s You can set the image parameters like brightness contrast saturation and hue Image Settings icon can be selected to enter the Image Settings menu Image Settings Customize Figure 3 4 Image Settings Customize Live View Strategy can be selected to set strategy including Real time Balanced Fluency Live View Strategy Real time Balanced Fluency Figure 3 5 Live View Strategy 43 User Manual of DS 7600NI Series
85. erface 3 Select Trigger Channel tab and select one or more channels which will start to record or become full screen monitoring when an external alarm is input 4 Select Arming Schedule tab to set the channel s arming schedule Choose one day of a week and Max eight time periods can be set within each day Note Time periods shall not be repeated or overlapped 5 Select Linkage Action tab to set up alarm response actions of the alarm input please refer to Chapter 110 User Manual of DS 7600NI Series NVR Setting Alarm Response Actions Repeat the above steps to set up arming schedule of other days of a week You can also use Copy button to copy an arming schedule to other days Settings Trigger Channel Linkage Action PTZ Linking Mon 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 CAE SS JS SE JS SE Cancel Figure 8 6 Set Arming Schedule of Alarm Input 6 If necessary select PTZ Linking tab and set PTZ linkage of the alarm input Set PTZ linking parameters and click OK to complete the settings of the alarm input Note Please check whether the PTZ or speed dome supports PTZ linkage One alarm input can trigger presets patrol or pattern of more than one channel But presets patrols and patterns are exclusive Settings Trigger Channel Arming Schedule Linkage Action inking IP Camera 4 Figure 8 7 Set PTZ Linking of Alarm Input 7 If y
86. erface For the detailed information of schedule configuration see Chapter Configuring Record Schedule 65 User Manual of DS 7600NI Series NVR 5 5 Manual Record Purpose Follow the steps to set parameters for the manual record The manual recording is prior to the scheduled recording Steps 1 Enter the Manual settings interface Menu gt Manual Or press the REC button on the remote control IP Camera Recording by schedule Recording by manual operation Figure 5 19 Manual Record 2 Enabling Manual Record 1 Select Record on the left bar 2 Click the status button before camera number to change OFF to oni 3 Disable manual record Click the status button to change oN roll Note Green icon JON means that the channel is configured the record schedule After rebooting all the manual records enabled are canceled 66 User Manual of DS 7600NI Series NVR 5 6 Configuring Holiday Record Purpose Follow the steps to configure the record schedule on holiday for that year You may want to have different plan for recording on holiday Steps 1 Enter the Record setting interface Menu gt Record gt Holiday Holiday1 Enabled 1 Jan Holiday3 Disabled 1 Jan Holiday4 Disabled 1 Jan Holiday5S Disabled 1 Jan Holiday6 Disabled 1 Jan Holiday Disabled 1 Jan Holiday8 Disabled 1 Jan Holiday9 Disabled 1 Jan Holiday10 Disabled 1_Jan Holiday11 Disabled 1 Jan Holiday12 Disabled 1 Jan i i Be i i i i Be Be Figure 5
87. esets Patrols amp Patterns Before you start Please make sure that the presets patrols and patterns should be supported by PTZ protocols 4 2 1 Customizing Presets Purpose Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place Steps 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings General IP Camera 3 O Save Preset 5 alles alee ally ae pall alti rage e ee wae 1 14 TD 16 TT S Call Preset Pattern 1 fH oOo Patrol 1 Figure 4 2 PTZ More Settings 2 Use the directional button to wheel the camera to the location where you want to set preset 3 Click the round icon before Save Preset 4 Click the preset number to save the preset Repeat the steps2 4 to save more presets If the number of the presets you want to save is more than 17 you can click and choose the available numbers Preset Cancel Figure 4 3 More Presets 49 User Manual of DS 7600NI Series NVR 4 2 2 Calling Presets Purpose This feature enables the camera to point to a specified position such as a window when an event takes place Call preset in the PTZ setting interface Steps 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings 2 Check the round icon of Call Preset General More Settings IP Camera 3 Save Preset aleae ae a a 8 9 10 11 12 13 14 15 16 17 0 Call Preset 5 Patter
88. esm ens N EEA EER 179 TROUDICS ROO MIN aesan E sycnnes stad nas reed ad acnteen sha nae ed aes aa ane niehe ee meds bla mead teeaes eeama anu eaieks Senate 180 Summary OL CHANGES reon E E Sheela supl ean e lb tesueclevise 186 Erto Compatible IPC ammeras sicsict caren cureteial eactenanen telat era enatelabaneieeerate rab aiaea dene abannieioinetelaccsiaens 187 Listor Piikyistom IF Came asic cccce teri catch oecen E E ea dasecese A 187 histor hrd pary IPC amicras aa a Gebceteaueedteaeens 191 12 User Manual of DS 7600NI Series NVR Chapter 1 Introduction User Manual of DS 7600NI Series NVR 1 1 Front Panel HIKVISION OPOWER OSTATUS OTx Rx Figure 1 1 DS 7600NI SE N and DS 7600NI SE P Table 1 1 Description of Front Panel Power indicator turns yellow when system is running Status indicator blinks red when data is being read from or 1 Status Status TX RX indictor blinks yellow when network connection is Tx Rx functioning properly Universal Serial Bus USB ports for additional devices such as 2 USB Interface USB mouse and USB Hard Disk Drive HDD Figure 1 2 DS 7600NI V and DS 7600NI VP Table 1 2 Description of Front Panel The corresponding indicator blinks when the HDD is being read HDD Status Indicators l or written Panel Lock You can lock or unlock the panel by the key Running Status Indicator The indicator lights when the device is running Universal Serial Bus USB ports for additional d
89. evices such as 4 USB Interface USB mouse and USB Hard Disk Drive HDD 14 User Manual of DS 7600NI Series NVR 1 2 IR Remote Control Operations The NVR may also be controlled with the included IR remote control not supported with the DS 7600NI V and DS 7600NI VP series NVR shown in Figure 1 3 Note Batteries 2xAAA must be installed before operation Figure 1 3 Remote Control Table 1 3 Description of the Soft Keyboard Icons Enables Disables Remote Control Switch to the corresponding channel in Live view or PTZ Control mode Input numbers and characters in Edit mode Switch between different channels in All day Playback mode between different channels in All Switch between different channels in All day Playback mode Playback mode Edit text fields When editing text fields it will also function as a Backspace button to delete the character in front of the cursor A Button Adjust focus in the PTZ Control menu It is also used to switch between input methods upper and lowercase 15 User Manual of DS 7600NI Series NVR alphabet symbols and numeric input REC Button Enter the Manual Record setting menu In PTZ control settings press the button and then you can call a PTZ preset by pressing Numeric button It is also used to turn audio on off in the Playback mode 7 PLAY Button The button is used to enter the All day Playback mode It is also used to auto scan in the PTZ Control menu
90. ext button to enter the date and time settings window as shown in Figure 2 5 26 User Manual of DS 7600NI Series NVR GMT 08 00 Beijing Urumqi Singapore MM DD YYYY 05 08 2013 15 22 59 Previous Figure 2 5 Date and Time Settings 6 After the time settings click Next button which takes you back to the Network Setup Wizard window as shown in Figure 2 6 10M 100M 1000M Self adaptive E 172 6 23 188 255 255 255 0 NY oes eee Previous DS 76048 amp 7608 amp 7616NI SE and DS 7600NI V 10M 100M 1000M Self adaptive P z Ad W238 ett A IPv4 Subnet Mask Rieke Mia cn ga EL IPv4 Default Gateway 172 9 1141 1 Preferred DNS Server Alternate DNS Server Internal NIC IPv4 Ad 192 Previous DS 7600NI SE N DS 7600NI SE P and DS 7600NI VP Figure 2 6 Network Configuration 27 User Manual of DS 7600NI Series NVR Note For DS 7600NI SE N DS 7600NI SE P and DS 7600NI VP series NVR the internal NIC IPv4 address should be configured for the cameras connecting to the PoE network interfaces of the NVR 7 Click Next button after you configured the network parameters which takes you to the HDD Management window shown in Figure 2 7 Wizard Capacity Status Property Type Free Space 931 51GB Normal RAN Local 919GB Previous Figure 2 7 HDD Management 8 To initialize the HDD click the Init button Initialization removes all the data saved in the HDD 9 Click Next button to enter the Addin
91. g IP Camera interface 10 Click Search to find online IP Camera Select the IP camera to be added and click the Add button Wizard BNo IP Address Amount of Device Ty Protocol Manage F Search Previous Figure 2 8 Search for IP Cameras 11 Click Next button Configure the recording for the searched IP Cameras 28 User Manual of DS 7600NI Series NVR Wizard EEE IP Camera 1 Start Recording Normal Motion Detection Previous Figure 2 9 Record Settings 12 Click Copy to copy the settings to other channels as shown in Figure 2 10 Copy to Di MHD2 H8D3 HD4 HD5 MDs MD 7 ds Figure 2 10 Copy Record Settings 13 Click OK to complete the startup Setup Wizard 29 User Manual of DS 7600NI Series NVR 2 3 Adding and Connecting the IP Cameras 2 3 1 Adding the Online IP Cameras Purpose The main function of the NVR is to connect the network cameras and record the video got from it So before you can get a live view or record of the video you should add the network cameras to the connection list of the device Before you start Ensure the network connection is valid and correct For detailed checking and configuring of the network please see Chapter Checking Network Traffic and Chapter Configuring Network Detection OPTION 1 Steps 1 Right click the mouse when you in the live view mode to show the right click menu 2 Select Add IP Camera in the pop up menu and select Auto or Manual o
