Addonics MSHDUS5LX
Contents
1. option See Advanced Setup Options Setup options 10 1 Language Use this option to select the language of the system currently only English is supported 10 2 Copy Size Controls how much of the source drive to use for copy operations in percentage Default setting is ALL 100 10 3 Startup Menu sets the first menu option to appear after boot Default setting is Copy HDD 10 4 Auto Compare Controls whether or not targets are compared automatically when copy is complete Default setting is OFF 10 5 Button Sound Enables audible beep when pressing buttons Default setting is ON 10 6 Device Info Displays information about connected drives Main display is drive manufacturer and size Press up down to select drives ENT to display model number and firmware revision of selected drive 10 7 System Info Displays firmware version and date Phone 408 453 6212 Email www addonics com support query 4 10 8 Fast Copy When this setting is ON the duplicator will attempt to copy the source drive s contents instead of the entire disk Also controls Compare function Default setting is OFF NOTE Target drive size is still required to be equal to or greater than source Only works with source drives formatted using Master Boot Record If the source drive has a boot record other than MBR the entire disk will be copied as if Fast Copy were OFF If the source drive is formatted with a Master Boot Record and contains only FAT32 or2. 5 Insert the completed adapter into the drive bay with the SATA connector toward the rear metal side up The drive should slide in easily don t force it Step 6 Close the door on the drive bay It should also give little resistance don t force it As soon as the drive is in position it will power up Phone 408 453 6212 Email www addonics com support query 2 Quick Start By default the duplicator will initialize scan for drives and offer the copy function Insert the source and target drives power up the unit wait for the copy function to appear then press ENT Canceling Functions When selecting menu options canceling is done by pressing ESC When the unit is busy performing an operation such as copy verify or overwrite the operation can be canceled by holding the ESC button until the unit beeps Duplicator Functions The duplicator has three menu sections The Main menu Setup Options and Advanced Setup Options Setup Options is accessed through the Main menu Advanced Setup Options is accessed by holding the ESC button from any other menu until the unit beeps Main Menu 1 Copy HDD Scans the ports then copies from the source to any targets found 2 Async Copy HDD Scans the ports then copies from the source to any targets found More drives may be added before the process is complete they will begin the process as soon as they are detected 3 Compare HDD Scans the ports then any targets found will be compar
3. NTFS partitions identical partitions will be created on the target s and only the files will be copied If the source drive with MBR format includes partitions other than FAT32 or NTFS all sectors of all partitions including FAT32 and NTFS will be duplicated Enabling Fast Copy may not produce bootable duplicates 10 9 Auto Start Drive When source drive is present inserting a target drive will cause copy process to begin automatically Default setting is OFF 10 10 Auto Start Timer sets delay in time after target insertion before beginning auto copy process if Auto Start Drive is ON Default setting is OFF no delay 10 11 Tolerance Size Sets the minimum target size in percentage compared to the source that is allowed to use for copying Default is 100 equal in size NOTE Leaving this setting at 100 or using for minor adjustments only is strongly recommended Permitting target size less than source size may result in inaccurate copies 10 12 BootTime Delay This option is used to set boot delay time Default setting is 5 seconds 10 13 Quick Compare sets Compare function to stop after a small amount of data has been verified up to 100MBytes Default setting is OFF 10 14 Copy with Size Causes duplicate drive to report to an operating system the exact same total size as source when copy is complete Works only on drives formatted using a Master Boot Record Default setting is OFF 5 www addonics com Technical Supp
4. 408 453 6212 Email www addonics com support query 6 www addonics com Phone 408 573 8580 Fax 408 573 8588 Email http www addonics com sales query
5. TECHNOLOGIES User Guide 1 5 Combo mSATA HDD Duplicator MSHDUS5LX www addonics com Technical Support If you need any assistance to get your unit functioning properly please have your product information ready and contact Addonics Technical Support at Hours 8 30 am 6 00 pm PST Phone 408 453 6212 Email http www addonics com support query Overview LCD Display Arrow Buttons ENT and ESC keys Source Drive Target Drives LCD Display shows current function selected information or progress Arrow keys used to select menus or options ENT key Used to select options or sub menus select options or starts functions ESC key Used to exit sub menus discard option changes or cancel functions when held mSATA to SATA Adapter Quantity 6 Power Cord U S Version shown WARNING Please remember to set the power supply to your local outlet voltage prior to plugging in the power cord Failure to do so may damage the power supply 1 www addonics com Technical Support M F 8 30 am 6 00 pm Drive Installation Step 1 Insert the mSATA SSD into the mSATA connector on the PCB Step 2 Push down the other end of the mSATA SSD until it is latched securely by the hold down clip NOTE The completed flash drive has the same dimension of a 9mm 2 5 HDD Step 3 Turn over the flash drive Step 4 On the Duplicator move the silver button slightly to the right to open the door Step
6. ed to the source 4 Async Compare Scans the ports then any targets found will be compared to the source More drives to compare may be added before the process is complete they will begin the process as soon as they are detected B PreScan Source Reads all blocks on the source drive to confirm no I O errors are encountered 6 ReScan BUS Manually scans all ports and reports how many units were found 7 Source Size Examines the source drive and reports total space and space used if drive contains compatible partitions Press up down to change display ESC to exit 3 www addonics com Technical Support M F 8 30 am 6 00 pm 8 Secure Erase Scans all ports then erases all data on all connected drives NOTE some drives will remain in a locked state when the process is complete Drives that are locked may not appear to an operating system and will cause an I O error if used as a target in the duplicator If this happens start secure erase again and hold ESC to cancel the operation a few moments after it begins 9 Overwrite Overwrite is used to write data onto the entire hard disk it will destroy all data on all HDDs connected to the duplicator including Source HDD by writing data to all sectors There are 4 sub options One pass zero One pass random 3 pass and 7 pass 10 Setup Enters the Setup menu See Setup Options 11 Adv Setup Enters the Advanced Setup Menu Only available by holding ESC on any Main Menu
7. ort M F 8 30 am 6 00 pm Advanced Setup Options 11 01 Read Error Skip Allows duplicator to ignore I O errors while reading source drive Default setting is OFF 11 02 Update Firmware Used to apply firmware updates Connect a drive formatted as FAT containing one partition with the firmware file in the root directory NOTE This function scans the entire disk before proceeding Providing a drive that is as small as possible is strongly recommended 11 03 Compare Firmware Used to confirm correct firmware Connect a drive formatted as FAT containing one partition with the firmware file in the root directory NOTE This function scans the entire disk before proceeding Providing a drive that is as small as possible is strongly recommended 11 04 Quick Erase HDD scans the ports then quickly erases all sectors on all connected drives 11 05 Full Erase HDD scans the ports then completely erases all sectors on all connected drives 11 06 H W Diagnostic Starts comprehensive tests for Ram LCD buttons ports and Flash 11 07 Load Default Resets all configuration settings to default 11 08 Copy HPA Enables copy functions to duplicate the source drive s Host Protected Area Normally this area is defined as not available to a host controller as defined by ATA SATA specifications 11 09 Burn In Runs a function continuously until aborted Selections are Copy Compare Compare Async Cpy 8 Cmp Async Compare Phone
Download Pdf Manuals
Related Search