Peerless HT642-003 flat panel wall mount
Contents
1. 0 cece errr ne iirin 8 Attaching Mounting Bracket Using Tilt Option 000 i eer O LLARY EEEEL LLA AL NEL T 9 20f 8 ISSUED 07 07 11 SHEET 125 9221 1 Before you start make sure all parts listed are included with your product PARTS LIST Description wall plate adapter bracket 1 4 x 2 5 round phillips screw M5 x 12 mm socket pin serrated washer head screw 201 1601 201 1931 520 9521 510 1064 5 1 015 C03 560 1129 520 2051 560 9708 540 1008 590 0097 14 x 2 5 wood screw 4 mm security allen wrench M8 x 16 mm phillips pan screw toggler washer Alligator amp concrete anchor ce ZzoaTtmtmodwD p gt or hh DOD Lf Some parts may appear slightly different than illustrated Cry N MAN 777777777777 7i AN NAWN WM ul AN A SS A LLU ANN MM AN 3 of 8 ISSUED 07 07 11 SHEET 125 9221 1 Attaching Adapter Bracket to Screen Attach adapter bracket B to back of plasma screen using four M8 x 16 mm phillips screws G Screen A WARNING e Do not overtighten Overtightening may cause per manent damage to the screen Torque to 26 35 in Ib 30 40 kg cm Installation to Wood Stud Walls Use a stud finder to locate center of studs For mounting to 16 centers Using mounting bracket A as2. 3 Place wall mount assembly over anchors and secure with 14 x 2 1 2 6 mm x 65 mm wood screws E and washers I as shown in figure 3 4 Make sure wall plate is level and tighten all fasteners A WARNING Tighten wood screws firmly but do not overtighten Overtightening can damage the screws greatly re ducing their holding power Place plate A over anchors J and secure with screws E with washers I 3 Never tighten in excess of 80 in Ib 9 N M A WARNING Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster drywall or other finishing material as shown below If mount ing to concrete wall covered with plaster drywall is unavoidable plaster drywall up to 5 8 thick must be counter bored as shown below Be sure concrete anchors do not pull away from concrete when tight ening screws If plaster drywall is thicker than 5 8 custom fasteners must be supplied by installer Tighten all fasteners INCORRECT CORRECT 0 concrete cconcrete o c plaster 4 NW drywall 1 plaster j i drywall CUTAWAY VIEW 5of8 ISSUED 07 07 11 SHEET 125 9221 1 Installation to Metal Stud 4 WARNING Product must be mounted through drywall that has a minimum t
3. a template drill four 5 32 4 mm dia holes to a minimum depth of 2 5 64 mm Attach mounting bracket A to centers of wood studs using four 14 x 2 5 wood screws E and four washers I as shown below 4of8 ISSUED 07 07 11 SHEET 125 9221 1 Installation to Solid Concrete and Cinder Block Wall A WARNING e When installing Peerless wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block Cinder block must meet ASTM C 90 specifica tions It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor Make sure that the supporting surface will safely support the combined load of the eguipment and all attached hard ware and components Position adapter bracket A at desired position on wall 3 Use mounting bracket making sure that it is level as a concrete template to mark holes Drill six 1 4 6 mm dia holes a to a minimum depth of 2 1 2 64 mm Concrete must be 2000 psi density minimum Insert anchors J in holes J flush with wall as shown in figure 5
4. er brackets B to mounting bracket A attach two M5 x 12 mm serrated washer head socket pin screws D into the threaded inserts of adapter brackets B and through the slots on the sides of mounting bracket A Tighten with the 4 mm security allen wrench F For tilt option skip to Step 8 D 7of8 ISSUED 07 07 11 SHEET 125 9221 1 Mounting Bracket Using Tilt Option Remove top two M5 x 12 mm socket pin serrated washer head screws D attached to wall plate A Loosen two M5 x 12 mm socket pin serrated washer head screws D in slot as shown in Detail 1 Once desired tilt is established tighten two M5 x 12 mm socket pin serrated washer head screws D in slots SLOT Detail 1 8 of 8 ISSUED 07 07 11 SHEET 125 9221 1 2010 Peerless Industries Inc All rights reserved Peerless is a registered trademark of Peerless Industries Inc All other brand and product names are trademarks or registered trademarks of their respective owners