92. ibility WV SW316 ONVIF compatibility WV SP1OS5 ONVIF compatibility WV SF132 ONVIF compatibility WV SP102 ONVIF compatibility WV SP509 ONVIF compatibility WV SW559 ONVIF compatibility WV SW558 ONVIF compatibility WV SW355 ONVIF compatibility WV SW352 ONVIF compatibility WV SF342 ONVIF compatibility WV SF332 ONVIF Image data 1 05 Application 1 66 Image data 2 03 Application 1 66 Image data 1 03 Application 1 66 Image data 1 03 Application 1 66 Image data 1 03 Application 1 30 Image data 2 21 Application 1 30 Image data 2 21 Application 1 30 Image data 2 21 Application 1 66 Image data 1 04 Application 1 66 Image data 1 04 Application 1 66 Image data 1 06 Application 1 66 800x600 compatibility Image data 1 06 WV SF346 ONVIF Application 1 66 1280x960 mpatibility Image data 1 06 CO WV SP306H WV SP336H Application 1 34 1280x960 Image data 1 06 Application 1 06 1280x960 Image data 1 06 1 8 2 20120327 D5118 1280x960 2 9310 A 1 7852 1 8 2 20120327 PELCO IXE20DN AAXVUU2 A 1920x1080 2 9081 A 1 7852 x x J 3 J J F a al J a J J J g J a af is a F J 1 8 2 20120327 IX30DN ACFZHB3 EAP 2048x1536 x 2 9080 A 1 7852 See ae SNB 5000P V2 00_110727 1280x1024 ONVIF compatibility VCC HD2300P 2 03 02 1103 18 00 1920x1080 SANYO VCC HD2500P 2 02 02 110208 00 1920x1080 J Onl
93. ify that the SMTP server can be reached 6 Click Apply button to save the Email settings 7 You can click Test button to test whether your Email settings work The corresponding Attention message box will pop up Refer to 0 Attention Attention Email test succeeded Failed to send test email please check the parameters or network status Figure 9 21 Email Testing Attention 9 2 11 Configuring UPnP Purpose Universal Plug and Play UPnP can permit the device seamlessly discover the presence of other network devices on the network and establish functional network services for data sharing communications etc You can use the UPnP function to enable the fast connection of the device to the WAN via a router without port mapping Before you start If you want to enable the UPnP function of the device you must enable the UPnP function of the router to which your device is connected When the network working mode of the device is set as multi address the Default Route of the device should be in the same network segment as that of the LAN IP address of the router Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the UPnP tab to enter the UPnP interface Edit External Port Mapping IP Address Status Figure 9 22 UPnP Settings Interface 3 Check checkbox to enable UPnP 4 Select the Mapping Type as Manual or Auto in the drop down list Task1 Auto
94. in IP Segment IP Server HiDDNS Add Offline Device ServerAddress www hik online com Device Domain Name User Name Password Y Exportto Group Setthe device name as the group name and add all the channels connected to the device to the group Cancel Figure 9 11 Access Device via iVMS4200 5 Click Apply button to save and exit the interface 9 2 3 Configuring NTP Server Purpose A Network Time Protocol NTP Server can be configured on your NVR to ensure the accuracy of system date time Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the NTP tab to enter the NTP Settings interface as shown in Figure 9 12 Figure 9 12 NTP Settings Interface Check the Enable NTP checkbox to enable this feature Configure the following NTP settings e Interval Time interval between the two synchronizing actions with NTP server The unit is minute o NTP Server IP address of NTP server e NTP Port Port of NTP server 5 Click Apply button to save and exit the interface Note The time synchronization interval can be set from1 to 10080min and the default value is 60min If the NVR is connected to a public network you should use a NTP server that has a time synchronization function such as the server at the National Time Center IP Address 210 72 145 44 If the NVR is setup in a more customized network NTP software can be used to establish a NTP server used
95. ing the NVR to network the captured network data packet can be exported to USB flash disk and other local backup devices Steps 1 Enter the Network Traffic interface Menu gt Maintenance gt Net Detect 2 Click the Network Detection tab to enter the Network Detection interface 3 Select the backup device from the dropdown list of Device Name as shown in Figure 9 31 Note Click Refresh button if the connected local backup device cannot be displayed When it fails to detect 136 User Manual of DS 7600NI Series NVR the backup device please check whether it is compatible with the NVR You can format the backup device if the format is incorrect Network Delay Packet Loss Test LAN 172 6 23 6 Network Packet Export USB1 1 Refresh 172 6 21 64 2 40Kbps Export Figure 9 31 Export Network Packet 4 Click Export to start exporting 5 After the exporting is complete click OK to finish the packet export as shown in 0 Attention Packet exporting ITT i Packet export succeeded Figure 9 32 Packet Export Attention Note Up to 1M data can be exported each time 9 4 3 Checking the Network Status Purpose You can also check the network status and quick set the network parameters in this interface Steps Click Status button on the right bottom of the page Traic Hehyork Stal Network Delay Packet Loss Test Destination Address Mebwork Packel Expeort vice Man kondi 172 65 21 97 436K bps Nehw
96. ingle video file 3 Tag management Click Bouton to check edit and delete tag s Tag management 06 18 2012 11 0 38 Z 06 18 2012 11 07 38 A Cancel Figure 6 14 Tag Management Interface Steps 1 Select the Tag from the drop down list in the Playback interface 2 Choose channels edit start time and end time and then click Search to enter Search Result interface Keyw Note You can enter keyword in the textbox to search the tag on your command 82 User Manual of DS 7600NI Series NVR Camera Camera02 Camera 01 Camera03 Camera04 Camera05 IPCamera 06 IPCamera 07 iIPCamera 08 IPCamera 09 IPCamera 10 IPCamera 11 IPCamera 12 IPCamera 13 IPCamera 14 IPCamera 15 IPCamera 16 Keyw Start Time 2012 11 30 00 00 00 End Time 2012 11 30 23 59 59 Q Search 00 00 00 Figure 6 15 Video Search by Tag 3 Click button to play back the file You can click the Back button to back to the search interface Pre play and post play can be configured I Tag PRI i aS giihi Oe pej gt Total 5 P 1 1 Pre play 30s Post play 30s Back Figure 6 16 Interface of Playback by Tag 14 22 05 Figure 6 17 Toolbar of Playback by Tag 83 User Manual of DS 7600NI Series NVR Table 6 4 Detailed ase of Playback by a Toolbar Audio on Start Stop f 30s forward E 30s reverse Mute clipping Add default Tag I EKI Speed down tag customized tag management Pause revers
97. ion of all channels triggered by the selected alarm input 99 User Manual of DS 7600NI Series NVR Event Details 07 05 2013 16 50 26 16 54 26 14 044KB 07 05 2013 16 50 26 16 54 26 102 803KB a B Dane Start time 07 05 2013 16 50 26 End time 07 05 2013 16 54 26 Total 2 P 1 1 Total size 114MB Cancel Figure 7 17 Event Details Interface 4 Export Click the Export button and start back up If the inserted USB device is not recognized e Click the Refresh button e Reconnect device e Check for compatibility from vendor You can also format USB flash drive or USB HDDs via the device USB1 1 Refresh 11 Folder 06 23 2011 20 07 22 Ww Backup Folder 06 23 2011 20 07 28 w E Export record files to me OKB File 06 23 2011 20 07 53 wv New Folder Format Cancel Figure 7 18 Export by Event Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop up message Export finished 100 User Manual of DS 7600NI Series NVR Export finished Figure 7 19 Export Finished 5 Check backup result Note The Player player exe will be exported automatically during record file export Export USB1 1 Refresh E Export record files to me B Welcome to use backup E ch03 20110623000000 E ch03_20110623042932 E ch03_20110623091403 r ie 7 IUIBLZIZA Ichoz l JE A ch03_20110623113325 B ch03_20110623132800 Folder Folder OKB File OKB File
98. itialize the disk s No Figure 10 1 Message Box of Uninitialized HDD Click Yes button to initialize it immediately or you can perform the following steps to initialize the HDD Steps 1 Enter the HDD Information interface Menu gt HDD gt General Figure 10 2 HDD Information Interface 2 Select HDD to be initialized 3 Click the Init button Initialize Initialization will erase all data on the HDD A Continue Figure 10 3 Confirm Initialization 4 Select the OK button to start initialization MLabel Capacity Status Property Type Free Space Gro Edit Del Figure 10 4 Status changes to Formatting 5 After the HDD has been initialized the status of the HDD will change from Uninitialized to Normal 140 User Manual of DS 7600NI Series NVR MLabe l Capacity Status Property Type Free Space Gro Edit Del m1 931 51GB Normal RAV Local 931GB 1 A Figure 10 5 HDD Status Changes to Normal Note Initializing the HDD will erase all data on it 141 User Manual of DS 7600NI Series NVR 10 2 Managing Network HDD Purpose You can add the allocated NAS or disk of IP SAN to NVR and use it as network HDD Steps 1 Enter the HDD Information interface Menu gt HDD gt General 2 Click the Add button to enter the Add NetHDD interface as shown in Figure 10 6 Add NetHDD NetHDD 1 NAS NetHDD IP Address NetHDD Directory Cancel Figure 10 6 HDD Information Interface 3
99. k OK to save setting and back to upper level menu V Click Apply in the Record Schedule interface to save the settings Draw the schedule Click on the color icons you can choose the schedule type as continuous or event IP Camera 1 a 8 10 Event Motion Alarm MIA Musa None Note Operation is invalid when the number of time segments exceeds the limit 8 Figure 5 9 Draw the Schedule Descriptions of the color icons are shown in the figure below 60 User Manual of DS 7600NI Series NVR Normal recording Continuous Event Recording triggered by Motion athe Alarm Recording triggered by alarm Recording triggered by either motion or alarm MIA w M amp A Recording triggered by both motion and alarm Delete the set schedule None Figure 5 10 Descriptions of the color icons Click the Apply button to validate the settings If the settings can also be used to other channels click Copy and then choose the channel to which you want to copy Copy to MD2 M803 e Po e MO7 80s N WD10 MD11 PAF PIKES M014 M015 MD16 Figure 5 11 Copy Schedule to Other Channels 61 User Manual of DS 7600NI Series NVR 5 3 Configuring Motion Detection Record Purpose Follow the steps to set the motion detection parameters In the live view mode once a motion detection event takes place the NVR can analyze it and do many actions to handle it Enabling motion detection function can trigger certain channels to s
