Foster S3000.Domino.IS.2
Contents
1. Do not use any extension cable to connect it The appliance can not be used above a dishwasher or a tumble dryer steam may damage the electronic appliances Using the appliance Switch the heating zones off after using Keep an eye on the cooking using grease or oils that may quickly ignite Be careful not to burn yourself while or after using the appliance Make sure no cable of any fixed or moving appliance contacts with the glass or the hot saucepan Magnetically objects credit cards floppy disks calculators should not be placed near to the engaged appliance Do not place any metallic object except heating containers In case of untimely engaging or residual heat this one may heat melt or even burn Never cover the appliance with a cloth or a protection sheet This is supposed to become very hot and catch fire This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Metallic objects such as knives forks spoons and lids should not be placed on the hob surface since they can get hot Precautions not to damage the appliance Raw pan bottoms or damaged saucepans not enamelled cast iron pots may damage the cera2. or 1 9 To select Timer Press key C 00 minutes Decrease the time Press key 30 to 29 28 27 Increase the time Press key The time increases After a few seconds the control light stops with blinking The time is confirmed and the cooking starts e To stop the cooking time Action Control panel Display To select Timer Press key The remaining time To stop the Timer Press key then D Displays 00 then stops If they are several timer activated you must repeat this operation e Automatic stop at the end of the cooking time As soon as the selected cooking time is finished the timer displays blinking 00 and a sound rings and the heating zone stops To stop the sound and the blinking it is enough to press key 7 e Egg timer function Action Control panel Display Activate the hob Press key 0 1 The zone control lights are on To select Timer Press key C 00 minutes Decrease the time Press key 30 to 29 28 27 Increase the time Press key The time increases After a few seconds the control light stops with blinking and the timer starts e To stop the egg timer function Action Control panel Display Activate the hob Press key 0 1 Timer light blinking To stop the Timer Press key then C Displays 00 then stops Control panel locking To avoid modifying a setting of cooking zones in particular with w
3. compatible with induction e The bottom diameter of the pan is too small The symbol C or E displays e Call the After sales Service One or all cooking zones cut off The safety system functioned You forgot to cut off the cooking zone for a long time One or more sensitive keys are covered The pan is empty and its bottom overheated The hob also has an automatic reduction of power level and breaking Automatic overheating Continuous ventilation after cutting off the hob e This is not a failure the fan continuous to protect the electronic device e The fan cooling stops automatically 11 MAINTENANCE AND CLEANING Switch off the appliance before cleaning Do not clean the hob if the glass is too hot risk of burn Remove light marks with a damp cloth with cleaning liquid diluted in a little water Then rinse with cold water and dry the surface thoroughly Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be absolutely avoided Do not ever use any steam driven or pressure appliance Do not use any object that may scratch the ceramic glass Ensure that the pan is dry and clean Ensure that there are no grains of dust on your ceramic hob or on the pan Sliding rough saucepans will scratch the surface Spillages of sugar jam jelly etc must be removed immediately You will thus prevent the surface being damaged ENVIRONMENT PROTECTION The packaging material is ecolo
4. ieri 7 BOOSTER FUNCTION vevsiehc ceil ete eased Ae Ae td 7 TIMER fia OOM o otek ohh e le do ee as eR PS ud an ni 8 CONTROL PANEL LOCKING iii 9 COOKING ADVIGES A A AA A earn 9 PANIQUALITY E EE S IVA it es tie tials 9 PAN DIMENSION L e e ae a ne 9 EXAMPLES OF POWER SETTING ci 10 WHAT TO DO IN CASE OF A PROBLEM sss sss nente neeaaea eae aaee 10 MAINTENANCE AND CLEANING lt lt sss ss sss sss esea eena enean enean aaeeea eee 12 ENVIRONMENT PROTECTION sss ss cs seene eee 12 INSTALLATION INSTRUCTIONS scs s lt c c csoc eaea 13 ELECTRICAL CONNECTION sss sss ss sss sese e eena ennenen eaea ane eaea eaea eaea 14 SAFETY Precautions before using Unpack all the materials The installation and connecting of the appliance have to be done by approved specialists The manufacturer can not be responsible for damage caused by building in or connecting errors To be used the appliance must be well equipped and installed in a kitchen unit and an adapted and approved work surface This domestic appliance is exclusively for the cooking of food to the exclusion of any other domestic commercial or industrial use Remove all labels and self adhesives from the ceramic glass Do not change or alter the appliance The cooking plate can not be used as freestanding or as working surface The appliance must be grounded and connected conforming to local standards
