Hunter 42" Conroy
Contents
1. the globe with your other hand Carefully remove the globe Unscrew bulbs and replace with bulbs of same type and wattage Reinstall the globe assembly M0028 01 T ERRAL LA allel IN a RT lt a Reverse Switch Changing the direction of air flow move the reverse switch to the opposite position 10 19 12 Hunter Fan Company www HunterFan com 1 888 830 1326 Cleaning the fan use soft brushes or cloths to prevent scratching Cleaning products may damage the finishes For questions regarding removing a light kit call customer service 1 888 830 1326 e Troubleshooting www HunterFan com 1 888 830 1326 Fan doesn t work Excessive wobbling Noisy Operation Make sure power switch is on Tighten all of the blade and Tighten the blade and blade blade iron screws until they iron screws until they are snug Pull the pull chain to make sure are snug it is on e Check to see if any of the e Use the provided balancing blades are cracked If so replace Push the motor reversing switch kit and instructions to balance all of the blades firmly left or right to ensure that the fan it is engaged Check the circuit breaker to ensure the power is turned on Make sure the blades spin freely Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on page 7 Check the plug connection in the swi2. 1 10 19 12 Hunter Fan Company Switch Housing Q Screw two 2 housing assembly screws from the hardware bag halfway into the motor housing It does not matter which two screw holes you choose Feed the wire plug through the center hole of the upper switch housing then wrap keyhole slots around the screws and twist counterclockwise M0028 01 10 19 12 Hunter Fan Company www HunterFan com 1 888 830 1326 R Insert the third screw found in the hardware bag into place and then tighten all three 3 screws Make sure the upper switch housing is securely attached to the mounting plate Failure to properly secure all three assembly screws could result in the switch housing fixture falling e e Light Kit www HunterFan com 1 888 830 1326 Switch Housing Screw Partially install two of the switch housing Align the notches in the sides of the lower Install the third switch housing screw screws found in the bag Connect switch housing with the upper switch Tighten all three screws securely the plugs from the upper and lower housing screws Lift the lower switch housing switch housings Make sure to line up the Twist the lower switch housing clockwise colored markings on the connectors to lock into place Then thread the fan pull chain through the hole in the light kit Want to install your fan without a light kit Make sure the lower switch ho
3. Table of Contents Congratulations on purchasing your new Hunter ceiling fan It will provide comfort and performance in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world To register your fan please visit www HunterFan com register What to Expect with Your Installation M0028 01 10 19 12 Hunter Fan Company Tools Needed Ceiling Bracket www HunterFan com 1 888 830 1326 Preparation YZ SQ Operation amp C Maintenance leaning What to Expect with Your Installation If you are unfamiliar with wiring use a qualified electrician Must be able to secure the fan to building structure or a fan rated outlet box Know your wiring You may need a friend to help you Check box to see fan weight 30 inches from blade tip to nearest wall or obstruction 7 feet from bottom edge of blade to the floor C Assess location 2 M0028 01 10 19 12 Hunter Fan Company t www HunterFan com 1 888 830 1326 Read and Save These Instructions This product conforms to UL Standard 507 A WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an out
4. g off the circuit breakers to the outlet box associated with the wall switch location Make sure all four 4 bumpers are still attached M0028 01 10 19 12 Hunter Fan Company www HunterFan com 1 888 830 1326 Use wood screws Use machine screws included when securing provided with outlet to support structure with box when securing to approved electrical outlet existing ceiling fan rated box Drill 9 64 pilot holes outlet box Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31 8 kg 70 Ibs the hardware bag or less Refer to warning w 1 on pg 2 eye e Ceiling Bracket continued Preparation www HunterFan com 1 888 830 1326 Time Saver Tip Get a helper to insert grommets found in the I hardware bag into the blades while you re doing the next couple of steps 5 M0028 01 10 19 12 Hunter Fan Company Hanging the Fan www HunterFan com 1 888 830 1326 Ground Wire Locking Screw While holding the wires out of the way lift Once the motor is in the ceiling the motor assembly and place the square bracket use the two locking screws hanger into the opening in the ceiling found in the amp hardware bag to secure bracket Be sure
5. let box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Hunter Solid State Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades A CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Hunter replacement parts Tools Needed MI Ladder www HunterFan com 1 888 830 1326 e Power Drill 9 64 Drill Bit Screwdrivers optional optional If mounting to a support structure you will also need these tools 3 M0028 01 10 19 12 Hunter Fan Company Ceiling Bracket To avoid possible electrical shock before installing your fan disconnect the power by turnin
6. nd push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box Hunter Fan Company Motor Housing Raise the motor housing up over the motor and ceiling bracket Turn the motor housing so the screw holes align and the indentation in the housing locks into place with the notch in the ceiling bracket The motor housing is not secured until the next step is complete Do not leave unattended Housing Screw Q With a Phillips head screwdriver install the four motor housing screws found in the hardware bag Tighten all four screws securely M0028 01 10 19 12 Hunter Fan Company www HunterFan com 1 888 830 1326 Blades www HunterFan com 1 888 830 1326 Insert grommets found in the W hardware Lightly attach the blade irons to the bag into the holes in the blades then motor with screws found in secure each blade to a blade iron with the X hardware bag then securely screws found in the A hardware bag tighten after both screws are attached Your blades are shielded with Dust Armor which is ananotechnology coating that repels dust For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning agents may damage the finishes M0028 0
7. tch housing M0028 01 10 19 12 Hunter Fan Company
8. the ground wire attached the motor to the ceiling bracket to the hanger faces out of the large opening in the ceiling bracket Note Fan style may vary M0028 01 10 19 12 Hunter Fan Company r Note To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight 6ulpunoiy For a Single Switch Mo Ja U2215 Using an orange wire Using the orange wire connector from connectors from the hardware bag the hardware bag connect connect the 3 grounding the black wire ungrounded wires green green from the ceiling to the black yellow stripe or bare and the blue wires from the copper coming from the fan Connect the white wire ceiling downrod and SSS grounded from the ceiling to hanging bracket the white wire from the fan Refer to CAUTION c 1 on pg 2 M0028 01 10 19 12 www HunterFan com 1 888 830 1326 papunoi5 For Dual Switches Using orange wire connectors from the amp hardware bag connect the white wire grounded from the ceiling to the white wire from the fan Connect the black wire ungrounded from the ceiling to the black wire from the fan Connect the second ungrounded wire from the ceiling to the blue wire from the fan papunosbun Turn the splices upward a
9. using is securely attached to Go to www HunterFan com FAQs and click the upper switch housing Failure to properly secure all three a z con assembly screws could result in the light fixture falling How do install my fan without the light kit M0028 01 10 19 12 Hunter Fan Company Light Kit continued www HunterFan com 1 888 830 1326 tags Globe A Keeper Finial A Cap 8 Finial Install a light bulb in each socket Press the globe and globe keeper flush against the metal plate Thread the light pull chain through the hole in the center of the finial cap and thread the fan pull chain through the hole in the side of the cap Finally thread only the light pull chain through the hole in the finial and screw the finial onto the threaded rod Connect the appropriate pull chain pendant to each of the short chains coming from the finial and finial cap The fan pull chain controls the speed high See next page for fan medium low and off The light e e e pull chain controls the light operation instructions fixture on and off Note Glass shade style and number of lights may vary M0028 01 10 19 12 Hunter Fan Company Maintenance Operation amp Cleaning Globe Keeper y Finial y Cap Finial Changing the bulbs unscrew the finial and remove it from the threaded rod Remove the finial cap and unscrew the globe keeper while supporting
Download Pdf Manuals
Related Search