100. le cycling through the patrol The Duration refers to the time span to stay at the corresponding key point The Speed defines the speed at which the PTZ will move from one key point to the next KeyPoint KeyPoint 1 Cancel Figure 4 7 Key Point Configuration 5 Click OK to save the key point to the patrol 51 User Manual of DS 7600NI Series NVR Repeat the above steps to add more key points Click the ia icon to delete the corresponding key point and click the trash icon to delete all the key points Select a key point then click k or Lia button to adjust the order of the key points Save Presets Call Preset Pattern 1 oe ee gt ee Patrol 1 Preset 1 Preset Preset 3 Figure 4 8 Key Points Deletion 4 2 4 Calling Patrols Purpose Calling a patrol makes the PTZ to move according the predefined patrol path Calling patrol in the PTZ setting interface Steps 1 In the PTZ setting interface Menu gt Camera gt PTZ gt More Settings 2 Select the patrol number and then click to call the patrol 3 Click E to stop it Calling patrol in live view mode Steps 1 Press PTZ control on the front panel or on the remote or click PTZ Control icon a on the quick setting toolbar to show the PTZ control toolbar 2 Choose Patrol on the control bar 3 Double click the patrol or select the patrol and click o to call it 52 User Manual of DS 7600NI Series NVR PTZ jE DEDEDE
101. lease try the ping command on PC to check if the PC connects with the IPC 3 Verify the network between IPC and NVR is stable 1 When the IPC is offline connect PC and NVR with the RS 232 cable 2 Open the Super Terminal use the ping command and keep sending large data packages to the connected IPC and check if there exists packet loss Note Simultaneously press Ctrl and C to exit the ping command Example Input ping 172 6 22 131 l 1472 f 4 Verify the switch is not flow control Check the brand model of the switch connecting IPC and NVR and contact with the manufacturer of the switch to check if it has the function of flow control If so please turn it down 5 Check if the fault is solved by the step 1 to step 4 If it is solved finish the process If not please contact the engineer from Hikvision to do the further process 181 User Manual of DS 7600NI Series NVR No monitor connected with the NVR locally and when you manage the IPC to connect with the device by web browser remotely of which the status displays as Connected And then you connect the device with the monitor via VGA or HDMI interface and reboot the device there is black screen with the mouse cursor Connect the NVR with the monitor before startup via VGA or HDMI interface and manage the IPC to connect with the device locally or remotely the status of IPC displays as Connect And then connect the device with the CVBS and there is black screen eithe
102. linking status MTU sending receiving rate etc Steps 1 Enter the Network Traffic interface Menu gt Maintenance gt Net Detect 8 192Kbps Sending 121Kbps Receiving 5 385Kbps Figure 9 28 Network Traffic Interface 2 You can view the sending rate and receiving rate information on the interface The traffic data is refreshed every second 135 User Manual of DS 7600NI Series NVR 9 4 Configuring Network Detection Purpose You can obtain network connecting status of NVR through the network detection function including network delay packet loss etc 9 4 1 Testing Network Delay and Packet Loss Steps 1 Enter the Network Traffic interface Menu gt Maintenance gt Net Detect 2 Click the Network Detection tab to enter the Network Detection menu as shown in Figure 9 29 Network Delay Packet Loss Test LAN1 172 6 23 6 Network Packet Export Refresh 1726 21 64 2 789Kbps Export Figure 9 29 Network Detection Interface Enter the destination address in the text field of Destination Address 4 Click Test to start testing network delay and packet loss The testing result pops up on the window If the testing is failed the error message box will pop up as well Refer to Figure 9 30 Result Attention A Average delay 63 ms e The destination is unreachable Packet loss rate 0 Figure 9 30 Testing Result of Network Delay and Packet Loss 9 4 2 Exporting Network Packet Purpose By connect
103. list Plug and Play It means that the camera is connected to the PoE interface so in this case the parameters of the camera can t be edited The IP address of the camera can only be edited in the Network Configuration interface see Chapter 9 1 Configuring General Settings for detailed information IP Camera No Adding Method IP Camera Address Protocol Manage Por Channel No User Name Admin Password Edit IP Camera D1 Plug and Play 12 168 254 2 HIK VISION 8000 1 admin Cancel Figure 2 24 Edit IP Camera Interface Plug and Play Manual You can disable the PoE interface by selecting the manual while the current channel can be used as a normal channel and the parameters can also be edited 36 User Manual of DS 7600NI Series NVR Edit IP Camera D1 Manual 172 6 23 100 HIKVISION 8000 Cancel Figure 2 25 Edit IP Camera Interface Manual 3 Click the Apply button to finish adding 2 3 4 Editing IP cameras connected to the built in switch network interfaces Only for DS 7600NI SE N series NVR For DS 7600NI SE N series NVR the extra network interfaces provide a built in switch with plug and play function Example As for DS 7608NI SE N NVR when you want to connect 2 online cameras and connect 6 network cameras via built in switch interfaces you must disable 2 built in switch interfaces in the Edit IP camera panel To add Cameras for NVR via built in switch interfaces
104. live view mode and select Playback from the menu as shown in Figure 6 2 Menu Single Screen Multi screen Previous Screen Next Screen Start Auto switch Start Recording Add IP Camera Playback Output Mode Figure 6 2 Right click Menu under Live View Under multi screen live view mode the recorded files of the top left channel will be played back Note Pressing numerical buttons will switch playback to the corresponding channels during playback process 2 Playback management 15 User Manual of DS 7600NI Series NVR The toolbar in the bottom part of Playback interface can be used to control playing progress as shown in Figure 6 3 Normal Camera iPCamera 01 iPCamera 02 iPCamera 03 M Camera01 iPCamera 05 iPCamera 06 EiPCamera 08 a iPCamera 09 iPCamera 10 1 iPCamera 11 iPCamera 12 iPCamera 13 lt e s S o _ ele _ lelje BENKAS B S e SS00055 Sislelole 04 25 2013 10 00 12 04 25 2013 16 02 59 Figure 6 3 Playback Interface Click the channel s to execute simultaneous playback of multiple channels 04 25 2013 10 00 12 04 25 2013 16 02 59 Figure 6 4 Toolbar of Playback Note The WAREZ SLEi Zi ee ek ee ee indicates the start end time of the record Table 6 1 Detailed tT of Playback Toolbar Audio on Start Stop 30s forward EN 30s reverse Mute clipping Add default Add Tag g d Speed down tag customized
105. long with data on Ethernet cabling to the connected network cameras The DS 7600NI SE P and DS 7600NI VP series NVR provides up to 8 PoE interfaces which can connect to 8 35 User Manual of DS 7600NI Series NVR network cameras directly and if you disable the PoE interface you can also connect to the online network cameras And the PoE interface supports the Plug and Play function Example As for 7604NI SE P NVR when you want to connect 1 online camera and connect 3 network cameras via PoE interfaces you must disable PoE interface in the Edit IP camera panel To add Cameras for NVR supporting PoE function Before you start Connect the network cameras via the PoE interfaces Steps 1 Enter the Camera Management interface Main menu gt Camera gt Camera You can see the connected cameras are listed Cam Add De Status IP Camera Edit Camera Name Protocol Device Model D1 D2 BDE D4 D5 D6 D7 D8 192 168 254 2 IPCamera 01 HIKVISION 192 168 254 3 IPCamera 02 HIKVISION 192 168 254 4 IPCamera 03 HIKVISION 192 168 254 5 IPCamera 04 HIKVISION 192 168 254 6 IPCamera 05 HIKVISION 192 168 254 7 IPCamera 06 HIKVISION 192 168 254 8 IPCamera 07 HIKVISION 192 168 254 9 IPCamera 08 HIKVISION Figure 2 23 Camera List Note The cameras connecting to the PoE interface cannot be deleted in this menu 2 Click the A button and select the Adding Method in the drop down
106. m Information menu to view the alarm information as shown in Figure 12 4 No Alarm Name Alarm Type Alarm Status Triggered Can 172 6 23 126 8000 lt 1 N C Occur D1 D4 172 6 23 126 8000 gt 1 Not supported Used Figure 12 4 Alarm Information Interface 12 1 5 Viewing Network Information Steps 1 Enter the System Information interface Menu gt Maintenance gt System Info Click the Network tab to enter the Network Information menu to view the network information as shown in Figure 12 5 NIC LAN1 IPv4 Address 172 6 23 180 IPv4 Subnet Mask 255 255 255 0 IPv4 Default Gateway 172 6 23 1 IPv6 Address 1 fe80 240 48ff feb8 c566 64 IPv6 Address 2 IPv6 Default Gateway Preferred DNS Server 0 0 0 0 Alternate DNS Server 0 0 0 0 Enable DHCP Disabled Enable PPPOE Disabled PPPOE Address PPPOE Subnet Mask PPPOE Default Gateway Figure 12 5 Network Information Interface 160 User Manual of DS 7600NI Series NVR 12 1 6 Viewing HDD Information Steps 1 Enter the System Information interface Menu gt Maintenance gt System Info 2 Click the HDD tab to enter the HDD Information menu to view the HDD status free space property etc 12 2 Searching amp Export Log Files Purpose The operation alarm exception and information of the NVR can be stored in log files which can be viewed and exported at any time Steps 1 Enter the Log Search interface Menu gt Maintenance gt Log Search Log Export 0
