Kramer Electronics TP-114
Contents
1. please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILLPAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated in2. which are connected via RJ 45 connectors make sure that the shield of the STP cable is connected to the metal casing of the connectors on both ends of the cable For units which are connected via terminal block connectors the shield of the STP cable must be connected to a ground terminal on the units at both ends use the ground terminal of the power supply connection if necessary For a CAT 5 cable exceeding a distance of 50m separate power supplies should be connected to the transmitter and to the receiver simultaneously 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP We recommend that you use Shielded Twisted Pair STP cable There are different levels of STP cable available and we advise you to use the best quality STP cable that you can afford Our non skew free cable Kramer BC STP is intended for analog signals where skewing is not an issue For 1 The terminology XGA is used throughout this manual where this implies any RGBHV signal on an 15 pin HD connector having a resolution from VGA up to UXGA 2 The TP 114 accepts high definition resolutions 480p 576p 720p 1080i and 1080p 3 Note that the CAT 5 connectors exclude audio 4 CAT 5 cable is still suitable for the video audio transmission but not for feeding the power at these distances 3 Overview 3 3 cases where there is skewing our UTP skew free cable Kramer BC XTP may be used Bear in mind though that we advise using STP cables where pos
3. 1 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and lightindustry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and lightindustry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION B Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment BD Usethe supplied DC power supply to feed power to the machine ED Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products 10 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution P N 2900 000183 Rev 2 Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000183 REV 2
4. Kramer Electronics Ltd USER MANUAL Model TP 114 1 4 XGA HD DA CAT 5 Transmitter Contents Contents 1 Introduction 2 Getting Started 2 1 Getting Started 3 Overview 3 1 About the Power Connect Feature 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP 3 3 Recommendations for Achieving the Best Performance 4 Your TP 114 1 4 XGA HD DA CAT 5 Transmitter 5 Configuring a TP 114 XGA HD Line Transmitter DA System 5 1 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors 6 Technical Specifications Figures Figure 1 TP 114 1 4 XGA HD DA CAT 5 Transmitter Figure 2 TP 114 1 4 XGA HD DA CAT 5 Transmitter Underside Panel Figure 3 Configuring a TP 114 XGA HD Line Transmitter DA Figure 4 CAT 5 PINOUT Tables Table 1 TP 114 1 4 XGA HD DA CAT 5 Transmitter Features Table 2 TP 114 1 4 XGA HD DA CAT 5 Transmitter Underside Panel Features Table 3 CAT 5 PINOUT Table 4 Technical Specifications of the TP 114 with 100m CAT 5 cable CON NM FWWW NY oo oa WW OOo Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear
5. T RJ 45 connector see section 5 1 2 By default both switches are set down for negative V SYNC and H SYNC polarity 3 Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level 4 By default both switches are set down to NORMAL to retain the VS and HS polarity 7 Configuring a TP 114 XGA HD Line Transmitter DA System Long CAT 5 cable Computer Graphics Source Long CAT 5 cable Display 4 Figure 3 Configuring a TP 114 XGA HD Line Transmitter DA KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 5 1 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors Table 3 and Figure 4 define the UTP CAT 5 PINOUT using a straight pin to pin cable with RJ 45 connectors Table 3 CAT 5 PINOUT Figure 4 CAT 5 PINOUT EIA TIA 568A EIA TIA 568B PIN Wire Color PIN Wire Color 1 Green White 1 Orange White 2 Green 2 Orange 3 Orange White 3 Green White 4 Blue 4 Blue 5 Blue White 5 Blue White 6 Orange 6 Green 7 Brown White T Brown White 8 Brown 8 Brown Te Pair 1 4 and 5 Pair 1 4and5 Pair2 3and6 Pair 2 1and2 Pair3 1 and2 Pair 3 3 and 6 Pair4 7and8 Pair4 7ands ee 6 Technical Specifications Table 4 includes the technical specifications of the TP 114 Table 4 Technical Specifications ofthe TP 114 with 100m CAT 5 cable INPUT 1 XGA on an 15 p