5. level Selection of the cooking level U Pan Detection No pan or inadequate pan E Error message Electronic failure H Residual heat The heating zone is hot P Booster The boosted power is activated Ventilation The cooling system is fully automatic The cooling fan starts with a low speed when the calories brought out by the electronic system reach a certain level The ventilation starts his high speed when the hob is intensively used The cooling fan reduces his speed and stops automatically when the electronic circuit is cooled enough STARTING UP AND APPLIANCE MANAGEMENT Before the first use Clean your hob with a damp cloth and then dry the surface thoroughly Do not use detergent which risks causing blue tinted colour on the glass surface Induction principle An induction coil is located under each heating zone When it is engaged it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan The result is a heating up of the pan located on the heating zone Of course the pan has to be adapted e All ferromagnetic pans are recommended please verify it thanks a little magnet cast iron and steel pans enamelled pans stainless steel pans with ferromagnetic bottoms e Are excluded cupper pure stainless steel aluminium glass wood ceramic stoneware The induction heating zone adapts automatically the size of the pan With a too small diameter the pan doesn t
6. or d e f 7321240 keys Start from left to right A double beep sound will inform you of a bad manipulation and you will have to restart from OBEO OgHo a b C d e T _ N357 WD AZ 3 The left display shows alternatively a C anda 0 OHO G G 4 Press the key lock until both displays indicate either C or 5 Take your fingers away from the keys and press again the key during a few seconds until some E appear 6 You will hear a beep sound and the E will blink 7 The E are automatically transformed into C The configuration has been canceled VI How to configure the hob 1 Use a suitable induction pot with a minimum diametre size of 16cm 2 Select the heating zone by pushing the corresponding key 3 Put the pot on the corresponding heating zone 4 Wait until C converts to The zone is configured 5 Use the same procedure for each other heating zone which displays C 6 The configuration is made if all zones are detected and if nothing is displayed Use only 1 pot to configure the hob Never put two or more pots on the heating zones during the configuration If E 4 display persists call the After sales Service The hob or the cooking zone doesn t start up The hob is badly connected on the electrical network The protection fuse cut off The locking function is activated The sensitive keys are covered of grease or water An object is put on a key 23 The
7. setting The values below are indicative 1 to2 Melting Sauces butter chocolate gelatine Reheating Dishes prepared beforehand 2t03 Simmering Rice pudding sugar syrop Defrosting Dried vegetables fish frozen products 3 to 4 Steam Vegetables fish meat 4 t05 Water Steamed potatoes soups pasta fresh vegetables 6 to7 Medium cooking Meat liver eggs sausages Simmering Goulash roulade tripe 7 to8 Cooking Potatoes fritters wafers 9 Frying rosting Steaks omelettes fried dishes Boiling water Water P Boiling water Boiling significant quantities of water WHAT TO DO IN CASE OF A PROBLEM The symbol E 4 displays e The hob must be configured according to the following procedure I Warning before starting all pots must be removed from the cooktop Il Disconnect the cooktop from the main supply remove fuse or disconnect circuit breaker III Connect the cooktop to the main supply replace the fuse or connect the circuit breaker IV Procedure You must provide yourself with a ferromagnetic bottom container 16 cm minimum diametre start within 2 minutes after the connection to the main supply do not use the O I key V How to cancel the existing configuration 1 Push on the locking key and keep your finger on the key Oddo OBE0o 2 With a finger from the other hand activate successively and quickly a b c keys Start from left to right A double beep
8. symbol U displays e There is no pan on the cooking zone e The pan is not compatible with induction e The bottom diameter of the pan is too small The symbol C or E displays e Call the After sales Service One or all cooking zones cut off The safety system functioned You forgot to cut off the cooking zone for a long time One or more sensitive keys are covered The pan is empty and its bottom overheated The hob also has an automatic reduction of power level and breaking Automatic overheating Continuous ventilation after cutting off the hob e This is not a failure the fan continuous to protect the electronic device e The fan cooling stops automatically MAINTENANCE AND CLEANING Switch off the appliance before cleaning Do not clean the hob if the glass is too hot risk of burn e Remove light marks with a damp cloth with washing up liquid diluted in a little water Then rinse with cold water and dry the surface thoroughly e Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be absolutely avoided e Do not ever use any steam driven or pressure appliance e Do not use any object that may scratch the ceramic glass e Ensure that the pan is dry and clean Ensure that there are no grains of dust on your ceramic hob or on the pan Sliding rough saucepans will scratch the surface e Spillages of sugar jam jelly etc must be removed immediately You will thus prevent the sur