107. n 1 fo 6 Patrol 1 Figure 4 4 PTZ Call Preset 3 Choose the preset number Call preset in live view mode Steps 1 Press the PTZ button on the front panel or click the PTZ Control icon a in the quick setting bar to enter the PTZ setting menu in live view mode Figure 4 5 PTZ Toolbar 50 User Manual of DS 7600NI Series NVR 2 Choose Camera in the list on the menu 3 Double click the preset in the Preset list to call it 4 2 3 Customizing Patrols Purpose Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving on to the next key point The key points are corresponding to the presets The presets can be set following the steps above in Customizing Presets Steps 1 Enter the PTZ Control interface Menu gt Camera gt PTZ gt More Settings 2 Select patrol number in the drop down list of patrol 3 Select the o under Patrol option box to add key points for the patrol General More Settings IP Camera 3 O Save Preset eee ce see ae na Call Preset pea err teen e eee TT ie 13 14 15 16 17 n AN Pattern 1 m7 as O Patrol 1 Add KeyPoint o o o Figure 4 6 PTZ Add Key Point 4 Configure key point parameters such as the key point No duration of staying for one key point and speed of patrol The key point is corresponding to the preset The Key Point No determines the order at which the PTZ will follow whi
108. n list of dwell time of an alarm output the alarm can be cleared only by clicking Clear button in the following interface Steps Select the alarm output you want to trigger or clear and make related operations Menu gt Manual gt Alarm Click Trigger Clear button if you want to trigger or clear an alarm output Click Trigger All button if you want to trigger all alarm outputs Click Clear All button if you want to clear all alarm output Alarm Output No Alarm Name Trigger 172 6 23 105 8000 gt 1 Yes Trigger All Clear All Back Figure 8 18 Clear or Trigger Alarm Output Manually 120 User Manual of DS 7600NI Series NVR Chapter 9 Network Settings 121 User Manual of DS 7600NI Series NVR 9 1 Configuring General Settings Purpose Network settings must be properly configured before you operate NVR over network Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the General tab 10M 100M 1000M Self adaptive jia 126 T233 2030 2000 20070 V2 0 9 231 fe80 8ee 7 48ff fe16 f73c 64 8c e 7 48 16 f7 3c 1500 10 1 7 88 10 1 7 77 10M 100M 1000M Self adaptive a 172 6 23 8 259 299299 0 12 6 T23 ee fe80 8ee 7 48ff fe16 f73c 64 8c e7 48 16 f7 3c 1500 10 1 7 88 10 1 7 77 192 168 254 1 DS 7600NI SE N DS 7600NI SE P and DS 7600NI VP Figure 9 1 Network Settings Interface 3 In the General Settings interface you can configure the following setti
109. n the list Note At least 2 hard disks must be installed on your NVR when you want to set a HDD to Redundancy and there is one HDD with R W property 146 User Manual of DS 7600NI Series NVR 10 4 Configuring Quota Mode Purpose Each camera can be configured with allocated quota for the storage of recorded files Steps 1 Enter the Storage Mode interface Menu gt HDD gt Advanced 2 Set the Mode to Quota as shown in Figure 10 15 Note The NVR must be rebooted to enable the changes to take effect Quota iP Camera 1 1 024MB 931 Free Quota Space 931 GB Figure 10 15 Storage Mode Settings Interface 3 Select a camera for which you want to configure quota 4 Enter the storage capacity in the text fields of Max Record Capacity GB as shown in Figure 10 16 Quota IP Camera 1 1 024MB 931 100 A Free Quota Space 831 q 1 2 3 CE a a es ae a ae ee Figure 10 16 Configure Record Quota 5 You can copy the quota settings of the current camera to other cameras if required Click the Copy button to enter the Copy Camera menu as shown in Figure 10 17 147 User Manual of DS 7600NI Series NVR Copy to Di D2 HD3 HD4 HD5 MDs MD7 D8 MDS DPI DES DILES MD12 MD13 PICHE MD15 MDi16 Cancel Figure 10 17 Copy Settings to Other Camera s 6 Select the camera s to be configured with the same quota settings You can also click the checkbox of IP Camera to select all c
110. n your demand ft Menu Single Screen 5 Multi screen Previous Screen gt Next Screen Q Star Auto switch Start Recording 8 Auto Playback T Manual Output Mode Figure 2 11 Right click Menu of Adding IP Camera Auto The device will add the detected IP cameras or encoders automatically by the default user name and password of administrator Add IP Camera Auto Cam Status IP Camera A Camera Name Protocol Device Model D2 172 6 23 65 Camera 01 HIKVISION NC KDO32 lt Adding succeeded Figure 2 12 Auto Adding IP Camera Interface Note If the user name and password is changed the auto adding of IP camera will be failed you may add it 30 User Manual of DS 7600NI Series NVR manually Manual Steps 1 To add the online cameras with same network segment 1 The detected online camera will be listed in the camera list as shown in the figure below IP Camera Management Cam Add De Status IP Camera Edit Camera Name Protocol Device Model D1 m 172 6 23 177 Fi Camera01 HIKVISION DS 2CD8464C C 172 6 23 65 E HIKVISION NC KDO32 gt Refresh Delete All Add All Custom Addi Net Receive Idle Bandwidth 37Mbps Figure 2 13 Manual Adding IP Camera Interface 2 Click the button to add the camera Explanation of the icons Explanation Explanation Edit basic parameters of the camera Add the detected IP camera The camera is connected you can The came
111. nced settings to Group before you set the HDD property to Redundant For detailed information please refer to Chapter 10 3 Managing HDD Group There should be at least another HDD which is in Read Write status 3 Enter the Record setting interface Menu gt Record gt Parameters 1 Select Record tab 69 User Manual of DS 7600NI Series NVR IP Camera 1 Main Stream Continuous Video amp Audio 704 576 4CIF Variable Medium Full Frame General 2048 1152 1920 Kbps 5s Figure 5 24 Record Parameters 2 Select Camera you want to configure in the drop down list 3 Check the checkbox of Redundant Record 4 Click Apply to save settings and back to the upper level menu Repeat the above steps for configuring other channels 70 User Manual of DS 7600NI Series NVR 5 8 Configuring HDD Group for Recording Purpose You can group the HDDs and save the record files in certain HDD group Steps 1 Enter HDD setting interface Menu gt HDD Figure 5 25 HDD General 2 Select Advanced on the left bar Group Quota Rei ord on arOUp Group MIP Camera MD1 Dra o Dr WD4 WdD5 Figure 5 26 Storage Mode Check whether the storage mode of the HDD is Group If not set it to Group For detailed information please refer to Chapter 12 4 Managing HDD Group 3 Select General in the left bar Click LA to enter editing interface 4 Configuring HDD group 1 Choose a group number for the HDD group
112. networks e DDNS Dynamic DNS is a method protocol or network service that provides the capability for a networked device such as a router or computer system using the Internet Protocol Suite to notify a domain name server to change in real time ad hoc the active DNS configuration of its configured hostnames addresses or other information stored in DNS e Hybrid DVR A hybrid DVR is a combination of a DVR and NVR e NTP Acronym for Network Time Protocol A protocol designed to synchronize the clocks of computers over a network e NTSC Acronym for National Television System Committee NTSC is an analog television standard used in such countries as the United States and Japan Each frame of anNTSC signal contains 525 scan lines at 60Hz e NVR Acronym for Network Video Recorder An NVR can be a PC based or embedded system used for centralized management and storage for IP cameras IP Domes and other DVRs e PAL Acronym for Phase Alternating Line PAL is also another video standard used in broadcast televisions systems in large parts of the world PAL signal contains 625 scan lines at 50Hz e PTZ Acronym for Pan Tilt Zoom PTZ cameras are motor driven systems that allow the camera to pan left and right tilt up and down and zoom in and out e USB Acronym for Universal Serial Bus USB is a plug and play serial bus standard to interface devices to a host computer 179 User Manual of DS 7600NI Series NVR Troubleshooting e No im
113. next one And you must set the dwell time for each screen on the configuration menu before enabling the auto switch Menu gt Configuration gt Live View gt General Start Recording continuous record and motion detection record are supported Output Mode select the output mode to Standard Bright Gentle or Vivid Playback playback the recorded videos for current day Add IP Camera The shortcut to add IP camera automatically or manually 3 2 1 Using the Mouse in Live View Table 3 2 Mouse Operation in Live View Enter the main menu of the system by right clicking the mouse Switch to the single full screen by choosing channel number from the Single Screen l dropdown list Adjust the screen layout by choosing from the dropdown list Switch to the previous screen Start Stop Auto switch Enable disable the auto switch of the screens Start Recording Start continuous recording or motion detection recording of all channels Add IP Camera Add IP camera automatically or manually Enter the playback interface and start playing back the video of the Playback selected channel immediately Four modes of output supported including Standard Bright Gentle Output Mode and Vivid Note The dwell time of the live view configuration must be set before using Start Auto switch Note If the corresponding camera supports intelligent function the Reboot Intelligence option is included when right clicking mouse on this cam
