Home

Philips CE135BT

image

Contents

1. Always follow the instructions in this chapter in sequence These instructions are for a typical installation However if your car has different requirements make the adjustment accordingly If you have any question regarding installation kits consult your local retailer e This system is designed for negative ground earth 12V DC operation only e Always install this system in the car dashboard Other locations can be dangerous as the rear of the system heats up during use e To avoid short circuit before you connect make sure that the ignition is off e Make sure that you connect the yellow and red power supply leads after all other leads are connected e Make sure that all loose leads are insulated with electrical tape e Make sure that the leads do not get caught under screws iron parts that will move e g seat rail e Make sure that all ground earth leads are run to a common ground earth point Use only the supplied mounting hardware for a safe and secure installation e Improper fuses can cause damage or fire When you need to change the fuse consult a professional e When you connect other devices to this system make sure that the rating of the car circuit is higher than the total fuse value of all the connected devices e Never connect speaker wires to the metal body or chassis of the car e Never connect speaker wires with stripes to one another Connect wires
2. Your system consists of materials which can be recycled and reused if disassembled by a specialized company Please observe the local regulations regarding the disposal of packaging materials exhausted batteries and old equipment Trademark notice Ay Plays n Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries Other trademarks and trade names are those of their respective owners Copyright 2014 WOOX Innovations Limited All rights reserved Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N V and are used by WOOX Innovations Limited under license from Koninklijke Philips N V Specifications are subject to change without notice WWOOX reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly EN 19 PHILIPS Specifications are subject to change without notice 2014 WOOX Innovations Limited All rights reserved Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N V and are used by WOOX Innovations Limited under license from Koninklijke Philips N V 2 x CE135BT_10_UM_V2 0
3. Note To the 12V car battery which is energized at all times Yellow strip e Make sure that all loose leads are insulated with electrical tape e Consult a professional to connect wires as instructed below 1 Check connect he car s wiring carefully and t them to the the ISO male ors connect Connect the antenna and amplifier as illustrated if applicable co ssn ISO male Connect to connectors a Green strip black Rear left speaker Sockets on rear panel External sockets or edged green strip connectors b White strip black Front left speaker 4 For ISO male As indicated edged white strip connectors above c Gray strip black Front right speaker 2 REARL Rear left speaker F grey a x 3 REARR Rear right speaker urple strip ack ear rignt speaker 4 ANTENNA Aea edged purple strip e Red strip gnition key 12V S r UpIEStIp sateen DC when ON control module ACC f Blue strip Motor electric Tip antenna relay control lead e The pin arrangement for the ISO connectors depends g White edged blue Amplifier rela oe strip control lead h Black strip Ground Mount into the dashboard fthe car does not have an on board drive or navigation co
4. play all tracks in the storage device in sequence 7 Use Bluetooth devices With this car audio system you can listen to audio from a player or make a call through Bluetooth Connect a device e WOOX Innovations does not guarantee the compatibility with all Bluetooth devices e Before pairing a device with this system read its user manual for Bluetooth compatibility e Make sure that Bluetooth function is enabled on your device and your device is set as visible to all other Bluetooth devices e At one time you can connect only one Bluetooth device to this system e The operational range between this system and a Bluetooth device is approximately 3 meters 9 feet e Any obstacle between this system and a Bluetooth device can reduce the operational range e Keep away from any other electronic device that may cause interference On your device follow the steps below 1 Search for Bluetooth devices 2 Inthe device list select CE135BT 3 Enter the default password 0000 and then confirm the password entry L gt Ifthe pairing succeeds PAIRED is displayed on the LCD screen of this system 4 Enable or permit the connection with CE135BT L gt lf the connection succeeds CONNECTED scrolls and is displayed on the LCD screen of this system L gt Ifthe connection fails FAILED is displayed on the LCD screen of this system Disconnect a device 1 Press and hold
