Bose SoundTouch SA-4
Contents
1. 3 8 in 9 5 mm minimum English 31 Appendices Appendix C Wall mounting the SoundTouch wireless adapter Vertical orientation Connector panel is facing left sa coo Horizontal orientation Connector panel is facing up Follow these instructions to wall mount your SoundTouch wireless adapter Install either vertically with the connector panel facing left or horizontally with the con nector panel facing up Note Mounting hardware must be purchased separately If the mounting hardware instructions differ from these instructions follow the mounting hardware instructions e Wood Mounting Mount to 1 in 25 4 mm or thicker wood Drill hole with a in 3 17 mm drill Use 2 8x174 in 32 mm pan head wood screws e Wallboard Mounting Mount to in 9 5 mm or thicker wallboard Drill pilot hole with a 3 16 in 4 76 mm drill Use 2 6 8x1 in 25 4 mm plastic wall anchors and 2 8x1 in 32 mm pan head wood screws Wood Wallboard in 6 35 mm 4 in 6 35 mm above surface N above surface NG Mark holes on the wall 6 in 158 7 mm center to center Drill holes Insert anchors if used Install screws Leave the screw heads in 6 35 mm above wall surface PO NE Position SoundTouch wireless adapter onto screws Press firmly into place 32 English Appendices Appendix D Using a desktop computer to conn2. ki HA NAKA ii Boselink SPEAKER OUTPUT OUTPUTS cd Gr ara SA 4 amplifier status indicator MAXIMUM ABC6789 Solid On and ready to receive data Slow blinking 1 sec on 3 sec off In standby Fast blinking On and receiving data English 19 Using the System SoundTouch wireless adapter Wi Fi status indicator The SoundTouch wireless adapter is powered by the SA 4 amplifier The Wi Fi status indicator is located on the back panel SoundTouch wireless adapter Wi Fi status indicator Blinking white Connecting to Wi Fi network Solid white System on and connected to Wi Fi network Solid amber System in setup mode page 12 and page 24 Blinking slow amber Disconnected from Wi Fi network Blinking fast amber Firmware error call Bose service Off Networking disabled or system connected to Ethernet 20 English Advanced Features Alternate setup method Using this method you can set up your SoundTouch system by first joining its own built in Wi Fi network and then connecting to your home Wi Fi network 1 On the back of the SoundTouch wireless adapter press and hold the Control button for 2 6 seconds 2 When the Wi Fi status indicator blinks amber once and lights solid amber release the Control button Wi Fi status indicator Control button 3 On your computer tablet or
3. Contact Bose customer service for assistance Note If part of the system is damaged do not use it Contact your authorized Bose dealer or Bose customer service Please refer to the contact list in the carton for contact information English 9 Setting up the System Adding the system to your Wi Fi network Tip A laptop is the preferred method for connecting to the network If you must use a desktop computer see Appendix D Using a desktop computer to connect to the network on page 33 Before you can use SoundTouch you must install the SoundTouch app onto a computer that is on your home network Next you will use the app to connect the system to the network The app guides you through the setup process Make sure you follow the instructions on your computer Note If you have already set up SoundTouch for another system just launch the app and click EXPLORE gt SETTINGS gt Systems gt ADD SYSTEM to add another system Installing the SoundTouch app 1 From a computer that is on your Wi Fi network open a browser and go to http www Bose com soundtouch_app Tip If you want SoundTouch to play your iTunes or Windows Media Player music library use the computer where your music library is stored http www Bose com soundtouch app aN 2 Download and install the SoundTouch app onto your computer You are now ready to connect the system to your network Note D
4. depending on the source Presets with the SoundTouch controller This section describes how to set and change a preset from the SoundTouch controller Presets ring Note For information on using the SoundTouch app to set and change your presets refer to the Help system in the app To set a preset 1 Stream music to the system using the app 2 While the music is playing press and hold a preset on the SoundTouch controller about 2 seconds A New Preset Assigned message appears on the screen To change a preset Follow the instructions in To set a preset English 23 Care and Maintenance Adding a Wi Fi network If your network information has changed or to connect your system to another network you must add the new network information in the app and then connect the system 1 Launch the SoundTouch app 2 Click EXPLORE gt SETTINGS gt Systems 3 Select the system 4 Click CONNECT TO A WI FI NETWORK 5 Follow the instructions on your computer Troubleshooting For more troubleshooting information refer to the Help system in the SoundTouch app Cannot complete e Make sure the SoundTouch wireless adapter is plugged into the network setup BoseLink INPUT connector and the SA 4 amplifier is connected to AC mains power e Ensure network name and password are correct e Ensure network service is available and system and computer are on the same network e Move system closer to
