Telewell TW-LTE/4G Wlan
Contents
1. Enable or Disable gt DHCP IP Pool Set a range of IP addresses available to access gt DHCP Lease Time Amount of time that a WIFl enabled device can use its assigned IP address before it is required to renew the lease gt DNS Mode You can choose to Auto or Manual Static DHCP With DHCP IP addresses are assigned dynamically devices typically don t have a permanent IP address But sometimes you may want to assign a static IP address to a device while still using DHCP for the rest of the devices on your network gt Hostname the name of the device that you want to assign IP Address to gt MAC Address the MAC Address of the device that you want to assign IP Address to gt IP Address input the permanent IP Address that you want to assign to the device You can determine to enable it or not and can also add new client and edit or delete existing ones IP Filter IP filtering is used to control specific IP addresses to access gt Select No Filtering to disable this function gt Select Block all in the list to deny IP addresses that you have set in the IP filtering list to access You can select to add new configuration in the list no more than 10 edit or delete exist ones URL Filtering URL filtering is used to control devices on the LAN access to specific URLs gt Select No Filtering to disable this function gt Select Block all in the list to deny all devices in the LAN to2. Open Lower security Works with older and newer WIFI devices Recommended only if your devices don t support WPA or WPA2 Open WEP uses the key only for encryption 13 ASCII characters or 26 digit HEX number needed WPA Personal TKIP A strong security standard supported by most WIFI devices 8 to 63 ASCII characters needed WPA Personal TKIP AES A strong security standard supported by most WIFI devices 8 to 63 ASCII characters needed WPA2 Personal AES A stronger newer security standard Limited to newer WIFI devices 8 to 63 ASCII characters needed gt WPA2 Personal TKIP AES A stronger newer security standard Limited to newer WIFI devices 8 to 63 ASCII characters needed gt WPA WPA2 Personal WIFI devices that use either WPA or WPA2 can connect to the device Supported by most WIFI devices 8 to 63 ASCII characters needed The length of your WIFI password depends on the type that you ve selected MAC filtering gt MAC Filter MAC filtering is used to control specific MAC addresses to access You can choose to Enable or Disable MAC Filter Mode Allow all in list Only devices in this list are allowed to access the network Block all in list All terminal devices are allowed to access the network except ones in this list MAC Filter List MAC Address display You can select to add new configuration in the list no more than 10 edit or delete exist ones VVV WV WPS gt WPS WIFI Protecte
3. access the URLs that you have set in the URL filtering list You can select to add new configuration in the list no more than 10 edit or delete exist ones Port Forward Port Forward is used to forward incoming traffic to specific ports or Internet addresses on your network Port Trigger In computer network an application makes connection to external computer by use specific port trigger port router forward external connection to internal port as you specified trigger port Device List The Device List lists the information about the device in the LAN including IP address host name MAC address and connect mode 9 5 Service Sharing You can view the status information of SD card while browsing the local file and create folders Only for a transfering of small files Upload a single file to the current directory of SD card because the browser limitations file name and share path does not exceed 150 characters Maximum size of uploaded file is 1 9G 9 6 System System set gt Change Password Input the new password confirm it and click Save to finish the settings gt Change Settings You can set the function of System work mode Standby timer on Battery and turn Off Backlight Config Reset Click Reset to reset the configuration to the factory settings Backup Settings Click Backup to back up the configuration file to the local PC Restore Settings Click Restore to restore the settings
4. from the configuration file backed up in the local PC Firmware Update Click Update to through the local upgrade software version Log gt Click Download to download the log information to the local PC gt Click Clear to delete all the log information gt Click Refresh to update the log information CE Declaration of Conformity https www telewell fi files declaration_of conformity_tw_Ite_wlan pdf
