Home

iRobot Braava 380t

image

Contents

1. Likely Cause Meijer com What To Do Braava Cleans only a small area Braava is not driving properly Cube not being used Cleaning cloth application Problem with wheels or treads Wheels slipping Make sure the Cube is turned on and placed in the area you want to clean Check the position of the Cube for interference such as e Cabinets shelves or ceiling fans above the Cube e Very high uneven or black ceilings above the Cube e Plasma or LCD televisions within 5 feet of Cube Remove and reapply cleaning cloth When reapplying follow these instructions e Ensure cloth does not overlap into the middle channel of the removable cleaning pad e Ensure cloth is not bunching up which can prevent the removable pad from reattaching completely to the robot Check wheel area for debris and remove or clean as needed Examine tire treads to make sure they are securely attached to the wheel If not well attached contact Customer Support Clean wheels with a cloth dampened with warm water to remove dust and cleaning solution Let the wheels dry before cleaning again Cleaning cloth application Problem with wheels or treads Remove and reapply cleaning cloth When reapplying follow these instructions e Ensure cloth does not overlap into the middle channel of the removable cleaning pad e Ensure cloth is not bunching up which can prevent the removable pad from reattaching completely to the robot e
2. charging while Braava is plugged in See Error Indicators While Cleaning chart for instructions Contact Customer Support All lights flashing on NSI and buttons and robot beeping while charging Incompatible adapter used Remove the incompatible adapter and use only the adapter included with Braava 24 Braava 300 Series Owner s Manual Meijer com Meijer com iRobot NorthStar Navigation Cube Troubleshooting Problem Likely Cause What To Do Braava is not connecting to the Cube Cube won t turn on Cube and robot position C Batteries are dead or inserted incorrectly Turn on the Cube and place it on a raised surface Point the blue light toward an open area of the room Place Braava on the floor 6 to 8 feet away from the Cube facing toward the Cube Turn Braava on With a dry cloth on Braava press the Sweep button Braava should drive toward the Cube and connect with the Cube within 30 seconds If the blue Navigation Indicator lights turn solid blue on Braava it has connected to the Cube It is ok if the Cube continues flashing If Braava is not able to drive straight see Not Driving Properly in the General Troubleshooting chart Replace with new C batteries and confirm batteries are facing the correct direction Cube light is red C Batteries are dead Replace with new C batteries Cube turns off while Braava is cleaning Multiple Cubes are set
3. facing toward the Cube 1 Turn Braava on using the power button The button will light up blue when the cleaner is on 2 To start cleaning with a DRY CLOTH just press the Sweep button 3 To start cleaning with a WET CLOTH just press the Mop button o9 o oo O E 26 O One blue light will start blinking on the Navigation System Indicator if Braava detects a signal from the Cube The light will turn solid blue once it locks onto the Cube f no lights appear Braava does not detect a NorthStar signal e When Braava finishes cleaning it plays a short song returns to where it started and parks itself Braava will also do this if the battery runs low while cleaning e To turn Braava off press the power button for two seconds A tune will play and the light will turn off e Toturn off the NorthStar Navigation Cube press the button on the back corner The light on the opposite corner will turn off global irobot com 21 Meijer com iRobot Maintenance To keep your Braava in the best working condition follow these maintenance steps Cleaning and Storing e Use a dry cloth to wipe dust or dirt from Braava s exterior Do not rinse or submerge in water e Use a damp cloth to wipe off dust and dirt on tires Make sure that Braava is not plugged in and that the cloth is not dripping e Place Braava on its end handle side down when charging or storing between uses e For long term storage remove C batteries