5. operating instructions for your unpowered speakers to connect the other end of the cables to the speakers Make sure to connect the marked wires to the positive terminals 6 Install the speakers in their permanent location 7 Reconnect the SA 4 amplifier to AC mains power Tip Use a silicone caulking material such as RTV adhesive to protect speaker wire connections It is commonly available at hardware stores Using the SoundTouch app The SoundTouch app is a software application that enables you to control the system from your computer smartphone or tablet Using the app your smart device acts as a rich remote for your SoundTouch system The app enables you to manage your system settings explore local and global Internet radio stations set and change presets stream music to the system view what is playing plus much more After you set up the system on your network using the SoundTouch app you are ready to explore streaming music and to personalize your presets Getting help If you need more information on using the system use Help Tips or Online help Help Tips After setup is complete helpful tips appear on the screen based on the task you are trying to complete These tips instruct you how to use the system including how to personalize your presets To activate the tips If you have deactivated tips follow these instructions to re activate tips 1 Launch the SoundTouch app and click EXPLORE gt SETTI
6. smartphone activate Wi Fi and join the Bose SoundTouch Wi Fi network Note It may take several moments for the network to appear on your device 4 Open a browser and type http 192 168 1 1 in the address field The Wi Fi setup window appears on the screen 5 Select your home Wi Fi network from the drop down list 6 Enter your password if required and tap or click Connect The SoundTouch wireless adapter Wi Fi status indicator blinks rapidly while the system connects to your home Wi Fi network 7 On your computer tablet or smartphone return to the Wi Fi control panel and rejoin your home Wi Fi network 8 Once the system is on the network follow these steps to complete setup A Download and launch the SoundTouch app B On the SOUNDTOUCH SYSTEM SETUP screen select this option IT IS ALREADY CONNECTED English 21 Advanced Features Disable enable Wi Fi capability The SoundTouch wireless adapter has built in Wi Fi capability that enables it to wirelessly connect to your home Wi Fi network The Wi Fi capability is disabled when the SoundTouch wireless adapter is placed in the Power Saving mode Power Saving mode The SoundTouch wireless adapter has a low power standby mode in which it consumes a minimum amount of power This can be used to reduce the power consumed in your home while you are away To place the SoundTouch wireless adapter in the Power Saving mode and disable the Wi Fi capabili
7. to the speaker on the right in your listening area Check the speaker cable connections Make sure the individual wires are connected to and to Interference Make sure the speaker cables are firmly inserted in the terminals on the back of the speakers and on the amplifier rear panel Check to be sure no individual wires are touching across terminals Make sure the SoundTouch wireless adapter is away from metal objects other audio video components and direct heat sources SoundTouch controller does not adjust the volume Volume suddenly decreases Replace the batteries in the SoundTouch controller If you are using a local volume control VCA turn it to the off position Lower the volume setting to see if the level returns to normal If so the sudden loss of volume was an intentional action of the ampli fier s overload protection feature This engages automatically if the volume is set too high and is overdriving the speakers Choosing a lower setting should ensure continuous even volume Disconnect the amplifier from AC mains power and allow it to cool Increase ventilation Reconnect to power If the volume level returns to normal the sudden loss of volume was an intentional action of the amplifier s thermal overload protective feature This engages automaticaly if the amplifier overheats Increasing ventila tion should ensure continuous even volume Wireless adapter does not awaken f
8. wireless router or network access point e Stop other audio or video streaming applications e Close app disconnect all cables and restart setup process Cannot connectto e If your network has changed or to connect your system to another network network see Adding a Wi Fi network on page 24 e Try connecting to the network using an Ethernet cable Intermittent or e Make sure the SoundTouch wireless adapter is plugged into the no audio from BoseLink INPUT connector SoundTouch e Move the SoundTouch wireless adapter away from possible interference such as microwaves cordless phones metal cabinets or other metal objects etc e Stop other audio or video streaming applications e Ensure system is powered and connected to the same network as the computer e Move system or audio source closer to wireless router or network access point e Ensure system volume is not muted or too low e Unplug the power cord reconnect after one minute Cannot hear an e Ensure system and AirPlay device are connected to the same AirPlay device network e Ensure AirPlay device is playing increase its volume e Ensure system is selected in the AirPlay menu of the device e Move AirPlay device away from possible interference and closer to the wireless router or network access point Note Proximity of the AirPlay device to the system is not important only to the wireless router or network access point 24 Engli
