REPOTEC RP-1703 cable network tester
Contents
1. for cable test Batter m LAN CABLE TESTER startup menu m LAN CABLE TESTER test menu a ei CTC UNION MODE SEL Icon LCT v1 0 cable test X Press ENTER to test the cable m Results Displayed Type Terminator ID No o 12345678G Pin Out 100BASE HUB i 36145278 UTP FTP or COAX y U T P id 1 Use MODE SEL to toggle between cable pin out screen and result display press ESC back to test menu During any mode of cable testing the first screen display will show the top line out and bottom line in of connections through 8 plus G shield as they are scanned Following this screen page will be the cable identification information If at least one wire pair is not connected the display will read NO CONNECT A shorted cable will read SHORT A question mark in the pin out display indicates a short An unknown is not in the standard known pin outs or in the user defined memory User Defined cable The User Define function allows you to describe your own custom cable pin out which will be entered into the cable identification database and saved in the CPU memory This custom pin out will remain available as long as a fresh battery is in the unit Two methods are available for defining a cable The first method is manual entry while the second uses an UNKNOWN cable as the pin out source First the manual method From the very top of the LAN CABLE TESTER menu just after power on is completed select the USER D2. EF menu by pressing the MODE SEL button step no 1 to 2 The MODE SEL button will now move the cursor to select one of four 4 user memory locations step no 3 Press ENTER to select the memory location that the cursor is on The define cable display will show step no 4 E LAN CABLE TESTER test menu E LAN CABLE TESTER user defined menu MODE SEL MODE SEL cable test MODE SEL user defined X ENTER m LAN CABLE TESTER User Def display 4 locations m LAN CABLE TESTER Define cable display USER DEF x o 12345678G t q mpty 1 Biss MODE SEL to location 1 4 then ENTER Use the ENTER key to set digits 1 to 8 G or blank not connected then press MODE SEL to move to the next space When completed press ESC step no 5 to 6 m LAN CABLE TESTER defined pin out defined m LAN CABLE TESTER Save to User Defined o 12345678G pin out Confirmation display i 34126578 K Esc SAVE TO USER DEF 2 X X To save your definition press ENTER To exit without saving press ESC The alternate method is to save the Unknown type UNKNOWN DEF y SAVE TO USER Keure USER DEF UTP id 1 MODE SEL bef 2 1 2 3 4 ESC out Select the location with MODE SEL and then press ENTER to save Press ESC anytime to exit MODE SEL o 12345678G cable testt X ENTER i 11345678 In the above example Pin 1 and Pin 2 were found to be shorted MODE SEL o 12345678G NO CONNECT cable test X ENTER i In the second example if at least one p
3. LAN Cable Tester With LCT User s Guide Thank you for purchasing this LAN Cable Tester Series product Whether you are a contractor installing LAN cabling as a profession or simply a small office administrator caring for a LAN we hope that you will find this product both useful and rewarding e LCD Display 2 lines by 12 characters with LED back light e Connectors RJ 45 8P8C jacks with shield Palr 3 Pal 3 Palir i Palir 4 AA Palr 4 Polr 2 Palr 1 e Control keys MODE SEL ESC and ENTER buttons 10 100 Base T e Power 9V dry cell battery Token Ring e Size 15 0 H x 6 5 W x 3 5 D cm TP PMD i e Weight 180g net AT amp T 258A T568A USOC EIA TIA 568A B USOC Palr 1 Pal 2 Cable Types 10 100 Base HUB BNC 10Base 2 Unshielded Twisted Pair UTP 100 Cat 3 4 amp 5 plus 4 User Defined Foil screened Twisted Pair FTP 100Q and 120Q Cat 3 4 amp 5 Shielded Twisted Pair STP 150Q IBM Type 1 amp 6 RG 58 Coaxial cable LCT400 ONLY Cable Locator 10BASE T Token Ring TP PMD Cable location may be accomplished by using multiple RP T terminators The RP T locators incorporate factory set I D numbers and are available in ID s from 1 to 16 e Standard pin configurations and four 4 user defined cable wirings Hand held and easy to operate memorized in CPU e Easy to read LCD display with back light e Can save user defined cable directly after testing e Easy to diagnose RJ 45 cables and BNC type
4. air of wires is not connected the test result will show as NO CONNECT CABLE SHORT id 1 41RP 170300 000
5. atically power off To recover from the power off mode the unit must have its power switch cycled OFF and then ON In the power off mode the power usage is close to nil This feature is especially useful if the unit is inadvertently left powered on The battery should be replaced when the battery low icon on the LCD display becomes visible during normal use of the LAN CABLE TESTER Additionally if a low battery is swapped within 1 minute with a new one the user defined memory contents will be retained Just remember to turn the unit OFF before swapping the battery lt Connection The LAN CABLE TESTER is capable of testing cables in any one of four modes Local Test mode is accomplished Terminator Loopback mode uses the by connecting both ends of the supplied terminator ID block connected cable under test to the LAN at the remote end of the cable while the CABLE TESTER OUT and other end of the cable is connected to the r LOOPBACK IN ports Local unit Phe LAN CABLE TESTER OUT s displays an ID equal to zero i Remote Test mode uses two 2 LAN CABLE TESTER units fos with the cable connected between one unit s OUT and the other A units LOOPBACK IN Remote Hira he unit displays an ID equal to zero i Operation continued Turn power switch on Following initial power on of the LAN CABLE TESTER the unit will display the startup logo with back light for 3 seconds then will display the top menu
6. s with LCT400 with preset e Tests for both shielded and unshielded cable types wiring schemes e Review the captured pin assignment and failure status e Easy to read cable status verify cable continuity open short and e Maximum testing length is up to 3000 feet mismatches e Identify and trace the other end s ID with up to 16 individual ID RP T e e e Scan pin assignment Battery low indicator e Automatic cable identification Cable type search Auto power off function The LAN CABLE TESTER has built in power management features intended to extend battery life By far the LCD back light is the most power hungry component in the LAN CABLE TESTER Use of the LCD back light should therefore be limited to low ambient light applications The back light may be toggled ON OFF by simultaneously pressing the MODE SEL and ESC function keys If there is no further menu selection or function testing within thirty 30 seconds the back light will be automatically extinguished Additional power management functions include both a sleep mode and an auto power off mode If there is not any key activity for three 3 minutes the unit will automatically enter sleep mode All interface circuitry and the LCD display will be powered down In this mode the unit draws very little power Pressing any key will cause the unit to wake up to a full functioning state However if there is no key activity for ten 10 minutes the unit will autom
Download Pdf Manuals
Related Search