DELL Latitude E6410 notebook
Contents
1. Replacing the System Board To replace the system board perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts WLAN Card Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the WLAN Card K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the access panel Disconnect the antenna cables from the WLAN card E a AE 6 Remove the screw that secures the WLAN card to the computer 7 Remove the WLAN card from the computer Replacing the WLAN Card To replace the WLAN card perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts WWAN Card Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compl2. Default setting Disabled Allows you to enable or disable the ability of USB devices to wake the computer from Standby This feature is only functional when the AC power adapter is connected If the AC power adapter is removed during Standby the BIOS will remove power from all of the USB ports to conserve battery power Default setting Disabled Allows the computer to turn on by a special LAN signal or from Hibernate state when triggered by a special wireless LAN signal Wake up from the Standby state is unaffected by this setting and must be enabled in the operating system Disabled Do not allow the system to power on when it receives a wake up signal from the LAN or wireless LAN LAN Only Allow the system to be powered on by special LAN signals WLAN Only Allow the system to be powered on by special WLAN signals LAN or WLAN Allow the system to be powered on by special LAN or wireless LAN signals Default setting Disabled Allows you to enable or disable the ExpressCharge feature NOTE ExpressCharge may not be available for all batteries Allows you to enable or disable the battery charger If disabled the battery will not lose power when the system is connected to an AC adapter but it will not charge either Default setting ExpressCharge Allows you to enable or disable the BIOS warning messages when you use certain power adapters The BIOS displays these messages if you attempt to use a power adapter that has t
3. E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Battery SF K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below 1 Follow the procedures in Before Working Inside Your Computer 2 Slide the battery latches toward the center of the computer 3 Slide the battery out of the computer and remove it Replacing the Battery To replace the battery perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Bluetooth Card Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Bluetooth Card E NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the SIM card Remove the SD card Remove the ExpressCard Remove the
4. Remove the access panel Remove the coin cell battery Remove the Heat Sink and Processor fan 10 Remove the LED cover 11 Remove the keyboard 12 Remove the display assembly 13 Remove the palm rest 14 Remove the modem 15 Remove the modem connector 16 Remove the ExpressCard cage 17 Remove the palm rest 18 Remove the system board 19 Remove the screw that secures the I O port card to the computer 909 NO ye a a 20 Lift the left edge of the I O port card and remove the I O port card from the computer Replacing the I O port card To replace the I O port card perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Keyboard Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Keyboard K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG port cover applicable on E6410 ATG computer only Remove the battery Remove the LED cover Remove the screws that secure the keyboard to the computer E a AE 6 Use a plastic tab to lift the back edge of the
5. Remove the hard drive Remove the hinge covers Remove the access panel 10 Remove the Latitude ON Flash CMG module 11 Remove the WWAN card 12 Remove the WLAN card 13 Remove the coin cell battery 14 Remove the LED cover 15 Remove the keyboard 16 Remove the Fingerprint Reader 17 Remove the Display Assembly 18 Remove the ExpressCard cage 19 Remove the palm rest 20 Remove the system board 21 Unthread the power source cable from the computer 1909 NO U BEUR N E 22 Lift up the power source port to remove from the computer Replacing the Power Connector To replace the power connector perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Processor Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Processor K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the access panel Remove the Heat Sink and Processor fan Rotate processor cam lock counter clock wise e
6. The Activate and Disable options will permanently activate or disable the feature and no further changes will be allowed Default Setting Deactivate Allows you to enable or disable the Execute Disable mode of the processor Default setting Enabled Allows you to determine whether changes to the setup options are allowed when an Administrator Password is set If disabled the setup options are locked by the admin password Allows you to determine the minimum and maximum length of Administrator and System passwords Allows you to prevent users from entering Setup when an Administrator password is set Enables or disables multi core support for the processor Setting options are All 1 and 2 Default Setting All Enables or disables the Intel SpeedStep feature Default Setting Enabled Enables or disables the Intel TurboBoost performance Default Setting Enabled Power Management Option AC Behavior Auto On Time USB Wake Support Wake on LAN WLAN ExpressCharge Charger Behavior POST Behavior Option Adapter Warnings Keypad Embedded Allows you to enable or disable the computer from turning on automatically when an AC adapter is connected Default Setting Wake on AC Disabled Allows you to set the time at which the computer must turn on automatically You can set the of days if any when you would like the system to turn on automatically The settings are Disabled Everyday or Weekdays
7. and aligned K NOTE The color of your computer and certain components may appear differently than shown in this document To avoid damaging your computer perform the following steps before you begin working inside the computer 1 Ensure that your work surface is flat and clean to prevent the computer cover from being scratched 2 Turn off your computer see Turning Off Your Computer 3 Ifthe computer is connected to a docking device docked undock it A CAUTI ON To disconnect a network cable first unplug the cable from your computer and then unplug the cable from the network device oe Disconnect all network cables from the computer Disconnect your computer and all attached devices from their electrical outlets Where applicable disconnect any adapters from the computer Close the display and turn the computer upside down on a flat work surface A CAUTI ON To avoid damaging the system board you must remove the main battery before you service the computer Sees gt D 11 12 Remove the main battery Turn the computer top side up Open the display Press the power button to ground the system board CAUTI ON To guard against electrical shock always unplug your computer from the electrical outlet before opening the display CAUTI ON Before touching anything inside your computer ground yourself by touching an unpainted metal surface such as the metal at the back of the computer While you work periodica