9. 1 7 nanana anasananaa nanana 18 Playing an Air Plays a amak 19 Status INGICALOMNS AA AA 19 SoundTouch SA 4 amplifier status indicator sanan eene 19 SoundTouch wireless adapter Wi Fi status indicator 20 Advanced Features Alternate setupimetho daa a RA aaa 21 Disable enable Wi Fi Capability cceceececeeceeeeeseeeceeeeeeeeceeeeeeeeeeeeeeeeeeeeeaees 22 Power Saving mode ARENA NAA 22 English 5 Contents Personalizing your Presets How Presets WOK ssiri ansaa isaer aE E aaRS 23 What VOU MEG to KMOW isrssiisissrcisi tastera aaiae 23 Playing a preset ncescinkads iin nna aan E E ENE 23 Presets with the SoundTouch controller nnaman iaraa 23 Toseta preset aaa Ana aati ane ae 23 TO change a pres bana ANAND A IKAN ham KG 23 Care and Maintenance Adding a Wi Fi networku aa aaa 24 Nde 0 23 Lo 2101 ARA AA AA 24 CIGARS maka AA AA E E GE ete ts 26 CUSLOME SEVICE aanak 26 Limited warranty Infarmati N u s NAKAKA aan 26 Technical Information SoundTouch SA 4 AMplifler cecceeeceeeecececeececeecesesceeesceeeceeaeceeeeeeteeeateeatens 27 SoundTouch wireless adapter ececeecceceeceeeceeeeceseeeeeaeceeeeeeaeceeeseeateeeeeeatees 28 SourdToueh controlled an ANAN 28 Appendices Appendix A SA 4 amplifier connector panel ssseeseeeeeeeeeeeeeeeeeees 29 Appendix B Wall mounting the SoundTouch SA 4 amplifier 30 Appendix C Wall m
10. 13 Bose Corporation No part of this work may be reproduced modified distributed or otherwise used without prior written permission 4 English Contents Introducing SoundTouch from Bose KGB GRC TICS issie RE a PAER iE E 7 Introduction About your SoundTouch SA 4 amplifier cesecececeeeeeeeeeeeeeeeeeeeeeeeeeeeees 8 SystemiteakUrE SA BANANA ANAND 8 Setting up the System Unpacking the SyS eee ute tees a a NAA ta 9 Adding the system to your Wi Fi NECWOFK c ececeseeeeeeeeeeeeeeeeeeteeeteees 10 Installing the SoundTouch ApP 2 c cesceeeceeeceeeeceeeceeeeeeeeeereaeeeneeeeaees 10 Connecting the system to your home Wi Fi network 2 0ee 11 Installing the SoundTouch SA 4 amplifier nana awnaaauwaaauwaw wawa nennen 13 Installing the SoundTouch wireless adaptel ceesceeeeseeeeees 13 Connecting speakers to the SA 4 amplifier ul mamamana wawan awan anna wananwanann 14 Controlling the System using the App Usine the Sound Touch app mananahan GN K GN eee eels 15 EYA AA AA AA AA 15 Downloading the app for your mobile device annnn nanan nanan nanana nanana 16 Controlling the system from another computer LL annna nanan wanna nanana 16 Using the System Playing music with the SoundTouch CONTIOIlEP ceeeeeceeeeeeeeeeeeeeeeees 17 Using the the SoundTouch controller eee nananana awawanawawwawanwananunana 17 Wall mounting the SoundTouch controller
11. AKER Status indicator OUTPUTS AC AC power cord connector Power is applied when the power cord is POWER inserted and plugged into an AC mains outlet There is no on off switch on the SoundTouch SA 4 amplifier VCA Local volume control connector Allows you to control the volume using a wall mounted control Contact your Bose dealer or call Bose customer service for information on installing this feature See the contact list enclosed in the carton SPEAKER Left and right speaker outputs Connect only unpowered speakers A OUTPUTS 6 ohm minimum load is required To determine the correct speaker wire size see Speaker cable recommendations on page 27 ROOM Only switch A is used for SoundTouch systems DE Se The output of the SoundTouch SA 4 amplifier can Switch B Down be set to stereo Switch A up or mono Switch A down The mono output mode feeds left and right Switch C Down channel audio to both the left and right outputs This Switch 6 Down is useful in situations where a stereo output isn t _ feasible such as when outdoor speakers are used in Switch 7 Down a large area Switch 8 Down The remaining six switches should remain in the f default configuration Switch9 Up Status The green indicator shows the operational state of the SA 4 amplifier indicator See SoundTouch SA 4 amplifier status indicator on page 19 BoseLink Used for connecting the SoundTouch wireless adapter to the INPUT SA 4
12. MUSE SF SoundTouch SA 4 amplifier Owner s Guide Safety Please take the time to follow the instructions in this owner s guide carefully It will help you set up and operate your system properly and enjoy its advanced features Please save this guide for future reference All Bose products must be used in accordance with local state federal and industry regulations AN RISK OF ELECTRICAL SHOCK AN DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electrical shock The exclamation point within an equilateral triangle as marked on the system is intended to alert the user to the presence of important operating and maintenance instructions in this owner s guide WARNINGS To reduce the risk of fire or electrical shock do not expose the product to rain or moisture Do not expose this apparatus to dripping or splashing Do not place objects filled with liquids such as vases on or near the apparatus As with any electronic products use care not to spill liquids into any part of the system Liquids can cause a failure and or a fire hazard e Keep battery or batteries away f
