Home

ParkZone Mini Vapor RTF

1. eum 0600 DSM2 DSMX 4 Channel Transmitter To register your product online go to www parkzone com zone D Charging the Battery Your aircraft comes with a 1S 3 7V DC Li Po battery charger and 1S 3 7V 30mAh 25C Li Po battery Refer to the charging warnings It is recommended to charge the battery pack while you are inspecting the aircraft The flight battery will be required to confirm proper aircraft operation in future steps Remove the cover on the bottom of the charger and install four of the included AA batteries noting proper polarity Replace the cover after the AA batteries are installed Battery Charging Process NOTICE Charge only batteries that are cool to the touch and are not damaged Look at the battery to make sure it is not damaged e g swollen bent broken or punctured 1 Connect the flight battery to the charger connector noting proper polarity 2 Always disconnect the flight battery from the charger immediately upon completion of charging A CAUTION Only use the included charger specifically designed to charge this Li Po battery Failure to do so could result in fire causing injury or property damage A CAUTION Never exceed the recommended charge rate LED Indications When you make the connection successfully the LED on the charger turns solid red indicating charging has begun Charging a fully discharged not over discharged 30mAh battery takes approximately 15 20minut
2. If charging or discharging discontinue and disconnect Continuing to use charge or discharge a battery that is ballooning or swelling can result in fire Always store the battery at room temperature in a dry area for best results Always transport or temporarily store the battery in a temperature range of 40 120 F 5 49 C Do not store the battery or model ina car or direct sunlight If stored in a hot car the battery can be damaged or even catch fire Always charge batteries away from flammable materials e Always inspect the battery before charging e Always disconnect the battery after charging and let the charger cool between charges e Always constantly monitor the temperature of the battery pack while charging ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI PO BATTERIES Failure to charge the battery with a compatible charger may cause a fire resulting in personal injury and or property damage e Never discharge Li Po cells to below 3V under load Never cover warning labels with hook and loop strips e Never leave charging batteries unattended e Never charge batteries outside recommended levels e Never charge damaged batteries Never attempt to dismantle or alter the charger e Never allow minors to charge battery packs e Never charge batteries in extremely hot or cold places recommended between 40 120 F or 5 49 C or place in direct sunlight Low Voltage Cutoff LVC When
3. Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please visit our website atwww horizonhobby com submit a Product Support Inquiry or call 877 504 0233 toll free to speak to a Product Support representative Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content _ service center_render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you will be asked to provide your complete name street addre
4. a Li Po battery is discharged below 3V per cell it will not hold a charge The aircraft s ESC protects the flight battery from over discharge using Low Voltage Cutoff LVC Before the battery charge decreases too much LVC removes power supplied to the motor Power to the motor quickly decreases and increases showing that some battery power is reserved for flight control and safe landing When the motor power pulses land the aircraft immediately and recharge the flight battery Disconnect and remove the Li Po battery from the aircraft after use to prevent trickle discharge Fully charge your Li Po battery before storing it During storage make sure the battery charge does not fall below 3V per cell For your first flights set your transmitter timer or a stopwatch to 5 minutes Adjust your timer for longer or shorter flights once you have flown the model Flights of 6 minutes or more are achievable if using proper throttle management NOTICE Repeated flying to LVC will damage the battery RTF Macy Installing Transmitter Batteries Your ParkZone 4 channel DSM2 DSMX RTF transmitter comes pre bound to the aircraft Remove the cover install four of the included batteries noting proper polarity and reinstall the cover BNF Eig Transmitter and Receiver Binding Binding is the process of programming the receiver of the control unit to recognize the GUID Globally Unique Identifier code of a single sp