8. 2 keyboard the same way you use the lt Fn gt key on the computer s internal keyboard NOTE USB keyboards cannot emulate the lt Fn gt key if you are running an ACPI operating system such as Microsoft Windows XP USB keyboards will only emulate the lt Fn gt key in non ACPI mode for example when you are running a DOS Default setting Enabled Allows you to enable or disable the Fast Boot feature The following options are available Minimal Boot quickly unless the BIOS has been updated memory changed or the previous POST did not complete Thorough Do not skip any steps in the boot process Auto Allow the operating system to control this setting this works only when the operating system supports Simple Boot Flag Default setting Minimal Used in conjunction with iAMT 4 0 Allows users to initiate contact with a management console while residing outside of the corporate infrastructure i e remote location behind a firewall or NAT etc Use the check box to enable or disable this feature Default setting Disabled Specifies whether a Virtual Machine Monitor VMM can utilize the additional hardware capabilities provided by Intel Virtualization Technology Default setting Enabled Specifies whether a Virtual Machine Monitor VMM can utilize the additional hardware capabilities provided by Intel Virtualization Technology for Direct I O Default setting Disabled Specifies whether a Measured Virtu
9. Latitude E6410 Depth Height Width Weight Latitude E6410 ATG Depth Height Width Weight minimum 238 30 mm 9 38 inches front height 25 40 mm 1 00 inch back height 31 20 mm 1 22 inches 335 00 mm 13 10 inches 1 95 kg 4 30 Ib 245 80 mm 9 67 inches front height 31 20 mm 1 22 inches back height with port cover 39 50 mm 1 55 inches 341 00 mm 13 42 inches 2 68 kg 5 90 Ib Environmental Operating Relative humidity maximum ee Se Operating 10 to 90 noncondensing Non operating 5 to 95 noncondensing Maximum vibration Operating 0 66 Grms 2 Hz 600 Hz Non operating 1 30 Grms 2 Hz 600 Hz NOTE Vibration is measured using a random vibration spectrum that simulates user environment Maximum shock SS Operating 110 G 2 ms Non operating 160 G 2 ms NOTE Shock is measured with hard drive in head parked position and a 2 ms half sine pulse Altitude ee Operating 15 20 m to 3048 m 50 ft to 10 000 ft Non operating 15 20 m to 10 668 m 50 ft to 35 000 ft Back to Contents Page Back to Contents Page Access Panel Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Access Panel K NOTE You may
10. PS2 and ECP Parallel Port Serial Port SATA Operation Miscellaneous Devices Latitude ON Reader Keyboard Illumination Video Option Ambient Light Sensor LCD Brightness Security Option Admin Password System Password Internal HDD Password Password Bypass Password Change Strong Password Default Setting ECP Allows you to configure the integrated serial port The options are Disabled COM1 COM2 COM3 and COM4 Default Setting COM1 Allows you to configure the internal SATA hard drive controller The options are Disabled ATA AHCI and RAID On Default Setting RAID On Allows you to enable or disable the following devices Internal Modem Module Bay ExpressCard or PC Card Media Card PC Card and 1394 External USB Port Microphone eSATA Ports Hard Drive Free Fall Protection Camera and Microphone Default setting All enabled Allows you to configure the operating mode of the Latitude ON Reader The options are Disabled and Enabled Default Setting Enabled Allows you to configure the keyboard illumination feature The options are Disabled Auto ALS and Input and Auto Input Only Default Settings Disabled To enable the Ambient Light Sensor select the Ambient Light Sensor check box Default Settings Disabled Allows you to set the display brightness depending up on the power source On Battery and On AC Allows you to set change or delete the administra
11. and Replacing Parts Heat Sink and Processor Fan Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Heat Sink and Processor Fan K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the access panel Remove the coin cell battery Disconnect the fan cable from the system board O BEUN oa 7 Loosen the captive screws on the heat sink 8 Lift the edge of the heat sink that is closest to the center of the computer and then slide the heat sink out of the computer Replacing the Heat Sink and Processor Fan To replace the heat sink and processor fan perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Hinge Covers Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Remo
12. memory Mobile Intel 5 series chipset QM57 dual channel 64 bits NOTE You must install memory in pairs for the dual channel mode to work SPI 32 Mbits 32 bits 33 MHz Intel Core i5 series Intel Core i7 series Intel Core i5 520M 540M Dual Core 3 MB Intel Core i7 620M Dual Core 4 MB 1066 MHz NOTE Only 64 bit operating systems can detect memory capacities greater than 4 GB Video Type Controller UMA Discrete Output E6410 UMA or Discrete video controller E6410 ATG UMA Intel Graphics Media Accelerator HD NVIDIA Quadro NVS 3100M 15 pin VGA connector 20 pin DisplayPort connector NOTE DisplayPort DVI and VGA is offered through the docking station Audio Type Controller Speaker two channel high definition audio codec HDA IDT 92HD81B Controller two Internal speaker amplifier Volume controls Communications Modem Network adapter Wireless GPS ExpressCard 1 W channel volume up volume down and mute buttons internal modem optional 10 100 1000 Mbps Intel 82577LM Gigabit Ethernet Controller dedicated WLAN WWAN and Bluetooth mobile broadband mini card NOTE The ExpressCard slot does NOT support PC Cards ExpressCard connector Cards supported PC Card ExpressCard slot 54 mm ExpressCard 34 mm ExpressCard NOTE You can order E6410 with either an ExpressCard slot or a PC card slot NOTE E6410 ATG does not suppo
13. removal instructions from step 8 to loosen the 9th screw which is a captive screw 1909 NO U BEUR N E 24 Remove the screws that secure the palm rest to the computer 25 Disconnect the speaker cable 1 power button cable 2 touch pad cable 3 and RFID cable 4 4 NOTE RFID cable is available only if your computer is purchased with contactless smart card solution 26 Lift the back edge of the palm rest and pull on the right side to release the right snaps Once the right snaps release pull the palm rest forward along the front to release the front snaps and remove the palm rest Replacing the Palm Rest To replace the palm rest perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Power Connector Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Power Connector K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the Memory Remove the ExpressCard Remove the optical drive
