E-flite C-Ray 180
Contents
1. Questions Assistance and Services Your local hobby store and or place of purchase cannot provide warranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry or call 877 504 0233 toll free to speak to a Product Support representative Inspection or Services H this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content _ service center_render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instruct2. 4V 430mAh 2S 7 4V 20C Li Po 20AWG JST 20C Lipo JST 2S 430mA 20C Li Po 20AWG JST Celectra 80W AC DC E flite 80W AC DC Celectra 80W AC EFLC3025 Multi Chemistry Bat Multi Akku Ladeger t Ge SE DC Carica batterie tery Charger EU Cer eee Finn o 1 EFLANO o Power Meter Meter Power Meter E flite Lastmessger t flite E flite Lastmessger t Multimatre E flite Multimatre E flite flite Misuratore di Misuratore di potenza DX6i DSMX 6 Channel DX6i DSMX 6 Kanal Emetteur DX6i DSMX DX6i DSMX Trasmet Transmitter Sender 6 voies titore 6 canali DX7s DSMX Spektrum DX7s Emetteur DX7s DSMX DX7s DSMX ER Channel Transmitter 7 Kanal Sender 7 voies Trasmettitore 7 canali Spektrum DX8 nur Emetteur DX8 DSMX DX8 DSMX e DSMX Spektrum DX18 nur Emetteur DX18 DX18 DSMX Transmitter Sender DSMX 18 voies trasmettitore 18 canali Parts Contact Information Kontaktinformationen fur Ersatzteile Coordonn es pour obtenir des pi ces d tach es Recapiti dei distributori Country of Purchase Horizon Hobby Address Phone Number Email Address 4105 Fieldstone Rd 888 959 2305 United States Champaign Illinois 61822 USA sales horizonhobby com Units 1 4 Ployters Rd Staple Tye 44 0 1279 641 097 Harlow Essex sales horizonhobby co uk CM18 7NS United Kingdom United Kingdom Horizon Hobby Limited Christian Junge StraBe 1 49 0 4121 2655 100 Aoro DOY GMU 25337 Elmshorn Germany oe ane de 11 Rue Georges
3. safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy Safety Precautions and Warnings e Always keep a safe distance in all directions around your model to avoid collisions or injury This model is controlled by a radio signal subject to interference from many sources outside your control Interference can cause momentary loss of control e Always operate your model in open spaces away from full size vehicles traffic and people e Always carefully follow the directions and warnings for this and any optional support equip ment chargers rechargeable battery packs etc e Always keep all chemicals small parts and anything electrical out of the reach of children e Always avoid water exposure to all equipment not specifically designed and protected for this purpose Moisture causes damage to electronics e Never place any portion of the model in your m
4. the airframe as well as damage to the ESC and motor NOTICE Crash damage is not covered under warranty Repairs Thanks to the Z Foam construction of this aircraft repairs to the foam can be made using virtually any adhesive hot glue regular CA epoxy etc When parts are not repairable see the Replacement Parts List for ordering by item number For a listing of all replacement and optional parts refer to the list at the end of this manual NOTICE Use of CA accelerant on your aircraft can damage paint DO NOT handle the aircraft until accelerant fully dries NOTICE When you are finished flying never keep the aircraft in the sun Do not store the aircraft in a hot enclosed area such as a car Doing so can damage the foam cet Flight Checklist 1 Disconnect the flight battery from the ESC required for safety and battery life ko 2 Power OFF the transmitter 3 Remove the flight battery from the aircraft ina 4 Recharge the flight battery 5 Store the flight battery apart from the aircraft and monitor the battery charge 6 Make note of flight conditions and flight plan results planning for future flights 11 Service of Power Components Disassembly A CAUTION Always disconnect the battery before handling or adjusting the propeller or motor Failure to do so could result in personal injury Remove the canopy Carefully remove the propeller screw A washer B and prop
