Hikvision Digital Technology DS-2CD4032FWD-A surveillance camera
Contents
1. Network Box Camera Quick Operation Guide Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied C accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU Network Box Camera Quick Operation Guide 2012 19 EU WEEE directive Products marked with this symbol cannot be d2. Table of Contents 1 Appearance Description cccsessssseeeseeeceeeeeesseeeseeeeeeeessneeeneeee 8 PA L e a OPEP SIAE S IEAS TA EAE IO AA TAT A 12 2 1 Ceiling MOUNTING aae 13 2 2 Wall Mounting 2 3 Installing the SD Card 3 Setting the Network Camera over the LAN ssssssssscsseeseeeenee 20 4 Accessing via Web Browser sssssscsssssecsesesescssseseeenseseeseeseeeeees 25 Network Box Camera Quick Operation Guide 1 Appearance Description The overview of the box camera is shown below Figure 1 1 Overview 1 The overview of the components and the interface are shown below Figure 1 2 Overview 2 Network Box Camera Quick Operation Guide The interfaces on the rear panel are shown below 8 9 10 IV reler ro t EA T DEO OUT A 11 ABF AC 24V 48919 Gs ol DC12V z H P Ed El mejta 18 0000 18 17 16 13 14 12 Figure 1 3 Overview 3 Table 1 1 Description No Description No Description Lens Mount 2 MIC 20 UNC Screw Hole Power Indicator Network Box Camera Quick Operation Guide No Description No Description 5 Auto iris Interface 6 LAN PoE 7 Power Outlet 8 Reset 9 Micro SD Card Slot 10 Video
3. You may have to close the web browser to finish the installation of the plug in 26 Network Box Camera Quick Operation Guide Live View Playback Log Configuration e click here to download and install the plug in Close the browser when installing the plug in Figure 4 2 Download Plug in Setup Web Components Click Next to continue or Cancel to exit Setup Figure 4 3 Install Plug in 1 27 Network Box Camera Quick Operation Guide Setup Web Components elle lis Setup has finished installing Web Components on your computer Click Finish to exit Setup Figure 4 4 Install Plug in 2 6 Reopen the web browser after the installation of the plug in and repeat steps 2 4 to login For detailed instructions of further configuration please refer to the user manual of network camera 28
4. cable to the auto iris interface Figure 2 2 Install the Lens 4 Align the screw hole on the camera with the ceiling mount and rotate the camera to get it fixed 14 Network Box Camera Quick Operation Guide 5 Adjust the surveillance angle 1 Loosen the pan nut to adjust the pan angle 0 360 2 Loosen the knob on the ceiling mount to adjust the tilt angle 0 90 6 Adjust the Lens 1 Connect the VIDEO OUT interface of the camera to the debugging monitor 2 Adjust the Zoom Lever and Focus Level to obtain a perfect image on the monitor Knob Figure 2 3 Install the Camera to the Mount and Adjust the Angle 15 Network Box Camera Quick Operation Guide 2 2 Wall Mounting Steps 1 Install the lens not supplied to the camera and rotate it to get it tightened 2 Plug the auto iris cable to the auto iris interface Figure 2 4 Install the Lens 3 Loosen the lock screw on the mount and remove the tilt adjust table from the wall mount 16 Network Box Camera Quick Operation Guide Figure 2 5 Remove the Tilt Adjust Table 4 Fit the removed tilt adjust table to the camera and fix it with two screws Figure 2 6 Install the Tilt Adjust Table 5 Secure the wall mount to the wall with the supplied expansion screws 17 Network Box Camera Quick Operation Guide Figure 2 7 Install the Wall Mount 6 Install the camera to the wal
5. HIKVISION Network Box Camera Quick Operation Guide UD 6L0201B1320A01 www hikvision com Network Box Camera Quick Operation Guide Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer About This Document This manual applies to the following camera models Model DS 2CD4012F A P W SDI FC DS 2CD4012FWD A P W SD1 FC DS 2CD4024F A P W SDI FC DS 2CD4026FWD A P W DS 2CD4032FWD A P W SDI FC DS 2CD6026FHWD A iDS 2CD6024FWD A B iDS 2CD6024FWD A F This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual DISCLAIMER STATEMENT Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested for fire shock or casualty hazards as outlined in UL s Standard s for Safety UL60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT 0501001031227
6. N and list the device information like IP address subnet mask port number device serial number device version etc shown in Figure 3 2 20 Network Box Camera Quick Operation Guide O Use PCNVR software and to list the online devices Please refer to the user manual of PCNVR client software for detailed information 2 Change the IP address and subnet mask to the same subnet as of your PC Refer to the following introductions to set IP address with SADP software O Search active devices online Search online devices automatically After launch the SADP software it automatically searches the online devices every 15 seconds from the subnet where your computer locates It displays the total number and information of the searched devices in the Online Devices interface Device information including the device type IP address port number gateway etc will be displayed 21 Network Box Camera Quick Operation Guide 2 Tota mahar of sion dione T Orma se Natnere Parameters O Devce Tipe PaAdess Pot Setar larson IPGalenay Sano wasaress on oswowa iszeess sooo VOLDuIMOUO 1920 01 3000040000000004 ap ott Enter De saman pastor tine eoe betore oo sore Pa nenons parametere Mana Sena codo ie a sees oe charactors camoeed iy Pe stat hme ana he seat honom atthe dear Figure 3 2 Search Online Devices Device can be searched and displayed in the list in 15 seconds after it goes online it will be removed from the list i