13. NGS gt Help Tips 2 Slide the SHOW TIPS slider to ON Online help For information about using SoundTouch 1 Click EXPLORE gt HELP in the app 2 Browse through the help topics English 15 Controlling the System using the App Downloading the app for your mobile device Bose offers a free mobile version of the SoundTouch app so you can control the system from your smartphone or tablet To install the app for your smartphone or tablet e For iOS users download the SoundTouch controller app from the App Store e For Android users download the SoundTouch controller app from the Google Play Store Controlling the system from another computer Once you set up the SoundTouch system on your home Wi Fi network you can control the system from any computer on the same network 1 On the computer where you want to control the system open a browser and go to http www Bose com soundtouch app 2 Download install and launch the SoundTouch app The sign in screen appears You are ready to sign in to your SoundTouch account 16 English Using the System Playing music with the SoundTouch controller During the app set up process the SoundTouch controller was activated and a wireless connection was established You can use the SoundTouch controller to play and manage your presets Note The SoundTouch controller must be within 70 feet 21 m of the SoundTouch wireless adapter in wood
14. al wiring or plumbing e The wireless adapter connects to the SA 4 amplifier with a 6 foot 1 8 m cable Place the SA 4 amplifier so that the wireless adapter is within range of your Wi Fi router or network access point e Place the SA 4 amplifier and wireless adapter in an area where the maximum ambient temperature is less than 104 F 40 C e For optimum performance place the SA 4 amplifier in a well ventilated area e DO NOT place the SA 4 amplifier in a completely enclosed area If adequate ventilation is not provided the amplifier automatically protects itself by reducing its volume level in order to limit its temperature e DO NOT place the SA 4 amplifier on any heat sensitive surface such as the finished surface of fine furniture Like all electrical equipment it generates some heat e DO NOT use the SA 4 amplifier in a damp location It is important to prevent moisture from getting into the system Installing the SoundTouch wireless adapter The SoundTouch wireless adapter provides the network input for the SA 4 amplifier It must remain in range of the Wi Fi router and within 70 feet 21 m of the SoundTouch controller To keep interference to a minimum and to increase the strength of the Wi Fi signal install the wireless adapter outside of and away from metal cabinets away from other audio video components and away from direct heat sources See page 32 for wall mounting instructions Note If you experie
15. amplifier BoseLink Not used OUTPUT English 29 Appendices Appendix B Wall mounting the SoundTouch SA 4 amplifier Vertical cg R orientation Oa Connector panel is facing left Horizontal orientation Connector panel is facing up anne Follow these instructions to wall mount your SoundTouch SA 4 amplifier Install either vertically with the connector panel facing left or horizontally with the connector panel facing up 1 Remove rubber feet from the SA 4 amplifier Use these holes to mount the amplifier on the wall 2 To mark mounting hole locations hold the SA 4 amplifier in position and mark the wall through the holes in the housing 3 Drill holes 4 Insert and tighten screws and anchors if used 30 English Note Mounting hardware must be purchased separately If the mounting Appendices hardware instructions differ from these instructions follow the mounting hardware instructions e Wood Mounting Mount to 1 in 25 4 mm or thicker wood Drill pilot hole with a 3 32 in 2 38 mm drill Use 4 10 x 1 in M5 x 38 mm pan head wood screws e Wallboard Mounting Mount to in 9 5 mm or thicker wallboard Drill pilot hole with a 72 in 12 7 mm drill Use 4 10 x 2 in M5 x 63 5 mm pan head machine screws and 4 10 M5 spring anchors Wood lt gt 1 in 25 4 mm minimum Wallboard
16. construction homes In concrete stucco or brick homes the range will likely be less and may vary The number of other active wireless devices in the home may affect range Ideally there should be no more than one wall or ceiling between the controller and the wireless adapter SoundTouch icon Presets ring Skip backward Skip forward Screen Volume ring Using the SoundTouch controller e Press a preset to play it Press and hold a preset to personalize it e Move your finger around the Presets ring to view presets e Turn the Volume ring to adjust the volume e Touch 44 or PP to skip through content e Press and hold the screen to turn the SoundTouch system on and off e Press the screen to play or pause music e Touch and hold the SoundTouch icon to disconnect the controller from a system To connect to another system refer to the help system in the app Note If the controller is in power saving mode wave your hand within 6 in 15 cm above the screen to turn it on English 17 Using the System Wall mounting the SoundTouch controller AN WARNING The wall mount bracket contains magnetic material Please contact your physician if you have any questions whether this might affect the operation of your implantable medical device Follow these instructions to wall mount your SoundTouch controller Use the bracket as a template to mark the holes Bracket Wallboard anchors and screws supp
