Chief K0W100B flat panel wall mount
Contents
1. Ibs 11 34 kg KOW100BXI2 2 lbs 0 9 kg KOW100BXI2TB 2 lbs 0 9 kg WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS Installation Instructions DIMENSIONS KOP100 POLE CLAM 1 50 1 9 KO Series P RANGE BEI 50 8 1 83 46 4 1 41 al INTERFACE AO TATION AANGE GI NO UN TING PATTE CON PA TIBILITY 100 X 100 15175 nm Pas OL TS LI 1 83 300 46 4 aj INTERFACE ROTATION RANGE 4 MOUNTING PATTERN COMPATIBILITY 100X100 15175 E 136 34 4 KO Series Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Ph2. adjustment may be locked by installing rotational locking screw M into back of faceplate See Figure 7 5 The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor See Figure 8 6 Use 3 16 hex key N to adjust rotational adjustment screw to adjust rotational tension See Figure 8 rotational tension pivot point tension Figure 8 Display Removal WARNING Only remove display from mount when the display can be lifted up from the mount DO NOT remove display unless the display is in the upright position See Figure 9 1 Make sure display is in the upright position 2 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 9 i Gi 74 quick release tab Figure 7 Figure 9 Installation Instructions KO Series KO Series Installation Instructions 10 Installation Instructions KO Series 11 KO Series Installation Instructions USA International CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002476 Rev01 2014 Milestone AV Technologies www chiefmfg com 04 14 pNUb5TNUD TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6
3. or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the KO Series Monitor Arm up to and including the display does not exceed the weight limits in the table below Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury MODEL Max Weight KOP100 25 Ibs 11 34 kg KOW100 25
4. 5mm screws C through corresponding holes on faceplate spacers D and into the mounting holes on the display See Figure 5 1 GY ici release lever Figure 3 for recessed mounting holes WARNING Only remove display from mount when the f p display can be lifted up from the mount DO NOT remove quick release E display unless the display is in the upright position See faceplate d Display Removal section for details 2 Carefully place display face down on protective surface 3 Connect faceplate to display For flush mounting hole installation e Using Phillips screwdriver carefully install four M4x14mm screws B through corresponding holes on faceplate and into the mounting holes on the display See Figure 4 Figure 5 KO Series Installation Instructions 4 Position display with faceplate attached above mount See Figure 6 5 Slide faceplate onto mounting head until quick release tab clicks into place See Figure 6 Figure 6 Adjustments Pitch Adjustment 1 Adjust pitch to desired tilt position See Figure 8 2 Adjust pitch tension screw to change the adjustment tension See Figure 8 Pivot Adjustment 3 Adjust pivot position as desired See Figure 8 4 Use 3 16 hex key N to adjust pivot point tension screws to change pivot adjustment tension See Figure 8 Rotational Adjustment NOTE Optional Rotational
5. 918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 I al d D 1 Yr consume
6. INSTALLATION INSTRUCTIONS KOW100BXI2 ROVV100BXI2TB Pitch Pivot Mount Series CHIEF KO Series Our Mounts Your Vision KO Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment
7. illips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a mao A mano Met de hand Ala main Optional Opcional Optional Opcional Opzionale Optie En option C d y 4 d Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale 2 0 HI DP Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranca Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions KO Series TOOLS REQUIRED FOR INSTALLATION e e 2 3 16 included 1 8 included 5 32 included with KOP Series only P 1 Pad6 interface iPad versions only K A 1 aa monitor arm or monitor arm KOP100 KOW100 B 4 Cu D 4 M4x14mm M4x25mm M10
8. x5 3x10 included with KOW Series wall mount only 4 12TB Interface I M e e el H 1 J 4 K 4 L 1 M 1 I pole clamp 1 4 20 x 1 1 2 1 4 20 x 1 5 32 10 24 x 1 4 N 1 P 1 3 16 1 8 KO Series Installation Instructions Assembly And Installation Figure 1 Connecting KOW Series wall mount to Wall 1 Determine mounting location on wall 2 Use a stud finder to locate 2 x 4 wood stud 3 Use wall bracket E to mark and drill two 1 8 x 2 1 2 holes in wall at desired mounting location See Figure 1 4 Use two 1 4 2 1 2 hex head lag screws F and two 1 4 washers G to install wall bracket E onto wall See Figure 1 IMPORTANT Over tightening screws F may cause bracket to compress into soft wall surface resulting in difficult mount installation or improper engaging of set screw in Step 6 5 Hang monitor arm A over wall bracket E See Figure 1 6 Secure monitor arm to wall bracket E by tightening set screw Ensure set screw engages back side of wall bracket E to properly secure mount See Figure 1 Connecting KOP Series to Pole 1 Determine approximate location for mount keeping in mind display size extension height adjustment requirements 2 Place mount A against pole with clamp H on opposite side of pole See Figure 2 KOP assembl
9. y Figure 2 Using 5 32 hex key L and appropriate length screws loosely attach KOP assembly to pole clamp H If installing to 1 1 2 NPT pipe use 1 4 20 x 1 1 2 button head cap screws J If installing to 1 1 2 diameter pipe use 1 4 20 x 1 button head cap screws K See Figure 2 Position mount at desired height and orientation Equally tighten screws against mount and the pole clamp Installation Instructions KO Series Display Installation for flush mounting holes WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the H ISCH installer s responsibility to make sure the combined weight of quick repasa all components attached to the KO Series Monitor Arm up to acep AE ED B x 4 and including the display does not exceed 25 lbs 11 34 kg Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury NOTE For ROVV100BXI2 mounts refer to FSBI2B installation instructions to install iPad to mounting arm 1 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 3 Figure 4 For recessed mounting hole installation e Place four spacers D on top of mounting holes on back of display See Figure 5 e Using Phillips screwdriver carefully install four M4x2
Download Pdf Manuals
Related Search