5. tip in order to be level with the rest of the wing see illustration Centering Controls After First Flights If the model requires excessive transmitter trim return the transmitter trim to zero and adjust the linkages mechanically so that the control surfaces are in the flight trimmed position Adjusting the Center of Gravity CG The recommended CG location is 18mm 0 71 inch forward from the front edge of the servo casing This CG location has been determined with the recommended 450mAh 2S 7 4V 30C Li Po battery installed in the battery cavity Applying Decals Customize your aircraft with decals 1 Ensure the surface area is clean 2 Cutand remove the desired decals from the decal sheet 3 Press the decal on the aircraft in the desired location Flying Tips and Repairs Consult local laws and ordinances before choosing a location to fly your aircraft We recommend flying your aircraft outside in no greater than moderate winds Always avoid flying near houses trees wires and buildings You should also be careful to avoid flying in areas where there are many people such as busy parks schoolyards or soccer fields Range Check your Radio System After final assembly range check the radio system with the aircraft Refer to your specific transmitter and receiver instruction manuals for range test information A CAUTION Keep hands away from the propeller Always assume th
6. Charpak 33 0 1 60 18 34 90 77127 Lieusaint France KEE com Room 506 No 97 Changshou Rd 86 021 5180 9868 Horizon Hobby China Shanghai China 200060 un com cn owe Horizon hrs hrs 2013 Horizon Hobby Inc E flite Z Foam C Ray DSM DSM2 DSMX Celectra JR ModelMatch Plug N Play and the Horizon Hobby logo ADVANCING ELECTRIC FLIGHT The Spektrum trademark is used with permission of Bachmann Industries Inc Patents pending www e fliterc com EFL3075 Created 03 13 39226
7. e location on this aircraft to measure the recommended low and high rate control throws distance in both directions Elevons From the center line guide A deflect the trailing edge of the elevon B ER Control Direction Test Bind your aircraft and transmitter before doing these tests Move the controls on the transmitter to make sure the aircraft control surfaces move correctly and in the proper direction Always keep throttle at the low position during testing mu Aircraft Reaction Command Up Elevator Command Down Elevator Command Stick Left Control Centering Before the first flights or in the event of an ac cident make sure the flight control surfaces are centered Adjust the linkages mechanically if the control surfaces are not centered 1 Make sure the control surfaces are neutral when the transmitter controls and trims are centered The transmitter sub trim must always be set to zero 2 When needed use a pair of pliers to carefully bend the metal linkage see illustration 3 Make the U shape narrower to make the connector shorter Make the U shape wider to make the linkage longer When centering the elevons the control surface will not directly line up with the edge of the wing tip due to the wing tip s washout The top of the elevon will line up with the approximate middle of the edge of the wing
8. e motor is powered ON and that the propeller blades may turn at any time Flying This aircraft is extremely responsive to control input Fly at low rate settings until you are familiar with its response Fly your first attempts at high rate settings at high altitude and slow speeds Hand Launching When hand launching your aircraft alone hold the aircraft in one hand and the transmitter in the other Hold the aircraft in the finger grips on the underside of the aircraft Firmly throw the aircraft directly into the wind angled slightly up 5 to 10 degrees above the horizon When the propeller is clear of your hand apply throttle Climb to check the trim Once the trim is adjusted begin exploring the flight envelope of the aircraft Landing Make sure to land on a soft surface like grass Fly the aircraft into the wind approximately 6 inches 15cm or less above the surface using a small amount of throttle for the entire descent Keep throttle on until the aircraft is ready to flare During flare keep the wings level and the aircraft pointed into the wind Before the aircraft touches down always fully decrease throttle to avoid damage to the propeller motor ESC or other components A CAUTION Never catch a flying aircraft in your hands Doing so could cause personal injury and damage to the aircraft NOTICE If a crash is imminent reduce the throttle and trim fully Failure to do so could result in extra damage to
