Premier Mounts LMVP flat panel wall mount
Contents
1. exe uud Oe aaa d dk terasse edit TO T hic DOS Omm 16 VV ili M CPMTP s 17 Weight Limit THE WALL STRUCTURE MUST BE CAPABLE OF m SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF Maximum Flat panel Weight 1 6 O D I THE FLAT PANEL IF NOT THE WALL STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two quali2. 72 Socket Phillips Head Screwdriver Socket Wrench Parts List LMVP Video Wall Mount Assembly Components adl MO Y 5 e One Latch Mounting Base Left and Right Mounting Bracket Qty 1 Qty 1 Each 9 46 Flat Washers Universal Spacers 3 16 Allen Wrench Thread Depth Indicator Universal Washers M8 Nylon Nut M8 Washer Qty 4 Qty 12 Qty 6 Qty 4 Pro Mounting Hardware iti ANNE _I 5146 Concrete Wedge Anchors 546 x 3 Lag Bolts Qty 4 Qty 4 Installation Instructions Visit the Premier Mounts website at http www mounts com Page 3 LMVP gt Parts List contd o un S un D i ey EWM amp 0 DD ED yy M6 x 12mm Screw EW EW D amp yy eo DDD M4 x 12mm Screw ED amp yy em yy yy yy M6 x 16mm Screw em yy amp 55 yy amp yy em M4 x 16mm Screw amp 9 EDD amp 99 2 EDD amp 0 M6 x 25mm Screw em em amp 59 amp 2 em amp 20 M4 x 25mm Screw yy DD EW M8 x 12mm Screw yy yy gy EM M5 x 12mm Screw amp 55 amp yy DOLD amp yy amp yyy M8 x 16mm Screw amp yy amp yy ED yy ED yyy M5 x 16mm Screw em amp 2 amp 959 EDD amp yyy amp 0 M8 x 25mm Screw em em amp 9 e
3. Premier Mounts website at http www mounts com Page 15 LMVP gt N c O O o O Q o 2 D All measurements are in inches millimeters 8 7 6 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PREMIER MOUNTS DIVISION OF lt PMPI gt ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF PREMIER MOUNTS DIVISION OF lt PMPI gt IS PROHIBITED 24 70 23 62 627 4 600 28 7 1 NOTE WHEN REGISTERS ON THE MOUNTING ARMS ARE ALIGNED ACROSS THE ANGLE STARTS WITH A 1 FORWARD TILT TO COMPENSATE FOR WEICHT OF THE UNIT MOUNTS COM 8 7 DIMENSION ARE IN INCH AND MM 3 D PREMIER C4 MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES 1321 South State College Boulevard Fullerton CA 92831 P 800 368 9700 F 800 832 4888 ITEM DESCRIPTION SIZE SCALE DWG NO 1 1 LMVP SHEET 1 OF 1 Installation Instructions Visit the Premier Mounts website at http www mounts com Page 16 b 4 LMVP E PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Pr
4. mount You must secure the mount to two 2 wall studs with four 4 lag bolts 2 lag bolts for each stud found Use a stud finder to determine the exact center of wall studs in the vicinity of the mount Use a pencil to mark the exact center of each of the wall studs Two people are recommended for this step one person to level the mount and another person to mark the wall stud location Place the mount against the wall in the desired viewing location Adjust the mount to align the mount slots in the mount with the center of the wall studs Level the mount Use a pencil to mark the upper right mounting location along the center of the wall stud Drill a pilot hole in the center of the upper right mark using a 74 drill bit and power drill Only use a 74 drill bit when drilling pilot holes Page 6 Visit the Premier Mounts website at http www mounts com Installation Instructions b 4 LMVP ee Installation Step 4 Place the mount against the wall and align it with the pilot hole Insert one 1 h x 3 lag bolt and one 1 washer into the upper right pilot hole Use a socket wrench and a 7 socket to tighten the lag bolt Do not overtighten the lag bolt L evel the mount Use a pencil to mark the remaining four 4 mounting locations along the center of each wall stud Step 6 Two people are recommended for this step one person to lev
5. LMVP Portrait Mode Video Wall Flat Panel Framing System INSTALLATION INSTRUCTIONS gt APREMIER PA MOUNTS THE ORIGINAL MOUNT COMPANY 9541 000 011 0X Rev 1 b 4 E LMVP b STUNG Bag TERR ERR 2 Waming StatemenlS RR PR RRRRRTRMRRW 2 I cuis M 3 aucas 3 OS M 5 lislalling MNE MOUNE NP 6 RO p NER 6 Installing Optional Model Specific Spacers nennen nnns n snis n snis nsns nans 8 Mstaling the Mounting SLACK ONS u L LULU eee au eee ans taie de dT diosa o a te tee td 9 Selecting the Mounting Hardware nnn sa nr aaa sra sna sas s saa rasan nnn 9 Universal Washer IS ATOS de ee USO P IE 10 Universal Spacer Installation a a a a nnne rna anna nns 10 Attaching the Mounting Brackets to the Flat Panel Vs 11 Mounting the Flat Panel MNT 11 Attaching the Flat Panel to the Mount a tac 11 Locking Safety Screw Installation iii 12 Post Installalion AdJuStmeniS nada u L u u L uuu aa heard vH ntc la ni semi en cie ie AUR IF CS 12 Maintenance and Servicing
6. ded inserts found on the back of the flat panel 2 Use a pencil to mark the depth of the threaded Insert on the small straw or toothpick 3 Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 4 Insertthe small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark 5 Locate the correct diameter screw for the threaded insert If the screw you selected is longer than the 1 8 allowance mark on the small straw or toothpick as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark Marking the 1 8 Allowance Marking the Depth 6 Test each size of the screws provided Threaded Insert The correct screws should thread easily into the Small Stan or Toothpick mounting point and not pull out when tension is applied Go to Universal Washer Installation on page 10 N A TN WW Small Straw E K Plus 1 8 Allowance Small Straw Depth Plus 1 8 Allowance or Toothpick Mark or Toothpick Mark Securing the Adapters Optional adapters are available with your LMVP mount Secure the adapters to the LMVP brackets with the supplied M8 washers and nuts Installation Instructions Visit the Premier Mounts website at http www mounts com Page 9 oe LMVP Universal Washer Installation Premier Mounts Universal Washers are de