5. DSP y to display available out the current track y to display available RDS information D ress and hold to display the set clock AS SOURCE Ea AUDIO Press repeatedly select a source n radio mode press and hold to activate the automatic search of radio stations Press repeatedly to select a preset sound equalizer Press and hold to activate the setup of bass treble balance and fader Press to turn on the system Press and hold to turn off the system Press to mute the speakers or release hem from mute status Press to confirm an option Rotate to switch between menu options Rotate to adjust the volume level For wma and mp3 tracks press to select the next folder Press and hold to activate the selection of listening zones Press to select a tuner band 14 gt gt I Tune to a radio station Press to skip to the previous next rack Press and hold to rewind a track or search fast forward EN 5 Press he D effect onc Slot Press nsert RESET Press to reset the system to factory o enable or disable the maximum volume Press and hold to enable or disable BB dynamic bass boost sound o hang up a call Press and hold to reject an incoming call for SD SDHC card an SD SDHC card default settings 3 Install the car audio system Caution e Use the controls only as stated in this user manual
6. 3 Press and hold 1 33 wl 2 3REP SHUF 4 5 or gt i 6 to store the radio station at the selected channel e To select a stored radio station press 123 wa 2 3REP sHUF 4 5 or U6 EN 11 6 Play froma storage device 12 Connect a compat or SD SDHC card e Foran SD SDHC card detach the front panel first insert the card into the card slot and then attach the front panel Switch the source SDHC If the play does no EN o USB or SD start press gt 6 ible USB storage device Button Function a v MENU ZONE Press repeatedly o select a folder PIG Pause or resume play 14d gt gt I Press to play the rack previous or next la gt gt I DISP Press and hold to Press repeatedly available informat current track rewind a track or search forward fast o display ion about the 3REP Press repeatedly mode REP ONE re track o select a repeat peat the current e RPT FLD repeat all tracks in the current folder or RPT ALL rep eat all tracks in the storage device SHUF 4 Press repeatedly to select a play mode e SHU ALL pla randomly y all tracks e SHU FLD play tracks in the current folder randomly or e SHU OFF
7. 6 e n radio mode press to select the preset radio station of No 5 e In radio mode press and hold to store he current radio station at channel 0 5 SHUF 4 e n radio mode press to select the preset radio station of No 4 e In radio mode press and hold to store he current radio station at channel o 4 For wma and mp3 tracks press repeatedly to select a play mode play all tracks randomly SHU ALL play racks in the current folder randomly SHU FLD or play all tracks in the storage device in sequence SHU OFF 3REP e In radio mode press to select the preset radio station of No 3 e In radio mode press and hold to store he current radio station at channel 0 3 For wma and mp3 tracks press repeatedly to select a repeat mode repeat the current track REP ONEJ repeat all tracks in the current folder RPT FLD or repeat all tracks in the storage device RPT ALL w2 e In radio mode press to select the preset radio station of No 2 e In radio mode press and hold to store he current radio station at channel 0 2 For wma and mp3 tracks press to access the folder list 12 n radio mode press to select the preset radio station of No 1 0 1 Press repeated information ab Press repeated n radio mode press and hold to store he current radio station at channel For wma and mp3 tracks press to access the track list
8. MENU to access the system menu 2 Pressa repeatedly until DISCONN is displayed 3 Press O amp K Ly WAIT is displayed with and blinking alternately until DISCNN OK scrolls Tip e You can also complete the disconnection on your device Reconnect a device Some Bluetooth devices support the automatic reconnection with a paired Bluetooth device If your device does not support automatic reconnection reconnect it with this system manually 1 Press and hold MENU to access the system menu 2 Pressa repeatedly until CONNECT is displayed 3 Press O L gt WAIT is displayed with and blinking alternately until CONNECTED scrolls or FAILED appears Ly If CONNECTED scrolls this system is reconnected to the last connected device EN 13 Tip e You can also complete the reconnection on your device Play audio from a Bluetooth device If the connected Bluetooth device supports Advanced Audio Distribution Profile A2DP you can listen to tracks that are stored on the device through the system If the device also supports Audio Video Remote Control Profile AVRCP profile you can control play on the system or with its remote control 1 Play a track on the connected device 2 Press SOURCE repeatedly to switch the source to BT AUDIO L Play starts automatically e To pause or resume play press 6 e To skip to the previous or next tra