5. flight Elevator 100 70 It is normal for linear servos to make noise Noise is Rudder 100 70 not an indication of a faulty servo To achieve the proper Low Rate settings when using a programmable DSM aircraft transmitter set the low rate value to 70 for elevator and rudder Adjusting Center of Gravity CG The CG location is 60mm back from the leading Balance the model on the edge of a metal ruler to edge of the center of the wing find the Center of Gravity Place the ruler on the underside side of the airframe This CG location has been determined with the included 1S 30mAh 3 7V Li Po battery installed in the battery holder Motor Service A CAUTION DO NOT handle propeller parts while the flight battery is connected Personal Remove injury could result dre Disassembly 1 Disconnect the battery from the ESC receiver 2 Hold the spur gear and turn the propeller counterclockwise looking from the front of the model to remove Turn the propeller clockwise to install Make sure the propeller size numbers 125 x 39 face away from the motor see illustration 3 Hold the nut on the end of the prop shaft using needle nose pliers or hemostats 4 Turn the gear on the shaft clockwise looking from front of model to remove the nut 5 Gently pull the shaft A from the gearbox B and make sure the washer C and two bushings D are no
6. rudder Pull back gently with the elevator and climb to check trim Once the trim is adjusted begin exploring the flight envelope of the Mini Vapor Flying After takeoff the Mini Vapor will climb at 3 4 to full throttle The Mini Vapor is designed for a slow and relaxing flight experience Fly at a slow controlled speed appropriate for the size of the location Landing Fly the aircraft to approximately 6 inches 15cm or less above the landing surface Reduce the throttle and the Mini Vapor should glide in softly for a landing NOTICE Failure to lower the throttle stick and trim to the lowest possible positions during a crash could result in damage to the ESC in the receiver unit which may require replacement NOTICE Crash damage is not covered under warranty A INTEN decrease throttle at propeller strike Repairs Repair the Mini Vapor using clear tape When parts are not repairable see the Replacement Parts List for ordering by item number For a listing of all replacement and optional parts refer to the list atthe back of this manual Additional Safety Precautions and Warnings As the user of this product you are solely responsible for operating it in a manner that does not endanger yourself and others or result in damage to the product or the property of others e Always keep a safe distance in all directions around your model to avoid collisions or injury This model is controlled by a ra
7. 100 ristian Junge Stra Germany Horizon Hobby GmbH 55335 do Germany eee avion e nedtonede PONT France Horizon Hobby SAS Matin infofrance horizon 91230 Montgeron hobby com 86 021 5180 9868 China Horizon Hobby Room 506 No 97 Changshou China Rd Shanghai China 200060 ata com cn 73 2012 Horizon Hobby Inc ParkZone E flite Vapor DSM DSM2 Bind N Fly and ModelMatch are trademarks or registered trademarks of Horizon Hobby Inc DSMX is a trademark of Horizon Hobby Inc registered in the U S The Spektrum trademark is used with permission of Bachmann Industries Inc Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan US D578 146 PRC ZL 200720069025 2 US 7 898 130 Other patents pending ku parkzone www parkzone com PKZU1200 PKZU1280 Created 06 12 36880
8. 2 3 K RX ESC m 2 3 voies DSMX RX Rx ESC a 3 canali servos Servos Vario 2 servos con 2 servo PKZU1236 Super Lite servo Super Lite Servo M canique de Meccaniche del mechanics Mechanik servo Super Lite servo Super Lite Fuselage with Rumpf mit Fuselage avec Fusoliera con PKZU1261 electronics Mini Elektronik Mini lectronique Mini elettronica Mini Vapor Vapor Vapor Vapor Bare Rumpf ohne Fuselage nu Mini Fusoliera nuda PKZU1267 Fuselage Mini Elektronik Mini Vapor Mini Vapor Vapor Vapor Replacement Ersatzrumpf Structure de Cellula di ricambio airframe without Tragflache remplacement senza elettronica PKZU1270 electronics Mini Leitwerk o sans lectronique Mini Vapor Vapor Elektronik Mini Mini Vapor Vapor PKZU1216 6mm Brushed 6mm Moteur a balais Motore a spazzole Motor Burstenmotor diam 6mm da 6mm Gear Box without Getriebe o Motor R ducteur sans Cambio senza PKZU1227 motor Mini Mini Vapor moteur Mini motore Mini Vapor Vapor Vapor Prop Shaft Mini Propellerwelle Arbre d h lice Albero dell elica PKZU1228 Vapor Mini Vapor Mini Vapor Mini Vapor Tail Skid Mini Hecksporn Mini B quille de queue Carrello di coda PKZU1207 Vapor Vapor Mini Vapor Mini Vapor 72 Optional Parts and Accessories e Optionale Bauteile und Zubeh r e Pi ces et accessoires optionnels e Componenti e accessori opzionali Part Nummer Num ro Codice EFLC1005 AU EU UK Description AC to 6V DC 1