17. d from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Use only attachments accessories specified by the manufacturer 12 Unplug this apparatus during lightning storms or when unused for long periods of time 13 Refer all servicing to qualified personnel Servicing is required when the apparatus has been damaged in a way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped ON Soe O N Important USA and Canada compliance Information This device complies with part 15 of the FCC rules and Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device complies with FCC and Industry Canada RF radiation exposure limits set forth for general population This device must not be co located or be operating in conjunction with any other antennas or transmitters This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 This device may not cause interference and 2 this device must accept any interference including interf
18. e disconnect device such disconnect device shall remain readily operable e The product label is located on the bottom of the product e The speaker wire and interconnect cables included with the system are not approved for in wall installation Please check your local building codes for the correct type of wire and cable required for in wall installation Changes or modifications not expressly approved by Bose Corporation could void the user s authority to operate this equipment Operate this product within the temperature range of 32 F to 104 F 0 C to 40 2 English Safety Important Safety Instructions 1 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water or moisture Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cor
19. ect to the network If you have a desktop computer temporarily move the SA 4 amplifier near the computer to set up the network connection The diagram below shows how to temporarily set up your SA 4 amplifier and SoundTouch wireless adapter near your desktop computer Once you have the components in place follow the procedures in this guide to connect to your network using the desktop computer After making the network connection you can test the system to make sure everything works When you are done disconnect the amplifier from your computer and AC mains power and permanently install the SA 4 amplifier When you reconnect the system to AC mains power it reconnects to your network See Installing the SoundTouch SA 4 amplifier on page 13 USB cable Note Connect the USB cable to the SoundTouch wireless adapter only when the app instructs you to do so English 33 Better sound through research 2013 Bose Corporation The Mountain Framingham MA 01701 9168 USA AM625304 Rev 00 625304 0010
20. erence that may cause undesired operation This equipment complies with FCC and Industry Canada radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 8 inches 20 cm between radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter CAN ICES 3 B NMB 3 B This Class B digital apparatus complies with Canadian ICES 003 Information about products that generate electrical noise This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harm ful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an
21. lied 1 Use a 3 6 in 5 mm drill bit to drill two holes into 3 s in 9 5 mm or thicker wallboard 2 Insert the provided anchors into the holes and tap lightly to secure 3 Align the bracket tab at top to the anchors Tighten the provided screws into the holes 4 Align the latch to the bracket s tab Attach the controller Wood 1 Purchase two 6x1 in 25 4 mm flat head wood screws 2 Usea 7 ea in 2 78 mm drill bit to drill 2 holes into 3 4 in 19 mm or thicker wood 3 Align the bracket tab at top to the holes Tighten the screws into the holes 4 Align the latch to the bracket s tab Attach the controller 18 English Using the System Playing an AirPlay stream In addition to playing content from Internet radio music services and your music library you can also stream audio from an AirPlay device on the same Wi Fi network 1 Start a music app on your AirPlay device Tip Adjust the volume on the AirPlay device to 75 percent of maximum to ensure optimal volume control from the SA 4 amplifier system 2 On the device tap or click Lal and select the SoundTouch system name assigned during setup 3 Start playing music from a music app Note To set up your system as an AirPlay device only see Alternate setup method on page 24 Status indicators SoundTouch SA 4 amplifier status indicator The SoundTouch SA 4 amplifier has a green status indicator on the connector panel