9. the terminal hat is always live Display shows ERR 12 e Data error Check the USB storage device or SD SDHC card 14 Notice Any changes or modifications made to this device that are not expressly approved by WOOX Innovations may void the user s authority to operate the equipment Compliance C 1177 This product complies with the radio interference requirements of the European Community A copy of the EC declaration of Conformity is available in the Portable Document Format PDF version of the user manual at www philips com support Care of the environment ab Your product is designed and manufactured with high quality materials and components which can be recycled and reused R When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health Environmental information All unnecessary packaging has been omitted We have tried to make the packaging easy to separate into three materials cardboard box polystyrene foam buffer and polyethylene bags protective foam sheet
10. Always there to help you Register your product and get support at www philips com support if oN Question Contact Philips CE135BT User manual PHILIPS Contents 1 Safety 2 2 Your car audio system 3 Introduction 3 What s in the box 3 Overview of the system 4 3 Install the car audio system 6 Connect wires 7 Mount into the dashboard 8 Attach the front panel 9 4 Get started 10 For the first time use 10 Set the clock 10 Select a source 10 5 Listen to radio 10 Select a tuner region 10 Select a tuner sensitivity 10 Enable the RDS function 11 Search for a radio station 11 Store radio stations in memory 11 6 Play from a storage device 12 7 Use Bluetooth devices 13 Connect a device 13 Play audio from a Bluetooth device 14 Make a call 14 8 Listen to an external device 15 9 Charge your USB device 15 10 Adjust sound 16 11 Reset the system 12 Product information 17 Product Information 17 13 Troubleshooting 18 14 Notice 19 Compliance 19 Care of the environment 19 Trademark notice dg Copyright 19 EN 1 Safety Read and understand all instructions before you use this device If damage is caused by failure to follow instructions the warranty does not apply odification of the product could result in hazardous radiation of EMC or other unsafe operation The device is designed for negative ground earth 12V DC operation only To ensure safe driving adjust the volu
11. LOC OFF Search for radio stations with strong and weak signals Enable the RDS function Note e The RDS function is enabled by default Only when the RDS function is enabled RDS related settings can be accessed 1 Press and hold to access the system menu 2 Press X repeatedly until RDS ON or RDS OFF is displayed 3 Rotate to select RDS ON L gt The RDS function is enabled e To disable the RDS function rotate amp to select RDS OFF Search for a radio station Store radio stations automatically 1 Switch the source to RADIO 2 Press BAND vu Or zx repeatedly to select a band 3 Press and hold AS SOURCE until STORE is displayed L gt After the search is complete the first stored radio station is broadcast automatically e To select a stored radio station press 17 wi 2 3REP SHUF 4 5 or PUG Search for a radio station automatically Press kid or PPI to search for the previous or next radio station with strong signals Search for a radio station manually 1 Press and hold K or PP until M blinks 2 Press 4 or DDI repeatedly until the target frequency is displayed Store radio stations in memory Note e You can store a maximum of six stations in each band Store radio stations manually 1 Press BAND ssu Or zx repeatedly to select a tuner band 2 Tune to the radio station that you want to store
12. MHz FM 100kHz per step in auto search and 50kHz per step in manual search Usable sensitivity 8 uV FM S N 20 dB 522 1620 KHz 9 kHz 530 1710 kHz 10 kHz Frequency range AM MW Usable sensitivity 30 uV AM MW S N 20 dB Output Class 2 power Frequency 2 4000 GHz 2 4835 GHz ISM band Band Range 3 meters free space Standard Bluetooth 2 0 specification Compatible USB devices e USB flash memory USB 1 1 host with interface reading all speed support 1 1 2 0 e USB flash players USB 1 1 host with interface reading all speed support 1 1 2 0 Supported formats e USB or memory file format FAT12 FAT16 FAT 32 e P3 bit rate data rate 32 320 Kbps and variable bit rate WMAYV4 V7 V8 V9 L1 L2 e P3 sampling frequencies 8 48 kHz e P3 Bit rates 8 320 kbps variable bit rates e WMA sampling frequencies 32 kHz 441 kHz 48 kHz e WMA Bit rates 32 192 kbps variable bit rates Directory nesting up to a maximum of 8 levels umber of albums folders CD maximum 99 USB or memory maximum 99 umber of tracks titles CD maximum 999 depending on number of album USB or memory maximum 999 ID3 tag v2 0 or later Unsupported formats Empty albums an empty album is an album that does not contain MP3 WMA files and is not be shown in the display EN 17 18 EN Unsupported file formats are skipped For example Wo