9. 4 Recharge the flight battery 5 Store the flight battery apart from the aircraft and monitor the battery charge 6 Make note of the flight conditions and flight plan results planning for future flights Troubleshooting Guide Problem Aircraft will not respond to throttle but re sponds to other controls Possible Cause Throttle stick and or throttle trim is too high Solution Reset controls with throttle stick and throttle trim at lowest setting Throttle channel is reversed Reverse throttle channel on transmitter Extra propeller noise or extra Damaged propeller prop shaft or motor Replace damaged parts Nut on prop shaft is too loose Tighten the prop shaft nut 1 2 turn vibration Reduced flight Flight battery charge is low Completely recharge flight battery time or aircraft propeller is installed backward Install propeller with numbers faci underpowered ropeller is installed backwards nstall propeller with numbers facing forward Flight battery is damaged Replace flight battery and follow flight battery instructions Flight conditions may be too cold Make sure battery is warm before use Battery capacity is too low for flight conditions Replace battery or use a larger capacity battery LED on receiver flashes rapidly and aircraft will not bind to transmitter during binding Transmitter is too near aircraft during binding proce
10. 5 amp Power Supply Based upon your sales Region Beschreibung AC zu 6V DC 1 5 Ampere Netz stecker Basierend nach Vertriebsregion Description Alimentation CA vers 6 V CC 1 5 A En fonction de votre r gion Descrizione Alimentatore da CA a 6 V CC 1 5 Amp in base al Paese di vendita DX4e DSMX Spektrum DX4e Emetteur DX4e DX4e DSMX 4 channel DSMX 4 DSMX 4 voies Trasmettitore 4 Transmitter Kanalsender canali ohne Empfanger DX5e DSMX Spektrum DX5e Emetteur DX5e DX5e DSMX 5 channel DSMX 5 Ka DSMX 5 voies Trasmettitore 5 Transmitter nalsender canali ohne Empfanger DX6i DSMX DX6i DSMX Emetteur DX6i DX6i DSMX 6 Channel Trans 6 Kanal DSMX 6 voies Trasmettitore 6 mitter Sender canali DX7s DSMX Spektrum DX7s Emetteur DX7s DX7s DSMX 7 Channel 7 Kanal Sender DSMX 7 voies Trasmettitore 7 Transmitter canali DX8 DSMX Spektrum DX8 nur Emetteur DX8 DX8 DSMX Solo Transmitter Sender DSMX 8 voies trasmettitore Parts Contact Information e Kontaktinformationen fiir Ersatzteile Coordonn es pi ces Recapiti dei distributori Country of Purchase Horizon Hobby Address none NUDE 4105 Fieldstone Rd 800 338 4639 United States Sales Champaign Illinois 61822 sales horizonhobby USA com Units 1 4 Ployters Rd 44 0 1279 641 097 United Kinadom Horizon Hobby Staple Tye i 9 Limited Harlow Essex sales horizonhobby CM18 7NS United Kingdom co uk uu da 49 0 4121 2655
11. D EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice 146589 fpaizone WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of purchase cannot provide warranty support or service
12. FLY Includes BNF BIND N FLY Table of Contents Charging the Battery EEN Charging WarningsS Installing Transmitter Batteries Transmitter and Receiver Binding Installing the Flight Battery and Arming the ESC 7 Preflight Checklist EEN 7 Digital Tris 8 Dual Rate FUNCtION eesesseessesssessecssesssesseeseesseeseeeses 8 Transmitter Control Control Direction Test 9 Adjusting Center of Gravity CG 11 Motor Service o Flying Tips and Repairs i Additional Safety Precautions and Warnings 14 Post Flight Checklist Troubleshooting Guide E Limited Warranty Warranty and Service Information 18 FCC Information Compliance Information for the European Union19 Reverse COntrols sementer Replacement Parts EE 72 Control Centering Optional Parts and ACCESSOTiEeS 73 Settings for Control Voms en 10 Parts Contact Information scssssssssissststseiee 73 Control Rates 11 Specifications 87in 220mm A I 11 8 in 299mm 9 31 oz 8 7 9 RTF READY TO FLY Installed Installed Ac Installed Installed Included Included EG Included Included Needed to VIII Included Complete a BNF BIND N FLY 6mm Brushed Motor Super Lite DSMX RX ESC Servos PKZU1252 Battery 30mAh 3 7 25C Li Po Charger 1S 3 7V Li Po Battery Charger gt _
13. G parkzone Ultra Micro Mini Vapor Instruction Manual Bedienungsanleitung Manuel d utilisation Manuale di Istruzioni BIND N FLY SPEKTRUM DSM TECHNOLOGY READY TO FLY NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit www horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury A WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this Pr
14. What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Horizon Hobby authorized service center v Product not purchased from an authorized Horizon dealer or vi Product not compliant with applicable technical regulations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be that Horizon will at its option either i service or ii replace any Product determined by Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement decisions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AN