5. TW LTE 4G Wlan User Guide Copyright TeleWell Oy 1 Overview The device provides a simple way to use 4G connect to the Internet with any WIFl enabled device and to fulfill needs of sharing your internet connection during outside home 1 1 Introduction Indicator Description Pe 6 LCD screen Displays current status of the device USB interface Connect the USB cable to power adapter or PC Laptop Networking buttons Connect Disconnect Internet access WPS WiFi button a long press 5 seconds to turn on off WiFi b abort press less than 2 seconds to open the WPS PBC mode Power button a Long press 5 seconds to start on off the device b Sleep mode short press less than 2 seconds to exit sleep c Equipment work properly and the LCD screen backlight is turned on display SSID number and WiFi password short press less than 2 seconds Reset button a Short press less than 2 seconds equipment to restart b Long press more than 5 seconds to restore the factory settings SIM card installation instruction gt Open the back cover remove the battery 1 2 LCD Specification Category Icon Display Signal Strength E EM EA ESA i No WIFI user Battery level from critical to fully charged Micro SD card detected Micro SD card error Micro SD card Micro SD card not detected USB Status Equipment connected to the power adapter or use the USB connection to PC 1 3 Syste
6. You can choose to Enable or Disable gt Max Number of Users Set the maximum number of WIFI users If your network has problems you may want to decrease the number of WIFI users allowed to connect to the device The default value is 10 Security This part helps you configure the security of the wireless network Select an encryption mode in the list and set your password If you select None any WIFl enabled device can connect with the WLAN without the password gt gt None Not security It is not recommended since anyone can access your device and use your internet connection WEP 64 Bit Shared Lower security Works with older and newer WIFI devices Recommended only if your devices don t support WPA or WPA2 Shared WEP uses the same key for encryption and authentication which is considered to be less secure than open WEP 5 ASCII characters or 10 digit HEX number needed WEP 128 Bit Shared Lower security Works with older and newer WIFI devices Recommended only if your devices don t support WPA or WPA2 Shared WEP uses the same key for encryption and authentication which is considered to be less secure than open WEP 13 ASCII characters or 26 digit HEX number needed WEP 64 Bit Open Lower security Works with older and newer WIFI devices Recommended only if your devices don t support WPA or WPA2 Open WEP uses the key only for encryption 5 ASCII characters or 10 digit HEX number needed WEP 128 Bit
7. age will be automatically redirected to Homepage and need you to re login for further changes Shutdown the device Hold the power button over 5 second when the device is powered on the device will automatically shutdown 2 3 Battery charging and using time Battery can be charged using USB cable via PC or power adapter Battery charging time is about two hours Battery using time in LTE mode is upto 8 hours and in 3G mode upto 10 hours 3 Description for Client Interface 3 1 Activate Client Open the browser and then enter the IP address http 192 168 0 1 device interface will open in your browser Note If the user enters the IP address can t open the device software interface double click the shortcut icon the desktop client to re enter the IP address in the browser and refresh the page 3 2 Introduction to Interface The left hand menu 2 Registration Settings menu expand Status Information The status information displayed by client is as follows Statue information Description ome TEL UE Connected sia Unconnected Connection Status gis Connected OS Unconnected GPRS Connected S GPRS Unconnected a G Me Roaming On on e A SD Error Micso SD Card SD Card not detected bn Eos SD Enabled Battery oH i i Display WIFI SSID WIFI users WIFI security type channel WIFI MAC Others IP address gateway ONS IMEI boot time statistics and other relevant data Informatio
8. d Setup provide a more intuitive way of wireless configuration between your device and the wireless client Please make sure that the WIFl enabled devices you want to connect support this function Enable WPS firstly before you want to use it If you select the PIN way input the clients PIN to the Client PIN frame If you select the PBC way press the WPS button on wireless device in 120 seconds to establish WPS connection after you have pressed the WIFI WPS button on your device or clicked Save Click Save to save your settings and start connecting when you select PIN or PBC way You can also choose No Connection and click Save to save your settings without connecting 9 4 Router Basic gt UPnP You can choose to Enable or Disable gt L2TP Pass Through You can choose to Enable or Disable gt PPTP Pass Through You can choose to Enable or Disable gt IPSec Pass Through You can choose to Enable or Disable LAN This part helps you set your internal network for the device which contains Router IP Address Subnet Mask DHCP Server DHCP IP Pool and DHCP Lease Time gt IP Address The router s IP address on the LAN The default setting is 192 168 0 1 gt Subnet Mask The router s internal LAN subnet mask The default setting is 255 255 255 0 gt DHCP Server DHCP Server will automatically assign IP addresses to devices on the network You can choose to