114. ngs NIC Type IPv4 Address IPv4 Gateway MTU and DNS Server If the DHCP server is available you can click the checkbox of DHCP to automatically obtain an IP address and other network settings from that server Note For the DS 7600NI SE N DS 7600NI SE P and DS 7600NI VP series NVR you need to configure the internal NIC address so that IP addresses are assigned to the cameras connected to the PoE or built in switch interfaces Note The valid value range of MTU is 500 9676 4 After having configured the general settings click Apply to save the settings 122 User Manual of DS 7600NI Series NVR 9 2 Configuring Advanced Settings 9 2 1 Configuring PPPoE Settings Purpose Your NVR also allows access by Point to Point Protocol over Ethernet PPPoE Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the PPPoE tab to enter the PPPoE Settings interface as shown in Figure 9 2 Figure 9 2 PPPoE Settings Interface 3 Check the PPPoE checkbox to enable this feature 4 Enter User Name Password and Confirm Password for PPPoE access Note The User Name and Password should be assigned by your ISP 5 Click Apply to save and exit the interface 6 After successful settings the system asks you to reboot the device to enable the new settings and the PPPoE dial up is automatically connected after reboot You can go to Menu gt Maintenance gt System Info gt Network interface to view the sta
115. not out of charge 3 IR receiver is not obstructed If the remote still can t function properly please change a remote and try again or contact the device provider 17 User Manual of DS 7600NI Series NVR 1 3 USB Mouse Operation A regular 3 button Left Right Scroll wheel USB mouse can also be used with this NVR To use a USB mouse 1 Plug USB mouse into one of the USB interfaces on the front panel of the NVR 2 The mouse should automatically be detected If in a rare case that the mouse is not detected the possible reason may be that the two devices are not compatible please refer to the recommended the device list from your provider The operation of the mouse Table 1 4 Description of the Mouse Control Single Click Live view Select channel and show the quick set menu Menu Select and enter Left Click Click and Drag PTZ control pan tilt and zoom Video tampering privacy mask and motion detection Select target area Digital zoom in Drag and select target area Live view Drag channel time bar Right Click Single Click Live view Show menu Menu Exit current menu to upper level menu Scroll Wheel Scrolling up Live view Previous screen Menu Previous item Scrolling down Live view Next screen Menu Next item 18 User Manual of DS 7600NI Series NVR 1 4 Input Method Description af2tata s e 7 e so olwlejalriyjujijole Aajs jojejejujsje e az xicjvjajnim Figure 1 4
116. ntinuous Event Motion Alarm MIA ET None Figure 5 5 Record Schedule 2 Choose the camera you want to configure 3 Select the check box after the Enable Schedule item 4 Click Edit button or click on the color icon under the edit button and draw the schedule line on the panel Edit the schedule I In the message box you can choose the day to which you want to set schedule Continuous 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Continuous Continuous Continuous Continuous Continuous Continuous Continuous Continuous Cancel Figure 5 6 Recording Schedule Interface You can click the g button to set the accurate time of the schedule II To schedule an all day recording check the checkbox after the All Day item 59 User Manual of DS 7600NI Series NVR All Day _ Continuous Starv End Time 00 00 00 00 Type Continuous stari End Time 00 00 00 Be Continuous Start End Time J0 00 00 00 Type Continuous Figure 5 7 Edit Schedule II To arrange other schedule leave the All Day checkbox blank and set the Start End time Note Up to 8 periods can be configured for each day And the time periods can t be overlapped each other Repeat the above edit schedule steps to schedule recording for other days in the week If the schedule can also be applied to other days click Copy Figure 5 8 Copy Schedule to Other Days IV Clic
117. o stop all the live view 3 Click the Apply button to save the setting 45 User Manual of DS 7600NI Series NVR 3 4 User Logout Purpose After logging out the monitor turns to the live view mode and if you want to do some operation you need to enter user name and password tog in again Steps 1 Enter the Shutdown menu Menu gt Shutdown Shutdown Shutdown Reboot Cancel Figure 3 8 Shutdown 2 Click Logout Note After you have logged out the system menu operation on the screen is invalid It is required to input a user name and password to unlock the system 46 User Manual of DS 7600NI Series NVR Chapter 4 PTZ Controls 47 User Manual of DS 7600NI Series NVR 4 1 Configuring PTZ Settings Purpose Follow the procedure to set the parameters for PTZ The configuring of the PTZ parameters should be done before you control the PTZ camera Steps 1 Enter the PTZ Settings interface Menu gt Camera gt PTZ IP Camera 4 HIKVISION 0 Address range 0 255 Figure 4 1 PTZ General 2 Choose the camera for PTZ setting in the Camera dropdown list 3 Enter the parameters of the PTZ camera Note All the parameters should be exactly the same as the PTZ camera parameters Example If the PTZ camera uses the protocol of DRAGON you should select DRAGON in the PTZ Protocol field 4 Click Apply button to save the settings 48 User Manual of DS 7600NI Series NVR 4 2 Setting PTZ Pr
118. or each HDD is 1 8 Click the OK button to confirm the settings Attention Regroup the cameras for HDD if the HDD group number is changed No Figure 10 13 Confirm HDD Group Settings 9 In the pop up Attention box click the Yes button to finish the settings 10 3 2 Setting HDD Property Purpose The HDD property can be set to redundancy read only or read write R W Before setting the HDD property please set the storage mode to Group refer to step1 4 of Chapter Setting HDD Groups A HDD can be set to read only to prevent important recorded files from being overwritten when the HDD becomes full in overwrite recording mode When the HDD property is set to redundancy the video can be recorded both onto the redundancy HDD and the R W HDD simultaneously so as to ensure high security and reliability of video data Steps 1 Enter the HDD Information interface Menu gt HDD gt General 2 Select HDD from the list and click the LA icon to enter the Local HDD Settings interface as shown in Figure 10 14 145 User Manual of DS 7600NI Series NVR Local HDD Settings HDD Property ORW Read only Redundancy Group EER VEE CE LEE LE LE TAR T TE EOR See See KEN Bee EEN Ai 931GB Cancel Figure 10 14 Set HDD Property 3 Set the HDD property to R W Read only or Redundancy 4 Click the OK button to save the settings and exit the interface 5 In the HDD Information menu the HDD property will be displayed i
119. ork Figure 9 33 Network status checking 137 User Manual of DS 7600NI Series NVR If the network is normal the following message box pops out Result Lid Network status is normal Figure 9 34 Network status checking result If the message box pops out with other information instead of this one you can click Network button to show the quick setting interface of the network parameters 9 4 4 Checking Network Statistics Purpose You can check the network status to obtain the real time information of NVR Steps 1 Enter the Network Detection interface Menu gt Maintenance gt Net Detection 2 Choose the Network Stat tab Remote Live View Obps Remote Playback Obps Net Receive Idle 10Mbps Net Send Idle 40Mbps Figure 9 35 Network Stat Interface 3 Check the bandwidth of IP Camera bandwidth of Remote Live View bandwidth of Remote Playback bandwidth of Net Receive Idle and bandwidth of Net Send Idle 4 You can click Refresh button to get the newest status 138 User Manual of DS 7600NI Series NVR Chapter 10 HDD Management 139 User Manual of DS 7600NI Series NVR 10 1 Initializing HDDs Purpose A newly installed hard disk drive HDD must be initialized before it can be used with your NVR Note A message box pops up when the NVR starts up if there exits any uninitialized HDD Attention Not all hard disks are initialized Initialization will erase all data on the disk Do you want to in
120. ork cameras from Brickcom and Bosch Appendix List of IP Cameras Compatible Updated 1 Optimize the method for adding encoder Chapter 2 3 1 2 Optimize the playback interface Chapter 6 186 User Manual of DS 7600NI Series NVR List of Compatible IP Cameras List of Hikvision IP Cameras Note For the list our company holds right to interpret Max Type Model Version Sub stream Audio Resolution C osoa vooon oman a 1 C isan varoo osaamf af a C isao varowanion osama t a 1 O osa vao om a 4 C oswa voso aaamt a 4 C isansa vaoo awwasef vf a C san verona ose vf 4 C osas varowanicon Sos a 4 psacorsewpsn varowanicon vanaom fa 1 oosa voeon oan vf 4 O oo vaoo rma C osos vroa f vy C owe vaoo rama 9 C osas veroon fea C osan voon f vy O oaa vosa eoo 9 HD Network Camera C saoe voaa ramon o S C oor voaa foa o S C osos veon foao o 1 DS 2CD752MF E DS 2CD852MF E 1600x1200 y y DS 2CD852F E DS 2CD862MF E 1280x960 y y DS 2CD8464F EI V4 1 0 build 130111 1280x960 Ds2cpsespHNFE varonad orn 1280000 DS 2CD763PF NF E V4 1 0 build 130111 1280x960 2 lt 2 rs rs rs 2 i lt lt n OO GO OO DG OG 2 2 lt 2e 2 2 2 lt e 2e lt 2 lt 2 ce eT me em em eT eT 2 DS 2CD763PF NF EI V4 1 0 build 130111 187 User Manual of DS 7600NI Series NVR Max Type Model Version Resolution DS 2CD7164 E V4
121. ou want to set handling action of another alarm input repeat the above steps or just copy the above settings to it 111 User Manual of DS 7600NI Series NVR Copy Alarm Input to 172 6 23 105 Figure 8 8 Copy Settings of Alarm Input 112 User Manual of DS 7600NI Series NVR 8 3 Detecting Video Loss Alarm Purpose Detect video loss of a channel and take alarm response action s Steps 1 Enter Video Loss interface of Camera Management and select a channel you want to detect Menu gt Camera gt Video Loss IP Camera 4 Figure 8 9 Video Loss Setup Interface 2 Set up handling method of video loss Check the checkbox of Enable Video Loss Alarm and click button to set up handling action of video loss 3 Set up arming schedule of the channel 1 Select Arming Schedule tab to set the channel s arming schedule 2 Choose one day of a week and up to eight time periods can be set within each day 3 Click Apply button to save the settings Note Time periods shall not be repeated or overlapped Settings Linkage Action Mon 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 lt 00 00 00 00 00 00 00 00 00 00 00 00 Figure 8 10 Set Arming Schedule of Video Loss 4 Select Linkage Action tab to set up alarm response action of video loss please refer to Chapter Setting 113 User Manual of DS 7600NI Series NVR Alarm Response Actions Repeat the above steps to set up arming sch