4. Check wheel area for debris and remove or clean as needed e Examine tire treads to make sure they are securely attached to the wheel If not well attached contact Customer Support Braava is backing up Braava drives off and does not clean where started it Floor transition sensor is activated Braava is in Pause Resume mode Remove and reapply cleaning cloth When reapplying follow these instructions e Ensure cloth does not overlap into the middle channel of the removable cleaning pad e Ensure cloth is not bunching up which can prevent the removable pad from reattaching completely to the robot If flooring is uneven or has wide grout lines place Braava on smoother flooring to see if problem persists Braava may still be in pause resume mode from a previous cleaning run Tap the power button to exit pause resume mode When resuming after pausing Braava cleans the same area Braava won t hold a charge 26 Robot position when resuming Incorrect adapter or battery It is normal for Braava to re clean an area while trying to find its position e To help Braava find its position quickly restart Braava near the Cube in the same orientation and location as the beginning of the cleaning cycle e f Braava does not successfully find its position it will start a new cleaning cycle Confirm the adapter has the same model number as noted on the bottom of your Braava and use only an official Braav
5. Cleaning Cloths Disposable Cloths For use only with the Multi Purpose Cleaning Pad e Braava is compatible with most disposable dry and pre moistened cleaning cloths such as Swiffer brand and store brands like Target e Always follow the use and care instructions included with any dry or wet cleaning cloths to care for your floors e Please note that Braava is not compatible with Swiffer WetJet Refills Microfiber Cloths Braava s specially designed microfiber cloths can be rewashed and reused e White cloths are for dry sweeping with the Multi Purpose Cleaning Pad e Blue textured cloths are for mopping and can be used with either the Pro Clean Reservoir Pad or the Multi Purpose Cleaning Pad Dampen cloth before use A NOTICE Wet cloths may not be suitable for cleaning unsealed floors Ask your flooring manufacturer or installer if you are unsure whether damp mopping is safe for your floor Floor Types e Braava is designed to clean hard surface floors including wood tile vinyl linoleum and laminate e Braava cleans best on smooth hard surfaces and may not perform on uneven tiles heavily waxed floors or rough surfaces like slate or brick which can snag the cleaning cloth A NOTICE Braava is not intended to pick up large debris Before cleaning with Braava pick up large debris and check for gravel or sharp objects that could scratch the floor if captured under the cleaning pad global irobot com 13 Meije
6. adapter with a damaged cord or plug e Do not handle or charge Braava when hands are wet e Always disconnect Braava from the adapter before cleaning Notice Braava contains a software interface for the purpose of enabling the manufacturer to provide updates to the internal firmware if any such updates are made available to users Any attempt to access retrieve copy modify distribute or otherwise use any of the Braava software is strictly prohibited FCC Notice This device complies with Part 15 of the FCC rules Operation is subject to the following conditions 1 The device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation A WARNING Changes or modifications not expressly approved by iRobot could void your warranty This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept interference received including interference that may cause undesired operation global irobot com 5 Meijer com iRobot Braava Overview Braava oQ Control Buttons 0O NorthStar Navigation Sensor 0 Navigation System Indicator 0 Bumper 6O Handle o Cube on off button on back corner Removable Cleaning Pad NorthStar Navigation Cube 6 Battery C
7. guides Braava s cleaning Connecting to the NorthStar Navigation Cube e Once Braava starts cleaning it tries to establish a connection to the NorthStar Navigation Cube indicated by one flashing blue light on the Navigation System Indicator Once Braava has locked onto the Cube Braava s lights turn solid blue e The Navigation System Indicator also indicates Braava s range As Braava gets to the edge of its range such as going out of the room or far from the NorthStar Navigation Cube the number of lights will go down e Braava may occasionally drive back toward the NorthStar Navigation Cube to confirm its position before continuing on its cleaning path e Braava builds a new map each time it starts a new cleaning cycle but retains its map if paused during the cleaning cycle Cleaning without a NorthStar Navigation Cube e Because the Cube is just one part of the Navigation System Braava can still clean without a NorthStar signal present however the cleaning area will be much smaller and Braava will not be able to perform edge cleaning in each section Cleaning with multiple NorthStar Navigation Cubes For Braava 380t ONLY e Braava can use multiple NorthStar Cubes to clean up to 2 000 square feet when dry sweeping Braava will move from one Cube to the next extending the cleaning area with each Cube it encounters e Multiple cubes can be used in Mop mode too but Braava limits its wet cleaning area to 350 square feet to