9. m Requirements Operating System Windows XP 64bit 32bit SP3 Vista 64bit 32bit SP2 Windows7 64bit 32bit SP1 Windows 8 Mac x 10 5 or higher but not higher than x 10 8 0 Linux only Wlan Browser Internet Explorer Safari Network 2G 3G 4G LTE 2 Equipment installation 2 1 Connect the Device Before you want to use the device setup your device as following 1 Insert SIM 2 Insert Micro SD Card 3 Insert the battery 4 Hold the Power Connect button to power on 5 Connect this device to your terminal device Laptop 2 Laptop A Laptop 3 Q R The device applications scenes Figure PC devices can be connected via USB or via WIFI network Micro SD card inside the device provides network storage sharing function Note If the computer does not have a CDROM auto run function when the device is connected to the computer via USB and install the drivers please click on the My Computer to open the CDROM and manually install the driver If automatic installation failed please check whether the antivirus and security software is working If it is close it and reinstall 2 2 Startup Power up the device After all installation is complete Press and hold the power button over 5 second to power up the device Restart the device Some configurations may take effect after system reboot The device will reboot automatically once these configurations to be modified After reboot the webp
10. n 4 Registration User login interface When you click the left icone will pop up the login screen enter your password click OK landing completed Note The default user name and password admin and admin 5 Connection Network connection When you click on the con the software will automatically log on to the network Click again to disconnect from the network Note Make sure you have inserted the SIM card Operational Instruction for PIN If the user activates PIN under the setting menu it shall be required to input the correct PIN while using the application procedure totally 3 times to input PIN if the number is wrongly input after 3 times thus PUK should be used to decode the PIN and the input of PUK is only 10 times if the number is wrongly input after 10 times SIM will be locked or damaged Please contact the local operator for settlement SIM is provided by the network operator Please contact the operator for more information 6 Application App list Network service providers to provide application interface Application a list of items click on the application can perform 7 Application list Users can add commonly Website URL shortcut icons can be generated in the client 8 Theme The user can select the background image of the client experience a new visual experience 9 Settings Advanced settings help you to View Help Wan configure WIFI Router and System Afte
11. nutes two dialing mode PIN You can lock the SIM with PIN to protect the device against unauthorized use and unlock it The default PIN and PUK are provided by the operator or service provider The current PIN status and the rest chances to input PIN and PUK are displayed in this page The old PIN is needed if you want to unlock SIM or set a new PIN Select Lock and click Save button when you don t want to use the PIN Note The PUK an 8 digit code is required when PIN is input incorrectly 3 times If the PUK is wrongly input for continuously 10 times the card will be damaged Please contact the network service provider for details 9 3 WIFI Basic gt SSID Switch You can choose to Enable or Disable gt Wireless Interface There are different options when you select different Wireless Interface 802 11b Only 802 11g Only 802 11b g 802 11b g n gt Regulatory Domain Select the domain for the WIFI access point gt WIFI Channel Different domain has different channels gt Beacon interval Beacon interval is the frequency of broadcast packets from the device which is used to synchronize wireless networks Set lower value for finding and connecting to the device fast when higher value helps to save power SSID gt SSID This name is visible to other WIFl enabled devices and is used to identify your WIFI network The length of the SSID must be 1 32 characters long including _ gt Broadcast
12. r making some modification you should click Save to save all the settings or you can select Cancel to give up the modification 9 1 Help Here you can access the software help files 9 2 Wan APN Profile This page shows the APN list And in the profile list you will see the default and other APN configuration An APN Access Point Name is a reference to the Internet access point on Different APN for the 2G and 3G networks may be required You can select other APN as default edit or delete exist ones or create a new APN configuration no more than 10 in the list Set the Profile Name APN User Name Password and Network Mode and select Auth Type when you want to create a new APN profile Note only input what you have received from your service provider and leave other fields empty Net Search The default Network Selection mode is Automatic When click Manual a network list will be activated containing all searched networks Having selected an available network from the list LTE MiFi will register to the selected network Net Mode This page you can set up you prefer network connection mode gt Network Mode Network connection mode respectively Automatic 2G only 3G only LTE only gt Roaming You can choose to turn on or off the roaming function gt Connect Mode You can choose automatic or manual network connection gt Dial Mode You can select Keep Alive or Dial Demand 5 mi
Download Pdf Manuals
Related Search