14. screws that secure the right display bracket to the display panel Replacing the Display Panel To replace the display panel perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts ExpressCard Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the ExpressCard K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Press and release the card eject button ue ae 4 Press the card eject button to release the card 5 Remove the card out of the computer Replacing the ExpressCard To replace the ExpressCard perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Processor Fan Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Remov
15. D cover 13 Remove the keyboard 14 Remove the coin cell battery 15 Remove the memory 16 Remove the WWAN card 17 Remove the WLAN card 18 Remove the Latitude On Flash CMG module 19 Remove the Fingerprint Reader 20 Remove the Heat Sink and Processor Fan 21 Remove the Display Assembly 22 Peel back the Ferrite sheet covering the firewire cable 1909 NO U BEUR N E 23 Disconnect and unthread the firewire data cable from the system board 24 Remove the screws that secure the IEEE 1394 board to the computer 25 Remove the IEEE 1394 board from the computer Replacing the I EEE 1394 Port To replace the IEEE 1394 port perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts I O port card Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the I O port card K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG port cover applicable on E6410 ATG computer only Remove the battery Remove the optical drive Remove the hard drive Remove the hinge covers
16. Dell Latitude E6410 E6410 ATG Service Manual Working on Your Computer Removing and Replacing Parts Diagnostics System Setup Notes Cautions and Warnings K NOTE A NOTE indicates important information that helps you make better use of your computer amp CAUTION A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed WARNING A WARNING indicates a potential for property damage personal injury or death If you purchased a Dell n Series computer any references in this document to Microsoft Windows operating systems are not applicable Information in this document is subject to change without notice 2010 Dell Inc All rights reserved Reproduction of this material in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell the DELL logo Latitude ON and Latitude are trademarks of Dell Inc Intel Pentium Celeron Intel SpeedStep Intel TurboBoost and Core are either trademarks or registered trademarks of Intel Corporation Bluetooth is a registered trademark owned by Bluetooth SIG Inc and is used by Dell under license Microsoft Windows Windows Vista and the Windows Vista start button are either trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries Adobe the Adobe logo and Flash are either registered trademarks or trademarks of Adobe Systems Incorpo
17. LASH ON ON PT System board error FLASH ON FLASH Display panel error OFF FLASH OFF Memory compatibility error Memory is detected but has errors OFF FLASH FLASH a a A _ FLASH FLASH FLASH a a A FLASH FLASH OFF a a amp a a T FLASH FLASH ON Video card error Back to Contents Page Reseat the processor Replace the system board Replace the processor Reseat the display cable Replace the display panel Replace the video card system board Install compatible memory modules If two modules are installed remove one and test Try the other module in the same slot and test Test the other slot with both modules Replace the memory Replace the system board Reseat the memory If two modules are installed remove one and test Try the other module in the same slot and test Test the other slot with both modules Replace the memory Replace the system board Reseat the modem Replace the modem Replace the system board Replace the system board Reseat the device Replace the device Replace the system board Reseat the hard drive and optical drive Test the computer with just the hard drive and just the optical drive Replace the device that is causing the failure Replace the system board Replace the system board Back to Contents Page Removing and Replacing Parts Dell Latitude E6410 E6410 ATG Service Manual Bluetooth Card System Board Modem Co
18. Smart card Remove the hinge covers Remove the access panel 10 Remove the optical drive 11 Remove the hard drive 12 Remove the LED cover 13 Remove the keyboard 14 Remove the coin cell battery 15 Remove the memory 16 Remove the WWAN card 17 Remove the WLAN card 18 Remove the Latitude ON Flash CMG module 19 Remove the Fingerprint Reader 20 Remove the Heat Sink and Processor Fan 21 Remove the screw that secures the Bluetooth card to the computer 1909 NO U BEUR N E 22 Disconnect the Bluetooth cable from the computer 23 Remove the Bluetooth card from the computer Replacing the Bluetooth Card To replace the Bluetooth card perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Camera Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Camera K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the battery Remove the display bezel Loosen the captive screw that secures the camera to the computer ae 5 Remove the camera from the slot on the
19. al Machine Monitor MVMM can utilize the additional hardware capabilities provided by Intel Trusted Execution Technology Virtualization Technology and Virtualization Technology for Direct I O must be enabled to use this feature Default setting Disabled Wireless Wireless Switch Wireless Devices Maintenance Option Service Tag Asset Tag System Logs Option BIOS Events DellDiag Events Thermal Events Power Events Allows you to determine the wireless devices that will be controlled by the wireless switch WWAN WLAN and Bluetooth Allows you to enable or disable the following wireless devices WWAN WLAN and Bluetooth Displays your computer s Service Tag If for some reason the Service Tag was not already set you would be able to use this field to set it If a Service Tag has not been set for this computer the computer will automatically bring up this screen when you enter the BIOS You will be prompted to enter the Service Tag Allows you to create a system Asset Tag The field can only be updated if the Asset Tag is not already set Allows you to view and clear BIOS POST events It includes the date and time of the event as well as the LED code Allows you to view the diagnostic results from Dell Diagnostics and PSA It includes the time and date the diagnostic and version which was run and the resulting code Allows you to view and clear thermal events It includes the date and time as wel