7. Out 11 Grounding 12 Alarm Out 13 RS 232 14 RS 485 15 Alarm In 16 Audio Out 17 ABF 18 Audio In oa Only the models with A in its suffix support ABF function To reset the camera default parameters you need to press and hold the RESET button and power on the camera After the power on of the camera you must still press and hold the Reset button for about 20 seconds The type of auto iris interface is shown as below figure 3 4 Figure 1 4 Auto iris Interface 10 Network Box Camera Quick Operation Guide Table 1 2 Pins No DC driven 1 Damp 2 Damp 3 Drive 4 Drive Power Video and GND pins are used when the auto iris is driven by video Damp Damp Drive and Drive pins are used when the auto iris is driven by DC 11 Network Box Camera Quick Operation Guide 2 Installation Before you start Make sure the device in the package is in good condition and all the assembly parts are included Make sure all the related equipment is power off during the installation Check the specification of the products for the installation environment Make sure the power supply is matched with your required voltage to avoid damage If the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself Make sure that the wall is stron
8. g enough to withstand three times the weight of the camera foan NOTE For the camera that supports IR you are required to pay attention to the following precautions to prevent IR reflection e Dust or grease on the dome cover will cause IR reflection Please do not remove the dome cover film until the installation is finished If there is dust or grease on the dome cover clean the dome cover with clean soft cloth and isopropyl alcohol 12 Network Box Camera Quick Operation Guide e Make sure that there is no reflective surface too close to the camera lens The IR light from the camera may reflect back into the lens causing reflection e The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly 2 1 Ceiling Mounting Steps 1 Install the ceiling mount to the ceiling with the supplied expansion screws Adjustable Nut Figure 2 1 Install the Mount 13 Network Box Camera Quick Operation Guide 2 Fit the lens not supplied to the camera and rotate it to get it tightened fia hore e Install the adapter ring to the lens interface if a C mount lens is used e Amanual iris lens can be directly installed to the camera without plugging the power cable of the auto iris to the auto iris interface 3 Plug the auto iris
9. ions of the nation and region Please refer to technical specifications for detailed information e Input voltage should meet both the SELV Safety Extra Low Voltage and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950 1 standard Please refer to technical specifications for detailed information Network Box Camera Quick Operation Guide e Do not connect several devices to one power adapter as adapter overload may cause over heating or a fire hazard e Please make sure that the plug is firmly connected to the power socket When the product is mounted on wall or ceiling the device shall be firmly fixed e f smoke odor or noise rise from the device turn off the power at once and unplug the power cable and then please contact the service center A Cautions e Make sure the power supply voltage is correct before using the camera e Do not drop the camera or subject it to physical shock e Do not touch sensor modules with fingers If cleaning is necessary use clean cloth with a bit of ethanol and wipe it gently If the camera will not be used for an extended period please replace the lens cap to protect the sensor from dirt e Do not aim the camera at the sun or extra bright places Blooming or smearing may occur otherwise which is not a malfunction and affect the endurance of sensor at the same time e The sensor may be burned out by a laser beam so when any laser equipment is in using make sure
10. isposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier E upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info Network Box Camera Quick Operation Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Serious injury or death may occur if any of the warnings are neglected Cautions Injury or equipment damage may occur if any of the cautions are neglected A Warnings Follow these Cautions Follow these safeguards to prevent precautions to prevent serious injury or death potential injury or material damage A Warnings e Inthe use of the product you must be in strict compliance with the electrical safety regulat
