Calculated Industries Scale Master Pro XE
Contents
1. ON CLEAR K Constant Clear Clears the constant value SUB Subtract Mode Toggles subtract mode on and off When subtract mode is on rolling forward or backward will subtract from the displayed measurement Press SUB a second time or press ON CLEAR to turn subtract mode off User s Guide 8 USING THE SCALE MASTER PRO XE Rotate to Adjust Wheel Adjusting the Wheel The Celcon polymer wheel can be adjusted for each user s preference To adjust the wheel take a small flat head jeweler s screwdriver and slightly rotate the screw located near the wheel tip Rotating the screw about 1 4 to 1 3 turn should be sufficient Rotating the screw within those two values should adjust the wheel between free spinning which is too loose to skidding which is too tight 9 Scale Master Pro XE Preferences Preferences allow customization of how the Scale Master Pro XE functions during certain operations The following preferences are available Button Beep butn Toggles on or off the beep sound that occurs at the press of a button or during auto count Beep On Button beep on Beep Off Button beep off Rolling Click roll Toggles on or off the clicking sound that occurs while rolling Clic On Rolling click on Clic Off Rolling click off Stored Value Display Stor Toggles whether the value remains displayed or is cleared after being stored Clr Led2. auto count constant and height Will scroll down through the preferences A Up Arrow Increases the number when setting values for custom scales auto count constant and height Will scroll up through the preferences Measuring Keys L Length Enters the displayed measurement into length RCL L Length Recall Displays the stored length value On a clear display L can be pressed without RCL ON CLEAR L Length Clear Clears the length value W LxW Width Area Enters the displayed measurement into width The total area will be displayed when the width is entered Repeated presses will scroll through the following results 5 Scale Master Pro XE 1 Area 2 Perimeter 3 Volume if Height is entered 4 Wall Area if Height is entered 5 Stored Height if Height is entered 6 Stored Length 7 Stored Width RCL W LxW Width Recall Displays the stored width value Ona clear display W LxW can be pressed without RCL ON CLEAR W LxW Width Clear Clears the width value SET L H Height Set Enters the height setting mode See the Setting a Height section RCL SET L Height Recall Displays the stored height value SET W LxW LxWxH Volume After pressing SET repeated presses of W LxW will scroll through the following results 1 Volume if Height entered 2 Wall Area if Height entered 3 Stored Height if Height
3. Custom Scale Setting an Auto Count Setting a Constant Additional Constant Functions es Setting a Height 27 Finding Area and Volume Finding Area Finding Volume Additional Area Volume Functions Connecting to a PC optional Appendix Error Auto Range Function Interference Battery Automatic Shut Off Battery Replacement Default Settings Specifications Repair and Return Warranty FCC Class Looking for New Ideas Contact Us GETTING STARTED Key Definitions Operation Keys ON CLEAR On Clear Turns power on Press once to clear the display This will not clear the last rolled measurement as it is a permanent value and can be recalled to the main display at any time by pressing RCL RCL SET ON CLEAR Off Turns power off Turning power off clears the display and semi permanent values length width count All permanent values and settings such as modes scales and units remain intact Holding down the ON CLEAR key for 2 seconds also powers the unit off ON CLEAR MODE Clear All Clears all values including memory Resets all permanent settings except Preferences SET ON CLEAR to turn the device off then MODE ON CLEAR Software Reset Clears all values including memory Resets all permanent settings including Preferences Scale Master Pro XE RESE
4. Display cleared No Cir Display not cleared cont d User s Guide 10 contd PC Terminate End PC Determines where the cursor moves after a value is sent to the PC The settings represent the key being pressed on the PC keyboard Enter PC Enter Tab PC Tab Left PC Left Arrow Right PC Right Arrow Up PC Up Arrow Dn PC Down Arrow None No Terminate PC Send Display SEnd PC Toggles whether the value remains displayed or is cleared after being sent to the PC Clr Led Display cleared No Cir Display not cleared PC Send Beep SEnd PC Toggles whether or not a beep sounds when a value is sent to the PC It is a single beep for a successful send and a double beep for an unsuccessful send or error Beep On Button beep on Beep Off Button beep off 11 Scale Master Pro XE Setting Preferences 1 2 3 Press SET MODE to access the preferences Press the M A key to move up or the RCL key to move down through the list of preferences When the preference to be changed is displayed press the W LxW gt key to move forward or the amp key to move backwatd through the settings for the selected preference Once the desired setting is displayed press the M A RCL V key to move to another preference or press SET to save and exit Imperial Metric Modes The Scale Master Pro XE is set up
