Foster 7316 000 hob
Contents
1. Position the cooker hob in the cut out Press it forcefully agianst the worktop Applying the sealant The picture indicates how the sealant must be applied along the entire edge CONNECTION TO THE MAINS ELECTRICITY The electrical connections must be carried out by qualified personnel only The electrical connection must be protected in accordance with the regulations in force The connectors are accessible when the wires cover is opened Prior to connecting the appliance verify that the voltage indicated on the rating plate complies with the mains voltage The rating plate of the glass ceramic hob is located on the underside The appliance operates at 220 240V AC or alternatively at 380 415 V 2N In the direct connection to the mains electricity an omnipolar switch with a contact gap of 3 mm suitably sized for the load and conforming to the regulations in force is positioned between the appliance and the power outlet The type of electrical connection must be chosen according to the available installation options for the electric current and overload safety switches To ensure protection against fire appliances of this kind can be installed between a taller cabinet on one side and a cabinet of equal height as the appliance on the other side For safety reasons electrical connection components and insulated parts must not be accessible If the model is not equipped with a plug mount a standardised plug on the p2. SPECIFICATIONS MODEL L 7316 000 Code 7316 000 Width 520 mm Worktop cut out size 500 mm Electrical connection 220 240 V or 380 415 V 2N 50 60 Hz Rated voltage 220 240 V 50 60 Hz Cooking zones mm W front left 140 1 200 rear centre 180 120 1 700 700 front right 140 1 200 Total power W 4 100 SPECIFICATIONS MODEL 1 7352 010 Code 7352 010 Width 520 mm Worktop cut out size 500 mm Electrical connection 220 240 V or 380 415 V 2N 50 60 Hz Rated voltage 220 240 V 50 60 Hz Cooking zones mm W front left 140 1 200 rear centre 180 1 800 front right 140 1 200 Total power W 4 200 TECHNICAL ASSISTANCE In the event of cooker hob malfunctions we recommend verifying that the plug is properly inserted in the socket If the cause of the malfunction is identified turn the appliance off do not tamper with it and contact the Technical Assistance Service The appliance comes with a warranty certificate enabling the user to benefit from the Technical Assistance Service The warranty certificate must be stored and duly filled in to be presented to the Technical Assistance Service whenever required together with a fiscally valid document issued by the dealer at the moment of purchase delivery note invoice tax receipt other and indicating the dealer s name delivery date and product identifi
3. circle All the indicators light up for an instant when the cooker hob is turned on The cooker hob is ready for use The cooker hob is equipped with electronic sensors that turn on if the relative surfaces are touched for at least 1 second A buzzer sounds every time the sensors turn on Do not place any objects on the sensor surface error signal Make sure that the sensor surface is always kept clean Touch the on off sensor A for at least 1 second The cooker hob activates and 0 appears on all the heat setting indicators B The subsequent operation must be effected within 20 seconds or the cooker hob will turn off If the cooker hob was turned on with the on off sensor A the desired cooking zone can be selected within the next 20 seconds e When pressing the sensor C for the desired cooking zone the corresponding display visualises heat setting O e Pressing sensors lt C or E allows for selecting heat settings 1 9 Pressing and holding sensors lt C or E automatically decreases or increases the heat settings This can also be done by touching the corresponding sensors individually and modifying the heat setting by a single level each time The settings can be adjusted only for the selected cooking zone The display will visualise the symbol 0 lt or H if the cooking zone was previously heated see paragraph relative to residual heat 19 Turning the