122. own Shutdown Cancel Figure 2 1 Shutdown Menu 2 Click the Shutdown button 3 Click the Yes button 4 Turn off the power switch on the rear panel when the attention pops up Please power off Figure 2 2 Shutdown Attention 24 User Manual of DS 7600NI Series NVR Rebooting the NVR In the Shutdown menu you can also reboot the NVR Steps 1 Enter the Shutdown menu by clicking Menu gt Shutdown 2 Click the Logout button to lock the NVR or the Reboot button to reboot the NVR 25 User Manual of DS 7600NI Series NVR 2 2 Using the Wizard for basic configuration By default the Setup Wizard starts once the NVR has loaded as shown in Figure below Wizard Start wizard when device starts Figure 2 3 Start Wizard Interface Operating the Setup Wizard 1 The Setup Wizard can walk you through some important settings of the NVR If you don t want to use the Setup Wizard at that moment click the Exit button You can also choose to use the Setup Wizard next time by leaving the Start wizard when the device starts checkbox checked 2 Click Next button on the Wizard window to enter the Login window as shown in Figure 2 4 Wizard Previous Figure 2 4 Login Window 3 Enter the admin password By default the password is 12345 4 To change the admin password check the New Admin Password checkbox Enter the new password and confirm the password in the given fields 5 Click the N
123. r Possible Reasons After connecting the IPC to the NVR the image is output via the main spot interface by default Steps 1 Enable the output channel 2 Select Menu gt Configuration gt Live View gt View and select video output interface in the drop down list and configure the window you want to view Notes 1 The view settings can only be configured by the local operation of NVR 2 Different camera orders and window division modes can be set for different output interfaces separately and digits like D1 and D2 stands for the channel number and X means the selected window has no image output 3 Check if the fault is solved by the above steps If it is solved finish the process If not please contact the engineer from Hikvision to do the further process Live view stuck when video output locally Possible Reasons a Poor network between NVR and IPC and there exists packet loss during the transmission b The motion detection and alarm functions are enabled and the parameters of Main Stream Normal and Main Stream Event are different So the image looks stuck due to the image changes between different resolutions c The frame rate has not reached the real time frame rate Steps 1 Verify the network between NVR and IPC is connected 1 When image is stuck connect the RS 232 ports on PC and the rear panel of NVR with the RS 232 cable 2 Open the Super Terminal and execute the comman
124. ra is disconnected you can click the icon to get the live view of click the icon to get the exception the camera information of camera Daemen 2 To add other IP cameras 1 Click the Custom Add button to pop up the Add IP Camera Custom interface Add IP Camera Custom IP Address Amount of Device M Protocol Managen 172 6 23 65 1 NC KDO32 HIKVISION 8000 172 6 23 65 HIKVISION 8000 admin Protocol Search Cancel Figure 2 14 Custom Adding IP Camera Interface 2 You can edit the IP address protocol management port and other information of the IP camera to 31 User Manual of DS 7600NI Series NVR be added 3 Click Add to add the camera OPTION 2 Steps 1 Enter the Camera Management interface Menu gt Camera gt Camera Menu S E Q E 5 Playback Manual Record n amp 3 Camera Configuration Maintenance Shutdown Camera OSD event PTZ settings etc Figure 2 15 Main Menu 2 Repeat the step 1 and 2 of adding IP cameras manually to add the camera Cam Add Sta IP Camera A Edit Camera Name Protocol Device Modie Manage D1 m 172 6 23 124 Camera 02 HIKVISION DS 2CD8153 8000 D2 m 172 6 23 177 IPCamera 02 HIKVISION 8000 D3 m 172 6 23 123 IPCamera 03 HIKVISION 8000 172 6 23 177 HIKVISION IPC 8000 R335 Df lt Net Receive Idle Bandwidth 17Mbps Refresh Delete All Add All Custom Add Figure 2 16 IP Camera Management Interface 3 For the
125. rch aeeie ices E a E E EN 78 6 1 4 Payne Back Dy TiSi aA 81 6 1 5 Playing Back by System LOSS usarien E meas E EEA 84 6 1 6 Playine Dack Pxtermal Filiee eiaaseaa derouneaecamead whyead ereeean 85 62 Auxiliary Functions Of Play Wack eins a A Stas lbonecleusions 87 6 2 1 Payne Back Frame Dy Frame en a abet ivelladebaiass 87 6 2 2 So ADT Ug of RC PR ee a me MCR ER TTT ae Ren Cen acl eer Tr ea mene eer he eee eet tae 87 6 2 3 DSA AO OU acca sisbenit ect gists aa a aaa nemeeans 90 6 2 4 Reverse PlaybacK of Multi Channel sirsiran EA NE 90 Chapter 7 Backpac AA E AAS 92 Tb Bac kne up Record FileSeonnera a T E TREE TTE ETA 93 7 1 1 OC EE DO aee E E E nee tare Ren enrrr re ters er 93 Telz Backing up by Normal Video Search nnn neeeesssseesooeeeersssssssssssseeeeerersssssssssseceereeeses 94 7 1 3 Backino up Dy Event Sea aen E a 99 7 1 4 Backing up Nide CIPS cireni a EE 101 Ta Mane me Backup Devices oieciaunat torre Mcamvatiatocnid aa ouedetnotnesetaued iakead 103 Chapter SAlarmi Sotnas or ves buesueseanasaussanssevacecesousstecaneneecs 107 Sak Setna Moon Detection Alae E a eecaeedensss 108 Sek Semne SS ANM sadan E E R e AR 110 So D tecune Video OSs Al atin ersrsonr en a a O dueeas enmeai eas obec 113 8 4 Detecting Video Tampering Alarm eriseeria aE EEA 115 So Handie Excepions Alaran e a eaten teins 117 S6 Setin Alarm Response ACHOS oiridrpririrni i e E E E E 118 8 7 Triggering or Clearing Alarm Output Manually cc cecccccsssecccc
126. rch button to get the search result information You may refer to the right side bar for the result 79 User Manual of DS 7600NI Series NVR gt Sour Start Time Play Sour Start Time 172 11 43 08 11 22 03 11 23 38 11 25 51 11 29 26 11 30 13 jf eee Sa ay 11 38 39 11 39 05 11 39 25 11 39 53 11 41 27 11 43 06 gt Pi Play C C C C O lt 4 Total 1 P 1 1 Total 414 P 1 4 Pre play 30s Pre play 30s Post play 30s Post play 30s 4 Back Back Figure 6 10 Search Result Bar Alarm In and Motion 5 Click button to play back the file Notes 1 Pre play and post play can be configured 2 If the event is set to trigger the recording of multiple channels clicking the will pop up the Synch Playback interface You can select the channels to play back synchronously You can click the Back button to back to the search interface 6 Playback interface The toolbar in the bottom part of Playback interface can be used to control playing process B Event Sour Start Time 14 07 56 14 13 08 14 22 22 14 22 53 14 24 40 14 25 37 14 25 58 14 31 58 14 32 47 14 33 31 14 35 15 14 37 03 gt Total 213 P 18 Pre play 30s Post play 30s A V 4e Back reeves Figure 6 11 Interface of Playback by Event 80 User Manual of DS 7600NI Series NVR Figure 6 12 Toolbar of Playback by Event Table 6 3 Detailed as En
127. rm Output Select an alarm output and set alarm name and dwell time Click Schedule button to set the arming schedule of alarm output Note If Manually Clear is selected in the dropdown list of Dwell Time you can clear it only by going to Menu gt Manual gt Alarm Alarm Status Alarm Input 172 6 23 105 8000 gt 1 5s i Figure 8 15 Alarm Output Setup Interface 118 User Manual of DS 7600NI Series NVR 2 Set up arming schedule of the alarm output Choose one day of a week and up to 8 time periods can be set within each day Note Time periods shall not be repeated or overlapped Handling lt Mon 00 00 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Cancel Figure 8 16 Set Arming Schedule of Alarm Output 3 Repeat the above steps to set up arming schedule of other days of a week You can also use Copy button to copy an arming schedule to other days Click the OK button to complete the video tampering settings of the alarm output No 4 You can also copy the above settings to another channel Copy Alarm Output to WAlarm Output No Alarm Name 17 gt G 23 1Ne RNND gt 1 M1 72 6 23 105 8000 gt 2 Figure 8 17 Copy Settings of Alarm Output 119 User Manual of DS 7600NI Series NVR 8 7 Triggering or Clearing Alarm Output Manually Purpose Sensor alarm can be triggered or cleared manually If Manually Clear is selected in the dropdow
128. rted by the device USB1 1 v Refresh 2 004MB New Folder Format Cancel Figure 7 2 Quick Export using USB1 1 93 User Manual of DS 7600NI Series NVR Export finished Stay in the Exporting interface until all record files are exported Figure 7 3 Export Finished 3 Check backup result Choose the record file in Export interface and click button to check it Note The Player player exe will be exported automatically during record file export Export Refresh Backup Export record files to me B Welcome to use backup E chO3 20110623000000 E ch03_20110623042932 E ch03_20110623091403 O h03 20110623092323 a ch03_20110623113325 E ch03_20110623132800 E ch03_20110623134743 B player exe Folder Folder OKB File OKB File 26 MB File 280MB File 4 423KB File 2 TMB File 110MB File 18 36 KB File 37 305K6B File 608KB File 06 23 2011 20 07 22 06 23 2011 20 07 28 06 23 2011 20 07 58 06 23 2011 20 07 36 06 23 2011 20 15 02 06 23 2011 20 11 14 06 23 2011 20 11 20 06 23 2011 20 12 54 06 23 2011 20 13 02 06 23 2011 20 13 12 06 23 2011 20 09 40 IDADOOi lt IDDIBDIP Ll 34 WN A A 44 79 AD OR we dees HH On MO rit lt nb wwe nbe ann v New Folder Format Cancel Figure 7 4 Checkup of Quick Export Result Using USB1 1 7 1 2 Backing up by Normal Video Search Purpose The record files can be backup to various devices such as USB devices USB flash dri