5. L to access the height function The appropriate annunciator will begin flashing FT IN for Imperial mode or M for Metric mode An H will appear in the display To change the units of measurement press UNITS until your desired units appear Press the W LxW gt or the L 4 key to begin setting the distance The selected digit will start flashing Press M A to increase or RCL W to decrease the selected digit Press the W LxW gt key to move to the next digit to the right or the L 4 key to move back to the left Once the desired value has been entered press the SET key to save and exit Finding Area and Volume The Scale Master Pro XE can calculate Area and Volume once you have your values set for Length Width and for Volume Height 27 Scale Master Pro XE Finding Area 1 Roll the first side and press the L key to store as Length 2 Roll the second side and press W LxW to store as Width The main display will show the calculated Area Finding Volume To access Volume after you have your values set for Length Width and Height press SET W LxW Continued presses of the W LxW key will display the following results 1 Volume 2 Wall Area 3 Height 4 Stored Length 5 Stored Width 6 Area 7 Perimeter If Height is not entered a 0 will be displayed and continued presses of W LxW will not redisplay the xero volume Wall Area and Hei
6. designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reotient or relocate the receiving antenna Increase the separation between equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including inteference that may cause undesired operation Looking for New Ideas Calculated Industries a leading manufacturer of special funct
7. exact points you ate measuring Otherwise your roll may not be accurate see the second picture in the Operation section 4 Press the ON CLEAR key to clear the display and begin a new measurement 17 Scale Master Pro XE Using the Memory Function The Memory function allows you to add rolled or counted values However you cannot add dimensioned rolled and non dimensioned counted values together To add rolled values 1 Roll the first value Press M The Memory indicator appears and the value is added to Memory 2 Roll the next value Press M This value is added to your previous value stored in Memory 3 You can continue to add values using the M key Press RCL M to review the total in Memory Note For count values you must press the COUNT key to count your value Then press RCL COUNT 0 move the count value to the main display Press M to add this value to Memory See the Function Keys section for additional memory functions User s Guide 18 Additional Memory Functions SET M Subtracts the value in the main display from the value stored in Memory RCL M Displays the total accumulated value in Memory Repeated presses of M will toggle between total accumulated value number of entries in Memory and average value of all entries in Memory ON CLEAR M Clears the Memory register Using Ruler Mode Your Scale Master Pro XE can b
8. Scare MASTER Pro XE ADVANCED DIGITAL PLAN MEASURE Model 6135 User s Guide 1 2 L3 4 5 6 Shown with E optional PC 10 drywa interface cable 11 Elect Part 4 5006 12 _ CALCULATED JI INDUSTRIES FAST ACCURATE RELIABLE Scale MASTER PRO XE Introduction The Scale Master Pro XE Multi Scale Digital Plan Measure has been specifically designed to simplify takeoffs from architectural and engineering drawings Finds linear measurements of any shape Finds rectangular areas and volumes Converts between scales and dimensions Built in push button counter Auto Count function Constant K function Subtract function Custom Scales that let you define and roll in any scale TABLE OF CONTENTS Getting Started Key Definitions Operation Setup Keys Measuring Ki Function Keys Using the Scale Master Pro XE Adjusting the Wheel Preferences 10 Imperial Metric Modes 12 Built In Scales 213 Impetial Standard Units 13 Metric Units 4 Changing Modes 415 Changing Scales 15 Changing Units 45 Locking Modes Scales and Units 15 ODGratiOfi 6 Rolling a Measurement 7 Using the Memory Function 8 Additional Memory Functions 19 Using Ruler Mode Programming Mode Setting Custom Scales Rolling a Custom Scale Entering a