15. dio signal subject to interference from many sources outside your control Interference can cause momentary loss of control e Always operate your model in open spaces away from full size vehicles traffic and people e Always carefully follow the directions and warnings for this and any optional support equipment chargers rechargeable battery packs etc Always keep all chemicals small parts and anything electrical out ofthe reach of children e Always avoid water exposure to all equipment not specifically designed and protected for this purpose Moisture causes damage to electronics Never place any portion of the model in your mouth as it could cause serious injury or even death Never operate your model with low transmitter batteries Always keep the aircraft in sight and under control Always use fully charged batteries Always keep the transmitter powered ON while the aircraft is powered Always remove batteries before disassembly Always keep moving parts clean Always keep parts dry Always let parts cool after use before touching Always remove batteries after use Always ensure failsafe is properly set before flying Never operate aircraft with damaged wiring Never touch moving parts Post Flight Checklist 1 Disconnect the flight battery from the ESC Required for safety and battery life 2 Power OFF the transmitter 3 Remove the flight battery from the aircraft
16. e or repair damaged parts and adjust controls Wire damaged or connections loose Do a check of wires and connections connect or replace as needed Flight battery charge is low Fully recharge flight battery Control linkage does not move freely Make sure control linkage moves freely e Aparkzone D i Troubleshooting Guide continued Problem Possible Cause Solution Controls Transmitter settings reversed Do the Control Direction Test and adjust reversed controls on transmitter appropriately Motor loses Damage to motor or power components Do a check of motor and power compo power nents for damage replace as needed Nut on prop shaft is too tight Loosen prop shaft nut until propeller shaft turns freely Motor power quickly decreas es and increases then motor loses power Battery power is down to the point of receiver ESC Low Voltage Cutoff LVC Recharge flight battery or replace battery that is no longer performing Servo locks or Travel adjust value is set above 100 Set Travel adjust to 100 or less and or freezes at full overdriving the servo set sub trims to Zero and adjust linkages travel mechanically Limited Warranty What this Warranty Covers Horizon Hobby Inc Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in materials and workmanship at the date of purchase
17. ecific transmitter You need to bind your chosen Spektrum DSM technology equipped aircraft transmitter to the receiver for proper operation For a list of compatible DSM2 DSMX transmitters please visit www bindnfly com A CAUTION When using a Futaba transmitter with a Spektrum DSM module you must reverse the throttle channel and rebind Refer to your Spektrum module manual for binding and failsafe instructions Refer to your Futaba transmitter manual for instructions on reversing the throttle channel v Binding Procedure Reference Table 1 Refer to your transmitter s unique instructions for binding to a receiver Make sure the flight battery is disconnected from the aircraft 2 3 Ensure the transmitter is powered OFF 4 Connect the flight battery to the aircraft The receiver LED will begin to flash typically after 5 seconds Put your transmitter into bind mode If you are using the transmitter that is supplied with the RTF version push the left control stick vertically into the case until it clicks while powering ON the transmitter Make sure the transmitter controls are at neutral and the throttle is in the low position After 5 to 10 seconds the receiver status LED will become solid indicating that the receiver is bound to the transmitter If the LED does not turn solid refer to the Troubleshooting Guide at the end of the manual For subsequent fl
18. es As the battery nears full charge the LED begins to blink The intervals between blinks will increase as the battery comes closer to full charge When the LED blinks approximately every 20 seconds the battery is ready to be removed However the battery can be left charging until the LED completely goes out for a maximum charge A CAUTION Once charging is complete immediately remove the battery Never leave a battery connected to the charger Purchase the optional AC to 6V DC 1 5 amp Power Supply EFLC1005 to charge your battery pack without AA batteries A CAUTION Only use an E flite 6V power supply EFLC1005 with this charger DO NOT use a 12V power supply or property damage and injury could occur CHARGING Solid Red READY Blinking 20 sec intervals MAX CHARGE off If the LED stays ON when the flight battery is removed the AA batteries in the charger are low Ai Rapa et t st t t lt i stists S Charging Warnings The Battery Charger EFLC1002 included with your aircraft has been designed to safely charge the Li Po battery A CAUTION All instructions and warnings must be followed exactly Mishandling of Li Po batteries can result in a fire personal injury and or property damage By handling charging or using the included Li Po battery you assume all risks associated with lithium batteries e If at any time the battery begins to balloon or swell discontinue use immediately