129. t export of device parameters Remote viewing of the device status system logs and alarm status Remote locking and unlocking of mouse Remote HDD initializing and program upgrading Remote system restart and shutdown User Manual of DS 7600NI Series NVR RS 485 transparent channel transmission Alarm and exception information can be sent to the remote host Remotely start stop recording Remotely start stop alarm output Remote PTZ control Two way audio and voice broadcasting Embedded WEB server Development Scalability SDK for Windows and Linux system Source code of application software for demo Development support and training for application system User Manual of DS 7600NI Series NVR TABLE OF CONTENTS Product Key Features sic cic acs ere ste cages AEEA adie aa A E 6 Chapter UNCrOGUC OM scssiccsscss ceccecacexscusaveceencasewesscen E E AEA S 13 kk Pront ego MR ener See tee ne eet Meee eee eee eee me RTT Ree nce ee ree erent meer Reena ret err ee 14 EZ SIR Remote Controls OperatOns tacit scnsesesteatanctiveannds S 15 LS OSB Mouse Opera i iadcccie defect A EA EE E E cles eucsicinan seni 18 ba hipi MetnoG Desc pHOm arti etalon cee dee areas acorn e vague 19 ES Rear Rane k aroari ance N see ss os ech N E E E E E E OTTE 20 Chapter 2Gettin e SUC scorende E N AESA AA AANE A 23 2 1 Starting Up and Shutting Down the NVR eeessssssssssseeenesssssssssssssseeerrsesssssssssssceerererssssssssssseeeer
130. tart recording or trigger full screen monitoring audio warning notify the surveillance center and so on In this chapter you can follow the steps to schedule a record which triggered by the detected motion Steps 1 Enter the Motion Detection interface Menu gt Camera gt Motion IP Camera 7 01 01 2010 Fri 1l 55 19 Full Screen Clear Figure 5 12 Motion Detection 2 Configure Motion Detection 1 Choose camera you want to configure 2 Check the checkbox after Enable Motion Detection 3 Drag and draw the area for motion detection by mouse If you want to set the motion detection for all the area shot by the camera click Full Screen To clear the motion detection area click Clear IP Camera 7 Full Screen Clear Figure 5 13 Motion Detection Mask 4 Click Setting and the message box for channel information pop up 62 User Manual of DS 7600NI Series NVR Settings Arming Schedule Linkage Action WIP Camera D1 H8D3 WDd4 Figure 5 14 Motion Detection Setting 5 Select the channels which you want the motion detection event to trigger recording 6 Click Apply to save the settings 7 Click OK to back to the upper level menu 8 Exit the Motion Detection menu 3 Edit the Motion Detection Record Schedule For the detailed information of schedule configuration see Chapter Configuring Record Schedule 63 User Manual of DS 7600NI Series NVR 5 4 Configuring Alarm Triggered Record Purpos
131. teps 1 Click the Bad Sector Detection tab 151 User Manual of DS 7600NI Series NVR 2 Select the HDD No in the dropdown list you want to configure and choose All Detection or Key Area Detection as the detection type 3 Click the Detect button to start the detection S M A R T Settings 931 51GB 232MB Testing 39 0 Cancel Normal Damaged Shield Figure 10 21 Bad Sector Detection And you can click Error info button to see the detailed damage information And you can also pause resume or cancel the detection 152 User Manual of DS 7600NI Series NVR 10 7 Configuring HDD Error Alarms Purpose You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal Steps 1 Enter the Exception interface Menu gt Configuration gt Exceptions 2 Select the Exception Type to HDD Error from the dropdown list 3 Click the checkbox s below to select the HDD error alarm type s as shown in Figure 10 22 Note The alarm type can be selected to Audio Warning Notify Surveillance Center Send Email and Trigger Alarm Output Please refer to Chapter Setting Alarm Response Actions Exception Type HDD Error Audible Warning Notify Surveillance Center Trigger Alarm Output WAlarm Output No Alarm Name 172 6 23 126 8000 gt 1 Figure 10 22 Configure HDD Error Alarm 4 When the Trigger Alarm Output is selected you can also select the alarm output to be triggered from the list
132. terface 3 Configure the following settings Language The default language used is English Resolution Select the output resolution which must be the same with the resolution of the monitor screen Time Zone Select the time zone Date Format Select the date format System Date Select the system date System Time Select the system time Mouse Pointer Speed Set the speed of mouse pointer 4 levels are configurable Enable Wizard Enable disable the Wizard when the device starts up Enable Password Enable disable the use of the login password 4 Click the Apply button to save the settings 170 User Manual of DS 7600NI Series NVR 13 2 Configuring DST Settings Steps 1 Enter the General Settings interface Menu gt Configuration gt General 2 Choose DST Settings tab General More Settings B Auto OST Adjustment Enable DS From Apt Oct 60 Minules Figure 13 2 DST Settings Interface You can check the checkbox before the Auto DST Adjustment item Or you can manually check the Enable DST checkbox and then you choose the date of the DST period 171 User Manual of DS 7600NI Series NVR 13 3 Configuring More Settings for Device Parameters Steps 1 Enter the General Settings interface Menu gt Configuration gt General 2 Click the More Settings tab to enter the More Settings interface as shown in Figure 13 3 General DST Settings Device Name Embedded Net DVR Device No 255 Auto Logo
133. tibility from vendor 105 User Manual of DS 7600NI Series NVR USB CD DYD RW v Refresh Figure 7 31 USB Writer Management 106 User Manual of DS 7600NI Series NVR Chapter 8 Alarm Settings 107 User Manual of DS 7600NI Series NVR 8 1 Setting Motion Detection Alarm Steps 1 Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion detection Menu gt Camera gt Motion IP Camera 4 01 01 2010 Fri 11 55 19 Full Screen Clear Figure 8 1 Motion Detection Setup Interface 2 Set up detection area and sensitivity Tick Enable Motion Detection use the mouse to draw detection area s and drag the sensitivity bar to set sensitivity Click button and set alarm response actions 3 Click Trigger Channel tab and select one or more channels which will start to record or become full screen monitoring when motion alarm is triggered and click Apply to save the settings Settings Arming Schedule Linkage Action WIP Camera Di DEERE Dr Figure 8 2 Set Trigger Camera of Motion Detection 4 Set up arming schedule of the channel 1 Select Arming Schedule tab to set the arming schedule of handling actions for the motion detection 2 Choose one day of a week and up to eight time periods can be set within each day 3 Click Apply to save the settings Note Time periods shall not be repeated or overlapped 108 User Manual of DS 7600NI Series NVR
134. to the full screen in the NVR local menu Please refer to chapter 5 3 for details Steps 1 Enter the Playback interface and play a record file Refer to Chapter 6 1 1 for the detailed information about searching and playback of the record files 87 User Manual of DS 7600NI Series NVR Normal Camera iPCamera 01 iPCamera 02 iPCamera 03 M Camera01 iPCamera 05 MiPCamera 06 MIPCamera 08 iPCamera 09 iPCamera 10 iPCamera 11 WiPCamera 12 iPCamera 13 04 25 2013 10 00 12 04 25 2013 16 02 59 2B Figure 6 22 Interface of Playback by Time 2 Click the on the playback control toolbar to enter Smart Search mode 3 Click and drag the mouse to draw area s You can click button coe to set the full screen as target searching area After drawing area s click button b to execute smart search in this area Note Multi area and full screen searching modes are supported fith Figure 6 23 Draw Area of Smart Search The results of smart search will be marked as in the progress bar The hidden list of record files display when moving the mouse to the right of the playback interface 88 User Manual of DS 7600NI Series NVR Camera iPCamera 01 iPCamera 02 iPCamera 03 Camera01 iPCamera 05 MiPCamera 06 vic iPCamera 08 iPCamera 09 iPCamera 10 iPCamera 11 iPCamera 12 iPCamera 13 04 25 2013 10 00 12 04 25 2013 16 26 59 Figure 6 25 Toolbar of Smart
135. toring When an alarm is triggered the local monitor VGA or HDMI monitor display in full screen the video image from the alarming channel configured for full screen monitoring If alarms are triggered simultaneously in several channels their full screen images will be switched at an interval of 10 seconds default dwell time A different dwell time can be set by going to Menu gt Configuration gt Live View and set the value of Full Screen Monitoring Dwell Time Auto switch will terminate once the alarm stops and you will be taken back to the Live View interface Note You must select during Trigger Channel settings the channel s you want to make full screen monitoring Audible Warning Trigger an audible beep when an alarm is detected Notify Surveillance Center Sends an exception or alarm signal to remote alarm host when an event occurs The alarm host refers to the PC installed with Remote Client Note The alarm signal will be transmitted automatically at detection mode when remote alarm host is configured Please refer to Chapter Configuring Remote Alarm Host for details of alarm host configuration Email Linkage Send an email with alarm information to a user or users when an alarm is detected Please refer to Chapter 9 2 10 Configuring Email for details of Email configuration Trigger Alarm Output Trigger an alarm output when an alarm is triggered 1 Enter Alarm Output interface Menu gt Configuration gt Alarm gt Ala