4. surface is broken or cracked If you notice any defects disconnect the appliance from the power supply immediately e In the event of malfunctions unplug the power cord and contact the Technical Assistance Service e Do not clean the appliance using steam cleaners or high pressure devices e The appliance is manufactured according to the safety standards in force however we do not recommend that the appliance be operated by persons with reduced physical motion or mental capabilities or by inexperienced or untrained persons The same advice applies to use of the appliance by minors This appliance is marked in conformity to the specifications of European Directive 200 96 EC regarding waste electrical and electronic equipment The relative symbol appearing on the product or packaging indicates that the product must not be treated as normal household waste but must be taken to an appropriate waste collection facility for the recycling of electrical and electronic equipment Proper disposal of the product helps to prevent potential negative effects on the environment and health that may otherwise arise For more detailed information on how to recycle this product please contact the relative municipal department local waste disposal service or the dealer from which the product was purchased Prior to first use Important warnings The glass ceramic surface must be cleaned with the aid of a damp sponge and dish soap Do no
5. Before every use of the hob wipe away any dust from the glass ceramic surface and clean any dirt on pot bases as it may scratch the cooking zone Fig 1 Warning do not use steel wool sponges or abrasive detergents that may scratch the surface Aggressive sprays or unsuitable detergents may also damage the surface Fig 1 and Fig 2 The signs on the hob surface may fade due to the use of aggressive detergents steel wool sponges or dirty pot bases Fig 2 Remove the smaller stains with a damp sponge then dry the pot thoroughly Fig 3 Water stains can be eliminated using a vinegar solution which however should not be used on the hob frame of some models as it may lose its lustre Do not use aggressive detergents or sprays to remove limescale Fig 3 Stubborn dirt can be removed using detergents specially formulated for glass ceramic surfaces Follow the suggestions of the detergent manufacturer Be careful not to leave any detergent residues on the surface as these may damage the glass ceramic surface Fig 3 Stubborn dirt or burnt dirt must be removed with the aid of a scraper Make sure that the plastic scraper handle does not come into contact with the hot cooker hob Fig 4 Be careful not to harm yourself when using the scraper Sugar or foodstuffs with high sugar content may cause permanent damage to the glass ceramic surface Fig 5 for this reason any sugar residues must be immediately removed from the gl
6. Foster a Live the Quality USER S MANUAL COOKER HOB VITROLINE HI LIGHT Dear customer Operating instructions Electrical connections Rating plate Protection against the risk of fire The built in glass ceramic cooker hob is intended for domestic use Our products are packaged using eco compatible materials that can be recycled disposed of or destroyed For this reason we have appropriately indicated the materials comprising the packaging Should the appliance no longer be needed dispose of it responsibly so as to not harm the environment Deliver it to a specialised waste disposal facility The operating instructions are intended for the consumer They describe the appliance and its operation The instructions refer to several types models of appliances and may therefore describe functions that your appliance does not possess Electrical connections must be carried out as outlined in the chapter Connection to the mains electricity and in compliance with the regulations in force Connection operations must be carried out by qualified personnel only The rating plate containing basic appliance data is located on the underside of the appliance The appliance may be installed adjacent to a taller cabinet on one side and next to a cabinet of equal height on the other side The manufacturer is committed to constantly improving the product For this reason the text and illustrations appearing in this manual may be
7. SPECIFY THE ERROR CODE ER36 Short circuit in the touch control temperature CONTACT THE AUTHORISED sensor TECHNICAL ASSISTANCE CENTRE SPECIFY THE ERROR CODE ER40 Touch control secondary voltage too low and CONTACT THE AUTHORISED primary circuit PTC temperature too high TECHNICAL ASSISTANCE CENTRE SPECIFY THE ERROR CODE 21 GLASS CERAMIC COOKER HOB MODEL L 7352 010 Control knobs The cooking zones are controlled by knobs that turn clockwise and are connected to an energy regulator The numbers 1 to 8 indicate the various heat settings 1 is the lowest heat setting and 8 the highest while 0 corresponds to the O offO mode The cooking zone controlled by each knob is visualised in the identification diagram adjacent to each knob A Control knob B Residual heat indicator C Cooking zone identification diagram D Cooking zone Residual heat indicator Each heating element is associated with a residual heat indicator that automatically turns on once the corresponding cooking zone has reached or exceeded a temperature of 50 C Once the cooking zone is turned off the relative light remains lit until the cooking zone cools down to below 50 C 22 COOKER HOB CLEANING AND MAINTENANCE Fig 5 The glass ceramic surface must be cleaned after every use as any remaining small stains will burn on the hot surface For ordinary maintenance purposes use special detergents that form a protective film against dirt