8. Meijer com irtobot Braava Floor Mopping Robot 300 Series Owner s Manual global irobot com Meijer com iRobot Welcome irobot Dear iRobot Braava Owner Welcome to the world of iRobot As an owner of the iRobot Braava Floor Mopping Robot you join a growing group of people around the globe who like you are discovering an easier way to mop their floors The use of practical robots that help you in and around your home is a new reality We encourage you to share your feedback as we continue to develop new and groundbreaking robots Here s what you can do to participate in our efforts e Communicate with us if you have questions comments or require support Contact us at global irobot com Thank you for joining the robot revolution We look forward to your valued input as we continue to deliver groundbreaking products that will change and improve your world On behalf of the entire iRobot team C2 C2 Colin Angle Co Founder and CEO iRobot Corporation 2 Braava 300 Series Owner s Manual iRobot Table of Contents Safety IS ICONS seccsoresetecetencegsnedccneeuescessseyeesscasoeeesssiees 4 sc Rl sssusa mussa Koossa kats eenen 6 SULON SANA B Nro Lon 8 Battery and Charging ti T 10 Sweep and Mop Modes nana kanaa ennen 12 How Braava GIO MS tener inenen nnn derden 14 NorthStar Navigation sean 16 Operating Braav a nennen 18 VAONA GS RR REED 22 Trouble Shooting serenade nde 24 Customer SUD PO t ensen e
9. TION Do not charge Braava while the Pro Clean reservoir pad or any wet cloth is attached Charge using a standard 120V outlet only Only use the included adapter to charge Braava Always disconnect Braava from the adapter before cleaning 10 Braava 300 Series Owner s Manual Meijer com iRobot Turbo Charge Cradle Compatible only with Braava 380 e Plug the adapter into a standard electrical outlet and plug the other end of the cord into the power jack on the Cradle One blue light will appear on the front of the Cradle Place Braava on the Cradle to charge Charge Braava for approximately 2 hours or until a solid blue light appears on Braava s power button Remove Braava from the Cradle before applying cleaning cloths or the Pro Clean Reservoir Pad Charging time and run time can be affected by operating temperature floor type and other conditions Power Jack O Charging Contacts LED indicator TIP Braava s adapter is compatible with the Cradle and can be plugged into either Braava directly or into the Turbo Charge Cradle AS A CAUTION Do not charge Braava while the Pro Clean reservoir pad or any wet cloth is attached Charge using a standard outlet only Only use the adapter included with the Braava 380t See Braava manual for safety warnings and instructions Compatible only with the Braava 380t Charging Indicators The NorthStar While Plugged In Navigation Cube The Cube uses 2 C batter
10. a battery If problem persists contact Customer Support Battery needs refresh charge Charge Braava for 12 hours using the adapter and not a Cradle then run Braava until battery fully depletes Repeat 3 times to achieve expected run times Braava 300 Series Owner s Manual Meijer com iRobot Get Robot Updates Register your Robot Go to global irobot com iRobot Customer Care USA amp Canada If you have questions or comments about this product please contact iRobot before contacting a retailer Please visit the iRobot home support site at www irobot com support for support tips frequently asked questions or information about accessories and other iRobot products Should you still need assistance Call our Customer Care team at 877 855 8593 iRobot Customer Care Hours e Monday Friday 9AM 7PM Eastern Time e Saturday 9AM 6PM Eastern Time iRobot Customer Care Outside USA amp Canada Visit global irobot com to e Learn hints and tips to improve the performance of your robot e Get answers to questions e Download a detailed product manual e Contact your local distributor global irobot com 27 Meijer com 2008 2013 iRobot Corporation 8 Crosby Drive Bedford MA 01730 USA All rights reserved re iRobot and NorthStar are registered trademarks of iRobot Corporation Braava is a trademark of iRobot Corporation Swiffer and WetJet are registered trademarks of Procter and Gamb