20. ations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Press and release the SIM card s na 5 Slide and remove the SIM card out of the computer Replacing the SIM Card To replace the SIM card perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Smart Card Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Smart Card K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below 1 Follow the procedures in Before Working Inside Your Computer 2 Remove the ATG Port Cover applicable on E6410 ATG computer only 3 Pull and remove the smart card out of the computer Replacing the Smart Card To replace the smart card perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts System Board Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices inf
21. computer 6 Disconnect the data cable to remove the camera from the computer Replacing the Camera To replace the camera perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts ExpressCard Cage Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the ExpressCard Cage K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the Memory Card Remove the ExpressCard Remove the access panel Remove the hinge covers Remove the LED cover Remove the keyboard 10 Remove the hard drive 11 Remove the fingerprint reader 12 Remove the Heat Sink and Processor fan 13 Remove the display assembly 14 Remove the palm rest 15 Remove the screws that secures the ExpressCard cage to the computer eee ee Se 16 Lift the ExpressCard cage and slide the ExpressCard cage out of the computer Replacing the ExpressCard Cage To replace the ExpressCard cage perform the above steps in reverse order Back to R
22. computer read the safety information that shipped with your computer For additional safety best gt Db B gt practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance CAUTION Many repairs may only be done by a certified service technician You should only perform troubleshooting and simple repairs as authorized in your product documentation or as directed by the online or telephone service and support team Damage due to servicing that is not authorized by Dell is not covered by your warranty Read and follow the safety instructions that came with the product CAUTION To avoid electrostatic discharge ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as a connector on the back of the computer CAUTION Handle components and cards with care Do not touch the components or contacts on a card Hold a card by its edges or by its metal mounting bracket Hold a component such as a processor by its edges not by its pins CAUTION When you disconnect a cable pull on its connector or on its pull tab not on the cable itself Some cables have connectors with locking tabs if you are disconnecting this type of cable press in on the locking tabs before you disconnect the cable As you pull connectors apart keep them evenly aligned to avoid bending any connector pins Also before you connect a cable ensure that both connectors are correctly oriented
23. ee eal a 7 Lift the processor and remove it from the computer Replacing the Processor To replace the processor perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts SD Card Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the SD Card K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below 1 Follow the procedures in Before Working Inside Your Computer 2 Press in on the SD card and release the SD card 3 Pull and remove the SD card out of the computer Replacing the SD Card To replace the SD card perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts SD Card Reader Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the SD Card Reader iN NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrati
24. emory Module To replace the memory module perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Modem Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Modem E NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the LED Cover Remove the keyboard Remove the screw that secures the modem to the computer OBEU tall oa 7 Using the Mylar tab lift the modem up slightly and then slide the modem out of its slot 8 Disconnect the modem cable from the modem to remove the modem from the computer Replacing the Modem To replace the modem perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Modem Connector Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulat
25. emoving and Replacing Parts Back to Removing and Replacing Parts Coin cell Battery Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Coin cell Battery K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the access panel Disconnect the coin cell battery cable from the system board E a AE 6 Lift and remove the coin cell battery out of its socket Replacing the Coin cell Battery To replace the coin cell battery perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Display Assembly Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Display Assembly K NOTE You may need to install Adobe Flash Player from Adobe com in order to
26. erform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Palm Rest Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Palm Rest K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the SIM card Remove the SD card Remove the ExpressCard Remove the Smart card Remove the hinge covers Remove the access panel 10 Remove the optical drive 11 Remove the hard drive 12 Remove the LED cover 13 Remove the keyboard 14 Remove the coin cell battery 15 Remove the memory 16 Remove the WWAN card 17 Remove the WLAN card 18 Remove the Latitude ON Flash CMG module 19 Remove the coin cell battery 20 Remove the Fingerprint Reader 21 Remove the Heat Sink and Processor Fan 22 Remove the Display Assembly 23 Remove the 8 screws Number 1 is a captive screw from the bottom of the computer K NOTE If the computer is installed with a standard palm rest see the fingerprint reader
27. f the computer securing the fingerprint reader o SO BUIN 9 Disconnect the fingerprint reader data cable from the system board 10 Peel off the Mylar to release the cable and fingerprint reader from the computer to remove the fingerprint reader Replacing the Fingerprint Reader To replace the fingerprint reader perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Hard Drive Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Hard Drive K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the screws that secure the hard drive to the computer BEUN 5 Slide and remove the hard drive out of the computer 6 Remove the screw that secures the hard drive caddy to the hard drive 7 Pull and remove the hard drive caddy away from the hard drive Replacing the Hard Drive To replace the hard drive perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing
