Home
StarTech.com Standalone 1:5 USB Flash Drive Duplicator and Eraser – Flash Drive Copier
Contents
1. Defense DoD 5220 as a method of fully erasing a drive to guarantee the data has been deleted NOTE The source drive will not be formatted 6 7 System Update Update the system s firmware version Save the firmware update onto your Flash drive Make sure the firmware update file is un zipped and not in a folder To start press OK on 6 7 System Update and it will automatically start updating When completed turn off the system for 5 seconds and then turn back on The firmware update is now complete 6 8 Calc Checksum Calculate the Checksum number of the Flash drive that s plugged into the source port The Checksum area that is calculated will be based on the copy area that s been set 7 Setup 7 1 Start up Menu Select which function is displayed when the system is first turned on 7 2 Copy Area 7 2 1 System and Files This is also called quick copy mode The system will automatically analyze the source drive s file format If the file format is recognized FAT16 32 NTFS Linux ext2 ext3 ext4 only the data will be copied Otherwise if the file format is not recognized the system will copy the entire storage capacity of the Flash drive including empty space System and Files is enabled by default Starlechcom 11 Hard to find made easy Instruction Manual 7 2 2 Whole Media Set the system to copy the entire Flash drive s content including empty space and file format 7 3 Button Beep Turn audio f
2. of the connected Flash drive in the destination slots 1 Plug the Flash drive into the slot and press OK on Capacity Check The system will quickly report the exact capacity of the connected Flash drive by reporting either a green or red LED Use the up and down arrows to move between slots 2 This function supports Asynchronous operation You can continuously remove and connect multiple Flash drive types without pushing any buttons uuu O0000000000 42 SIZE 1847M 43 SIZE 1847M Capacity OK Wrong Size 752M Green Light Correct Size Red Light Wrong Size NOTE a This function may change the data and format on the Flash drive b To protect the source drive s data the system does not check the capacity of the source drive C If the red LED illuminates indicating an error you can use the up and down arrows for error information 5 Information 5 1 USB Info Show the Flash drive s basic information such as drive type content size and total capacity Port Number 2 USB 1847M T USB total capacity FAT32 39M 4 File content size Device Format Starlechg om 8 Hard to find made easy Instruction Manual 5 2 System Information This function will show information about the system including model number and software version USB 1 2 USB duplicator model Ver 2 28 8 System firmware 6 Utility 6 1 Do Format Insert a Flash drive device into one of the destination slots and press OK to be
3. starting a quality check you can change the range and error limit using functions 6 3 3 Setup Range and 6 3 4 Set Error Limit respectively 6 3 1 H3 Safe 10096 Check the Flash drive s quality by reading the drive After the process has completed the LCD display will show the volume of bad sectors detected and the read speed of the drive 6 3 2 H5 R W 10096 Check the Flash drive s quality by reading and writing to the drive Once completed the LCD display will show the volume of bad sectors detected and the read write speed of the drive 2 Bad 0 18M Media Check OK NOTE This function will delete the content and format of the Flash drive To protect the data on the source drive only the destination ports can be checked 6 3 3 Setup Range Set the 96 of the Flash drive that you would like to check for quality Use the up and down arrows to set the percentage Starlechg om 10 Hard to find made easy Instruction Manual 6 3 4 Setup Error Limit Set the tolerance range when checking for errors on the Flash drive Use the up and down arrows to set the percentage 6 4 Quick Erase Erase the Flash drive s data content Use the up and down arrows to check each port s status 6 5 Full Erase This function completes a single pass overwrite to erase the Flash drive s content and format 6 6 DoD Erase This function completes a three pass overwrite erase which is acceptable by the U S A Department of