9. T Hardware Reset If your Scale Master Pro XE should ever lock up use a paperclip or similar size object to press the RESET hole Clears all values including memory All permanent settings including Preferences remain intact SET Set Key Used with other keys to access second functions and place the Scale Master Pro XE into programming mode If in programming mode already pressing SET will store the displayed value and exit programming mode A press of SET after rolling locks the measurement While locked the displayed value will not be affected by rolling the Scale Master Pro XE A second press of SET will unlock the measurement RCL Recall Key Used to recall stored values When you press RCL RCL the last value rolled is displayed allowing roll to continue from this value Recalling any other value disables measuring until the recalled value is cleared with a press of ON CLEAR IMP MET Imperial Metric Switch Toggles between Imperial and Metric modes User s Guide 2 LOCK Lock Switch The Lock Switch is located on the side of the unit When the lock is activated a lock symbol will be displayed in the LCD While active you cannot alter Scales Modes Units Preferences or the IMP MET Imperial Metric switch You also cannot perform a Clear All or a Software Reset It is advised to use the Scale Master Pro XE in the locked position unless you are specifically setting or changin
10. e used as a rolling ruler which is especially useful for measuring irregular shapes To change to Ruler Mode press the MODE key until the Ruler Mode is indicated in the upper display as TAPE Begin rolling 19 Scale Master Pro XE Programming Mode The Scale Master Pro XE allows you to pre set frequently used values including e Custom Scales 5 Imp 5 Met e Auto Count distance K Constant value e Height value To begin setting values press the SET key and then the desired key to be programmed The following keys are used in programming mode UNITS Toggles through available units W LxW gt Advances the cursor to the next place to the right L Moves the cursor back to the next place to the left M A Increases the selected value RCL Decreases the selected value ON CLEAR Exits without saving any changes SET Exits and saves changes User s Guide 20 Setting Custom Scales You can store ten Custom Scales five in Imperial Mode and five in Metric Mode You can set a custom scale two ways by rolling in a known distance or by entering the exact distance Rolling a Custom Scale 1 Press MODE until OPEN being a number 1 5 appears in the scale box display 2 Press SET SCALE ROLL will appear in the main display 3 Roll desired distance ROLLING now appears in the main display 4 Press SCALE The annuncia
11. entered 4 Stored Length 5 Stored Width 6 Area 7 Perimeter User s Guide 6 Function Keys M Memory Plus Adds the displayed value to the accumulative value RCL M Memory Recall Displays the value stored in accumulative memory ON CLEAR M Memory Clear Clears the accumulative memory value SET M M Memory Minus Subtracts the displayed value from the accumulative memory SUB M will perform the same function COUNT Count Increases the count value by one SUB COUNT Count Subtract Decreases the count value by one RCL COUNT Count Recall Displays the count value in the main display ON CLEAR COUNT Count Clear Clears the count value SET COUNT Auto Count Enters auto count setting mode See the Setting an Auto Count section 7 Scale Master Pro XE RCL SET COUNT Auto Count Recall Displays the stored Auto Count value P PC PC Send When connected to a PC sends the value from the main display of the Scale Master Pro XE to the PC All values are sent in decimal format K Constant Add Adds the constant value to the displayed measurement value SET K Constant Set Enters constant setting mode See the Setting a Constant K section SUB K Constant Subtract Subtracts the constant value from the displayed measurement value RCL K Constant Recall Displays the stored constant value
12. es Repeated presses of the SCALE key will scroll through the list of available scales Holding SUB when pressing SCALE will scroll backward through the list of available scales Changing Units Repeated presses of the UNITS key will scroll through the list of available units Holding SUB when pressing UNITS will scroll backward through the list of available units Locking Modes Scales and Units Your Scale Master Pro XE comes equipped with a lock switch that prevents inadvertently changing drawing scales When the lock is activated a lock symbol will be displayed in the LCD While active the Mode Scale and Units cannot be revised 15 Scale Master Pro XE Operation Do not rotate Try to keep the unit in the same U upright position while you roll Rotating the unit while rolling will add or subtract distance Begin and end measurements from this point User s Guide 16 Rolling a Measurement To take a measurement with the Scale Master Pro XE 1 Turn the unit on If the display does not show zeto 0 press the ON CLEAR key to clear the display 2 Select your type of scale by pressing the MODE key Then press the SCALE key to select your scale 3 Begin rolling The display will register your measurements When you roll the unit be sure to hold the unit upright see the first picture in the Operation section Also make sure you start and stop at the