9. the cooking zone Examples of power setting The values below are indicative 1 to2 Melting Sauces butter chocolate gelatine Reheating Dishes prepared beforehand 2 to3 Simmering Rice pudding sugar syrop Defrosting Dried vegetables fish frozen products 3 to 4 Steam Vegetables fish meat 4to5 Water Steamed potatoes soups pasta fresh vegetables 6 to7 Medium cooking Meat lever eggs sausages Simmering Goulash roulade tripe 7 to 8 Cooking Potatoes fritters wafers 9 Frying rosting Steaks omelettes fried dishes Boiling water Water P Boiling water Boiling significant quantities of water WHAT TO DO IN CASE OF A PROBLEM The symbol E 4 displays The hob must be configured according to the following procedure I Warning before starting all pots must be removed from the cooktop Il Disconnect the cooktop from the main supply remove fuse or disconnect circuit breaker III Connect the cooktop to the main supply replace the fuse or connect the circuit breaker IV Procedure You must provide yourself with a ferromagnetic bottom container 16 cm minimum diametre start within 2 minutes after the connection to the main supply do not use the O I key V How to cancel the existing configuration 1 Push on the locking key and keep your finger on the key Oddo OBE0o 2 With a finger from the other hand activate successively and quickly a b c 7322240
10. Foster a Live the Quality USER S MANUAL FOR INDUCTION HOBS cod 7322 230 Dear client Thank you for having chosen our induction ceramic hob In order to make the best use of your appliance we would advise you to read carefully the following notes and to keep them for a later consulting SUMMARY SABE DY ON 16 PRECAUTIONS BEFORE USING ci 16 USING THE APPEIANGE dite Sees ee eile eee Be ee ee ae eh ee ee 16 PRECAUTIONS NOT TO DAMAGE THE APPLIANCE 2 ecceceececeececcecceeeseceeaeeaececeececeeaeeaecueeesaseeueeeeas 17 PRECAUTIONS IN CASE OF APPLIANCE FAILURE ii 17 OTHER PROTECTIONS e 6 cece T A es Le AR AREA AE 17 DESCRIPTION OF THE APPLIANCE s ss xsesrensenaee nese zen e ezine ne nie iene ienzieni 18 TECHNICAL DATA ist ariani TT 18 CONTROL PANEL 18 USER Rana ni aaa ot 18 SENSITIVE TOUCHE Seve ari ela ape sede weet tart le de ale oh ae 18 DISPEAV sce a Beetle anton cet 108 deliri te Sl ole asia ire a o alia irene io 19 NENTILATION EE tebe i RR 19 STARTING UP AND APPLIANCE MANAGEMENT 2 2cceeceecceeceeccneececcescneceeceneceeceeseneeeees 19 BEFORE THEIFIRS RUSE Z Z wierd ei oe dd se diodi eo en 19 INDUGTION PRINGCIPLE e A en eo os 19 STARTING SUP 2 Ae Pe ett eset ent Art AAA Ih a ek Re 19 PAN DETEGRION L A A E AA 20 RESIDUAL HEAT INDICATION 20 BOOSTER FUNCION E 2d e sd nad bee heed ee ene 20 TIMER 2220s 2 oe conta tate a watt ee
11. aminate coatings and the glue used to fix them must be able to resist temperatures of up to 100 C The mural rods of edge must be heat resisting Materials which are often used in the manufacturing of worktops tend to expand on contact with water To protect the cut out edge apply a coat of varnish or special sealant Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces Do not install the hob to the top of a not ventilated oven or a dishwasher Please make sure that a space of of 20 mm is left under the appliance in order to ensure a good air circulation of air for the electronic device If a drawer is placed under the work avoid to put into this drawer flammable objects for example sprays or not heat resistant objects The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer In case of absence of instructions respect a distance minimum of 760 mm The connection cord should be subjected after building with no mechanical constraint such for example of the fact of the drawer 13 ELECTRICAL CONNECTION e The installation of this appliance and the connection to the electrical network should be entrusted only to a professionally trained and authorized eletrician and performed in full respect of al
12. bility of electric shock Other protections Make sure that the container pan is always centred on the cooking zone The bottom of the pan must have to cover as much as possible the cooking zone For the users of pacemaker the magnetic field could influence its operating We recommend to request necessary information before using the appliance both tot he vendor and one s Doctor Do not to use aluminium or synthetic material containers they could melt on still hot cooking zones DO NOT USE INTERMEDIATE REMOVABLE ACCESSORIES TO HEAT PANS WHICH ARE NOT ADAPTED TO INDUCTION RISKS OF BURNS AND DETERIORATION OF THE HOB DESCRIPTION OF THE APPLIANCE Technical data Type Total Power Position Nominal Power Booster Power Diameter Front 1200W 1400W 150 mm Rear 2000W 2300W 220 mm The given power may change according to the dimensions and material of the pan 7322230 3700W Control panel Control light timer Locking ke i i Timer Power display mi fan Le a USE Sensitive touches Your ceramic hob is equipped with electronic controls with sensitive touch keys When your finger touches the key the corresponding command is activated This activation is validated by a control light a letter or a number in the display and or a beep sound Touch only one key on the same time Display Display Designation Function 0 Zero The heating zone is activated 1 9 Power