11. connection Blue solid light 1 to 3 Locked onto NorthStar Cube The number of lights indicates the strength of Braava s connection to the navigation system with 3 being strongest If there are no lights Braava does not detect a NorthStar signal Other States Blue lights flashing in sequence Thinking Blue lights flashing with pause Sleep mode Red light in middle Error See trouble shooting section for more information O 6 NorthStar Navigation Cube Lights Blue blinking light Power on broadcasting signal Blue solid light Power on connected to Braava Red solid light Batteries low global irobot com 9 Meijer com iRobot Battery and Charging Mode Braava 320 Braava 380t Run Time Sweep up to 3 hrs up to 4 hrs Mop 2 hrs 2 5 hrs Charge Time N A 10 hrs 2 hrs Charging Stand Braava on its end to access the charging port Plug the adapter into a standard electrical outlet and into Braava s charging port Charge Braava until a solid blue light appears on the power button It may take Braava a few charging cycles to reach its full capacity The blue light indicates on average that the battery has charged to 80 of its capacity Charging time and run time can be affected by operating temperature floor type and other conditions Charging Port TIP Braava 380t can also be charged with the Braava Turbo Charge Cradle See Cradle instructions for details pg 11 A CAU
12. ear any objects that are burning or smoking e Before using Braava remove fragile objects from the cleaning area including objects on furniture that can fall if the furniture is pushed or bumped e Move any power cords as well as cords for blinds and curtains out of the way to reduce the risk of objects being pulled down e Block off access to open balconies near the cleaning area with physical barriers 4 Braava 300 Series Owner s Manual Meijer com Meijer com iRobot e Make sure the cleaning cloth does not drape into the middle channel between the gripping strips as this could impede sensor functions and safe operation See page 18 for further detail e When mopping do not use Braava in areas where wetness can damage unfinished or unsealed floors or delicate carpeting or rugs e Operate at room temperature Do not expose Braava or its batteries to freezing or extreme heat e his appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety BATTERY AND CHARGING e Charge using a standard U S 120V AC outlet only e Only use the included adapter to charge Braava Braava 320 and 380t chargers are not cross compatible e Only use rechargeable battery packs approved by the manufacturer e Do not use an
13. ep followed by the start cleaning song Braava typically cleans the same total area as the standard detailed cleaning mode but will skip detailed cleaning around furniture and some walls to save time Pause Resume Braava will automatically pause if you pick it up or press any button while cleaning The cleaning mode button will flash blue to indicate the cleaning cycle is paused While paused Braava will save the map of the area it has already cleaned To resume cleaning place Braava within 6 feet of the Cube where it originally started facing in the same general direction it started Press the flashing cleaning mode button Braava will start cleaning while it determines its position on the map Once it confirms its position it will drive to an area not yet covered and continue cleaning Braava may re clean an area already covered or explore new areas of cleaning while determining its position on the map If you resume Braava where you paused it it may take longer for the cleaner to determine its position depending on its distance from the Cube To exit Pause and quit the cleaning cycle power Braava off by holding the power button for 2 seconds Note Braava can only be paused after it has locked onto the NorthStar Navigation Cube at the beginning of the cleaning cycle global irobot com 15 Meijer com iRobot NorthStar Navigation The NorthStar Navigation Cube acts as a beacon emitting a signal that