8. ass ceramic surface even if still hot using a scraper Fig 4 Any change in the colour of the glass ceramic surface does not influence the operation or stability of the surface itself The colour change arises from the use of copper or aluminium pots or food residues on the pot base and is very difficult to eliminate Warning all the above mentioned defects are of an aesthetical nature and do not directly influence the appliance s operation They cannot be solved by activating the warranty 23 COOKER HOB INSTALLATION Important warnings e Installation of the appliance and connection to the mains electricity must be carried out by qualified personnel only e The lining of the worktop walls must be suitably treated with adhesives capable of withstanding temperatures of 100 C if not the colour and shape of the lining may alter e The appliance must be fitted into the worktop on a cabinet at least 600 mm wide e After installing the hob the two support elements secured on the built in appliance must be freely accessible from underneath e All kitchen wall cabinets must be positioned so as to not hamper the user when operating the hob e The distance between the hob and cooker hood must comply with that indicated in the cooker hood installation instructions The minimum distance must be 700 mm e Solid wood frames can be placed on the worktop provided they are positioned at a suitable distance see picture e The minimum dis
9. b may cause the latter to break The effects may appear immediately or at a later stage If you notice any visible cracks disconnect the appliance from the power supply immediately e If sugar or foodstuffs with high sugar content fall on the hot cooker hob clean the surface immediately Suggestions on the use of pots Use high quality pots with a straight and stable base e Heat transmission improves if the diameter of the pot base matches that of the cooking zone and by placing the pot in the centre of the cooking zone e Follow the suggestions of the pot manufacturer when cooking in heat resistant glass pots or porcelain pots e Pressure cookers must be supervised until they reach the right pressure The cooking zone starts functioning at maximum power then after a while lower the heat setting using the appropriate sensor on the basis of the pot manufacturer s indications e Make sure that the pressure cooker and all other pots contain enough liquids during cooking as cooking with an empty pot causes overheating and damage to both the pot and cooking zone e Heat resistant glass pots with flat base may be used on the glass ceramic hob provided their diameter matches that of the cooking zone Pots with larger diameter may crack due to thermal tension e Follow the indications of the pot manufacturer when using special pots e When cooking with light coloured pots e g light coloured metal or pots with thick bases boiling point w
10. cation data Foster spa via M S Ottone 18 20 42041 Brescello RE Italy tel 39 0522 687425 tel Servizio Assistenza 39 0522 684450 fax 39 0522 686019 fax Servizio Ricambi 39 0522 962166 e mail service fosterspa com www fosterspa com 147
11. cooker hob is equipped with sensors to protect it against overheating If overheating occurs the cooking zones closest to the control panel turn off ERROR CODE ERROR DESCRIPTION SOLUTION EROS Continuous activation of the sensors Dry off the water and remove the CONTINUOUS BUTTONS for more than 10 seconds due to objects from the sensor surface If BUZZER the presence of objects or liquids on the glass the problem persists CONTACT THE in the touch control area AUTHORISED TECHNICAL ASSISTANCE CENTRE SPECIFY THE ERROR CODE ER20 Microcontroller memory malfunction CONTACT THE AUTHORISED TECHNICAL ASSISTANCE CENTRE SPECIFY THE ERROR CODE ER21 This message appears at the end of the control CONTACT THE AUTHORISED cycle that verifies potential overheating of the TECHNICAL ASSISTANCE CENTRE touch control compartment SPECIFY THE ERROR CODE U400 Secondary circuit voltage too high primary 1 CONTACT THE AUTHORISED circuit voltage gt 300 V The touch control TECHNICAL ASSISTANCE CENTRE turns off after 1 second and a continous buzzer SPECIFY THE ERROR CODE 2 Contact sounds This may be due to 1 excessive an electrician to inspect the electrical voltage supply 2 faulty connection of the circuit cooker hob to the mains electricity ER22 Control board malfunction relevant to the CONTACT THE AUTHORISED selection sensors or touch control supply TECHNICAL ASSISTANCE CENTRE voltage beyond the limits