13. elect Timer Press key O 00 minutes Decrease the time Press key 30 to 29 28 27 Increase the time Press key The time increases After a few seconds the control light stops with blinking The time is confirmed and the cooking starts e To stop the cooking time Action Control panel Display To select Timer Press key The remaining time To stop the Timer Press key then Displays 00 then stops If there are several timers activated you must repeat this operation e Automatic stop at the end of the cooking time As soon as the selected cooking time is finished the timer displays blinking 00 and a sound rings and the heating zone stops To stop the sound and the blinking it is enough to press key e Egg timer function Action Control panel Display Activate the hob Press key 0 1 zone control lights are on To select Timer Press key O 00 minutes Decrease the time Press key 30 to 29 28 27 Increase the time Press key The time increases After a few seconds the control light stops with blinking and the timer starts e To stop the egg timer function Action Control panel Display Activate the hob Press key 0 1 Timer light blinking To stop the Timer Press key then O Displays 00 then stops Control panel locking To avoid modifying a setting of cooking zones in particular with within the framework of cleani
14. ete ae dn eS hoy ed del re ei e oi dica liu 21 CONTROL PANEL LOCKING ii 21 COOKING ADVICES cinc cian 22 PANQUAL Va da td Dd ad ado A E A ALI e ad de AET 22 PANDIMENSION a e ae es ia es ie ee 22 EXAMPLES OF POWER SETTING e e ci 22 WHAT TO DO IN CASE OF A PROBLEM neon eine 23 MAINTENANCE AND CLEANING lt lt sss ss sss sss seene aenean eenn neee aaeeea aaee 24 ENVIRONMENT PROTECTION 00 2 cscceeceeccneceeccneececeeccneceeccusceceaseueceeceeaseeceasensceesensenssenseneees 24 INSTALLATION INSTRUCTIONS scs s c c c csoc eaea anean aeaee nane eee eee iii iene 25 ELECTRICAL CONNECTION sss sss sss sese e eena eanne eaea eean 26 15 SAFETY Precautions before using Unpack all the materials The installation and connecting of the appliance have to be done by approved specialists The manufacturer can not be responsible for damage caused by building in or connecting errors To be used the appliance must be well equipped and installed in a kitchen unit and an adapted and approved work surface This domestic appliance is exclusively for the cooking of food to the exclusion of any other domestic commercial or industrial use Remove all labels and self adhesives from the ceramic glass Do not change or alter the appliance The cooking plate can not be used as freestanding or as working surface The appliance must be grounded and connected conforming to local standards Do
15. face being damaged ENVIRONMENT PROTECTION e The packaging material is ecological and can be recycled e The worn appliances contain certain noble metals Apply to the local government about the possibilities of recycling e Don t throw your appliance with the household refuses Get in touch with the waste collection center of your commune that is adapted to the recycling of the household appliances 24 INSTALLATION INSTRUCTIONS The installation comes under the exclusive responsibility of specialists The installer is held to respect the legislation and the standards enforce in his home country How to stick the gasket The gasket supplied with the hob avoids all infiltration of liquids in the cabinet His installation has to be done carefully in conformity of the following drawing Stick the gasket 2 two millimeters from the external edge of the glass after removing the protection sheet 3 Fitting installing The cut out sizes are Appliance Cut out 7321240 360 x 490 mm 7322240 360 x 490 mm Ensure that there is a distance of 50 mm between the hob and the wall or sides The hobs are classified as Y class for heat protection Ideally the hob should be installed with plenty of space on either side There may be a wall at the rear and tall units or a wall at one side On the other side however no unit or divider must stand higher than the hob T
16. gical and can be recycled The worn appliances contain certain noble metals Apply to the local government about the possibilities of recycling e Don t throw your appliance with the household refuses Get in touch with the waste collection center of your commune that is adapted to the recycling of the household appliances 12 INSTALLATION INSTRUCTIONS The installation comes under the exclusive responsibility of specialists The installer is held to respect the legislation and the standards enforce in his home country How to stick the gasket The gasket supplied with the hob avoids all infiltration of liquids in the cabinet His installation has to be done carefully in conformity of the following drawing Stick the gasket 2 two millimeters from the external edge of the glass after removing the protection sheet 3 Fitting installing The cut out sizes are Appliance Cut out 7322230 270 x 500 mm Ensure that there is a distance of 50 mm between the hob and the wall or sides The hobs are classified as Y class for heat protection Ideally the hob should be installed with plenty of space on either side There may be a wall at the rear and tall units or a wall at one side On the other side however no unit or divider must stand higher than the hob The piece of furniture or the support in which the hob is to be fitted as well as the edges of furniture the l