14. fluid on your floor do not leave Braava unattended when mopping and remove from floor once Braava stops cleaning When mopping is finished e Empty any remaining fluid from the reservoir e Leave the fill cap open to allow reservoir to dry completely Do not store the pad on Braava if wet e See page 22 for care instructions global irobot com 19 Meijer com iRobot Place the NorthStar Cube 1 Press the button on the back corner of the NorthStar Navigation Cube to turn it on A blue light will flash on the opposite corner when turned on and then go solid when Braava locks onto it If you forget to turn the Cube on Braava will send a signal to try to turn it on f Braava is successful the blue flashing light will appear on the Cube 2 Place the NorthStar Navigation Cube on a table or counter top pointing the blue light away from walls and toward the middle of the room For Best Results e Place the NorthStar Navigation Cube where it has a clear view of the ceiling for example no cabinet or shelf directly above it e Do not move the NorthStar Navigation Cube once Braava has started cleaning as it may impair Braava s cleaning performance e Do not put the NorthStar Navigation Cube on the floor as the cleaner may run into it and move it 20 Braava 300 Series Owner s Manual Meijer com iRobot Start Cleaning Place Braava on the floor within 6 8 feet of the NorthStar Navigation Cube
15. from the NorthStar Cube Wheel Guard e As Braava cleans debris may accumulate around the Wheel Guards This helps keep Braava s wheels moving freely e Periodically check Braava s wheels to see if debris has accumulated and remove as needed e A small notch next to the wheel allows access with tweezers or scissors if needed to free the debris Access Notch 22 Braava 300 Series Owner s Manual Meijer com iRobot Pro Clean Reservoir Pad Sold separately for Braava 320 e Hand rinse with water in the sink to clean Do not put the reservoir pad in the dishwasher Do not wash with soap e Let dry completely before re attaching to Braava after cleaning is complete e he wick is designed for repeated use and includes antimicrobial material Do not remove the wick cap between cleanings e f the wick cap becomes dirty or shows wear it can be replaced e Remove the wick cap by pulling on the side rubber tab e Replace with a new wick cap pressing firmly into place to create a tight seal to prevent leaking global irobot com 23 iRobot Trouble Shooting Visit global irobot com for additional tips and trouble shooting a Navigation System Indicators NSI Error Indicators on the Navigation System Indicator NSI while cleaning Problem Likely Cause What To Do Solid red light on the middle NSI Red light blinks 2 to 6 times on the middle NSI System error Braava is stuck in its enviro
16. h 1 Set Braava on its end and remove the cleaning pad 2 Attach a dry or wet cloth to the Multi Purpose cleaning pad Lay the removable pad on an open cleaning cloth Attach cloth by tucking it into the gripping strips on both sides See the following page for the Pro Clean Reservoir Pad 3 Re attach the cleaning pad Magnets will help it snap back into place eN CAUTION Make sure the cleaning cloth does not drape into the middle channel between the gripping strips as this could impede sensor functions and safe operation 18 Braava 300 Series Owner s Manual Meijer com iRobot Using the Pro Clean Reservoir Pad Sold separately for Braava 320 The Pro Clean Reservoir Pad dispenses liquid as Braava mops to keep the cleaning cloth wet longer Fill the reservoir 1 Open the fill cap by pulling and swiveling it to the side 2 Fil reservoir with water and replace fill cap pressing it in securely so it does not leak 3 Fill the reservoir over a sink as a small amount of fluid can leak out when the fill cap is closed 4 Dampen the blue Pro Clean microfiber cloth and press onto the velcro strips Do not use a dry cloth TIP Fluid dispenses at different rates depending on floor type and solution used The first time you mop start with the cloth only slightly damp and then increase the starting cloth wetness if needed A NOTICE To avoid the Pro Clean Reservoir Pad leaving excess
17. harging Port 0 Floor Transition Sensors Wheel Guards O Charging Adapter D 4p Turbo Charge Cradle 380t 6 Braava 300 Series Owner s Manual iRobot Multi Purpose Cleaning Pad For dry sweeping or wet mopping disposable or reusable microfiber cloths _ Cloth Gripping Strips A Middle Channel for Floor Transition Sensors Pro Clean Reservoir Pad Ships with Select Models For wet mopping with the blue Pro Clean microfiber cleaning cloth Fill Cap B Reservoir Wick global irobot com Meijer com Meijer com iRobot Buttons and Lights Power Button Press once to turn Braava on Hold for 2 seconds to turn Braava off Blue solid light Power on Red blinking light Battery starting to get low Red solid light Low battery needs to be recharged Sweep Button For use with dry cloths Press once to start cleaning Press while cleaning to pause Blue solid light Sweep mode activated Blue blinking light Sweep mode paused Q Mop Button For use with wet cloths Press once to start cleaning Press while cleaning to pause Blue solid light Mop mode activated Blue blinking light Mop mode paused Holding the cleaning mode button will activate Quick Clean Mode See page 15 8 Braava 300 Series Owner s Manual Meijer com iRobot O Navigation System Indicators NorthStar Connection Blue blinking light 1 Establishing