6. graphics source to the XGA input The XGA output to a local display Up to 4 of the line outputs to the line inputs for example on TP 120 XGA Line Receivers via UTP cabling Long CAT 5 cable zu Si S Long CAT 5 cable j mm Step 2 Connect the power Computer Graphics Source Display Step 3 Change the polarity see section 5 You can change the polarity of decoding H and V Sync for video see Figure 4 and Table 2 NEGATIVE v Gus NORMAL KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 Overview Your Kramer TOOLS TP 114 1 4 XGA HD DA CAT 5 Transmitter is a high performance distribution amplifier for computer graphics video or HDTV signals It converts a computer graphics video or HDTV signal on a 15 pin HD connector to four identical twisted pair signals The TP 114 e Receives a computer graphics HD signal and transmits it over four CAT 5 cables to appropriate receivers e Has a resolution of up to UXGA and a transmission range of more than 300 feet more than 100 meters e Can change the polarity of decoding H and V Sync for video e Includes the Power Connect feature e Is powered by 12V DC 3 1 About the Power Connect Feature The Power Connect feature applies as long as the cable can carry power This feature is available when using STP cable and the distance does not exceed 50m on standard CAT 5 cable For longer distances heavy gauge cable should be used For units
7. in 11 groups that are clearly defined by function Thank you for purchasing the Kramer TOOLS TP 114 XGA HD Line Transmitter DA which is ideal for e Presentation and multimedia applications e Long range graphics distribution for schools hospitals security and stores The package includes the following e TP 114 1 4 XGA HD DA CAT 5 Transmitter e Power supply 12V DC e This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 Download up to date Kramer user manuals from our Web site at http www kramerelectronics com 3 The complete list of Kramer cables is on our Web site at http www kramerelectronics com 1 Getting Started 2 1 Getting Started This quick start chart summarizes the basic setup and operation steps Step 1 Connect the inputs and outputs see section 5 On the TP 114 connect A computer
8. in HD connector OUTPUTS 1 XGA on an 15 pin HD connector 4 RJ 45 OUT connectors MAX OUTPUT LEVEL 1 8Vpp XGA 1 6Vpp CAT 5 MAX RESOLUTION UXGA 1080P DIFF GAIN 0 03 XGA 7 CAT 5 DIFF PHASE 0 05 XGA 0 08 CAT 5 K FACTOR lt 0 05 XGA 0 3 CAT 5 S N RATIO 75dB XGA 73dB CAT 5 CONTROLS 2 switches for sync inversion COUPLING DC XGA AC CAT 5 POWER SOURCE 12V DC 880mA DIMENSIONS 12cm x 7 15cm x 2 76cm 4 7 x 2 8 x 1 08 W D H WEIGHT 0 3kg 0 67Ibs approx ACCESSORIES Power supply OPTIONS RK 3T 19 rack adapter 1 Specifications are subject to change without notice 2 For the TP 114 Transmitter TP 120 Receiver pair 3 Sufficient for feeding two receivers via CAT 5 LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOWLONGISTHE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOISPROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized
9. pin HD connector and connect the line output RJ 45 connector OUT 1 connector to the LINE IN RJ 45 connector on the first TP 120 OUT 2 connector to the LINE IN RJ 45 connector on the second TP 120 OUT 3 connector to the LINE IN RJ 45 connector on the third TP 120 OUT 4 connector to the LINE IN RJ 45 connector on the fourth TP 120 2 On the four TP 120 units connect the XGA OUT 15 pin HD connector of the first TP 120 unit to the XGA HD acceptor for example display 1 XGA OUT 15 pin HD connector of the second TP 120 unit to the XGA HD acceptor for example display 2 XGA OUT 15 pin HD connector of the third TP 120 unit to the XGA HD acceptor for example display 3 XGA OUT 15 pin HD connector of the fourth TP 120 unit to the XGA HD acceptor for example display 4 3 Oneach Kramer TOOL connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity The signal from the XGA source is transmitted via the CAT 5 cables decoded and converted at the each of the XGA OUT 15 pin HD connectors to the XGA acceptors 4 On the TP 120 units if necessary Set the H SYNC and V SYNC switches on the underside Adjust the video output signal level and or cable compensation equalization level 5 On the TP 114 if necessary set the VS and HS switches on the underside 1 Via UTP cabling with a range of more than 300ft gt 100m For details of how to wire a CAT 5 LINE IN LINE OU