28. formation that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the LED Cover K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below 1 Follow the procedures in Before Working Inside Your Computer 2 Remove the battery 3 Gently pry up one end of the LED cover and remove it Replacing the LED Cover To replace the LED cover perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Memory Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Memory Module K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the access panel Spread apart the securing clips on each end of the memory module connector until the memory module pops up halal a AE 6 Slide and remove the memory module out of the socket Replacing the M
29. iance Removing the WWAN Card K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the access panel Disconnect any antenna cables that may be connected to the WWAN card E a A a 6 Remove the screw that secures the WWAN card in the computer 7 Remove the WWAN card from the computer Replacing the WWAN Card To replace the WWAN card perform the above steps in reverse order Back to Removing and Replacing Parts Back to Contents Page Working on Your Computer Dell Latitude E6410 E6410 ATG Service Manual Before Working Inside Your Computer Recommended Tools Turning Off Your Computer After Working Inside Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety Unless otherwise noted each procedure included in this document assumes that the following conditions exist Ensure that you have performed all the steps specified in this section You have read the safety information that shipped with your computer A component can be replaced or if purchased separately installed by performing the removal procedure in reverse order A WARNING Before working inside your
30. iance Homepage at www dell com regulatory_ compliance Removing the Modem Plug K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG port cover applicable on E6410 ATG computer only Remove the battery Insert a pin it into the modem plug eject hole on the modem port plug to release and remove the snap securing it BEUN a Replacing the Modem Plug To replace the modem plug perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Optical Drive Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Optical Drive K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the screw that secures the optical drive to the computer i a 4 Press and release the optical drive latch 5 Pull the optical drive out of the computer Replacing the Optical Drive To replace the optical drive p
31. ing the Processor Fan K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the access panel Disconnect the processor fan cable from the system board E a AE 6 Remove the screws that secure the processor fan onto the heat sink 7 Remove the processor fan from the computer Replacing the Processor Fan To replace the processor fan perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Fingerprint Reader Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Fingerprint Reader K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the optical drive Remove the access panel Remove the LED cover Remove the keyboard Loosen the single captive screw labeled F on the bottom o
32. keyboard to release the keyboard 7 Slide the keyboard toward the back of the computer and remove the keyboard from the computer Replacing the Keyboard To replace the keyboard perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Latitude ON Flash CMG Module Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Latitude ON Flash CMG Module K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG port cover applicable on E6410 ATG computer only Remove the battery Remove the left hinge cover See Removing Hinge Covers Remove the screw that secures the Latitude ON Flash CMG module a A 6 Remove the Latitude ON Flash CMG module Replacing the Latitude ON Flash CMG Module To replace the Latitude ON Flash CMG Module perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts LED Cover Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety in
33. l as the name of the event Allows you to view and clear power events It includes the date and time of the event as well as the power state and reason Back to Contents Page Back to Contents Page Diagnostics Dell Latitude E6410 E6410 ATG Service Manual Device Status Lights Battery Status Lights Battery Charge and Health Keyboard Status Lights LED Error Codes Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode Turns on when the computer reads or writes data Turns on steadily or blinks to indicate battery charge status Turns on when a card with Bluetooth wireless technology is enabled To turn off only the Bluetooth wireless technology function right click the icon in the system tray and select Disable Bluetooth Radio Ci Turns on when wireless networking is enabled Battery Status Lights If the computer is connected to an electrical outlet the battery light operates as follows Alternately blinking amber light and blue light An unauthenticated or unsupported non Dell AC adapter is attached to your laptop Alternately blinking amber light with steady blue light Temporary battery failure with AC adapter present Constantly blinking amber light Fatal battery failure with AC adapter present Light off Battery in full charge mode with AC adapter present Blue light on Battery in charge mode with AC adapter
34. l computer Do not use batteries designed for other Dell computers 1 Connect any external devices such as a port replicator battery slice or media base and replace any cards such as an ExpressCard 2 Connect any telephone or network cables to your computer PaA CAUTI ON To connect a network cable first plug the cable into the network device and then plug it into the computer 3 Replace the Battery 4 Connect your computer and all attached devices to their electrical outlets 5 Turn on your computer Back to Contents Page
35. lly touch an unpainted metal surface to dissipate static electricity which could harm internal components Remove any installed ExpressCards or Smart Cards from the appropriate slots Remove the hard drive Recommended Tools The procedures in this document may require the following tools Small flat blade screwdriver 0 Phillips screwdriver 1 Phillips screwdriver Small plastic scribe Turning Off Your Computer Pas CAUTI ON To avoid losing data save and close all open files and exit all open programs before you turn off your computer 1 Shut down the operating system In Windows 7 Click Start and click Shut Down In Windows Vista Click Start then click the arrow in the lower right corner of the Start menu as shown below and then click Shut Down G In Windows XP Click Start Turn Off Computer gt Turn Off The computer turns off after the operating system shutdown process is complete 2 Ensure that the computer and all attached devices are turned off If your computer and attached devices did not automatically turn off when you shut down your operating system press and hold the power button for about 4 seconds to turn them off After Working Inside Your Computer After you complete any replacement procedure ensure you connect any external devices cards and cables before turning on your computer CAUTI ON To avoid damage to the computer use only the battery designed for this particular Del