12. cooking zonesoff Turning the cooker hob off Safety lock child safety device Residual heat indicator Engaging disengagin the dual circuit Time limit device Turning off the cooking zone before cooking is completed allows for saving energy by using the residual heat to complete cooking e The selected cooking zone must be activated e Press the on off sensor E to lower the heat setting to 0 and after 10 seconds the cooking zone will turn off Fast turning off e The selected cooking zone must be activated e The cooking zone turns off by simultaneously pressing sensors and C and E respectively The cooker hob can be turned off at any time through the on off sensor A Activating this safety lock prevents use of the hob or cooking zones The safety lock also functions as a child safety device Activating the safety lock e Turn off all the cooking zones heat setting O 0 e Press sensor A to turn on the cooker hob if turned off The 0 symbol lights up on all the displays e Simultaneously press sensors D and After the buzzer sounds press sensor again All the displays will visualise the symbol L which disappears after 20 seconds The safety lock child safety device is activated Deactivating the safety lock e Press sensor A to deactivate the safety lock All the displays will visualise the symbol L e Simultaneously press sensors D and After the buzz
13. er sounds press sensor again The safety lock child safety device is deactivated The glass ceramic hob is equipped with a residual heat indicator H Once the cooking zone is turned off the symbol H lights up on the display to indicate the presence of residual heat which can be used for warming or thawing foodstuffs Once the O H symbol disappears the cooking zone will not have cooled down completely Beware risk of burns e After activating a certain cooking zone C the heat setting must be above zero the dual circuit is automatically engaged e The external circuit if disengaged relevant to an activated cooking zone the heat setting must be above zero can be engaged by pressing the dual circuit button F A dot G adjacent to the relevant cooking zone appears once the dual circuit is engaged e Pressing the dual circuit button F re engages the external circuit This can be done at any time In order to ensure greater safety during operation the cooker hob is equipped with a time limit device for each single cooking zone The operating time depends on the last heat setting selected If the heat setting is not modified for a long period the cooking zone turns off automatically after a certain period of time that depends on the selected heat setting see table below Heat setting 1 2 3 4 45 6 7 8 9 DORI Beles Sees ae aes aes G 20 Safety function and error signals The
14. ill be delayed by a few minutes up to 10 minutes We recommend using pots with dark and flat base for boiling large amounts of water 17 Energy saving e Do not use clay pots as these may scratch the glass ceramic surface e The diameter of the pot base must match that of the cooking zone Using pots that are too small causes energy wastage and may damage the cooker hob e Use the lid if compatible with the type of food preparation e The pots must be suitably sized according to the amount of food being cooked Preparing small amounts of food in large pots is a waste of energy e Foodstuffs that require long cooking times may be cooked in pressure cookers e Cook potatoes and the various types of vegetables using little water the food will cook well provided the pot is always properly covered with the lid Once the water reaches boiling point lower the heat setting to a level that ensures slow boiling 18 Cooker hob controls Cooker hob operation Turning the cooker hob on Turning the cooking zones on t HOB MODEL 1 7316 000 1 Front left Hi Light cooking zone 2 Rear central Hi Light cooking zone 3 Front right Hi Light cooking zone 4 Cooker hob control unit A Cooker hob on off sensor B Heat setting or residual heat indicators C Cooking zone on selection sensor D Safety lock child safety device on off sensor E Sensor F Dual circuit sensor G Indicator signalling the additional heating