4. 2 1 System and Files mi 7 3 Button Beep 7 4 Asynchronous Hold Time 7 5 Target Tolerance 7 6 Asynchronous Mode 7 7 Check Before Copy 7 8 Power Off Time Between Copy Compare 79 Language 7 10 Working Mode 7 11 Set HOD Mode 7 12 Restore Defaults StarTechy om 4 Hard to find made easy Instruction Manual Hardware Operation 1 Copy There are two types of copy modes Asynchronous Copy and Synchronous Copy The system will check the content size of the source before executing the copy function If the source content size is less than the system s buffer memory it will automatically start an Asynchronous copy If the source content size is larger than the system s buffer memory it will copy in Synchronous mode 1 1 Synchronous Copy To configure go to function 7 6 Asynchronous and select Disable If the source s content size is larger than system s buffer memory it will execute Synchronous Copy and ignore which copy mode has been set at function 7 6 Operating Process 1 Plug in the source and destination Flash drive s Select the copy function and USB 1847M EP Reading Content USB 1847M 230M 1 to start press OK The number of target flash plugged in and ready to copy 2 The copy will start automatically if two destination Flash drives are connected Otherwise press OK to start the copy Copy 230M 4 Content size 30 0 18 71M 4 Progressed size Progress
5. StarTech om Hard to find made easy Portable 1 5 USB Flash Drive Duplicator and Eraser USBDUP15 actual product may vary from photos DE Bedienungsanleitung de startech com FR Guide de l utilisateur frstartech com ES Guia del usuario es startech com IT Guida per l uso it startech com NL Gebruiksaanwijzing nl startech com PT Guia do usuario pt startech com For the most up to date information please visit www startech com Manual Revision 07 23 2014 FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circui
6. ed time and percentage Starlechcom 5 Hard to find made easy Instruction Manual 3 When the copy has completed the LCD display will show the total time it took to copy the number of passes and if there were any failures TOTAL OK 1 NG 0 01 06 OK 1 NG 0 NOTE a When the copy is in progress the green LED will flash for each Flash drive that is connected When the copy has finished the green LED will stop flashing and remain illuminated If an error occurs the red LED will illuminate b Do NOT remove the Flash drives while the system is copying green LED is flashing You can cancel duplication by pressing ESC c It is recommended that the source and destination are the same size Copying to or from a larger Flash drive may cause an error and the copy will fail d If copying a Flash drive with NTFS or Linux file formats the destination capacity MUST BE equal or larger than the source s capacity 1 2 Asynchronous Copy NOTE This mode is enabled by default The source s content size must be smaller than the system s buffer memory otherwise the system will automatically duplicate in Synchronous mode To enable Asynchronous mode go to function 7 6 Asynchronous and select Enable Operating Process 1 Plug in the source Flash drive and press OK The system will start to read the source s content into the system s buffer Once completed it will immediately start to copy once a destination Flash dr
7. eedback ON OFF ON by default 7 4 Asyn Hold time Set the time to cancel an Asynchronous copy when you ve temporarily finished copying and all of the Flash drive devices have been removed but the copy job has not been manually cancelled This is to prevent mistakenly overwriting your source drive when you d like to start a new source copy but the previous Asynchronous copy job has not yet been cancelled The default is 30 seconds When the system no longer detects any Flash drive for 30 seconds the system will prompt you to either exit or keep the current copy job 7 5 Target Tolerance Set the tolerance of the capacity gap between the source and destination ports in 96 There are three modes with the default being no limit as follows a Allow Tolerance Users can set the high and low limit 96 of capacity difference between the source and destination drive separately b No Limit Users can disable the capacity limit between the source and destination drive If the data on the source drive is larger than the capacity of the destination drive this will lead to an incomplete failed duplication C 10096 same Users can set the capacity of the destination drives to be the exact same as the source drive If the sizes do not match the duplication will not start 7 6 Asynchronous Mode Choose to disable or enable Asynchronous copy mode If enabled and the data on the source is smaller than the system s buffer memory it will automatica
8. gin formatting 1 This function will automatically detect the capacity of the Flash drive and format accordingly If the Flash drive is already FAT16 or FAT32 the original format will not be changed 2 If the Flash drive s format is NTFS Linux or multi partition FAT the system will format the drive according to the capacity If the capacity is equal or greater than 2GB it will format to FAT32 If the capacity is less than 2GB it will format to FAT16 3 During the format process you can press the up and down arrows to check each Flash drive s formatting status progress and information 6 1 2 FAT Format Format any Flash drive to FAT16 6 1 3 FAT32 Format Format any Flash drive to FAT32 NOTE Only the Flash drive s in the destination ports will be formatted The source will not be formatted StarTechy om 9 Hard to find made easy Instruction Manual 6 2 Measure Speed Measure the read and write speeds of the Flash drive 1 Plug the Flash drive into one of the slots and select function 6 2 Measure Speed then press OK 2 Use the up and down arrows to see the Flash drive s exact read and write speeds for each port amp 2 Read 15 3MB Write 4 7MB NOTE This function may result in data loss and format the Flash drive Only the destination ports can be measured 6 3 Media Check Analyze the Flash drive s quality There are two types of methods to check the drive H3 Safe and H5 R W Before