136. tus of PPPoE connection Please refer to Chapter Viewing System Information for PPPoE status 9 2 2 Configuring DDNS Purpose If your NVR is set to use PPPoE as its default network connection you may set Dynamic DNS DDNS to be used for network access Prior registration with your ISP is required before configuring the system to use DDNS Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the DDNS tab to enter the DDNS Settings interface as shown in Figure 9 3 123 User Manual of DS 7600NI Series NVR Figure 9 3 DDNS Settings Interface 3 Check the DDNS checkbox to enable this feature 4 Select DDNS Type Five different DDNS types are selectable IPServer DynDNS PeanutHull NO IP and HiDDNS e IPServer Enter Server Address for PServer Figure 9 4 PServer Settings Interface DynDNS 1 Enter Server Address for DynDNS i e members dyndns org 2 In the NVR Domain Name text field enter the domain obtained from the DynDNS website 3 Enter the User Name and Password registered in the DynDNS website v DynDNS Figure 9 5 DynDNS Settings Interface e PeanutHull Enter the User Name and Password obtained from the PeanutHull website PeanutHull Figure 9 6 PeanutHull Settings Interface e NO IP Enter the account information in the corresponding fields Refer to the DynDNS settings 1 Enter Server Address for NO IP 124 User Manual of DS 7600N
137. urpose The device provides the HDD detection function such as the adopting of the S M A R T and the Bad Sector Detection technique The S M A R T Self Monitoring Analysis and Reporting Technology is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures S M A R T Settings Steps 1 Enter the S M A R T Settings interface Menu gt HDD gt HDD Detect 2 Select the HDD to view its S M A R T information list as shown in Figure 10 20 Bad Sector Detection Continue to use this disk when sel evaluaton 1s failed HDD 2 Self test Status Self test successful Self test Type Short Test SMART it lemperature C 36 Power On days a79 Self evaluation Pass Al evaluation Functional SMA RET Information opin Up Time IK i 0 otanfStop Count ARK 5 99 1690 Reallocated Sector Co OK 33 0 seek Error Rate OK 932 70223201 Power on Hours Count p ou fb 21114 Spin Up Retry Count 0 Apply Figure 10 20 S M A R T Settings Interface The related information of the S M A R T is shown on the interface You can choose the self test types as Short Test Expanded Test or the Conveyance Test Click the start button to start the S M A R T HDD self evaluation Note If you want to use the HDD even when the S M A R T checking is failed you can check the checkbox of the Continue to use the disk when self evaluation is failed item Bad Sector Detection S
138. ut Never Menu Output Mode HDMI GA Figure 13 3 More Settings Interface 3 Configure the following settings e Device Name Edit the name of NVR e Device No Edit the serial number of NVR The Device No can be set in the range of 1 255 and the default No is 255 The number is used for the remote and keyboard control e Auto Logout Set timeout time for menu inactivity E g when the timeout time is set to 5 Minutes then the system will exit from the current operation menu to live view screen after 5 minutes of menu inactivity Menu Output Mode You can choose the menu display on different video output 4 Click the Apply button to save the settings 172 User Manual of DS 7600NI Series NVR 13 4 Managing User Accounts Purpose There is a default account in the NVR Administrator The Administrator user name is admin and the password is 12345 The Administrator has the permission to add and delete user and configure user parameters 13 4 1 Adding a User Steps 1 Enter the User Management interface Menu gt Configuration gt User Figure 13 4 User Management Interface 2 Click the Add button to enter the Add User interface 173 User Manual of DS 7600NI Series NVR Add User 01 settee stete Operator 00 00 00 00 00 Cancel Figure 13 5 Add User Menu 3 Enter the information for new user including User Name Password Level and User s MAC Address Level Set the user level to
139. ves USB HDDs USB writer and SATA writer Backup using USB flash drives and USB HDDs Steps 1 Enter Export interface Menu gt Export gt Normal 2 Set search condition and click Search button to enter the search result interface 94 User Manual of DS 7600NI Series NVR MIP Camera MDi1 W D2 WdD3 Wd4 07 05 2013 16 48 08 08 05 2013 00 48 18 All All 07 05 2013 00 00 00 0 7 05 2013 23 59 59 Figure 7 5 Normal Video Search for Backup 3 Select record files you want to back up Click to play the record file if you want to check it Check the checkbox before the record files you want to back up Note The size of the currently selected files is displayed in the lower left corner of the window Search result 10 20 2011 11 50 24 15 23 54 1 038 237KB 10 20 2011 15 23 54 16 11 53 399 657KB 10 20 2011 10 33 53 11 17 18 692 336KB 10 20 2011 11 1 18 11 18 52 25 163KB 10 20 2011 13 13 10 14 16 30 1 013 691KB 10 20 2011 14 16 30 15 21 25 1 038 801KB 2 10 20 2011 15 21 25 16 11 23 722 552KB pp a i amp BEESSEEEaEES 10 20 2011 10 33 51 11 18 56 668 672KB ED HDD 5 Start time 10 20 2011 09 08 52 End time 10 20 2011 11 50 24 Total size 6 482MB Cancel Figure 7 6 Result of Normal Video Search for Backup 4 Export Click Export button and start backup Note If the inserted USB device is not recognized e Click the Refresh button e Reconn
140. vice Information menu to view the device name model serial No firmware version and encode version as shown in Figure 12 1 Embedded Net DVR XXXXXXXXXXXXXXXXXXXX Vx x x Build xxxxxx Vx x Build xxxxxx Figure 12 1 Device Information Interface 12 1 2 Viewing Camera Information Steps 1 Enter the System Information interface Menu gt Maintenance gt System Info 2 Click the Camera tab to enter the Camera Information menu to view the status of each camera as shown in Figure 12 2 Camer Camera Name Status Motion Det Video Tamp Video Loss D1 IPCamera 08 Connected Used Not used Not used D2 IPCamera01 Connected Used Used Not used Figure 12 2 Camera Information Interface 12 1 3 Viewing Record Information Steps 1 Enter the System Information interface Menu gt Maintenance gt System Info 2 Click the Record tab to enter the Record Information menu to view the recording status recording parameters of each camera as shown in Figure 12 3 Recor Stream Frame Bitrate Kbps Resolution Recor Encodi Redun Used Video 25fps 2048 704 576 4 Contin Event No Used Video 25fps 2048 704 576 4 Contin Contin No Figure 12 3 Record Information Interface 159 User Manual of DS 7600NI Series NVR 12 1 4 Viewing Alarm Information Steps 1 Enter the System Information interface Menu gt Maintenance gt System Info 2 Click the Alarm tab to enter the Alar
141. work Settings menu Click Apply button to save the settings Select the Email tab to enter the Email Settings interface xxx Ssmip com 25 E name1 name 1 x com Receiver 1 name2 name2 xx com 2S Figure 9 20 Email Settings Interface Configure the following Email settings Enable Server Authentication optional Check the checkbox to enable the server authentication feature User Name The user account of sender s Email for SMTP server authentication Password The password of sender s Email for SMTP server authentication SMTP Server The SMTP Server IP address or host name e g smtp 263xmail com SMTP Port No The SMTP port The default TCP IP port used for SMTP is 25 Enable SSL optional Click the checkbox to enable SSL if required by the SMTP server Sender The name of sender Sender s Address The Email address of sender Select Receivers Select the receiver Up to 3 receivers can be configured 131 User Manual of DS 7600NI Series NVR Receiver The name of user to be notified Receiver s Address The Email address of user to be notified Enable Attached Pictures Check the checkbox of Enable Attached Picture if you want to send email with attached alarm images The interval is the time of two adjacent alarm images You can also set SMTP port and enable SSL here Interval The interval refers to the time between two actions of sending attached pictures E mail Test Sends a test message to ver
142. y ONVIF is supported x x 192 User Manual of DS 7600NI Series NVR IPC Manufacturer or Max Model Version Sub stream Audio Protocol Resolution SNC RH124 ONVIF 1280x720 v v compatibility SONY SNC EP580 ONVIF 1920x1080 v v compatibility SNC DH220T Only 2048x1536 x x ONVIF is supported IP8331 ONVIF 640x480 compatibility IP8332 ONVIF 1280x800 compatibility FD8134 ONVIF 1280x800 x x compatibility IP8161 ONVIF 1600x1200 x J Vivotek compatibility F3110 M2 1 6 01 1280x720 F3206 MG 1 6 02c045 1920x1080 193 First Choice for Security Professionals HANGZHOU HIKVISION DIGITAL TECHNOLOGY CO LTD www hikvision com
143. ystems to control streaming media servers Steps 1 Enter the Network Settings menu Menu gt Configuration gt Network 2 Select the More Settings tab to enter the More Settings menu as shown in Figure 9 14 129 User Manual of DS 7600NI Series NVR Figure 9 17 RTSP Settings Interface 3 Enter the RTSP port in the text field of RTSP Service Port The default RTSP port is 554 and you can change it according to different requirements 4 Click Apply button to save and exit the menu 9 2 8 Configuring Server and HTTP Ports Purpose You can change the server and HTTP ports in the Network Settings menu The default server port is 8000 and the default HTTP port is 80 Steps 1 Enter the Network Settings interface Menu gt Configuration gt Network 2 Select the More Settings tab to enter the More Settings interface as shown in Figure 9 14 3 Enter new Server Port and HTTP Port Server Port HTTP Port Multicast IP Figure 9 18 Host Others Settings Menu 4 Enter the Server Port and HTTP Port in the text fields The default Server Port is 8000 and the HTTP Port is 80 and you can change them according to different requirements 5 Click Apply button to save and exit the interface Note The Server Port should be set to the range of 2000 65535 and it is used for remote client software access The HTTP port is used for remote IE access 9 2 9 Configuring HTTPS Port Purpose HTTPS provides authentication of the we

Download Pdf Manuals

Related Search

Related Contents

JBL GTO6426 Coaxial Car Speaker  Tradewinds HD-P63F3ET-H Instructions / Assembly  the complete Installation and tuning manual  Massive PIR detector 87098/12/30  LimpezA e CONservAçãO  1-155-606 遺伝子組換え原理探究キット FSB14（取扱説明書）  Manuale dell`operatore Telecomando esterno (ERC  

Copyright © All rights reserved. Failed to retrieve file