18. ies The battery door can be found on the bottom of the Cube O Power Button Red pulsing light Battery charging Blue solid light Battery charged eS Please dispose of all batteries properly by finding a recycling resource near you global irobot com 11 Meijer com iRobot Sweep and Mop Modes Braava sweeps and mops hard surface floors using readily available dry and wet cleaning cloths or the included reusable microfiber cloths Braava is not a vacuum and is not intended for use on carpets Sweep Mode Sweep mode is intended for cleaning with a dry cloth In Sweep mode Braava moves ahead in a straight line when it begins cleaning then cleans back and forth 9 in parallel lines It is ideal for picking up dust dirt and hair to maintain clean grit free floors every day Mop Mode Mop mode is intended for cleaning with a wet cloth In Mop mode Braava drives forward a short distance to one side backs up slightly then moves forward to the other side alternating to the left and right as it progresses This mopping action helps dissolve and pick up the deeper dirt and grime on your floors Braava automatically adjusts to a smaller cleaning area in Mop mode to optimize cleaning while the cloth is wet TIP Start with dry Sweep mode to pick up surface grit and then follow with a wet cloth in mopping mode to get a deeper clean 12 Braava 300 Series Owner s Manual Meijer com iRobot
19. le Target is a registered trademark of Target Brands Inc U S Pat http www irobot com patent Other Patents Pending WC 4407714 Braava300Series Manual EN
20. nment and cannot free itself e Press and hold the power button to turn Braava off e Vigorously rotate both wheels for 15 seconds e Place Braava on floor and power it on Make sure a dry cleaning cloth has been applied e f red light is gone press Sweep e f red light persists contact Customer Support Remove Braava from the situation and restart in a new area Red light blinks 14 times on the middle NSI Red light blinks 15 times on the middle NSI Braava has detected the motor is getting too hot Braava is stuck in too small of an area and cannot free itself Turn Braava off and let it cool down before resuming cleaning Remove Braava from the situation and restart in a new area Red light on the middle NSI when pressing Sweep or Mop accompanied by 3 beeps A sensor is activated so Braava won t start driving Remove and reapply cleaning cloth When reapplying follow these instructions e Ensure cloth does not overlap into the middle channel of the removable cleaning pad e Ensure cloth is not bunching up which can prevent the removable pad from reattaching completely to the robot Error Indicators on the Navigation System Indicator NSI while charging Problem Likely Cause What To Do Solid red light on the middle NSI Red light blinks 7 or 8 times on the middle NSI System error Charging error This is not a charging error but will prevent Braava from
21. optimize for cloth wetness Braava 320 Braava 380t 800 sq ft 1 000 sg ft 250 sg ft 350 sq ft up to 2 000 sq ft with additional NorthStar Cube sold separately 16 Braava 300 Series Owner s Manual Meijer com iRobot Setting Up NorthStar Navigation Cubes Using Braava with one Cube e Place the Cube near the center of the area you want to clean and start Braava nearby e Braava will clean the area around the Cube and may extend into other rooms based on the cleaning mode and how far the NorthStar signal reaches e f you have a choice of rooms place the Cube in a larger room to maximize NorthStar coverage e Once Braava has completed its run you can move the Cube to clean a different part of your home Using Braava with multiple Cubes For Braava 380t ONLY e Use one or more extra Cubes sold separately to expand how far Braava cleans in a single run e Place extra Cubes in rooms or areas next to the area covered by the first Cube The Cubes should typically be between 20 and 25 feet from each other for the NorthStar coverage to overlap e Braava will automatically clean from one Cube to another Cubes are pre programmed to different NorthStar channels indicated on the bottom of the Cube Cubes with different channels must be used for multi Cube cleaning One Cube Multiple Cubes global irobot com 17 Meijer com iRobot Operating Braava Put On a Cleaning Clot