9. he power switch on the USBDUP15 is set to the off position b The source or destination drives can be replaced with any SD SDHC Micro SD MMC Mini SD CF media card using USB multimedia card reader sold separately or Hard Drive HDD Solid State Drive SSD through a Hard Drive docking station or USB enclosure sold separately 1 Insert the source USB flash drive you would like to copy into the Source USB drive port on the USBDUP15 2 Insert up to 5 destination USB flash drives that you would like to be over written with the same data that is currently on the source drive into the destination USB drive ports WARNING Any DATA on the destination USB Flash drives will be overwritten 3 Connect the power adapter port on the USBDUP15 to an available power source using the included Universal power adapter 4 Set the power switch on the USBDUP15 to the on position 5 The USBDUP15 is now is ready for operation as the user menu appears on the LCD display StarTechy om 3 Hard to find made easy Instruction Manual User Menu Table of Contents 1 Copy 2 Compare 3 Copy Compare 4 Capacity Check 5 Information 5 1 USB Info TE EE 6 Utility 6 1 Format 6 1 1 Auto Format bes FAT Format 6 1 3 FAT32 Format Measure Speed Media Check 6 3 1 H3 Sake 10096 6 3 2 H5 RW 10096 6 3 4 Setup Error Limit 4 Quick Erase Full Erase DoD Erase 7 System Update Calc Checksum 7 Setup 7 1 Start up Menu 7 2 Copy Area 7
10. i inima ie a Pa og ds 6 PA GR nec EE EE E m 7 3 COPY t COMPA asa Fade cen Eua Ra P CUR RAPI PDF n dc n LU CUR n E as 7 4 Capacity Check RES EE ED RD ee DE 8 SA io ig ie OE EE tansy E Oe 8 EEN dT EE DEE 9 6 2 Meas re Eed n Ee Ee GE DA EG ie 10 TAE E PC 11 Technical SUID DORE sus iese via vU RD Ri edi MER EX ee Dol ae duos ER GRA 14 Warranty Information sides Ne oii dd anderer 14 Starlechg om Instruction Manual i Hard to find made easy Product Diagram Top View Source USB drive port Destination USB drive ports LCD Display Forward button Backward button OK button Escape button Back View N Oo Ui BU N Ur 1 Power Adapter Port 2 Power Switch Starlechg om 1 Hard to find made easy Instruction Manual Introduction Packaging Contents 1x 1 5 USB Flash Drive Duplicator USBDUP15 1x Universal Power Adapter NA UK EU 1x Instruction manual System Requirements 1x Source USB drive 1 to 5x Destination USB drive s Optional USB multimedia card reader 1 x each drive To use an SD SDHC Micro SD MMC Mini SD CF card as Source or Destination drive Optional USB to SATA Hard Drive docking station USB to SATA enclosure To use a solid state drive SSD or hard drive HDD as Source or Destination drive Starlechg om 2 Hard to find made easy Instruction Manual Hardware Setup Note a Before you begin ensure t
11. ive has been plugged in StarTechy om 6 Hard to find made easy Instruction Manual 2 Once the copy has completed the green LED will stop blinking The destination Flash drive can be removed and a new Flash drive inserted then the copy will automatically start again The LCD display will show the accumulated quantity of the successful failed duplications and the drive that is still copying Quantity of copy pass and copy fail The quantity of flash media in process NOTE a When the copy is in progress the green LED will flash for each Flash drive that is connected When the copy has finished the green LED will stop flashing and remain illuminated If an error occurs the red LED will illuminate b Do NOT remove the Flash drive while the system is copying green LED is flashing C Once the copy process has completed green LED is solid you can then take out that Flash drive and insert a new one d During an Asynchronous copy you can press the up and down arrows to check each Flash drive s copy status and progress This works both during a copy green LED flashing and when there is an error red LED solid 2 Compare Check the Flash drive after a copy has completed to ensure the copy has completed successfully 3 Copy Compare Automatically compares the Flash drive once the copy has completed StarTechy om 7 Hard to find made easy Instruction Manual 4 Capacity Check Check the exact capacity