19. first flights or in the event of an accident make sure the flight control surfaces are centered Adjust the linkages mechanically if the control surfaces are not centered Use of the transmitter trims may not correctly center the aircraft control surfaces due to the mechanical limits of linear servos 1 Make sure the control surfaces are neutral when the transmitter controls and trims are NOTICE When using a programmable transmitter centered The transmitter sub trim must be do not use Sub Trim to adjust the center position set to zero of the servo 2 When needed use a pair of pliers to carefully NOTICE Never set Travel Adjust above 100 Ultra bend the metal of the linkage see illustration Micro servos are unique in that they are calibrated 3 Make the U shape narrower to make the to reach maximum travel at 100 travel adjust connector shorter Make the U shape wider Increasing the value above 100 will NOT result to make the linkage longer in more travel but can cause the servo to lock and will result in a crash Settings for Control Horns Rudder Elevator The illustration shows factory settings for linkages on the control horns After flying if you want to modify control throw carefully adjust the linkage positions for desired control response Control Rates We recommend using a DSM2 DSMX aircraft High Rat count transmitter capable of dual rates Adjust according to individual preferences after initial
20. hina Changshou Rd info horizonhobby com cn Shanghai China 200060 e FCC Information This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation A CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This product contains a radio transmitter with wireless technology that has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2 400GHz to 2 4835GHz frequency range Compliance Information for the European Union Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2012070801 Product s PKZ Mini Vapor BNF Item Number s PKZU1280 Equipment class 1 The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European R amp TTE directive 1999 5 EC EMC Directive 2004 108 EC and LVD Directive 2006 95 EC EN 301 489 1 V1 7 1 2006 EN 301 489 17 V1 3 2 2008 EN 60950 1 2006 A12 2011 EN55022 2010 EN55024 2010 CE Signed for and on behalf of Horizon Hobby Inc Champaign IL USA July 08 2012 Eee SO WLL Steven A Hall Execut
21. ights power on the transmitter for 5 seconds before connecting the flight battery Installing the Flight Battery and Arming the ESC Arming the ESC also occurs after binding as previously described but subsequent connection of a flight battery requires the following steps A CAUTION Always keep hands away from propeller When armed the motor will turn the propeller in response to any throttle movement A CAUTION Always disconnect the Li Po battery from the aircraft receiver when not flying to avoid over discharging the battery Batteries discharged to a voltage lower than the lowest approved voltage may become damaged resulting in loss of performance and potential fire when batteries are charged Lower throttle and throttle trim to lowest settings Power ON the Trans mitter then wait 5 seconds Secure the battery to the hook and loop strip on the battery holder Connect the battery to the ESC noting proper polarity T caiilindous LED i Preflight Checklist 1 Charge the flight battery 2 Install the flight battery in the aircraft once it has been fully charged 3 Bind the aircraft to the transmitter BNF only 4 Make sure the linkages move freely Perform the Control Direction Test with the transmitter Adjust the center of gravity Find a safe and open area Plan flight appropriate for flying location RTF b s Be T
22. ive VP Chief Operating Officer International Operations and Risk Management Horizon Hobby Inc in accordance with ISO IEC 17050 1 No HH2012070802 Product s PKZ Mini Vapor RTF Item Number s PKZU1200 Equipment class 1 The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European R amp TTE directive 1999 5 EC EMC Directive 2004 108 EC and LVD Directive 2006 95 EC EN 300 328 V1 7 1 2006 EN 301 489 1 V1 7 1 2006 EN 301 489 17 V1 3 2 2008 EN 60950 1 2006 A12 2011 EN55022 2010 EN55024 2010 CE Signed for and on behalf of Horizon Hobby Inc OD VAL Champaign IL USA Steven A Hall July 08 2012 Executive VP Chief Operating Officer International Operations and Risk Management Horizon Hobby Inc Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural WE resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling p