17. he piece of furniture or the support in which the hob is to be fitted as well as the edges of furniture the laminate coatings and the glue used to fix them must be able to resist temperatures of up to 100 C The mural rods of edge must be heat resisting Materials which are often used to make worktops expand on contact with water To protect the cut out edge apply a coat of varnish or special sealant Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces Not to install the hob to the top of a not ventilated oven or a dishwasher To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air circulation of the electronic device If a drawer is placed under the work avoid to put into this drawer flammable objects for example sprays or not heat resistant objects The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer In case of absence of instructions respect a distance minimum of 760 mm The connection cord should be subjected after building with no mechanical constraint such for example of the fact of the drawer 25 ELECTRICAL CONNECTION e The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly
18. ility of electric shock Other protections Note sure that the container pan is always centred on the cooking zone The bottom of the pan must have to cover as much as possible the cooking zone For the users of pacemaker the magnetic field could influence its operating We recommend getting information to the retailer or of the doctor Do not to use aluminium or synthetic material containers they could melt on still hot cooking zones DO NOT USE INTERMEDIATE REMOVABLE ACCESSORIES TO HEAT PANS WHICH ARE NOT ADAPTED TO INDUCTION RISKS OF BURNS AND DETERIORATION OF THE HOB 17 DESCRIPTION OF THE APPLIANCE Technical data Type Total Power Position Nominal Power Booster Power Diameter 7321240 3000W Front 2300W 3000W 250 mm Front left 1200W 1400W 160 mm El 200 Rear right 2300W 3000W 200 mm The given power may change according to the dimensions and material of the pan Control panel Control light timer key On Off USE Sensitive touches Your ceramic hob is equipped with electronic controls with sensitive touch keys When your finger touches the key the corresponding command is activated This activation is validated by a control light a letter or a number in the display and or a beep sound Touch only one key on the same time 18 Display Display Designation Function 0 Zero The heating zone is activated 1 9 Power level Selection of the co
19. ithin the framework of cleaning the control panel can be locked with exception to the On Off key 0 1 e Locking Action Control panel Display Start Press key 0 1 0 or H on displays Hob locking Press key 0 or H on displays Locking light is on e Unlocking Action Control panel Display Start Press key 0 1 0 on displays Unlocking the hob Press key k 0 on displays Locking light is off 21 COOKING ADVICES Pan quality Adapted materials steel enamelled steel cast iron ferromagnetic stainless steel aluminium with ferromagnetic bottom Not adapted materials aluminium and stainless steel without ferromagnetic bottom cupper brass glass ceramic porcelain The manufacturers specify if their products are compatible induction To check if pans are compatibles e Puta littler water in a pan placed on an induction heating zone set at level 9 This water must heat in a few seconds e A magnet stuck on the bottom of the pan Some pans can make noise when they are placed on an induction cooking zone This noise doesn t mean any failure on the appliance and doesn t influence the cooking operating Pan dimension The cooking zones are until a certain limit automatically adapted to the diameter of the pan However the bottom of this pan must have a minimum of diameter according to the corresponding cooking zone To obtain the best efficiency of your hob please place the pan well in the center of
20. l Servizio Assistenza 39 0522 684450 fax 39 0522 686019 fax Servizio Ricambi 39 0522 962166 e mail service fosterspa com www fosterspa com 13846 3 cod 9606886
21. l enforced regulations e Protection against the parts under tension must be ensured after the building in e The data of connection necessary are on the stickers place on the hob casing near the connection box e The connection to the main must be made using an earthed plug or via an omnipolar circuit breaking device with a contact opening of at least 3 mm e The electrical circuit must be separated from the network by adapted devices for example circuit breakers fuses or contactors Caution This appliance has only to be connected to a network 230 V 50 60 Hz Connect always the earth wire Respect the connection diagram Use the connecting cable that is attached to the device The green yellow wire correspond to the earth wire the blue wire correspond neutral wire and the brown wire correspond to the phase Mains Connection Cable diameter Cable Protection calibre x 2 HO5VV F Z 230V 50 60Hz 1 Phase N 3 x 1 5 mm HOSRR F 16 A calculated with the simultaneous factor following standard EN 60 335 2 6 1990 Caution Ensure that you correctly attach the wires and the bridges and tighten the screws properly We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been equipped with a faulty earth connection 14 Foster spa 42041 Brescello RE Italy tel 39 0522 687425 te