36. need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Loosen the captive screw that secures the access panel to the base of the computer BEWUS 5 Slide the access panel toward the front of the computer 6 Lift and remove the access panel off of the computer Replacing the Access Panel To replace the access panel perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts ATG Port Cover Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the ATG Port Cover K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below 1 Follow the procedures in Before Working Inside Your Computer 2 Pry and remove the ATG port cover away from the base of the computer Replacing the ATG Port Cover To replace the ATG port cover perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Battery Dell Latitude
37. nnector SD Card Reader ExpressCard Cage IEEE 1394 Port Power Connector ATG Port Cover for E6410 ATG computers only Battery SIM Card SD Card ExpressCard Smart Card Optical Drive Hard Drive Access Panel Hinge Covers coin cell battery Memory WWAN Card WLAN Card Latitude ON Card CMG Module Processor Fan Heat Sink and Processor Fan Processor Modem Connector Plug Modem LED Cover Keyboard Display Bezel Display Assembly Display Panel Camera Fingerprint Reader Palm Rest a 2 2 2 I O Connector Back to Contents Page Back to Contents Page Specifications Dell Latitude E6410 E6410 ATG Service Manual System Information Fingerprint Reader Optional Processor Ports and Connectors Memory Drives Video Display Audio Keyboard Communications Touchpad ExpressCard Battery PC Card AC Adapter Secure Digital SD Memory Card Reader Physical Contactless Smart Cards Optional Environmental K NOTE Offerings may vary by region For more information regarding the configuration of your computer click Start Help and Support and select the option to view information about your computer System Information Chipset Data bus width DRAM bus width Flash EPROM PCI bus Processor Types L2 cache External bus frequency Memory Type Speed Connectors Module capacities Minimum memory Maximum
38. not make any changes to the boot order stored in the BIOS Navigation Keystrokes Use the following keystrokes to navigate System Setup screens Action Keystroke s Exit BIOS lt Esc gt or click Exit Apply a setting click Apply Reset defaults click Load Defaults System Setup Menu Options The following tables describe the menu options for the System Setup program General This section lists the primary hardware features of your computer There are no configurable options in this section System Information System Information Memory Information Processor Information Device Information Battery I nformation Specify the order in which the computer attempts to find an operating system Diskette drive Internal HDD IRRT USB Storage Device CD DVD CD RW Drive Onboard NIC Cardbus NIC Boot Sequence Also allows you to choose the Boot list Option The options are Legacy and UEFI Date Time Displays current date and time settings NOTE System Configuration contains options and settings related to integrated system devices Depending on your computer and installed devices the items listed in this section may or may not appear System Configuration Allows you to configure the integrated network controller The options are Disabled Enabled and Enabled w PXE Integrated NIC Default Setting Enabled w PXE Allows you to configure the parallel port on the docking station The options are Disabled AT
39. ons below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the Memory Remove the ExpressCard Remove the optical drive Remove the hard drive Remove the hinge covers Remove the access panel 10 Remove the Latitude ON Flash CMG Module 11 Remove the WWAN card 12 Remove the WLAN card 13 Remove the coin cell battery 14 Remove the LED cover 15 Remove the keyboard 16 Remove the fingerprint reader 17 Remove the display assembly 18 Remove the ExpressCard cage 19 Remove the system board 20 Disconnect the SD card reader cable from the system board 909 NO ye a a 21 Lift the 2 hooks while pulling the smart card reader to the right of the computer 22 Remove the smart card reader from the computer Replacing the SD Card Reader To replace the SD card reader perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts SIM Card Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the SIM Card K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustr
40. oo little capacity for your configuration Default setting Enabled Allows you to select one of two methods to enable the keypad that is embedded in the internal keyboard Fn Key Only The keypad is only enabled when you hold down the lt Fn gt key By Numlock The keypad is enabled when 1 the Num Lock LED is ON and 2 no external keyboard is attached Note that the system might not notice immediately when an external keyboard is detached Mouse Touchpad Numlock LED USB Emulation Fn Key Emulation Fast Boot Intel Fast Call for Help Virtualization Support Option Virtualization VT for Direct 1 O Trusted Execution NOTE When Setup is running this field has no effect Setup works in the Fn Key Only mode Default setting Fn Key Only Allows you to select one of two methods to use pointing devices Serial Mouse Disable the integrated touch pad when an external Serial mouse is present PS 2 Mouse Disable the integrated touch pad when an external PS 2 mouse is present Touchpad PS 2 Leave the integrated touch pad enabled when an external PS 2 mouse is present Default setting Touchpad PS 2 Allows you to enable or disable the Num Lock LED when the computer boots Default setting Enabled Defines how the BIOS handles the USB devices USB emulation is always enabled during POST Default setting Enabled Allows you to use the lt Scroll Lock gt key on an external PS
41. ormation see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the System Board K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG port cover applicable on E6410 ATG computer only Remove the battery Remove the SIM card Remove the SD card Remove the ExpressCard Remove the Smart card Remove the hinge covers Remove the access panel 10 Remove the optical drive 11 Remove the hard drive 12 Remove the LED cover 13 Remove the keyboard 14 Remove the coin cell battery 15 Remove the memory 16 Remove the WWAN card 17 Remove the WLAN card 18 Remove the Latitude ON Flash CMG module 19 Remove the Fingerprint Reader 20 Remove the Heat Sink and Processor Fan 21 Remove the Display Assembly 22 Remove the palm rest 23 Disconnect the power connector from the system board 1909 NO U nae ae E 24 Disconnect the smart card reader and IEEE 1394 cables from system board 25 Remove the screws that secure the system board to the computer 26 Starting in the back right corner and separate the system board from the I O board connector 27 Lift the back edge of the system board until all the connectors on the left side are separated and slide the system board towards the rear and remove from the computer