23. lease contact your local city office your household waste disposal service or where you purchased the product Replacement Parts Ersatzteile Pi ces de rechange e Pezzi di ricambio Part 8 Nummer Num ro Codice Description Beschreibung Description Descrizione PKZU1202 Prop 125 x 39 Propeller 125 x 39 H lice indoor Elica Elica per indoor propeller Indoor Propeller 125 x 39 interni 125 x 39 PKZU1220 Wing Mini Vapor Tragflache Mini Aile de Mini Vapor Ala Mini Vapor Vapor Landing Gear Fahrgestellsatz Jeu de train Set carrello di PKZU1206 Mini Vapor Mini Vapor d atterrissage atterraggio Mini Mini Vapor Vapor Pushrod Set Mini Schubstangensatz Jeu de biellettes Set asta di spinta PKZU1222 Vapor Mini Vapor m caniques Mini Mini Vapor Vapor Horizontal stab HOhenruder Mini Stabilisateur Mini Stabilizzatore PKZU1224 Mini Vapor Vapor Vapor orizzontale Mini Vapor PKZU1225 Rudder Mini Seitenruder Mini D rive Mini Vapor Timone Mini Vapor Vapor Vapor 15 3 7V 25C 15 3 7 V 25C Batterie Li Po Batteria Li Po EFLB0301525 30mAh Li Po 30 mAh Li Po Akku 30 mAh 25C 1S da 3 7 V 25C Battery 3 7V 1S 30 mAh EFLC1002 AC DC 3 7V Li Po AC DC3 7V Li Po Chargeur AC DC Caricabatterie Charger Ladeger t Li Po 3 7V Li Po CA CC 3 7 V Super Lite DSMX Super Lite DSMX Module Super Lite Super Lite DSMX PKZU1252 3 Ch rx esc w
24. oduct in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not attempt disassembly use with incompatible components or augment product in any way without the approval of Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy Welcome to an exciting new world of flying possibilities Bedrooms conference rooms garages basements break rooms offices all can be transformed into aerial RC playgrounds with the Ultra Micro Series Mini Vapor Its small size negligible mass and proportional 3 channel control will let you confidently fly almost anywhere indoors without worrying about damage to it or the furniture Before you start exploring your new found flying opportunities however you must take some time to read this manual It contains important information about some of the aircraft s wind limitations DSM2 DSMX technology battery charging and much more You ll also find a handy troubleshooting guide It s all here to make sure your first flight and every one after is the best it can be Box Contents RTF READY TO
25. oney orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and Conditions found on our website http www horizonhobby com content _service center_render service center NOTICE Horizon service is limited to Product compliant in the country of use and ownership If non compliant product is received by Horizon for service it will be returned unserviced at the sole expense of the purchaser Warranty and Service Information country of Horizon Hobby Address Phone Number Email Address Horizon Service 4105 Fieldstone Rd 877 504 0233 Center Electronics Champaign Illinois Online Repair Request visit United States and engines 61822 USA www horizonhobby com service of America Horizon Product 4105 Fieldstone Rd 877 504 0233 Support All other Champaign Illinois productsupport horizonhobby products 61822 USA com Units 1 4 Ployters Rd United Horizon Hobby Staple he 44 0 1279 641 097 Kingdom Limited CM18 7NS United sales horizonhobby co uk Kingdom Ceman Horizon Christian Junge StraBe 1 49 0 4121 2655 100 y Technischer Service 25337 Elmshorn Germany service horizonhobby de 14 Rue Gustave Eiffel Zone d Activit du 33 0 160 47 44 70 France Horizon Hobby SAS R veil Matin infofrance horizonhobby com 91230 Montgeron Horizon Hobby _ Room 506 No 97 486 021 5180 9868 China C
26. r beginner pilots or others interested in smoother and more easily controlled flight Control Direction Test Bind your aircraft and transmitter before doing these tests Move the controls on the transmitter to make sure aircraft control surfaces move correctly Always keep throttle at the low position during testing Down Elevator Z N L NS Lo 4 Ai k Up Elevator RRS I d Se if gt Left Rudder Right Rudder Reverse Controls NOTICE The Mini Vapor RTF should not require any servo reversing Should the Mini Vapor electronic components be used in another aircraft you may find it necessary to reverse the operation of the flight control surfaces Rudder Reversed Rudder Normal Elevator Reversed Elevator Normal The transmitter included with the Mini Vapor isthe 4 Hold the digital trim buttons down for same transmitter included in other ParkZone Ultra approximately 5 seconds until you hear a Micro RTF models tone confirming the selection 1 Ensure the battery is disconnected from 5 Connect the flight battery and complete the aircraft and the transmitter is turned OFF the flight control test Confirm all surfaces 2 Press and hold the digital trim button for operate in the correct direction the surface you would like to reverse 3 While holding the digital trim button turn the transmitter ON Control Centering Before