13. V8 V9 L1 and L2 Sampling frequencies 44 1 kHz 48 kHz Bitrates 64 192 kbps and variable bitrates ID3 tagV2 0 or later e Unsupported files AAC WAV and PCM files DRM protected WMA files way m4a m4p mp4 and aac WMA files in lossless format What s in the box Check and identify the contents of the package Main unit with a sleeve Carrying case with front panel included Trim plate Disassembly tool X 2 ISO male connector X 2 User manual GUHO GA EN 3 Overview of the system PHILIPS CarStudio AUDIO SYSTEM CEI358T o ae SOURCE DISP A o gt m20 O3REP SHUF 4o 05 PIG O a e Connect to a USB storage device Unlock the front panel AUDIO IN Connect to the audio output socket usually the headphone socket of an external device For wma and mp3 tracks press to select the previous folder e Press and hold to access the system menu D rug e Press to select a tuner band e Start pause or resume the play of tracks p e Return to the previous menu LCD screen e In radio mode press to select the preset radio station of No 6 4 EN e In radio mode press and hold to store he current radio station at channel 0
14. ayed with time digits blinking 3 Rotate amp anti clockwise to set the hour 4 Rotate amp clockwise to set the minute Select a source Press AS SOURCE repeatedly to select a source e RADIO Listen to FM AM radio e AUDIO IN Listen to the audio input through the AUDIO IN socket USB When a USB storage device is connected and recognized you can select this source to play audio files that are stored on it SD SDHC When an SD SDHC card is inserted and recognized you can select this source to play audio files that are stored on it 10 EN 5 Listen to radio Select a tuner region You can select a radio region that matches your location 1 Press and hold to access the system menu 2 Press X repeatedly until one of the following options is displayed e AREA EUROPE Western Europe e AREA ASIA Asia Pacific AREA M EAST Middle East e AREA AUST Australia e AREA RUSSIA Russia AREA USA United States AREA LATIN Latin America 3 Rotate to select a region Select a tuner sensitivity To search for radio stations with strong signals only or more radio stations you can change the tuner sensitivity 1 Press and hold to access the system menu 2 Press A repeatedly until LOC ON or LOC OFF is displayed 3 Rotate amp to select a setting e LOC ON Search for radio stations with strong signals only e
15. ck press I lt DPI Note e Ifthe connected device does not support the AVRCP profile control play on the connected device Make a call Note e Keep the Bluetooth connection active between the system and your mobile phone Call a number On your mobile phone call a number Ly CALLING is displayed 14 EN Pick up an incoming call When the system receives an incoming call the phone number or PHONE IN is displayed Press to answer the call Reject an incoming call Press and hold 6 until END is displayed End a call To end an on going call press 6 8 Listen to an external device You can use the system to amplify the audio input from an external device for example MP3 player NO 1 Switch the source to AUDIO IN Connect an audio in cable to e the AUDIO IN socket on the system and e the audio output socket usually the headphone socket on the external device 3 Play the external device 9 Charge your USB device You can charge your USB device for example smart phone with this product Note e The output voltage through the USB socket is 5 V with output current 1 0 A Connect your USB device to this product with USB cable Once the USB device is connected and recognized it begins to charge automatically EN 15 10 Adjust sound 11 Reset the system The following operations ar
16. e applicable to all supported media If the system works abnormally reset the system to factory default settings OK Rotate to increase or decrease the volume level O Press to mute the speakers or release hem from mute status sounD Press to enable or disable the ji maximum volume io Press and hold to enable or disable he Dynamic Bass Boost DBB effect sine Press repeatedly to select a sound equalizer ae 1 Press and hold to activate the setup of customized sound equalizer 1 Detach the front panel 2 Press repeatedly to select an option 2 Press the RESET button with the tip of a BAS bass TRE treble BAL ball point pen or toothpick balance or FAD fader L gt All settings are reset to factory default 3 Rotate amp to adjust the setting 16 EN 12 Product information Note e Product information is subject to change without prior notice Product Information General 12V DC 11V 16 V negative ground Power supply Bluetooth Fuse 15A Suitable speaker 4 80 impedance Maximum power 50 W x 4 output Continuous power 22 W x 4 RMS 4 9 output 10 T H D Pre Amp output 25V voltage Aux in level 2 500 mV Dimension Wx H x D 188 x 58 x 110 mm Weight 0 63 kg Radio Frequency range 87 5 108 0