13. g a setting Setup Keys MODE Mode Selection Repeated presses of MODE will scroll through the available modes See Changing Modes section SUB MODE Scrolls Back Modes Holding SUB and repeated presses of MODE vill scroll backward through the available modes SCALE Scale Selection Repeated presses of SCALE will scroll through the available scales See Changing Scales section 3 Scale Master Pro XE SUB SCALE Scrolls Back Scales Holding SUB and repeated presses of SCALE will scroll backward through the available scales UNITS Unit Selection Repeated presses of UNITS will scroll through the available units of measurement See Imperial Units and Metric Units sections SUB UNITS Scrolls Back Units Holding SUB and repeated presses of UNITS will scroll backward through the available units SET MODE Preferences Accesses the preference settings See Preferences section 4 L Left Arrow Moves to the left when setting values for custom scales auto count constant and height Will scroll back through available settings within the preferences W LxW Right Arrow Moves to the right when setting values for custom scales auto count constant and height Will scroll forward through available settings within the preferences User s Guide 4 V RCL Down Arrow Decreases the number when setting values for custom scales
14. ght do not display if a Height has not been set User s Guide 28 Additional Area Volume Functions RCL L Displays the value stored in the Length register RCL W LxW Displays the value stored in the Width register ON CLEAR L Clears the value stored as Length ON CLEAR W LxW Clears the value stored as Width Connecting to a PC optional The Scale Master Pro XE has a computer interface connection so that you can use it with estimating and spreadsheet software programs Like your keyboard it sends a single value from the Scale Master Pro XE to the selected cell in your program Only the value currently on the main display will be sent to the PC To send the displayed value to your PC press the f PC key Note When connected to a PC a small PC shaped icon D will appear in the upper display indicating a valid connection has been established This icon will be displayed only when the USB cable is securely connected to the Scale Master Pro XE and the PC 29 Scale Master Pro XE APPENDIX Error Auto Range Function Error Message 1f you make an incorrect entry such as trying to add dimensioned and non dimensioned values together the Scale Master Pro XE will display the word ERROR Press ON CLEAR to clear Auto Range Function If the value is too large to display in the selected units of measurement the answer will be displayed in the next larger measurement
15. he product repaired in your atea you may contact CI to obtain current product repair information and charges including freight and duties Disclaimer CIMAKES NO WARRANTY OR REPRESENTATION EITHER EXPRESS OR IMPLIED WITH RESPECT TO THE PRODUCT S QUALITY PERFORMANCE MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE AS A RESULT THIS PRODUCT INCLUDING BUT NOT LIMITED TO KEYSTROKE PROCEDURES MATHEMATICAL ACCURACY AND PREPROGRAMMED MATERIAL IS SOLD 5 15 AND YOU THE PURCHASER ASSUME THE ENTIRE RISK AS TO ITS QUALITY AND PERFORMANCE IN NO EVENT WILL CI BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY DEFECT IN THE PRODUCT OR ITS DOCUMENTATION The warranty disclaimer and remedies set forth above are exclusive and replace all others oral or written expressed ot implied No CI dealer agent or employee is authorized to make any modification extension or addition to this warranty Some states do not allow the exclusion or limitation of implied warranties or liability for incidental ot consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state User s Guide 36 FCC Class B Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are
16. ion calculators and digital measuring instruments is always interested in new product ideas in these areas If you have a new product idea please visit our Bright Idea page at www calculated com brightidea asp For suggestions about improving this product or other products please visit us at www calculated com under Contact Us Thank You 37 Scale Master Pro XE Contact Us Mail E Calculated Industries Inc 4840 Hytech Drive Carson City NV 89706 U S A Phone 775 885 4900 Fax 775 885 4949 E mail techsup calculated com World Wide Web www calculated com User s Guide 38 CALCULATED Jj 127 INDUSTRIES Software copyrighted and licensed to Calculated Industries by Scale Master Technologies LLC 2009 User s Guide copyrighted by Calculated Industries 2009 Scale Master and Calculated Industries are registered trademarks of Calculated Industries Inc ALL RIGHTS RESERVED CALCULATED INDUSTRIES 4840 Hytech Drive Carson City NV 89706 U S A 1 800 854 8075 or 1 775 885 4900 Fax 1 775 885 4949 E mail info calculated com www calculated com Designed in the U S A Printed in China 10 08 rece UG6135E A