9. e off position A CAUTION Always keep hands away from the propeller When armed the motor will turn the propeller in response to any throttle movement Control Horn and Servo Arm Settings This illustration shows the factory settings for linkages on the control horns and servo arms Eug Lower throttle and throttle trim to lowest settings p Power ON the transmitter Remove the canopy and install the flight battery on the hook and loop strip then connect the battery to the ESC noting proper polarity mf Series of tones Y Continuous LED Transmitter and Model Setup Transmitter Setup When using a DX6i transmitter servo Flying wings are controlled by elevons the reversing on the elevator channel moveable surfaces on the C Ray wing Elevons is required combine aileron and elevator controls and mix them When using a DX7s DX8 or DX18 transmitter together electronically through the transmitter set the transmitter wing configuration to Make sure both elevons move up and down travel Elevon B the same amount This model tracks well when the left and right elevon travel the same amount in response to the control stick See the Control Centering instructions for centering the control surfaces High rou Aileron 10 0 Elevator 10 0 Dual Rates High Low Aileron 7mm A V 5mm A VW Elevator 7mm A V 5mm A V Measuring Control Throws Below is th
10. eller C Remove the propeller spacer setscrew D and propeller spacer E from the motor shaft The motor housing and shaft F are magnetically secured to the motor Remove the motor housing and shaft by pulling them away from the motor Repair or replace the motor housing and shaft as necessary Remove the top screw G from the firewall to remove the motor H The motor magnet may attract screws to the motor Disconnect the motor wire connectors from the ESC Remove the motor from the firewall Assemble in reverse order e Connect the motor wire connectors to the ESC so that the propeller turns clockwise facing the rear of the aircraft If the motor turns in the wrong direction switch any 2 motor wires e The propeller size numbers 4 5 x 4 must face forward towards the front of the aircraft for correct propeller operation Troubleshooting Guide Problem Possible Cause Solution Aircraft will ESC did not arm because throttle stick and or Lower throttle stick and throttle trim to lowest not respond to throttle trim too high setting throttle but re sponds to other Throttle channel is reversed Reverse throttle channel on transmitter controls Motor disconnected from ESC Make sure motor is connected to the ESC Servo travel set up is less than 100 Adjust servo travel to 100 or slightly greater Extra propeller Damaged propeller prop shaft or motor Replace damaged parts det Prop screw is too loose Tight
11. eltren aye C Ray 180 Lite HORIZzIN Instruction Manual Bedienungsanleitung Manuel d utilisation Manuale di Istruzioni Elite ADVANCING ELECTRIC FLIGHT NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit www horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury A WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this product in a
12. en the prop screw Prop is out of balance Remove and balance propeller or replace with a balanced propeller Reduced flight Flight battery charge is low Completely recharge flight battery lime or aircraft EE Speller installed backward install propell Flight battery damaged Replace flight battery and follow flight battery instructions Flight battery is too cold Make sure battery is warm before use Battery capacity too low for flight conditions Replace battery or use a larger capacity battery Aircraft will not Transmitter too near aircraft during binding process Power off transmitter move transmitter a Bind during larger distance from aircraft disconnect and binding to trans reconnect flight battery to aircraft and follow mitter binding instructions Bind switch or button not held long enough during Power off transmitter and repeat bind process bind process Hold transmitter bind button or switch until receiver is bound Flight battery Transmitter battery charge is too low Replace recharge batteries Bind pins on receiver are not correctly Connect receiver bind pins as instructed and connected bind transmitter to receiver Aircraft or transmitter is too close to large metal Move aircraft and transmitter to another object wireless source or another transmitter location and attempt binding again Aircraft will not Transmitter too close to aircraft during connecting Power off transmitter move transmitter a connect after proc