17. me to a safe and comfortable level mproper fuses can cause damage or fire When you need to change the fuse consult a professional Use only the supplied mounting hardware for a safe and secure installation To avoid short circuits do not expose the device to rain or water The device shall not be exposed to dripping or splashing Do not place any sources of danger on he device e g liquid filled objects lighted candles ever insert objects into the ventilation slots or other openings on the device Clean the device with soft damp cloth ever use substances such as alcohol chemicals or household cleaners on the device EN 2 Your car audio system Introduction With this system you can e enjoy audio from USB storage devices SD SDHC card and other external players and Bluetooth device e listen to radio stations You can enrich sound output with these sound effects Dynamic bass boost DBB e Digital sound control DSC Playable media e USB storage device Compatibility USB 2 0 USB 1 1 e Class support MSC Mass Storage Class aximum capacity 32 GB e SD SDHC card aximum capacity 32 GB e Files e File system FAT16 FAT32 e Maximum number of folders 99 e Maximum number of tracks files 999 aximum level of directory 8 mp3 files Sampling frequencies 32 kHz 44 1 kHz 48 kHz Bitrates 8 320 kbps and variable bitrates e wma files Versions V4 V7
18. mputer disconnect the negative terminal of the car battery f the car battery is not disconnected to avoid short circuit make sure that the bare wires do not touch each other 1 ake sure that the car dashboard opening is within these measurements W 4 Slide the unit into the dashboard until you hear a click 53mm 2 Remove the mounting sleeve with the supplied disassembly tools 5 Attach the trim plate 3 Install the sleeve into the dashboard and bend the tabs outward to fix the sleeve 6 Reconnect the negative terminal of the car Detach the front panel battery Note Attach the front panel e Before you insert an SD SDHC card or reset the system detach the front panel e Before you detach the front panel make sure that the 1 Insert the notch on the front panel to the system is turned off chassis on the main unit ooo0000000a0000 00000000000004 1 Press a to release the front panel PIi 2 Pull the front panel outwards to remove it 2 Press the left end of the front panel inwards until it is securely locked with a 000000000800 000000000090 EN 9 4 Get started For the first time use 1 Press to turn on the system L gt PHILIPS is displayed and the device turns to radio mode automatically Set the clock 1 Press and hold to access the system menu Z Press Se repeatedly until CLK is displ
19. rd documents doc or MP3 files with extension dlf are ignored and not played AAC WAV PCM audio files DRM protected WMA files way m4a m4p mp4 aac WMA files in Lossless format 13 Troubleshooting Warning e Never remove the casing of this product To keep the warranty valid never try to repair the product yourself If you encounter problems when using this product check the following points before requesting service If the problem remains unsolved go to the Philips Web page www philips com support When you contact the Consumer Care make sure that the product is nearby and the model number and serial number are available No power or no sound e The power supply from car battery is cut off or the car battery runs out of energy Power the system with car battery Car engine is not on Turn the car engine on Cable is not correctly connected Check connections e The fuse is burnt Replace the fuse Volume is too low Adjust volume e If the above solutions cannot help press the RESET button e Make sure that the current track is in a compatible format Noise during broadcast e Signals are too weak Select other stations with stronger signals e Check the connection of the car antenna Change the broadcast setting from stereo o mono Preset stations are erased e Battery cable is not correctly connected Connect the battery cable to

Download Pdf Manuals

image

Related Search

Related Contents

Scarica l`allegato  Roughness Manual - Roads and Highways Department  Novo Nordisk Insulin Pen 30 User's Manual  Reliable Securing    Bedienungsanleitung DE  Samsung LS15N13W User Manual  USER MANUAL IN ORIGINAL    GPS Multimídia NC300 Manual do Usuário  

Copyright © All rights reserved.
Failed to retrieve file