22. ller serial and model numbers Purchase date We suggest you keep your receipt with this owner s guide Made for GliPod HiPhone UiPad AirPlay AirPlay works with Apple iPhone iPad and iPod touch with iOS 4 3 3 or later Mac with OS X Mountain Lion and Mac and PC with iTunes 10 2 2 or later AirPlay Apple iPad iPhone iPod touch iTunes Mac and OS X are trademarks of Apple Inc registered in the U S and other countries Made for iPod Made for iPhone and Made for iPad mean that an electronic accessory has been designed to connect specifically to iPod iPhone or iPad respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod iPhone or iPad may affect wireless performance The Bluetooth word mark and logos are registered trademarks of Bluetooth SIG Inc and any use of such marks by Bose is under license Android and Google Play are trademarks of Google Inc SoundTouch and the wireless note design are trademarks of Bose Corporation in the U S and other countries Wi Fi is a registered mark of the Wi Fi Alliance Windows is a registered trademark of Microsoft Corporation in the United States and other countries 20
23. nce interference with your network connection place the SoundTouch wireless adapter outside of any cabinet or enclosure and away from metal objects If problems persist see Troubleshooting on page 24 English 13 Setting up the System Connecting speakers to the SA 4 amplifier CAUTIONS e Use only unpowered speakers DO NOT connect any make or model of powered speakers Doing so may cause damage to the equipment e The SoundTouch SA 4 amplifier requires a 6 ohm minimum load Speaker cables consist of two insulated wires Often one wire is marked striped colored or ribbed indicating it should be connected to the positive terminal The plain wire should be connected to the negative terminal For recommended wire sizes and lengths see Speaker cable recommendations on page 27 1 2 3 4 Disconnect the SA 4 amplifier from AC mains power Remove the terminal block connector from the SPEAKER OUTPUTS connector on the rear panel of the SA 4 amplifier Use a small flat head screwdriver to connect the left speaker cable to the L positive and minus terminals of the 4 pin terminal block connector and the right speaker cable to the R positive and minus terminals Bose 251 Environmental Speakers shown for illustration only Plug the terminal block connector into the SPEAKER OUTPUTS connector 14 English Controlling the System using the App 5 Follow the
24. o not connect any cables to the system until the app instructs you to connect the cables 10 English Setting up the System Connecting the system to your home Wi Fi network 1 4 5 Launch the app by double clicking the SoundTouch app icon The first time the app launches it guides you through setting up the system on your Wi Fi network The app instructs you to connect the system Place the SA 4 amplifier on a sturdy surface close to an AC mains power source Connect the wireless adapter to the BoseLink INPUT connector on the back of the SA 4 amplifier When prompted by the app plug the power cord into the AC POWER connector on the back of the SoundTouch SA 4 amplifier Plug the other end of the power cord into AC mains power English 11 Setting up the System 6 When prompted by the app plug the small end of the USB cable into the SETUP A connector on the SoundTouch wireless adapter SoundTouch wireless adapter SETUP A connector 7 Plug the larger end of the USB cable into a USB port on your computer When the SoundTouch app detects your system the Wi Fi status indicator on the rear panel of the SoundTouch wireless adapter lights solid amber The app instructs you to enter your network credentials 8 When prompted to remove the USB cable disconnect the USB cable from the SoundTouch wireless adapter and from the computer Note Leave the wireless adapter c
25. onnected to the SA 4 amplifier and the amplifier connected to AC mains power 9 Follow the instructions on your computer to complete setup including creating a SoundTouch account locating your music library signing in to music services exploring music and personalizing your presets Note During this process you will be prompted to install the provided batteries into the SoundTouch controller 10 When finished disconnect the SA 4 amplifier from AC mains power and prepare to connect the speakers If the amplifier is not in its permanent location install the SA 4 amplifier and the SoundTouch wireless adapter When you reconnect the system to AC mains power it reconnects to your network 12 English Setting up the System Installing the SoundTouch SA 4 amplifier Locate the SA 4 amplifier indoors close to an AC mains power outlet It does not need to be close to your speakers The SoundTouch SA 4 amplifier weighs 11 Ibs 5 kg It can be placed on a floor on a shelf or mounted on a wall See page 30 for wall mounting instructions Consider the following caution statements when selecting a location for your SA 4 amplifier CAUTIONS e The SA 4 amplifier must be used indoors It is neither designed nor tested for use outdoors in recreational vehicles or on boats e DO NOT mount the SA 4 amplifier on a surface that is not sturdy enough or that has hazards concealed behind it such as electric