13. er Binding Refer to your transmitter and receiver manuals for binding instructions nil sep ARE 20 48 ECENER oy LITER NAN Gz Gg Installing the Flight Battery 1 Remove the canopy 2 Center the included strip of hook and loop tape on the bottom of your battery 3 Install the battery in the battery cavity then press the battery onto the hook and loop strip A See the Adjusting the Center of Gravity instructions for more information 4 Connect the fully charged flight battery to the ESC See the Arming the ESC instructions for correct connection of the battery to the ESC 5 Reinstall the canopy A CAUTION Always disconnect the Li Po battery from the ESC when not flying to eliminate power supplied to the motor The ESC does not have an arming switch and will respond to any transmitter input when a signal is present A CAUTION Always disconnect the Li Po battery from the ESC when not flying to avoid over discharging the battery Batteries discharged to a voltage lower than the lowest approved voltage may become damaged resulting in loss of performance and potential fire when batteries are charged Arming the ESC Arming the ESC also occurs after binding but subsequent connection of a flight battery requires the following steps If you accidentally connect the battery while the throttle is fully opened a musical tone will sound and the ESC will not arm until the throttle is returned to th
14. ess larger distance from aircraft disconnect and binding to trans reconnect flight battery to aircraft mitter Flight battery Transmitter battery charge is too low Replace recharge batteries Transmitter may have been bound using different Bind aircraft to transmitter DSM protocol ind pins on receiver are connected Ensure bind pins on receiver are not connected Aircraft or transmitter is too close to large metal Move aircraft and transmitter to another loca object wireless source or another transmitter tion and attempt connecting again Control surface Control surface control horn linkage or Replace or repair damaged parts and adjust does not move _ servo damage controls Wire damaged or connections loose Do a check of wires and connections connect or replace as needed Flight battery charge is low Fully recharge flight battery Control linkage does not move freely Make sure control linkage moves freely Controls reversed Transmitter settings reversed Adjust controls on transmitter appropriately Motor power Battery voltage is down to the point of receiver ESC Recharge flight battery or replace battery that quickly decreas Low Voltage Cutoff LVC is no longer performing es and increases then motor loses power Aircraft bound to different model memory Select correct model memory on transmitter ModelMatch radios only 13 Limited Warranty What this Warranty Covers Horizon Hobby Inc Horizon warrants t
15. ions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service e
16. model as well as important safety considerations Box Contents Table of Contents Preflight Checklist Battery Selection Low Voltage Cutoff LVC Installing the Flight Battery Arming the ESC distances Control Horn and Servo Arm Settings Transmitter and Model Setup Control Direction Test Control Centering canino Adjusting the Center of Gravity CG Specifications k 13 5 in 342mm 21 7 in 550mm S 4 40 oz 125 g To register your product online go to www e fliterc com Installing a Receiver d Vullen 10 Flying Tips and Repairs s e 11 POSE Flight Checklist iii 11 Service of Power Component 12 Troubleshooting Guide rn 13 Limited Warranty o e 14 Warranty and Service Information 01000100a 15 Compliance Information for the European Union 15 Replacement Parts rire 58 Optional Parts and Accessories eee 59 Parts Contact Information 59 installed Z o Gm 180 Brushless Outrunner Motor 2500Kv AC EFLM7005 E em Brushless ESC EFLA7200 2 3 g Super Sub Micro Servo B Ge Needed to Complete Recommended Battery 450mAh 2S 7 4V 30C Li Po 18AWG JST EFLB4502SJ30 Recommended Battery Charger Celectra 80W AC DC Multi Chemistry Battery Charger EFLC3025 Recommended Receiver Spektrum AR6310 DSMX Nanolite 6 Channel Receiver Air SPMAR6310 Recommended Transmitter Full Range DSM2 DSMX technology with adj
17. n of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice 14 WARRANTY SERVICES
18. o the original purchaser that the product purchased the Product will be free from defects in materials and workmanship at the date of purchase What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Horizon Hobby authorized service center v Product not purchased from an authorized Horizon dealer or vi Product not compliant with applicable technical regulations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be that Horizon will at its option either i service or ii replace any Product determined by Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement decisions are at the sole discretio