27. ransmitter Control Throttle Elevator Rudder Throttle Rudder a CDer Rudder Trim Throttle Trim Digital Trims The Bark Zone 4 channel DSM2 DSMX transmitter features digital trim buttons on all controls to make fine adjustments The digital trims are used to fine tune the model s flight path when in flight Before the first flight center the control surfaces mechanically see Control Centering When pressed down trim buttons make a sound that increases or decreases in pitch at each pressing The middle or neutral trim position is heard as a middle tone in the pitch range of the sounds The end of the control range is sounded by a series of beeps Dual Rate Function This transmitter s dual rate feature lets you change between high and low control rates for the elevator and rudder When powered ON this transmitter is automatically set to high rate mode Change rate modes by pushing the right hand control stick vertically into the case until it clicks while the transmitter is powered on High rate mode is shown by the transmitter s LED glowing solid red In high rate mode the controls can reach their maximum values This mode is typically preferred by experienced pilots for maximum control authority Low rate mode is shown by the transmitter s LED blinking continuously In low rate mode the controls are reduced to approximately 70 of their maximum values This mode is typically preferred by and best fo
28. ss Power off transmitter move transmitter a larger distance from aircraft disconnect and reconnect flight battery to aircraft and follow binding instructions Bind switch or button was not held while transmitter was powered on Power off transmitter and repeat bind process Aircraft or transmitter is too close to large metal object wireless source or another transmitter Move aircraft and transmitter to another location and attempt binding again LED on receiver flashes rapidly and aircraft will not respond to transmitter after binding Less than a 5 second wait between first powering on transmitter and connect ing flight battery to aircraft Leaving transmitter on disconnect and reconnect flight battery to aircraft Aircraft is bound to a different model memory ModelMatch radios only Select correct model memory on trans mitter and disconnect and reconnect flight battery to aircraft Flight battery transmitter battery charge is too low Replace recharge batteries Transmitter may have been bound to a different model or with a different DSM Protocol Select the right transmitter or bind to the new one Aircraft or transmitter is too close to large metal object wireless source or another transmitter Move aircraft and transmitter to another location and attempt linking again Control surface does not move Control surface control horn linkage or servo damage Replac
29. ss email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of hour of labor In addition you will be billed for return freight Horizon accepts m
30. t lost 6 Disconnect the motor from the ESC receiver 7 Gently push the motor out of the gearbox and remove the motor NOTICE DO NOT remove the gearbox from the aircraft Damage to the aircraft will result Assembly Assemble the aircraft using the instructions above in reverse order e Correctly align the prop shaft gear with the pinion gear on the motor Correctly connect the motor to the ESC receiver so that the powered motor turns the propeller clockwise looking from the front of the model Flying Tips and Repairs We recommend flying your Mini Vapor in an indoor location with a floor area of 15 ft x 15 ft and a minimum ceiling height of 8 ft a living room or office is ideal We suggest first flights take place in a larger area like a garage or basement We do not recommend flying the Mini Vapor outdoors unless the conditions are absolutely calm The Mini Vapor is extremely light and can be easily blown away Hand Launching Hold the Mini Vapor at shoulder height with one hand While holding your transmitter in your other hand increase the throttle to half Launch the Mini Vapor using light force Keep the wings level and do not throw it up or down Point it level with the ground when releasing Do not grasp the pushrods while launching as this may result in damage to the servos Runway Takeoff Place the Mini Vapor in position for takeoff Gradually increase the throttle to full and steer with the

ParkZone Mini Vapor RTF

Contents

Download Pdf Manuals

Related Search

Related Contents