11. l mount and tighten the two lock screws 7 Adjust the surveillance angle 1 Loosen the pan nut to adjust the pan angle 0 360 2 Loosen the knob on the ceiling mount to adjust the tilt angle 0 45 8 Adjust the Lens 1 Connect the VIDEO OUT interface of the camera to the debugging monitor 2 Adjust the focus level to obtain a perfect image on the monitor 18 Network Box Camera Quick Operation Guide Pan Adjust Screw Figure 2 8 Adjust the Surveillance Angle 2 3 Installing the SD Card Insert the SD card to the SD card slot to get it installed Push the inserted SD card slightly to get it sprung by its built in springing to remove it AN AA Micro SD Card Figure 2 9 Install the SD Card 19 Network Box Camera Quick Operation Guide 3 Setting the Network Camera over the LAN Purpose To view and configure the camera via LAN Local Area Network you need to connect the network camera in the same subnet with your PC Then install the SADP or PCNVR software to search and change the IP of network camera The following figure shows the cable connection of network camera and PC Network Camera Computer Figure 3 1 Wiring over LAN Set the IP address of the camera for accessing via LAN Steps 1 To get the IP address you can choose either of the following methods O Use SADP a software tool which can automatically detect network camera in the LA
12. n 45 seconds after it goes offline Search online devices manually You can also click ie Rokesh to refresh the online device list manually The newly searched devices will be added to the list 22 Network Box Camera Quick Operation Guide You can click or on each column heading to order the information you can click to show the device table and hide the network parameter panel on the right side or click ss to show the network parameter panel O Modify device information Steps 1 Select the device to be modified in the device list as shown in Figure 3 3 The network parameters of the device will be displayed in the Modify Network Parameters panel on the right side as shown in Figure 3 4 2 Edit the modifiable network parameters e g IP address and port number 3 Enter the password of the admin account of the device in the Password field and click Save to save the changes Total munber of online devices 1 Retesh D DevceType IPv4Address Pon Software Version IPv4 Gateway Serial No 001 DSXXXX XX 192 0 0 64 8000 VX X Xbuild XXXX 192 0 0 1 2 00 0000 Figure 3 3 Select a Device 23 3 NOTE Network Box Camera Quick Operation Guide Modify Network Parameters IP Address 192 0 0 64 Port 8000 Subnet Mask 255 255 0 0 IPv4 Gateway 192 0 0 1 IPv6 Address IPv6 Gateway IPv6 Prefix Length Serial No KXXXXXXXXXXXXXXXXXXXX Save 9 Note Enter the admin passw
13. ord of the device before you save the network parameters Figure 3 4 Modify Network Parameters Enter the IP address of network camera in the address field of the web browser to view the live video The default value of the IP address is 192 0 0 64 The default user name is admin and password is 12345 For accessing the network camera from different subnets please set the gateway for the network camera after you log in 24 Network Box Camera Quick Operation Guide 4 Accessing via Web Browser System Requirement Operating System Microsoft Windows XP SP1 and above version Vista Win7 Server 2003 Server 2008 32bits CPU Intel Pentium IV 3 0 GHz or higher RAM 1G or higher Display 1024x768 resolution or higher Web Browser Internet Explorer 6 0 and above version Apple Safari 5 02 and above version Mozilla Firefox 3 5 and above version and Google Chrome8 and above version Steps 1 Open the web browser 2 Inthe browser address bar input the IP address of the network camera e g 192 0 0 64 and press the Enter key to enter the login interface 3 Input the user name and password 4 Click Login 25 Network Box Camera Quick Operation Guide English x User Name admin Password eseese Login Figure 4 1 Login Interface 5 Install the plug in before viewing the live video and managing the camera Please follow the installation prompts to install the plug in
14. that the surface of sensor will not be exposed to the laser beam Network Box Camera Quick Operation Guide Do not place the camera in extremely hot cold the operating temperature shall be 30 C 60 C or 40 C 60 C if the camera model has an H in its suffix dusty or damp locations and do not expose it to high electromagnetic radiation To avoid heat accumulation good ventilation is required for operating environment Keep the camera away from liquid while in use While in delivery the camera shall be packed in its original packing or packing of the same texture Regular part replacement a few parts e g electrolytic capacitor of the equipment shall be replaced regularly according to their average enduring time The average time varies because of differences between operating environment and using history so regular checking is recommended for all the users Please contact with your dealer for more details Improper use or replacement of the battery may result in hazard of explosion Replace with the same or equivalent type only Dispose of used batteries according to the instructions provided by the battery manufacturer If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the camera yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance Network Box Camera Quick Operation Guide
Download Pdf Manuals
Related Search