19. orizonhobby de 11 Rue Georges Charpak 33 0 1 60 18 34 90 EES Horizon Hobby SAS 77127 Lieusaint infofrance horizonhobby com China Horizon Hobby Room 506 No 97 Changshou 86 021 5180 9868 China Rd Shanghai China 200060 info horizonhobby com cn Compliance Information for the European Union Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2013041401 Product s EFL C Ray PNP C Item Number s EFL3075 Equipment class 1 Horizon Product Support All other products United Kingdom Horizon Hobby Limited Germany The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European EMC Directive 2004 108 EC EN55022 2010 AC 2011 EN55024 2010 Signed for and on behalf of TPE amp Lee Horizon Hobby Inc Champaign IL USA Steven A Hall Apr 14 2013 Executive VP Chief Operating Officer International Operations and Risk Management Horizon Hobby Inc Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural WE resou
20. outh as it could cause serious injury or even death e Never operate your model with low transmitter batteries e Always keep aircraft in sight and under control e Always use fully charged batteries e Always keep the transmitter powered on while aircraft is powered e Always remove batteries before disassembly e Always keep moving parts clean e Always keep parts dry e Always let parts cool after use before touching e Always remove batteries after use e Always ensure failsafe is properly set before flying e Never operate aircraft with damaged wiring e Never touch moving parts hank you for purchasing the exciting new E flite flying wing the C Ray 180 PNP Constructed of durable Z Foam material this agile little flying wing is designed to bounce back from mild impacts time and time again The perfect airplane for parks and small flying areas the C Ray airplane delivers snappy fast and fun performance that intermediate through expert pilots will love With its included decal sheet personalizing your C Ray airplane is easy so you can distinguish which airplane is yours when flying with buddies Although this great flying plane requires very little assembly out of the box we encourage you to take a little time to absorb the content of this manual before your first flight Inside you ll find helpful setup tips a handy troubleshooting guide and guidelines to help you select appropriate flying fields for this
21. quate power to the receiver and servos to land NOTICE Repeated flying to LVC will damage the the airplane battery When the motor power decreases land the aircraft immediately and replace or recharge the flight battery Always disconnect and remove the Li Po battery from the aircraft after each flight Charge your Li Po battery to about half capacity before storage Make sure the battery charge does not fall below 3V per cell Failure to disconnect the battery will result in trickle discharge Installing a Receiver Be sure you choose a receiver that uses JST ZHR 3 micro connectors We recommend the Spektrum AR6310 DSMX Nanolite 6 Channel Receiver SPMAR6310 1 Remove the canopy 2 Install the receiver in the fuselage using the included double sided servo tape 3 Connect the left elevon when facing the rear of the aircraft servo connector to the elevator channel of the receiver 4 Connect the right elevon when facing the rear of the aircraft servo connector to the aileron channel of the receiver 5 Connect the ESC connector to the throttle channel of the receiver Some JST type servos have a different polarity than Spektrum servos Plug the servo leads into the appropriate servo ports in the receiver noting the polarity of the servo connector See illustration for correct connector polarity e A Orange Wire Signal e B Brown Wire middle wire Negative e C Red Wire Positive Transmitter and Receiv
22. rces and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product IS 58 Replacement Parts Ersatzteile Pieces de rechange Recapiti per i ricambi Part Nummer Num ro Codice EFL307501 EFL307502 EFL307503 EFL307504 EFLM7005 EFLM700501 EFLA7200 EFLR7105 EFLM1933A EFLP4540E Description Beschreibung Description Descrizione Replacement Air E flite C Ray 180 Structure de rempla Ricambio cellula frame C Ray 180 Ersatzrumpf cement C Ray 180 C Ray 180 pen E flite C Ray 180 Verri re C Ray 180 c Motor Mount amp E flite C Ray 180 Support moteur avec Sy SE pporto motore e Ga iad Motortrager m Zbh visserie C Ray 180 viteria C Ray 180 Decal Sheet C Ray E flite C Ray 180 Planche de d coration Foglio adesivi 180 Dekorbogen C Ray 180 C Ray 180 180 Brushless E flite C Ray 180 Moteur brushless Motore brushless 180 Outrunner Motor Brushless Aussen 180 cage tournante a cassa rotante 2500Kv C Ray 180 laufer 2500Kv C Ray 180 C Ray 180 180 Motor Outer E flite C Ray 180 Cloche et axe pour Housing and Shaft Motor 2500 KV BL180 2500Kv Carcassa motore 180 e 2500Kv C Ray 180 ER und C Ray 180 albero C Ray 180 8 Amp Bru