22. mic glass Sand or other abrasive materials may damage ceramic glass Avoid dropping objects even little ones on the vitroceramic Make sure that the ventilation of the appliance works according to the manufacturer s instructions Do not hit the edges of the glass with saucepans Do not put or leave empty saucepans on the vitroceramic hobs Sugar synthetic materials or aluminium sheets must not contact with the heating zones These may cause breaks or other alterations of the vitroceramic glass by cooling switch on the appliance and take them immediately out of the hot heating zone be careful do not burn yourself Never place any hot container over the control panel If a drawer is situated under the embedded appliance make sure the space between the content of the drawer and the inferior part of the appliance is large enough 2cm This is essential to guaranty a correct ventilation Never put any inflammable object ex sprays into the drawer situated under the vitroceramic hob The eventual cutlery drawers must be resistant to heat Precautions in case of appliance failure If a defect is noticed switch off the appliance and turn off the electrical supplying If the ceramic glass is cracked or fissured you must unplug the appliance and contact the after sales service Repairing has to be done by specialists Do not open the appliance by yourself WARNING If the surface is cracked switch off the appliance to avoid the possi
23. mic glass Sand or other abrasive materials may damage ceramic glass Avoid dropping objects even little ones on the vitroceramic Make sure that the ventilation of the appliance works according to the manufacturer s instructions Do not hit the edges of the glass with saucepans Do not put or leave empty saucepans on the vitroceramic hobs Sugar synthetic materials or aluminium sheets must not contact with the heating zones These may cause breaks or other alterations of the vitroceramic glass by cooling switch on the appliance and take them immediately out of the hot heating zone be careful do not burn yourself Never place any hot container over the control panel If a drawer is situated under the embedded appliance make sure the space between the content of the drawer and the inferior part of the appliance is large enough 2cm This is essential to guaranty a correct ventilation Never put any inflammable object ex sprays into the drawer situated under the vitroceramic hob The eventual cutlery drawers must be resistant to heat Precautions in case of appliance failure If a defect is noticed switch on the appliance and turn off the electrical supplying If the ceramic glass is cracked or fissured you must unplug the appliance and contact the after sales service Repairing has to be done by specialists Do not open the appliance by yourself WARNING If the surface is cracked switch off the appliance to avoid the possib
24. ng the control panel can be locked with exception to the On Off key 0 I e Locking Action Control panel Display Start Press key 0 1 0 or H on displays Hob locking Press key 6J 0 or H on displays Locking light is on e Unlocking Action Control panel Display Start Press key 0 1 0 on displays Unlocking the hob Press key G 0 on displays Locking light is off COOKING ADVICES Pan quality Adapted materials steel enamelled steel cast iron ferromagnetic stainless steel aluminium with ferromagnetic bottom Not adapted materials aluminium and stainless steel without ferromagnetic bottom cupper brass glass ceramic porcelain The manufacturers specify if their products are compatible induction To check if pans are compatibles e Puta littler water in a pan placed on an induction heating zone set at level 9 This water must heat in a few seconds e A magnet stuck on the bottom of the pan Some pans can make noise when they are placed on an induction cooking zone This noise doesn t mean any failure on the appliance and doesn t influence the cooking operating Pan dimension The cooking zones are until a certain limit automatically adapted to the diameter of the pan However the bottom of this pan must have a minimum of diameter according to the corresponding cooking zone To obtain the best efficiency of your hob please place the pan well in the center of the cooking zone Examples of power
25. not use any extension cable to connect it The appliance can not be used above a dishwasher or a tumble dryer steam may damage the electronic appliances Using the appliance Switch the heating zones off after using Keep an eye on the cooking using grease or oils that may quickly ignite Be careful not to burn yourself while or after using the appliance Make sure no cable of any fixed or moving appliance contacts with the glass or the hot saucepan Magnetically objects credit cards floppy disks calculators should not be placed near to the engaged appliance Do not place any metallic object except heating containers In case of untimely engaging or residual heat this one may heat melt or even burn Never cover the appliance with a cloth or a protection sheet This is supposed to become very hot and catch fire This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Metallic objects such as knives forks spoons and lids should not be placed on the hob surface since they can get hot 16 Precautions not to damage the appliance Raw pan bottoms or damaged saucepans not enamelled cast iron pots may damage the cera