26. ounting the SoundTouch wireless adapter 32 Appendix D Using a desktop computer to connect to the network 33 6 English Introducing SoundTouch from Bose With SoundTouch you can stream Internet radio music services and your music library If you have Wi Fi at home you re ready to enjoy your favorite music in any room or outdoor space that you want Key Benefits e Enjoy wireless access to Internet radio music services and your music library e Stream your favorite music easily with personalized presets e Works with your existing home Wi Fi network e Free SoundTouch app for your computer smartphone or tablet provides more powerful control e Simply add additional systems at any time for a multi room listening experience e Wide selection of Bose audio systems lets you choose the right solution for any room or outdoor space English 7 Introduction About your SoundTouch SA 4 amplifier The SoundTouch SA 4 amplifier is an elegant way to deliver high quality sound into any room or outdoor space streamed wirelessly over your home Wi Fi network Use the free SoundTouch app to set up and control your system See Adding the system to your Wi Fi network on page 10 System features e Easily connects to your choice of speakers for powerful sound anywhere around your home even connects to outdoor speakers Although the amplifier itself must remain inside and dr
27. outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help other relevant provisions of Directive 1999 5 EC and all other applicable EU directive requirements The C Bose Corporation hereby declares that this product is in compliance with the essential requirements and complete Declaration of Conformity can be found at www Bose com compliance English 3 Safety Names and Contents of Toxic or Hazardous Substances or Elements Toxic or Hazardous Substances and Elements Part Name Lead Mercury Cadmium Hexavalent Polybrominated _ Polybrominated Pb Hg Cd CR VI Biphenyl PBB diphenylether PBDE PCBs X 0 0 o 0 0 Metal parts X o o O O O Plastic parts 0 o Q O O O Speakers X O 0 O O ie Cables X 0 0 o 0 0 O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ T 11363 2006 X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T 11363 2006 Please complete and retain for your records The serial and model numbers can be found on the bottom of the system SA 4 amplifier serial and model numbers Wireless adapter serial and model numbers SoundTouch contro
28. rom children May cause a fire or chemical burn if mishandled Do not recharge disassemble heat above 212 F 100 C or incinerate Dispose of used batteries promptly Replace only with a battery of the correct type and model number Danger of explosion if battery or batteries is incorrectly replaced Use only AA batteries IEC LR06 Do not place any naked flame sources such as lighted candles on or near the apparatus KI WARNING Contains small parts which may be a choking hazard Not suitable for children under age 3 a WARNING This product contains magnetic material Please contact your physician if you have any questions on whether this might affect the operation of your implantable medical device K F3 Please dispose of used batteries properly following any local regulations Do not incinerate CAUTIONS To prevent electric shock match the wide blade of the line cord plug to the wide slot of the AC mains receptacle Insert the plug fully into the receptacle The product must be used indoors It is neither designed nor tested for use outdoors in recreation vehicles or on boats Make no modifications to the system or accessories Unauthorized alterations may compromise safety regulatory compliance and system performance NOTES A personal computer is required for system setup A home Wi Fi network and Internet access are required Where the mains plug or appliance coupler is used as th
29. rom power saving mode Disconnect the SoundTouch wireless adapter cable from the amplifier Disconnect AC power from the SA 4 amplifier for three minutes Reconnect the SoundTouch wireless adapter Reconnect power to the SA 4 amplier English 25 Care and Maintenance Cleaning CAUTION Disconnect the power cord from the AC mains power outlet before cleaning To clean the SA 4 amplifier use only a soft dry cloth to remove dust from the outside of the enclosure You may use a brush attachment on a vacuum cleaner to clean the hard to reach areas DO NOT use any solvents chemicals or cleaning solutions containing alcohol ammonia or abrasives Customer service For additional help using the system contact Bose customer service See the address and phone number list included with your SoundTouch system Limited warranty information Your SoundTouch system is covered by a limited warranty Details of the limited warranty are provided on the product registration card that is included in the carton Please refer to the card for instructions on how to obtain warranty service and register your product Failure to register will not affect your limited warranty rights 26 English Technical Information SoundTouch SA 4 Amplifier Features e Bose proprietary digital signal processing technology e Built in digital volume control e Thermal overload protection Dimensions and Weight e 14 in wide