23. shless E flite 8 Amp Brush Contr leur brushless Regolatore ESC ESC less ESC 8A brushless 8A 3 Gram Super Sub E flite 3 Gram Super Super sub micro Servo super sub micro Micro Servo Sub Micro Servo servo 3g 3 grammi Prop Adapter with E flite Prop Adapter Adaptateur d h lice Adattatore elica con Setscrew 1 5mm m Schraube 1 5mm avec vis 1 5mm grano 1 5mm 4 5 x 4 Electric E flite 4 5 x 4 Elektro Adaptateur d helice Elica per elettrico Propeller Propeller avec vis 1 5mm 4 9X Optional Parts and Accessories Optionale Bauteile und Zubehorteile Pi ces optionnelles et accessoires Parti opzionali e accessori Part e Nummer Namero e Codice Description Beschreibung Description Descrizione EFLB4502SJ30 450mAh 2S 7 4V 30C 450mAh 2S 7 4V 30C Batterie Li Po 7 4V 450mAh 2S 7 4V 30C Li Po 20AWG JST Li Po 20AWG JST 25 450mA 30C Li Po 20AWG JST AR6310 DSMX Spektrum 6 Kanal R cepteur AR6310 AR6310 DSMX SPMAR6310 Nanolite 6 Channel Nanolite Empfanger DSMX Nanolite 6 Nanolite ricevitore 6 Receiver Air DSMX voies canali Air EFLA230 Charger Lead with JST E flite Ladekabel m Cable de charge avec Cavo di carica con Female JST Buchse prise JST femelle femmina JST EFLA250 Park Flyer Tool Assort dei ortiment ASSortiment d outils Park Flyer assortimen ment 5 pc 5 teilig 9 park flyer 5pc to attrezzi 5 pc EFLB4302SJ 430mAh 2S 7 4V 20C E flite 430mAh 2S Batterie Li Po 7
24. stimates will be billed a minimum of hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and serviced Further the sender will be responsible for Conditions found on our website http www horizonhobby arranging return shipment of the un serviced Product com content _service center_render service center through a carrier of the sender s choice and at the sender s expense Horizon will hold non compliant Product for a period of 60 days from notification after which it will be discarded ATTENTION Horizon service is limited to Product compliant in the country of use and ownership If received a non compliant Product will not be Warranty and Service Information Country of Purchase Horizon Hobby Address Phone Number Email Address 4105 Fieldstone Rd 888 959 2305 United Stat eae peice Cental Champaign Illinois Online Repair Request visit vi po 61822 USA www horizonhobby com service 4105 Fieldstone Rd 877 504 0233 Champaign Illinois productsupport horizonhobby 61822 USA com Units 1 4 Ployters Rd Staple Tye 44 0 1279 641 097 Harlow Essex sales horizonhobby co uk CM18 7NS United Kingdom Horizon Technischer Christian Junge StraBe 1 49 0 4121 2655 100 Service 25337 Elmshorn Germany service h
25. ust able dual rate expotential and elevon mixing DX6i and up Gace wi Wey Preflight Checklist C v in 1 Charge the flight battery 2 Install the flight battery in the aircraft once it has been fully charged 6 Adjust the center of gravity in 7 Perform a radio system Range Check 8 Find a safe and open area a 3 Bind the aircraft to the transmitter ina 4 Make sure the linkages move freely 5 Perform the Control Direction Test with the transmitter Battery Selection 9 Plan flight appropriate for flying location We recommend the E flite 450mAh 2S 7 4V 30C Li Po 18AWG JST EFLB4502SJ30 battery If using another battery it must be at least a 20C 430mAh battery Your battery should be approximately the same capacity dimensions and weight as the recommended Li Po battery to fit in the fuselage without changing the center of gravity Low Voltage Cutoff LVC When a Li Po battery is discharged below 3V per For your first flights set your transmitter timer or cell it will not hold a charge The aircraft s ESC a stopwatch to 8 minutes Adjust your timer for protects the flight battery from over discharge using longer or shorter flights once you have flown the Low Voltage Cutoff LVC model Flights of 10 minutes are achievable with Once the battery discharges to 3V per cell the LVC ee battery if using proper throttle will reduce the power to the motor in order to leave 9 ade
Download Pdf Manuals
Related Search