26. oking level U Pan Detection No pan or inadequate pan E Error message Electronic failure H Residual heat The heating zone is hot P Booster The boosted power is activated Ventilation The cooling system is fully automatic The cooling fan starts with a low speed when the calories brought out by the electronic system reach a certain level The ventilation starts his high speed when the hob is intensively used The cooling fan reduces his speed and stops automatically when the electronic circuit is cooled enough STARTING UP AND APPLIANCE MANAGEMENT Before the first use Clean your hob with a damp cloth and then dry the surface thoroughly Do not use detergent which risks causing blue tinted colour on the glass surface Induction principle An induction coil is located under each heating zone When it is engaged it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan The result is a heating up of the pan located on the heating zone Of course the pan has to be adapted e All ferromagnetic pans are recommended please verify it thanks a little magnet cast iron and steel pans enamelled pans stainless steel pans with ferromagnetic bottoms e Are excluded cupper pure stainless steel aluminium glass wood ceramic stoneware The induction heating zone adapts automatically the size of the pan With a too small diameter the pan doesn t work This diameter is var
27. sound will inform you of a bad manipulation and you will have to restart from point 1 GORR 0 G G a b 10 3 The left display shows alternatively a C anda 0 OHO GBR G 4 Press the key lock until both displays indicate either C or 5 Take your fingers away from the keys and press again the key during a few seconds until some E appear 6 You will hear a beep sound and the E will blink 7 The E are automatically transformed into C The configuration has been canceled VI How to configure the hob 1 Use a suitable induction pot with a minimum diametre size of 16cm 2 Select the heating zone by pushing the corresponding key 3 Put the pot on the corresponding heating zone 4 Wait until C converts to The zone is configured 5 Use the same procedure for each other heating zone which displays C 6 The configuration is made if all zones are detected and if nothing is displayed Use only 1 pot to configure the hob Never put two or more pots on the heating zones during the configuration e If E 4 display persists call the After sales Service The hob or the cooking zone doesn t start up e The hob is badly connected on the electrical network e The protection fuse cut off e The locking function is activated e The sensitive keys are covered of grease or water e An object is put on a key The symbol U displays e There is no pan on the cooking zone e The pan is not
28. spa 42041 Brescello RE Italy tel 39 0522 687425 tel Servizio Assistenza 39 0522 684450 fax 39 0522 686019 fax Servizio Ricambi 39 0522 962166 e mail service fosterspa com www fosterspa com 13848 3 cod 9606885 Dear client Thank you for having chosen our induction ceramic hob In order to make the best use of your appliance we would advise you to read carefully the following notes and to keep them for a later consulting SUMMARY SAFE stesa A I 3 PRECAUTIONS BEFORE USING ici 3 UsSING THE APPLIANCE iaia ie aa 3 PRECAUTIONS NOT TO DAMAGE THE APPLIANCE i 4 PRECAUTIONS IN CASE OF APPLIANCE FAILURE iii 4 OTHER PROTEC TONS lt 230 Si eat Shae De e ea Os 4 DESCRIPTION OF THE APPLIANCE 0 20 0 ccscceecceccneceeccnececeeccneceeccneceeceaseneceeseeeceeseesenseeesensenees 5 TECHNICAL DATA sti s ee ten A eee ee ean ea tes ee A a fa e i a 5 CONTROLE PANEL Aslan ceeds het cay eck Bete sete reheat on ce esc Aledo tated dl ek dde senora 5 USE leer pe faenza ll iaia 5 SENSITIVE TOUGHE Snia aL elia 5 DISPIAY Lido iii ia NS E E e i A IIa 6 AAS SO IN AEA ie ie Ad 6 STARTING UP AND APPLIANCE MANAGEMENT sss css sss essea ennenen eaae 6 BEFORE THE FIRST USE a neia aie lt ntl eee alee a odas 6 INDUCTION PRINCIPLES necia t 6 STARTING ti id tr Set ren oun ni cen eid cee ane cect Tea 7 PAN DETECTION ii 7 RESIDUAL HEAT INDICATION lt A R A
29. t don t touch the heating zone and don t put any heat sensitive object on them There are risks of burn and fire Booster function The booster function P grants a boost of power to the selected heating zone If this function is activated the heating zones works during 10 minutes with an ultra high power The booster is foreseen for example to heat up rapidly big quantities of water Start up Stop the booster function Action Control panel Display Increase power Press key or 1 to 9 Start up the booster Press key P for 10 min Stop the booster Press key 9 e Power management The cooking hob is equipped with a power limiting system When the booster function is activated and not to exceed the maximum power the electronic system orders to reduce automatically the power level of an other heating zone The display is blinking on 9 during a few seconds and then shows the maximum of power allowed Heating zone selected The other heating zone example power level 9 P is displayed 9 goes to 7 or 8 depending the type of zone Timer The timer is able to be used simultaneous with all 2 heating zones and this with different time settings from 0 to 99 minutes for each heating zone e Setting and modification of the cooking time Action Control panel Display To select the heating zone Press key or 4 or 9 To select the power level Press key or alba A ES To s