30. sh Care and Maintenance Neither speaker plays Make sure the amplifier is connected to AC mains power Make sure the plug is inserted fully and the AC mains power outlet is powered Make sure content is selected via the SoundTouch app Disconnect the SoundTouch wireless adapter cable from the amplifier Disconnect AC power from the SA 4 amplifier for three minutes Reconnect the SoundTouch wireless adapter Reconnect power to the SA 4 amplifier Only one speaker plays Make sure the cables are in good condition and are firmly connected at both ends for the speaker that does not play One speaker still does not play Try connecting the speaker that does not play to the other speaker cable If the speaker still does not play the problem may be with the speaker If the speaker now plays you know the speaker and the cable are both good Disconnect the cable from the ampli fier terminal and connect it to the other terminal connector If the speaker now plays the problem is likely in the other speaker cable Replace it If the speaker does not play the problem may be in that channel of the amplifier Right and left stereo channels are heard on the wrong speakers Bass or treble is weak Make sure the cable connected to the SPEAKER OUTPUTS L at the amplifier are connected to the speaker on the left in your listening area and the cable connected to the SPEAKER OUTPUTS R at the amplifier are connected
31. ty press and hold the Control button on the back of the SoundTouch wireless adapter for 6 10 seconds When the Wi Fi status indicator turns off release the Control button To wake up the SoundTouch wireless adapter and enable the Wi Fi capability again press and release the Control button The Wi Fi status indicator blinks white as it reconnects to the Wi Fi network 22 English Personalizing your Presets How presets work You can personalize six presets to your favorite streaming music services stations playlists artists albums or songs from your music library You can access your music at any time with a simple touch of a button on the SoundTouch controller Tip You can also access your presets using the SoundTouch app on your computer smartphone or tablet See Using the SoundTouch app on page 15 What you need to know e You can set presets from the app or from the SoundTouch controller e f the preset source is your iTunes or Windows Media Player music library ensure the computer storing your music library is on and connected to the same network as the SoundTouch system Playing a preset Once you personalize your presets using the app press a preset on the SoundTouch controller to play it If you have not set your presets launch the app and set your presets For help refer to the Help system in the app Information appears on the screen which may include an icon song or station
32. x 572 in deep x 4 in high 36 2 cm x 14 0 cm x 10 8 cm e 11 0 Ib 5 kg Power rating e USA Canada 120V V 60 Hz 400W e International 220 240V 50 60 Hz 400W Input sensitivity 0 5 Vrms 1 kHz Signal to Noise ratio S N 90 dB Output power continuous average 100W channel minimum into 6 ohms from 30 to 15 kHz with no more than 0 5 THD Temperature range 32 F to 104 F 0 C to 40 C Speaker cable recommendations Maximum Length l Gauge 30 ft 9 m 18 0 82 mm 45 ft 14 m 16 1 3 mm 70 ft 21 m 14 2 0 mm English 27 Technical Information SoundTouch wireless adapter Dimensions and weight e 2 in wide x 9 in long x 2 in high 6 4 cm x 23 8 cm x 5 1 cm e 12 0 oz 34 kg Temperature range 32 F to 104 F 0 C to 40 C SoundTouch controller Dimensions and weight e 4 in diameter x 1 in high 10 5 cm x 2 8 cm e 8 0 oz 23 kg Temperature range 32 F to 104 F 0 C to 40 C 28 English Appendices Appendix A SA 4 amplifier connector panel AC POWER VCA ROOM CODE switches 00i SPEAKER OUTPUTS o BoseLink OUTPUT connector TTR Vea ltt ROOM CODE ABC6789 Is MAXIMUM cain 2205 BoseLink INPUT connector CO EE EE PT H Lf SPE
33. y e Bose patented signal processing automatically adjusts the tonal balance enabling full rich lows at nearly all listening levels e SoundTouch controller provides control from up to 70 feet 21 m away e Six presets deliver your music with just one touch e An Ethernet connector enables wired access to your home network e Stream your music via AirPlay for your Apple devices e USB connectors for network setup the USB connectors on the back of the system SETUP A and SETUP B are for setup only The connectors are not designed to charge smartphones tablets or similar devices 8 English Setting up the System Unpacking the system Carefully unpack the carton and confirm that the following parts are included Note Do not connect any cables to the system until after you have launched the SoundTouch app See Connecting the system to your home Wi Fi network on page 11 SoundTouch SoundTouch USB cable SA 4 amplifier wireless adapter P EO i AC mains power cord SoundTouch controller Save the carton and packing materials for transporting or storing the system CAUTION To avoid danger of suffocation keep the plastic bags out of the reach of children 0 The SoundTouch SA 4 amplifier includes the appropriate AC mains power cord for your region Use only the supplied AC mains power cord If it does not fit your AC power mains outlet DO NOT alter the plug in any way
Download Pdf Manuals
Related Search