42. ory Compliance Homepage at www dell com regulatory_ compliance Removing the Modem Connector NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the Memory Remove the ExpressCard Remove the optical drive Remove the hard drive Remove the hinge covers Remove the access panel 10 Remove the Latitude ON Flash CMG Module 11 Remove the WWAN card 12 Remove the WLAN card 13 Remove the coin cell battery 14 Remove the LED cover 15 Remove the keyboard 16 Remove the fingerprint reader 17 Remove the display assembly 18 Remove the ExpressCard cage 19 Remove the palm rest 20 Remove the system board 21 Unthread the modem connector cable from the computer 1909 NO U nae ae E 22 Lift the modem connector out of its slot and remove Replacing the Modem Connector To replace the modem connector perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Modem Plug Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compl
43. present Battery Charge and Health To check the battery charge press and release the status button on the battery charge gauge to illuminate the charge level lights Each light represents approximately 20 percent of the total battery charge For example if four lights are on the battery has 80 percent of its charge remaining If no lights appear the battery has no charge To check battery health using the charge gauge press and hold the status button on the battery charge gauge for at least 3 seconds If no lights appear the battery is in good condition and more than 80 percent of its original charge capacity remains Each light represents incremental degradation If five lights appear less than 60 percent of the charge capacity remains and you should consider replacing the battery Keyboard Status Lights The green lights located above the keyboard indicate the following A Turns on when the numeric keypad is enabled Turns on when the Caps Lock function is enabled A Turns on when the Scroll Lock function is enabled LED Error Codes The following table shows the possible LED codes that may display in a no POST situation Appearance Appearance _ _Beseription __ _New Step ON FLASH FLASH Install supported memory modules If memory is already present reseat the module s one at time in each slot No SODIMMs are installed Try known good memory from another computer or replace the memory Replace the system board
44. rated in the United States and or other countries ATI FirePro is a trademark of Advanced Micro Devices Inc Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Dell Inc disclaims any proprietary interest in trademarks and trade names other than its own June 2010 Rev A00 Back to Contents Page System Setup Dell Latitude E6410 E6410 ATG Service Manual Entering System Setup Boot Menu Navigation Keystrokes System Setup Menu Options Your computer offers the following BIOS and System Setup options Access System Setup by pressing lt F2 gt Bring up a one time boot menu by pressing lt F12 gt Access the Intel AMT settings by pressing lt Ctrl gt lt P gt Entering System Setup Press lt F2 gt to enter System Setup and make changes to user definable settings If you have trouble entering System Setup using this key press lt F2 gt when the keyboard lights first flash Boot Menu Press lt F12 gt when the Dell logo appears to initiate a one time boot menu with a list of the valid boot devices for the computer Diagnostics and Enter Setup options are also included in this menu The devices listed on the boot menu depend on the bootable devices installed in the computer This menu is useful when you are attempting to boot to a particular device or to bring up the diagnostics for the computer Using the boot menu does
45. rt ExpressCards NOTE The PC card slot does NOT support ExpressCards PC card connector Cards supported Secure Digital SD Memory Card Reader Cards supported Contactless Smart Cards Optional Supported Smart Cards and Technologies Fingerprint Reader Optional PC card slot 54 mm PC Cards NOTE You can order E6410 with either a PC card or an ExpressCard slot NOTE E6410 ATG supports PC Cards only SD MMC SDHC SDHS MiniSD MicroSD SDIO 15014443A 106 kbps 212 kbps 424 kbps and 848 kbps 1S014443B 106 kbps 212 kbps 424 kbps and 848 kbps 15015693 HID iClass FIPS201 NXP Desfire swipe fingerprint sensor Ports and Connectors Audio Video Network adapter Modem IEEE 1394 USB Memory card reader Smart card reader Mini Card one eSATA USB 2 0 compliant connector one 6 in 1 memory card reader integrated smart card reader two half height mini card slots microphone connector stereo headphone speaker connector one 15 pin VGA connector one dual mode DisplayPort connector Docking connector Drives Hard drive Optical drives Display Type and size Active area X Y Dimensions Height Width Operating angle Display Option 1 Maximum resolution Maximum brightness Refresh rate Viewing angle Horizontal Vertical Pixel pitch Display Option 2 Maximum resolution Typical brightness Refresh rate Viewing angle Horizontal Ve
46. rtical Pixel pitch Keyboard Number of keys Layout Backlit keyboard Touchpad Active area X axis Y axis one full height mini card slot one E Family 144 pin docking connector SATA 2 HDD SATA 2 Mobile HDD DVD DVD RW Blu ray Latitude E6410 Latitude E6410 ATG 358 14 mm 14 1 inches diagonal TFT with white LED backlight 303 55 mm x 189 65 mm 11 95 inches x 7 46 inches 358 14 mm 14 1 inches diagonal TFT with white LED backlight 303 55 mm x 189 65 mm 11 95 inches x 7 46 inches 207 mm 8 14 inches 207 mm 8 14 inches 320 mm 12 59 inches 320 mm 12 59 inches O degree closed to 160 0 degree closed to 160 degrees degrees WXGA Anti Glare 1280 H x 800 V at 262K colors WXGA 1280 H x 800 V at 262K colors 40 degrees 40 degrees 15 degrees 30 degrees 0 2373 mm x 0 2373 mm 55 degree 55 degrees 45 degrees 45 degrees 0 2370 mm x 0 2370 mm WXGA Anti Glare 1440 H x 900 V at 262K colors 262K colors 300 nits 630 nits 40 degrees 40 degrees 55 degrees 55 degrees 15 degrees 30 degrees 45 degrees 45 degrees 0 2109 mm x 0 2109 mm 0 2370 mm x 0 2370mm WXGA Touch feature 1280 H x 800 V at United States 83 keys Europe 84 keys Japan 87 keys QWERTY AZERTY Kanji 68 mm 2 67 inches 38 mm 1 49 inches Battery Type Charge time with computer off with 90 W adapter Operating time Life span Dimensions 4 cell