30. the heating zone and don t put any heat sensitive object on them There are risks of burn and fire Booster function The booster function P grants a boost of power to the selected heating zone If this function is activated the heating zones works during 10 minutes with an ultra high power The booster is foreseen for example to heat up rapidely big quantities of water like nuddles cooking e Start up Stop the booster function Action Control panel Display Increase power Press key or 1 to 9 Start up the booster Press key P during 10 min Stop the booster Press key 9 e Power management The whole cooking hob is equipped by a maximum of power When the booster function isactivated and not to exceed the maximum power the electronic system orders to reduce automatically the power level of an other heating zone The display is blinking on 9 during a few seconds and then shows the maximum of power allowed 6 or 8 Heating zone selected The other heating zone example power level 9 P is displayed 9 goes to 7 or 8 depending the type of zone 20 Timer The timer is able to be used simultaneous with all 2 heating zones and this with different time settings from 0 to 99 minutes for each heating zone e Setting and modification of the cooking time Action Control panel Display To select the heating zone Press key or 4 or 9 To select the power level Press key
31. to the fact of the normative regulations and which respects them scrupulously e Protection against the parts under tension must be ensured after the building in e The data of connection necessary are on the stickers place on the hob casing near the connection box e The connection to the main must be made using an earthed plug or via an omnipolar circuit breaking device with a contact opening of at least 3 mm e The electrical circuit must be separated from the network by adapted devices for example circuit breakers fuses or contactors Caution This appliance has only to be connected to a network 230 V 50 60 Hz Connect always the earth wire Respect the connection diagram Use the connecting cable that is attached to the device The green yellow wire correspond to the earth wire the blue wire correspond neutral wire and the brown wire correspond to the phase Mains Connection Cable diameter Cable Protection calibre E 2 H05 VV E 230V 50 60Hz 1 Phase N 3 x 1 5 mm HO5RR F 16A calculated with the simultaneous factor following standard EN 60 335 2 6 1990 Caution Ensure that you correctly attach the wires and the bridges and tighten the screws properly We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been equipped with a faulty earth connection 26 Foster
32. work This diameter is varying in function of the heating zone diameter If the pan is not adapted to the induction hob the display will show U Starting up You must first start up the hob then the heating zone Start up switch off the hob Action Control panel Display To start Press key O I 2x 0 To stop Press key 0 1 nothing or H Start up switch off the heating zone Action Control panel Display Increase power Press key 4 to 9 Decrease power Press key 9 to 1 Stop Press simultaneous and O or H or press O or H If no setting are made in 20 seconds the hob return in waiting position Pan detection The pan detection ensures a perfect safety The induction doesn t work If there is no pan on the heating zone or if this pan is not adapted to the induction In this case it is impossible to increase the power and the display shows U This symbol disappears when a pan is put on the heating zone If the pan is removed from the heating zone the operation is stopped The display shows U The symbol U disappears when the pan is put back to the heating zone The cooking continues with the power level chosen before Residual heat indication After the switch off of the hob the heating zone is still hot and indicates H on the display The symbol H disappears when the heating zone may be touched without danger As far as the residual heat indicator is on ligh
33. ying in function of the heating zone diameter If the pan is not adapted to the induction hob the display will show U Starting up You must first start up the hob then the heating zone e Start up switch off the hob Action Control panel Display To start Press key 0 1 2x 0 To stop Press key 0 1 nothing or H 19 e Start up switch off the heating zone Action Control panel Display Increase power Press key 4 to 9 Decrease power Press key 9 to 1 Stop Press simultaneous and O or H or press 0 or H If no setting are made in 20 seconds the hob return in waiting position Pan detection The pan detection ensures a perfect safety The induction doesn t work e lf there is no pan on the heating zone or if this pan is not adapted to the induction In this case it is impossible to increase the power and the display shows U This symbol disappears when a pan is put on the heating zone e Ifthe pan is removed from the heating zone the operation is stopped The display shows U The symbol U disappears when the pan is put back to the heating zone The cooking continues with the power level chosen before Residual heat indication After the switch off of the hob the heating zone is still hot and indicates H on the display The symbol H disappears when the heating zone may be touched without danger As far as the residual heat indicator is on light don t touch
Download Pdf Manuals
Related Search