5. hickness of 1 2 and into metal studs 26 gauge or heavier Make sure that the wall will safely support the combined load of the eguipment and all attached hardware and components Make sure that togglers are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Using a stud finder locate and mark the edges of the metal stud used in mounting this product Use of an edge to edge stud finder is highly recommended Use a level to draw a level vertical line down the center of the stud Level wall plate and mark the center of the four mounting holes Make sure that the mounting holes are on the stud center line Drill four 1 2 holes through drywall and metal studs Note It may be necessary to drill 5 32 pilot holes prior to drilling 1 2 holes Rotate toggler H clockwise to wedge it against inside walls of metal stud Slide plastic cap forward while pulling back firmly on ring Break off excess 6of8 ISSUED 07 07 11 SHEET 125 9221 1 Attaching Mounting Bracket Using Hook On Option Attach four M5 x 12 mm serrated washer head Position slots of adapter brackets B onto the socket pin screws D to the holes on the sides of four M5 x 12 mm serrated washer head socket pin mounting bracket A using the 4mm security allen screws D attached to mounting bracket A wrench F provided B SLOT To secure adapt
6. peerless V Installation and Assembly Flat Tilt Wall Mount for VESA 400x400 Model HT642 003 WW a aaa ce aa i WN GRY NEUR NW YU NN teeta eee eee Y yg Fei ied Td i yd yh dg id DD ee E DI I Fd ee Y YN ded i mwyd pedd lt Max Load Capacity 100 Ib 45 4 kg 3215 W North Ave Melrose Park IL 60160 800 729 0307 or 708 865 8870 Fax 708 865 2941 www peerlessmounts com ISSUED 07 07 11 SHEET 125 9221 1 Note Read entire instruction sheet before you start installation and assembly A WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings please call Peerless customer service at 1 800 729 0307 This product should only be installed by a qualified professional Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components Never exceed the Maximum Load Capacity of 100 Ib 45 4 kg If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting eguipment to safely lift and position eguipment Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holding powe
7. r This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet To mount this product to an alternative supporting surface contact Peerless customer care at 1 800 865 2112 This product was designed to be installed on the following wall construction only WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED Wood Stud None Wood Beam None Solid Concrete None Cinder Block None Metal Stud None Brick Contact Customer Service Other or unsure Contact Customer Service Ll Ll 1 e 1 Dd 1 Tools Needed for Assembly e stud finder edge to edge stud finder is recommended phillips screwdriver e drill with 1 4 and 5 32 drill bits e 5 16 socket wrench Table of Conten Pars FE Y veut Ree thay HYF NF EWYRTH FR Gasol A RAY RF PN REF WEAR ER HA HR FR AF HE FFF FA FO FFR ay 3 Attaching Adapter BraCKet t0O SCTGeD e ss ci yrei wyo ddon Fynddn YRFA A Yny wg Ten dvs O ySM OF dnd UFL LLYW O I Ty ynd ns 4 Inistallationi to Wood Std Walls uiewn ue Tn yw AF ld donc Y OA ydw UU Tyd Y YT Ud wyaf Dydy Fd TU MAE Dy wdd nnd 4 Installation to Solid Concrete and Cinder Block Wall ecient ie ALLE LLEYN AEL LLED NN HLEE ELE LL ALL ELLA LAF EE DLHE EL LLF9 5 IniStallationi to Metal Stud e e iil dwya iH yW FFWR d YS DANO LLE Od O yg Fd ceva andes saauvedi nA YY Tad O SO 6 Attaching Mounting Bracket Using Hook On Option
Download Pdf Manuals
Related Search