17. it will beep each time you roll the programmed distance The count number in the display will increase Press SET COUNT to exit Auto Count mode Setting a Constant K This function is used to store a constant value Once a constant value has been stored pressing K will add that value to the displayed measurement To set a constant 1 Press SET K to access the constant function The appropriate annunciator will begin flashing FT IN for Imperial Mode ot for Metric Mode PLUSk will appear in the display 25 Scale Master Pro XE To change the units of measurement press UNITS until your desired units appear Press the W LxW gt or the L 4 key to begin setting the distance The selected digit will start flashing Press M A to increase or RCL W to decrease the selected digit Press the W LxW gt key to move to the next digit to the right or the L key to move back to the left Once the desired value has been entered press the SET key to save and exit Additional Constant Functions RCL K Allows you to verify the current constant value SUB K Subtracts the constant value from the displayed measurement value ON CLEAR K Resets the constant value to zero User s Guide 26 Setting a Height The height function is used to enter a height value for finding volume To set a Height 1 Press SET
18. of one 1 year ftom the date of original consumer purchase in the If a defect exists during the warranty period at its discretion will either repair using new or remanufactured parts or replace with a new or remanufactured unit the product at no charge THE WARRANTY WILL NOT APPLY TO THE PRODUCT IF IT HAS BEEN DAMAGED BY MISUSE ALTERATION ACCIDENT IMPROPER HANDLING OR OPERATION OR IF UNAUTHORIZED REPAIRS ARE ATTEMPTED OR MADE SOME EXAMPLES OF DAMAGES NOT COVERED BY WARRANTY INCLUDE BUT ARE NOT LIMITED TO BATTERY LEAKAGE BENDING A BLACKINK SPOT OR VISIBLE CRACKING OF THE LCD WHICH ARE PRESUMED TO BE DAMAGES RESULTING FROM MISUSE OR ABUSE To obtain warranty service in the U S please go to the website A repaired or replacement product assumes the remaining warranty of the original product or 90 da whichever is longer Non warranty Repair Service USA Non watranty repair covers service beyond the warranty period or service requested due to damage resulting from misuse or abuse Contact Calculated Industries at the number listed above to obtain current product repair information and charges Repairs are guaranteed for 90 days 35 Scale Master Pro XE Repair Service Outside the USA To obtain warranty or non warranty repair service for goods purchased outside the U S contact the dealer through which you initially purchased the product If you cannot reasonably have t
19. ratios 6 Press M A to increase or RCL V to decrease the selected digit Press the W LxW gt key to move to the next digit to the right or the L 4 key to move back to the left 7 Once the desired value has been entered press SET to store value and exit the programming mode Press RCL SCALE while in custom mode to display the current custom scale 23 Scale Master Pro XE Setting an Auto Count The Scale Master Pro XE has an Auto Count function that allows you to count how many times you ve rolled a certain distance You will hear a beep each time you roll that distance To set an Auto Count 1 Press SET COUNT to access the Auto Count function The appropriate annunciator will begin flashing FT IN for Imperial mode or for Metric mode AUTO COUNT will appear in the display To change the units of measurement press UNITS until your desired units appear Press the W LxW gt or the L 4 key to begin setting the distance The selected digit will start flashing Press M A to increase or RCL W to decrease the selected digit Press the W LxW gt key to move to the next digit to the right or the L 4 key to move back to the left cont d User s Guide 24 contd 4 Once the desired value has been entered press SET to save changes and put the unit into Auto Count mode Roll a distance The un