47. smart lithium ion 37 WHr 6 cell smart lithium ion 60 WHr 3 year life time 9 cell smart lithium ion 81 WHr 9 cell smart lithium ion 90 WHr 12 cell smart lithium ion slice 88 WHr 4 6 9 cell approximately 1 hour to 80 capacity and 2 hours to 100 capacity 12 cell approximately 3 hours 20 minutes to 100 Capacity battery operating time varies depending on operating conditions and can significantly reduce under certain power intensive conditions approximately 300 charge discharge cycles Depth 4 cell 6 cell 9 cell 12 cell Height 4 cell 6 cell 9 cell 12 cell Width 4 cell 6 cell 9 cell 12 cell Weight 4 cell 6 cell 9 cell 12 cell Voltage Temperature range Operating Storage Coin cell battery AC Adapter Input voltage Input current maximum Input frequency Output power Output current 65 W E6410 with UMA video only 90 W Dimensions Depth 65 W 90 W Height 65 W 90 W Width 65 W 90 W Temperature range Operating Storage 206 11 mm 8 11 inches 207 77 mm 8 18 inches 14 48 mm 0 57 inch 19 81 mm 0 78 inch 22 10 mm 0 87 inch 217 17 mm 8 55 inches 1 2 CO id 47 00 mm 1 85 inches i E i i 127 00 mm 4 99 inches 147 00 mm 5 78 inches 16 00 mm 0 63 inch 16 00 mm 0 63 inch 66 04 mm 2 60 inches 70 00 mm 2 75 inches 0 C to 35 C 32 F to 95 F 40 C to 65 C 40 F to 149 F Physical
48. the battery Starting from the bottom gently pry the display bezel inside out from the display assembly using a plastic scribe WV 4 When all the snaps loosen remove the display bezel from the display assembly Replacing the Display Bezel To replace the display bezel perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Display Panel Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Display Panel K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the Display Bezel Remove the screws that secure the display panel to the display assembly halal a A 6 Remove the display panel from the top cover and lay it face down on the palm rest 7 Disconnect the touch screen cable 1 and EDP cable 2 from the LCD panel 8 Disconnect the touch screen cable if present 9 Remove the display panel 10 Remove the screws that secure the left display bracket to the display panel 11 Remove the
49. tor admin password When set the admin password enables several security features including Restricts changes to the settings in Setup Restricts the boot devices listed in the lt F12 gt Boot Menu to those enabled in the Boot Sequence field Prohibits changes to the owner and asset tags Substitutes for the system and hard drive password NOTE You must set the admin password before you set the system or hard drive password NOTE Successful password changes take effect immediately NOTE Deleting the admin password automatically deletes the system password as well Default Setting Not Set Allows you to set change or delete the system password When set your computer requests you to enter the system password every time your computer turns on or restarts NOTE Successful password changes take effect immediately Default Setting Not Set This field lets you set change or delete the password on the system s internal hard disk drive HDD Successful changes take place immediately and require a system restart The HDD password travels with the hard drive so the HDD is protected even when installed in another system Default Setting Not Set Allows you to bypass the system and internal hard drive password prompts when your computer restarts or resumes from standby You can set Password Bypass to Disabled and Reboot Bypass NOTE You cannot bypass the system or hard drive password when you turn on your computer that has been sh
50. ut down Default Setting Disabled Allows you to enable the disable permission to the System and Hard Drive passwords when the admin password is set Default Setting Allow Non Admin Password Changes checked Allows you to enable of disable option to enforce strong passwords If enabled all passwords set on the computer must contain at least one uppercase character one lowercase character and be at least 8 characters long Enabling this feature automatically changes the default minimum password length to 8 characters Default Setting Disabled Allows you to enable or disable the Trusted Platform Module TPM on the computer NOTE Disabling this option does not change any settings you may have made to the TPM or delete any information or keys you may have stored there TPM Security Computrace CPU XD Support Non Admin Setup Changes Password Configuration Admin Setup Lockout Performance Option Multi Core Support Intel SpeedStep Intel TurboBoost When TPM is enabled the following options are available Deactivate Disables the TPM The TPM restricts access to the stored owner information and does not execute any commands that use TPM resources Activate Enables and activates the TPM Clear Clears the owner information stored in the TPM Default Setting Disabled Allows you to enable or disable the optional Computrace software The options are Deactivate Disable and Activate NOTE
51. view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG port cover applicable on E6410 ATG computer only Remove the battery Remove the hinge covers Remove the access panel Disconnect and unthread the antennae cable from the WLAN and or WWAN card O BEUN 7 Disconnect and unthread the touch screen cable from the system board Only applies to E6410 ATG computer 8 Loosen the captive screws that secure the display cable to the system board 9 Disconnect and unthread the display data cable from the system board 10 Remove the screws that secure the display assembly to the computer 11 Lift and remove the display assembly from the computer Replacing the Display Assembly To replace the display assembly perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts Display Bezel Dell Latitude E6410 E6410 ATG Service Manual A WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the Display Bezel K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove
52. ving the Hinge Covers K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the screws that secure the hinge covers to the computer aaa na 5 Slide the hinge covers toward the back of the computer and remove the hinge cover Replacing the Hinge Covers To replace the hinge covers perform the above steps in reverse order Back to Removing and Replacing Parts Back to Removing and Replacing Parts I EEE 1394 Port Dell Latitude E6410 E6410 ATG Service Manual WARNING Before working inside your computer read the safety information that shipped with your computer For additional safety best practices information see the Regulatory Compliance Homepage at www dell com regulatory_ compliance Removing the IEEE 1394 Port K NOTE You may need to install Adobe Flash Player from Adobe com in order to view the illustrations below Follow the procedures in Before Working Inside Your Computer Remove the ATG Port Cover applicable on E6410 ATG computer only Remove the battery Remove the SIM card Remove the SD card Remove the ExpressCard Remove the Smart card Remove the hinge covers Remove the access panel 10 Remove the optical drive 11 Remove the hard drive 12 Remove the LE
Download Pdf Manuals
Related Search