22. r com iRobot How Braava Cleans Braava intelligently cleans your floor by mapping the room as it cleans Cleaning Cycle e Braava cleans your home in sections first cleaning areas to its right and later returning to areas to its left e When the open areas in each section are complete Braava cleans along edges of furniture and walls before moving on e When finished Braava returns to where it started and parks itself Cleaning Pattern e n open areas Braava methodically cleans back and forth across your floor e As Braava encounters chair legs furniture and other obstacles it cleans around them and continues its cleaning pattern e Braava detects stairs and will maneuver away from drop offs and back to the cleaning area As a safety precaution open ledges or balconies with a drop of 2 feet or more should be blocked off with a physical barrier e Braava also detects area rugs and raised transitions to carpet so it can avoid driving on to them Note If your carpet is flush with your hard surface floor you may need to add a temporary barrier to provide Braava a boundary it can detect e Braava follows along walls and edges as it encounters them and asit completes each section it cleans 14 Braava 300 Series Owner s Manual Meijer com iRobot Quick Clean Mode Cleans 30 faster by focusing cleaning on open areas Activate by holding the Sweep or Mop button for 3 seconds You will hear a single be
23. tende 27 global irobot com 3 Meijer com iRobot IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY A CAUTION Do not expose the electronics of Braava its battery or the adapter There are no user serviceable parts inside Refer servicing to qualified service personnel WARNING READ AND SAVE THESE INSTRUCTIONS To avoid the risk of injury or damage these basic precautions should always be followed e Read all safety and operating instructions before using Braava e Read and heed all warnings in this manual and on Braava the Cube and the adapter e Only use Braava in accordance with the specifications outlined in this manual e Do not attempt to repair or adjust any electrical or mechanical functions on this device Tampering with these functions may create a hazardous condition and it will void your warranty e Be aware that floors may be slippery after wet cleaning with Braava e Braava operates very quietly Take care when walking in the area Braava is cleaning to avoid stepping on Braava and tripping USE RESTRICTIONS e Braava is not a toy Supervise children and pets when Braava is cleaning e Braava has electrical parts Do not spray rinse or submerge it in water Clean with a dry cloth only e Braava is for indoor use on hard surface floors only e Do not use Braava to pick up large debris liquid spills bleach paint or other chemicals e Do not use Braava n
24. up but Braava is only using one Cube Signal interference Make sure Cube is not placed within 5 feet of a Plasma or LCD television and that the Cube is not in a room with fluorescent lighting turned on Braava is out of range Cube position When Braava travels out of range it is normal for the Cube to turn off When Braava returns it will send a message to the Cube to turn it back on Braava must be able to encounter a second Cube while cleaning to use it Make sure the second Cube is not isolated in an area where Braava cannot get to it Try placing Cubes with just 15 feet between them to help Braava connect then move the Cubes farther apart for subsequent cleaning cycles Do not move the Cubes while Braava is cleaning Multiples Cubes are set up but Braava is over cleaning many areas Cube channels Confirm the Cubes in use all have different channels The channel number can be found on the bottom of each Cube Pro Clean Reservoir Pad Troubleshooting Problem Leaking or leaving puddles Not wicking fluid Likely Cause Loose wick or fill cap Wick cap requires replacement What To Do Check the fill cap and the wick cap and make sure both are securely sealed shut Fluid will dispense at a faster rate if these caps are not sealed Refer to Reservoir Pad maintenance for instructions to replace the wick cap global irobot com 25 iRobot General Troubleshooting Problem

Download Pdf Manuals

image

Related Search

Related Contents

CableWholesale 50ft, S-Video - S-Video  Istruzioni per l`uso  Stoves Richmond 900DF  Sony XR-3501MK2 User's Manual  MANUAL DEL PROPIETARIO Honda CRF50F  Gebrauchsanleitung Instructions for use    SmartMetals 063.7240  Soehnle Style  VarioGuide™: ein neues rahmenloses bildgesteuertes  

Copyright © All rights reserved.
Failed to retrieve file