20. splay Clear LCD PC Send Beep On User s Guide 32 Specifications Power Source Two 3 Volt CR 2032 lithium batteries Approximately 400 hours normal use Display Method LCD with commas annunciators and zero suppression Display Capacity Main Display 9 999 999 7 digits Resolution Accuracy 025 Inch 99 75 Note Based on start stop point and scale magnitude users typically experience 2 396 rolling error Dimensions 7 2 x 1 8 x 0 4 182mm x 45mm x 10mm 33 Scale Master Pro XE Repair and Return Repair and Return Information Return Guidelines 1 Please read the Warranty in this User s Guide to determine if your Calculated ndustries product remains under warranty before calling or returning any device for evaluation or repairs f your product won t turn on check the atteries as outlined in the User s Guide f you need more assistance please go to out website listed below f you believe you need to return your product please call a Calculated ndustries representative between the hours of 7 00am to 4 30pm Pacific Time for additional information and a Return Merchandise Authorization RMA Call Toll Free 1 800 854 8075 Outside USA 1 775 885 4900 www calculated com warranty User s Guide 34 Warranty Warranty Repair Service USA Calculated Industries warrants this product against defects in materials and workmanship for a period
21. to use Imperial Standard dimensional units by default The Scale Master Pro XE can be set to Metric Mode by switching the IMP MET switch to MET While in Metric mode MET will remain lit in the display User s Guide 12 Built In Scales Imperial Standard Units Architect ARCH 1 foot 1 4 3 8 1 2 3 4 1A 17 3 2 1 21 2 3 1 3 4 1 47 1 32 1 16 3 32 1 8 3 16 Engineer ENGI 1 inch 10 0 20 0 30 0 40 0 50 0 60 0 83 3 100 0 166 6 200 0 250 0 13 Scale Master Pro XE Engineer ll ENGII 1 inch 300 0 333 3 400 0 416 6 500 0 583 3 600 0 625 0 666 6 750 0 1 000 0 1 200 0 2 000 0 3 000 0 Map MAP 1 inch 1 0 Mi 1 5 Mi 2 0 Mi 3 0 Mi 4 0 Mi 5 0 Mi 6 0 Mi 10 0 Mi 20 0 Mi 24 0 Mi 25 0 Mi Metric Units Architect Engineer Engineer ll Map ARCH ENGI ENGII MAP 1 50 1 100 0 1 1 000 1 100k 1 75 1 125 0 1 1 250 1 125k 1 1 1 150 0 1 1 500 1 200k 1 2 1 200 0 1 1 625 1 250k 1 3 1 250 0 1 2 000 1 500k 1 4 1 300 0 1 2 500 1 1 000 1 5 1 400 0 1 5 000 1 2 000 1 10 1 500 0 1 6 000 1 2 500 1 20 1 10k 1 25 1 12 5k 1 30 1 20k 1 40 1 25k 1 50k User s Guide 14 Changing Modes Repeated presses of the MODE key will scroll through the list of available modes Holding SUB when pressing MODE will scroll backward through the list of available modes Changing Scal
22. tor will begin flashing FT IN for Imperial Mode M for Metric Mode Unt To change the units of measurement press UNITS until your desired units appear Press the W LxW gt or the L 4 key to begin setting the distance The selected digit will start flashing 21 Scale Master Pro XE Press M A to increase or RCL W to decrease the selected digit Press the W LxW gt key to move to the next digit to the right or the L key to move back to the left Once the desired value has been entered press SET to store value and exit the programming mode Note Pressing ON CLEAR will exit the programming mode without saving any value as the Custom Scale Entering a Custom Scale 1 Press MODE until OPEN being a number 1 5 appears in the scale box display Press SET SCALE ROLL will appear in the main display Press SCALE again The annunciator will begin flashing FT IN for Imperial Mode The left most digit flashes for Metric Mode Note If in Metric Mode skip to Step 5 cont d 22 User s Guide cont d 4 change the units of measurement press UNITS until your desired units appear Press the W LxW gt or the L 4 key to begin setting the distance The selected digit will start flashing we In Imperial mode the scale will be one inch equals the distance you entered In Metric mode entered scales are direct
23. units instead of showing an error for example 10 000 000 MM cannot be displayed so 10 000 M will be displayed instead Interference Exposure to direct light or close proximity to cell phones and other electronic devices may cause interference with the Scale Master Pro XE device and result in erroneous measurements User s Guide 30 Battery Automatic Shut Off The Scale Master Pro XE is powered by two 3 Volt CR 2032 Lithium batteries 6 volts total To conserve battery power the unit will shut itself off if it is not used for 4 6 minutes Press the ON CLEAR to restore power All registers and settings remain intact including all temporary registers Battery Replacement replace the batteries 1 To remove battery door release snap lock in slot and lift 2 Remove batteries and replace with new batteries positive side up 3 To replace the door slide it at an angle and push down 31 Scale Master Pro XE Default Settings The following ate the factory defaults of the Scale Master Pro XE Default Default Settings Imperial Metric Mode ARCH ARCH Scale 1 4 1 50 Custom Scales 1 1 1 Linear FT IN MM Area SQFT SQM Volume CU YD CUM Length 0 0 0 00 Width 0 0 0 00 Height 0 0 0 00 K constant 0 0 0 00 Auto Count 0 0 0 00 Count 0 0 Subtract Mode Off Off Preferences Default Button Beep On Rolling Click On Stored Value Display Clear LCD PC Terminate Enter PC Send Di
Download Pdf Manuals
Related Search