15. ower cord capable of withstanding the load indicated on the rating plate The earth wire is identified by the yellow green jacket The plug must always be accessible Basic After each connection to the mains electricity basic configuration of the configuration of sensors must be carried out to ensure their optimal operation All the the sensors to displays turn on for a few seconds There must be no objects on the hob the environment surface during sensor configuration Otherwise the configuration for model 7316 000 only 25 interrupts and will not resume until the objects are removed The hob may not be used during this operation WARNING Before each operation disconnect the appliance from the mains electricity Depending on the mains voltage the appliance must be connected according to the electrical diagram below The protection conductor equipotential protection conductor must be connected to the earthing clamp The connection wire must be fed through the bracket that protects it against accidental movements Once the connection is completed turn on all the cooking zones for at least 3 minutes to verify their operation ae The following wires can be used for the electrical connection diagram e Type HO5 RR F rubber coated cables with yellow green wires e PVC type HO5VV F connection cables with yellow green wires or similar cables pospwona 1 2 3 4 5 380 415V 220 240V 4x2 5 mm 3x4 0 mm 26
16. subject to change without prior notice Important warnings 2 Glass ceramic cooker hob model 5 0 7316 000 8 Glass ceramic cooker hob model 0 7352 010 Cooker hob cleaning and 9 maintenance Cooker hob installation 10 Connection to the mains electricity 11 Specifications 13 15 IMPORTANT WARNINGS Installation of the appliance and connection to the mains electricity must be carried out by qualified personnel only e Several parts of the appliance heat up during use Keep children away from the appliance and warn them of the risk of burns e Overheated fat can easily ignite Be extremely careful when preparing dishes that require the use of bacon fat or oil e g chips e Do not operate the cooking zones without any pots on them e Do not use the appliance to heat the room e The glass ceramic surface must not be used as a worktop Sharp objects may scratch the cooker hob surface e Do not place objects such as knives forks spoons or lids on the glass ceramic cooker hob as they may overheat e It is forbidden to prepare dishes in plastic or aluminium containers Do not place plastic or aluminium objects on the glass ceramic hob when its surface is hot e Be careful that the power cord of other appliances does not come into contact with the hot cooking zones e Do not store objects sensitive to heat variations below the appliance e g detergents spray cans etc e Do not use the glass ceramic hob if the
17. t use aggressive and abrasive detergents pot scrubbers and stain or rust removers e Do not operate the cooking zones without any pots on them Do not use the appliance to heat the room e Make sure that the cooking zones and pots are always clean and dry so as to ensure optimal heat transmission and to avoid damaging the glass ceramic surface e Overheated fat can easily ignite Be extremely careful when preparing dishes that require the use of bacon fat or oil e g chips e Do not place wet pots or steamy lids on the cooking zones Dampness damages the cooking zones e Do not leave warm pots to cool on cold cooking zones i e that have been inactive as the condensation that forms underneath the pot accelerates corrosion Important warnings concerning the glass ceramic surface e Although the glass ceramic cooker hob reaches the pre set temperature very quickly the surrounding surface remains cold e The cooker hob resists temperature variations e The cooker hob can withstand knocks and will not damaged by positioning pots with added force e Do not use the glass ceramic surface as a worktop Sharp objects may scratch it e It is forbidden to prepare dishes in aluminium or plastic containers on hot cooking zones Do not place any plastic or aluminium object e g aluminium foil on the glass ceramic surface e Do not use the glass ceramic hob if the surface is broken or cracked Pointed objects that fall on the glass ceramic ho
18. tance between the panel comprising the cooker hob and the rear wall is indicated in the picture Cut out measurements for glass ceramic built in Di cooker hob 50mm 25 40mm The cooker hob may only be installed in a worktop 25 mm to 40 mm thick The underlying kitchen cabinet must not have a drawer It must be fitted with a horizontal bar placed 20 mm under the lower edge of the worktop The space between the bar and cooker hob must remain empty A slit at least 50 mm high must be cut into the rear end of the cabinet along its entire width An oven can be installed beneath the cooker hob provided it is equipped with a cooling fan FORNO VENTILATO Prior to installing the oven the cabinet rear panel adjacent to the oven s ventilation opening must be removed Likewise the front end must have an opening at least 5 mm high 24 Installation procedure The worktop must be completely level Protect the cut out surfaces Screw on the support elements provided using the respective screws on the front and rear end of the cooker hob already configured with the relative holes and slots Connect the cooker hob to the mains electricity consult the connection instructions
Download Pdf Manuals
Related Search