Acroprint 125NR4
Contents
1. ECROPRINT Time for Business To Remove Case Cover 1 Turn key one quarter turn clockwise 2 Lift case cover up then forward 3 Reverse procedure to replace cover To Set Time and or Date NOTE Unless your recorder is equipped with continental 0 23 hours all PM hours on the time card will be printed underscored Ex 1 00 To change the time and or date follow these steps 1 Unplug recorder and remove Case Cover 2 To Set Day Date A Make sure current time setting is between midnight and noon see note above B Push down and release Yellow Lever see Figure 1 to set correct day date C Plug in recorder and punch card to verify correct setting Repeat steps A C if reading is incorrect 3 To Set Time A Push down and release Black Minute Lever to set the correct time see Figure 1 If minute lever does not work plug in recorder and wait for minute hand to advance then unplug recorder and try lever again DO NOT MOVE CLOCK HANDS TO SET THE TIME 4 To Set Month if so equipped A Turn Month Knob see Figure 1 counter clockwise to select correct month B Plug in recorder and punch card to verify correct setting Repeat steps A B if reading is incorrect 5 To Set Year if so equipped A Insert point of pen into spoke on side of year wheel and rotate counter clockwise B Plug in recorder and punch card to verify correct setting Repeat steps A B if reading is incorrect Figure 1 cover re2. equipped with a continental hour tenths or hundredths wheel please see the minute conversion chart below z DECIMAL EQUIVALENTS OF MINUTE TYPE WHEELS Z Minutes Tenths Hundredths Minutes Tenths Hundredths x oo q 0 30 50 gt E 1 31 52 i 6 2 32 54 3 33 55 MIDNIGHT A A Be 5 35 58 o i 6 36 60 2 2 7 37 62 3 3 8 38 64 4 4 9 39 65 5 5 10 40 66 AM 6 6 11 41 68 7 7 12 42 70 8 8 13 43 72 9 9 14 44 7 74 10 10 15 45 7 75 11 11 16 46 7 76 NOON 17 47 T 78 18 48 8 80 12 12 19 49 8 82 1 13 20 50 8 84 2 14 21 51 8 85 3 15 22 52 8 86 4 16 23 53 8 88 pm 2 1 24 54 9 90 6 18 25 55 9 92 f 19 26 56 9 94 27 57 9 95 fo 22 28 58 9 96 11 23 Declaration Of Conformity According To EMC Directive 73 23 EEC We declare under our sole responsibility that the magnetic stripe and or bar code reading and or data recording equipment Model 125 150 P150 Recorders to which this declaration relates are in conformity with the following standards EN 60950 1 1992 I the undersigned hereby declare that the equipment specified above conforms to the above directive and standards Raleigh North Carolina USA bd LA December 6 2001 W Glenn Robbins All Rights Reserved COPYRIGHT 1996 Part No 06 0104 000 Rev Q Acroprint Time Recorder Company f
3. es to the company from which the unit was purchased Site Requirements The recorder should be mounted on a sturdy wall shelf or other support area Do not use the recorder under the following conditions e extremely high or low temperature operating range 0 to 50 C 32 to 122 F e extremely high or low humidity operating range 0 to 90 RH non condensing e areas of high dust concentration e areas with extreme vibration or when placed on an unstable or unlevel surface Mounting the Recorder and Card Racks The recorder requires an uninterrupted AC power supply and should be mounted within 6 feet of a power receptacle to accommodate the unit s power cord The suggested wall mounting layout for the recorder and optional card racks is shown in Figure 4 Suggestions for mounting on specific wall and shelf surfaces follow Figure 4 suggested mounting layout 45 32 5 40 e RECEPTACLE NYY Y Wooden Plywood Walls You may use the three screws included with the recorder to mount the recorder Install a screw in the wall 53 above the floor Leave enough of the screw protruding so the recorder will hang flat against the wall through the keyhole on back of the clock Hang and level the recorder Insert and tighten screws through the lower left and right mounting holes Masonry Walls You may use plastic masonry anchors and screws available at your
4. local hardware store to mount the recorder Mark a location on the wall 53 above the floor Drill a hole with a 1 4 masonry bit and insert a plastic anchor Tighten a screw at this location leaving enough of the screw protruding so the recorder will hang flat against the wall through the keyhole on back of the clock Hang and level the recorder Mark the location of the lower left and right mounting holes Remove the recorder drill holes and insert anchors Replace the recorder insert and tighten screws through the lower left and right mounting holes and fully tighten the keyhole screw Sheetrock Hollow Core Walls You may use molly fasteners available at your local hardware store to mount the recorder Follow the procedure for masonry walls using the molly fasteners instead Alternatively you may use longer wood screws to attach the recorder to a stud behind the sheetrock using the keyhole and the lower center mounting hole on the recorder NOTE Always consult with a professional contractor carpenter and obey all local building and fire codes when installing your recorder Maintenance To obtain the best results from your recorder we recommend periodic inspection cleaning and oiling throughout each year by an authorized dealer For further information contact your dealer or Acroprint Time Recorder Co 5640 Departure Dr Raleigh NC 27616 U S A IN USA 800 334 7190 Conversion Chart If your recorder is
5. moved dial Black Minute Lever Yellow Day Date Lever Month Knob turn counter clockwise Note Day Date amp Month levers are shown in cut away views The levers are behind the clock General Service Instructions Models 125 and 150 Recorders IMPORTANT NOTES 1 The date setting if so equipped MUST be manually reset to the first of the month each month following any month with less than 31 days 2 The month and year settings if so equipped MUST be manually reset every month year 3 To reset your recorder after a power failure follow the steps 1 5 4 HINT If clock is set slightly ahead of actual time you may unplug it until it matches the correct time To Set Time and or Date for Left Print Models 1 Unplug recorder and remove Case Cover 2 To Set Day Date A Follow the same steps as for standard models but note the different location of Yellow Day Date lever in Figure 2 3 To Set Time A Follow the same steps as for standard models 4 To Set Month if so equipped A Move Month Lever see Figure 2 to extreme left position then return slowly to right until an audible click is heard B Plug in recorder and punch card to verify correct setting Repeat steps A B if reading is incorrect 5 To Set Year if so equipped A Note that year set lever is located at the rear of the typehead assembly Follow the same s
6. teps as for setting the month on left print models Figure 2 left print models Month Lever Black Minute Lever Yellow Day Date Lever To Change Ribbon A replacement Acroprint Ribbon is supplied on two spools When ordering specify 20 106 002 for two color right margin print recorder 20 106 000 for two color left margin print recorder or 20 0106 003 for solid blue ribbon To replace the ribbon perform the following steps 1 Note how ribbon is threaded Pull right Ribbon Tension Spring see Figure 3 forward and remove spool Pull left Ribbon Tension Spring see Figure 3 forward and remove spool Remove and discard ribbon 2 Insert new right Ribbon Spool with hex hole fitted on to hex shaft on the right ribbon feed ratchet Thread ribbon as noted in step 1 Insert new left Ribbon Spool with hex hole fitted on to hex shaft on the left ribbon feed ratchet Turn right Ribbon Spool counter clockwise to remove excess slack in ribbon Figure 3 front view with cover removed Ribbon Tension Spring Ribbon Tension Spring Ribbon Spool Ribbon Spool Installing the Time Recorder Unpacking and Inspection Carefully unpack your recorder and inspect it for any damage Verify that the following accessories are included three mounting screws a case lock key and the General Service Instructions Report damage or shortag
Download Pdf Manuals
Related Search