10. re 3 Configuring a TP 114 XGA HD Line Transmitter DA System Figure 2 and Table 2 define the TP 114 underside panel NEGATIVE ve Bis NORMAL Figure 2 TP 114 1 4 XGA HD DA CAT 5 Transmitter Underside Panel Table 2 TP 114 1 4 XGA HD DA CAT 5 Transmitter Underside Panel Features Feature Function 1 VS Switch Slide the switch up to change the VS polarity to NEGATIVE polarity slide the switch down to NORMAL to retain the polarity 2 HS Switch Slide the switch up to change the HS polarity to NEGATIVE polarity slide the switch down to NORMAL to retain the polarity System Configuring a TP 114 XGA HD Line Transmitter DA You can use the TP 114 with four TP 120 units to configure a 1 4 XGA HD DA CAT 5 Transmitter system This will let you transmit a computer graphics HD signal to four displays via long line CAT 5 UTP cabling To connect the TP 114 to four TP 120 units as the example in Figure 3 illustrates do the following 1 By default both switches are set in the down position 2 Downgoing syncs 3 Refer to the separate user manual PT 110 PT 120 TP 120 WP 110 which can be downloaded from the Internet at http www kramerelectronics com KRAMER SIMPLE CREATIVE TECHNOLOGY Configuring a TP 114 XGA HD Line Transmitter DA System 1 On the TP 114 connect the XGA HD source for example a computer graphics HD source to the XGA IN 15
11. sible since the compliance to electromagnetic interference was tested using those cables Although Unshielded Twisted Pair UTP cable might be preferred for long range applications the UTP cable should be installed far away from electric cables motors and so on which are prone to create electrical interference However since the use of UTP cable might cause inconformity to electromagnetic standards Kramer does not commit to meeting the standard with UTP cable Recommendations for Achieving the Best Performance To achieve the best performance e Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances that may adversely influence signal quality and position your Kramer TP 114 away from moisture excessive sunlight and dust H No operator serviceable parts inside unit Warning M Use only the Kramer Electronics input power wall Warne ee that is provided with the unit Warning Disconnect power and unplug unit from wall before installing or removing the device or servicing unit 1 Available from Kramer Electronics on our Web site at http www kramerelectronics com KRAMER SIMPLE CREATIVE TECHNOLOGY Your TP 114 1 4 XGA HD DA CAT 5 Transmitter 4 Your TP 114 1 4 XGA HD DA CAT 5 Transmitter Figure 1 and Table 1 define
12. the TP 114 KRAMER TOOLS 1 4 XGA HD DAYCATS Transmitter EEE Lo Pi 5 4 f i LJ 4 LJ Ne LINE OUT1 LINE OUT2 LINE OUT3 LINE OUT 4 TP 114 XGA IN XGA OUT d bd Figure 1 TP 114 1 4 XGA HD DA CAT 5 Transmitter Table 1 TP 114 1 4 XGA HD DA CAT 5 Transmitter Features Feature Function 1 LINE OUT 1 RJ 45 Connector Connects to the LINE IN RJ 45 connector on the first TP 120 XGA Line Receiver 2 LINE OUT2 RJ 45 Connector Connects to the LINE IN RJ 45 connector on the second TP 120 XGA Line Receiver 3 LINE OUT 3 RJ 45 Connector Connects to the LINE IN RJ 45 connector on the third TP 120 XGA Line Receiver 4 LINE OUT 4 RJ 45 Connector Connects to the LINE IN RJ 45 connector on the fourth TP 120 XGA Line Receiver 12V DC 12V DC connector for powering the unit XGA IN 15 pin HD Connector Connect to the XGA source XGA OUT 15 pin HD Connector Connect to the XGA acceptor N o ON LED llluminates when receiving power 1 Using a UTP CAT 5 cable with RJ 45 connectors at both ends the PINOUT is defined in Table 3 and Figure 4 2 Refer to the separate user manual PT 110 PT 120 TP 120 WP 110 which can be downloaded from the Internet at http www kramerelectronics com Also see the example illustrated in Figu
13. voice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 5008
Download Pdf Manuals
Related Search