12. lly use asynchronous when copying If disabled the system will copy in synchronous mode This mode is enabled by default 7 7 Check before Copy Choose to enable or disable the system checking the Flash drive before starting a copy By default the drive is not checked before copying 7 8 Power off time between Copy Compare When performing the Copy Compare function set the wait time in seconds after a Copy has completed and before the Compare starts The default is 3 seconds 7 9 Language Change the system language between English and Japanese Starlechcom 12 Hard to find made easy Instruction Manual 7 10 Working Mode There are 5 duplication speeds Slowest Mode e Slower Mode e Normal Mode default setting Faster Mode Fastest Mode Change the duplication speed Normal speed is recommended for most Flash drive types If there is a high failure rate when duplicating try lowering the speed 7 11 Set HDD Mode Choose Active Mode to duplicate to USB Hard Disk Drives HDD SSD Choose Inactive Mode to duplicate USB Flash drives Inactive mode is set by default 7 12 Restore Default Restore the system back to factory defaults StarTechy om 13 Hard to find made easy Instruction Manual Technical Support StarTech com s lifetime technical support is an integral part of our commitment to provide industry leading solutions If you ever need help with your product visit www startech com support and acce
13. omise StarTech com is your one stop source for every connectivity part you need From the latest technology to legacy products and all the parts that bridge the old and new we can help you find the parts that connect your solutions We make it easy to locate the parts and we quickly deliver them wherever they need to go Just talk to one of our tech advisors or visit our website You ll be connected to the products you need in no time Visit www startech com for complete information on all StarTech com products and to access exclusive resources and time saving tools StarTech com is an ISO 9001 Registered manufacturer of connectivity and technology parts StarTech com was founded in 1985 and has operations in the United States Canada the United Kingdom and Taiwan servicing a worldwide market
14. ss our comprehensive selection of online tools documentation and downloads For the latest drivers software please visit www startech com downloads Warranty Information This product is backed by a two year warranty In addition StarTech com warrants its products against defects in materials and workmanship for the periods noted following the initial date of purchase During this period the products may be returned for repair or replacement with equivalent products at our discretion The warranty covers parts and labor costs only StarTech com does not warrant its products from defects or damages arising from misuse abuse alteration or normal wear and tear Limitation of Liability In no event shall the liability of StarTech com Ltd and StarTech com USA LLP or their officers directors employees or agents for any damages whether direct or indirect special punitive incidental consequential or otherwise loss of profits loss of business or any pecuniary loss arising out of or related to the use of the product exceed the actual price paid for the product Some states do not allow the exclusion or limitation of incidental or consequential damages If such laws apply the limitations or exclusions contained in this statement may not apply to you Starlechcom 14 Hard to find made easy Instruction Manual Starlechcom Hard to find made easy Hard to find made easy At StarTech com that isn t a slogan It s a pr
15. t different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Use of Trademarks Registered Trademarks and other Protected Names and Symbols This manual may make reference to trademarks registered trademarks and other protected names and or symbols of third party companies not related in any way to StarTech com Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech com or an endorsement of the product s to which this manual applies by the third party company in question Regardless of any direct acknowledgement elsewhere in the body of this document StarTech com hereby acknowledges that all trademarks registered trademarks service marks and other protected names and or symbols contained in this manual and related documents are the property of their respective holders StarTechy om Hard to find made easy Instruction Manual Table of Contents Product DidG raise TEE TT 1 lee ER OE EE EE EE EE NT HE NE 1 ble AE OE EE EE EO EE OE EE ene 1 edele ld leid ie AE N OE 2 Packaging ESE ES ee EE Ge DD 2 Ede Se Sie AREA ey eer OR Tere eer N EE EE acre eee 2 Hardware Setup esse SE aaa GO EUN D V EE 3 User Menu Table of COlIEGINES ak EE sea SE Re ee GE ee 4 Hardware Ope UGO ora du UV es NE ETE EQ oe Gee ee ee eg ATE ee ee E 5 12 ASyDCDEODOHS CODY es ee RE ee dauid andi te eti
Download Pdf Manuals
Related Search
Related Contents
Tu crèches où ? - Pierrefitte-sur 取扱説明書はこちら Metered Power Distribution Unit User Guide 名称未設定 2 VANNE A MANCHON JVC KD-AR200 Instruction Manual AGFA AC 8131D User's Manual Model VJP1 Pulse Repeater (Isolated Single-output 取扱説明書 (6.58 MB/PDF) Copyright © All rights reserved.
Failed to retrieve file