7. el the mount and another person to drill the pilot holes Drill a pilot hole in the center of each of the marks with a power drill and a 1 4 drill bit A Only use 74 drill bit when drilling the pilot holes 1 Insert one 1 hs x 3 lag bolt and one 1 washer into each pilot hole 2 Tighten all lag bolts using a socket wrench and 72 socket Do not overtighten the lag bolts when attaching the mount to the wall Improper installation may result in personal injury or property damage If you are using OPTIONAL model specific spacers proceed to the Installing Optional Model Specific Spacers on page 8 If not proceed to Installing the Mounting Bracket on page 9 Installation Instructions Visit the Premier Mounts website at http www mounts com Page 7 E LMVP Installing OPTIONAL Model Specific Spacers LMVP s dedicated flat panel spacers are engineered with the knowledge that aligning each flat panel on a large wall is time consuming and costly These model specific spacers are available for most flat panels which significantly reduces the installation time Call Customer Service to inquire about model specific spacers This spacer is shown for illustration purposes only Your spacer may look different depending on the display model you are installing 1 Once your LMVP is mounted in the desired location and is level align your spacer to the top left or right depending on yo
8. emier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries ca
9. fied people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel If mounting to wall studs or ceiling studs make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs Use of an edge to edge stud finder is recommended A It is recommended that a maximum of plaster board be used when mounting to wooden studs Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 mounts mounts com Page 2 Visit the Premier Mounts website at http www mounts com Installation Instructions The following tools may be required depending on your installation or Electronic Stud Finder Pencil Protective Eye Wear Portable Drill 1 4 Drill Bit
10. http www mounts com Installation Instructions LMVP P2 Installing the Mounting Brackets cont d Attaching the Mounting Brackets to the Flat Panel This section presumes that you have read and understood the Selecting the Proper Mounting Hardware section Place your flat panel screen side down on a soft flat surface Identify the number and location of the thread inserts on the back of your flat panel Aligning the holes on each mounting bracket with the thread inserts on the back of your flat panel Secure each mounting bracket to your flat panel by inserting a minimum of two 2 screws per bracket A Do not overtighten the mounting hardware Make sure the directional arrows on the mounting brackets are facing up Proceed to the Mounting the Flat Panel below Mounting the Flat Panel Attaching the Flat Panel to the Mount Mounting bracket adjustments are factory pre set see Note This section requires two people Note These registers must align prior to installation They are factory set Check to determine proper alignment Do not release T flat panel until you are certain that top and bottom hooks of both mounting brackets are securely seated on the upper and lower mounting rails of the wall panel 1 Raise the flat panel past the top and bottom mounting rails on the wall panel 2 Slide the flat panel down slowly keeping it close to the wall 3 Engage the top and botto
11. llation Instructions Tilt Down from tilted up position fi Right Control 4 2 Right Control K TILT Right Control fo TILT Right Control Visit the Premier Mounts website at http www mounts com Level Up LEVEL XS Left Control Level Down from leveled up position d Left Control Rotate Left fen Left Control Rotate Right LEVEL Xe Left Control Page 14 Post Installation Adjustments cont d S Right Control de Right Control S Right Control Right Control Visit the Premier Mounts website at http www mounts com LMVP Installation Instructions LMVP Maintenance and Servicing Installation Instructions Push evenly in the front of the LMVP to release the single latch spring lock Figure 1 Slowly pull the front of the LMVP to extend the scissor arms Figure 2 Loosen the locking safety screws on both mounting brackets Tilt up the bottom of the flat panel then set their kickstands against the bottom tubing of the mount Figures 2 amp 3 You can now reach behind the flat panel for maintenance and servicing or replacement After servicing make sure the spring lock is locked again in the mount s closed position Single Latch Spring Lock Figure 1 Figure 2 Figure 3 Visit the
12. m em amp yyy M5 x 25mm Screw Installation Instructions Visit the Premier Mounts website at http www mounts com Page 4 cL Features The LMVP Portrait Mode Video Wall Flat Panel Framing System is a customizable video wall mounting system featuring multi monitor stacking open design custom spacers and scissor mount extension It has an extending scisso mount for easy installation cable management and servicing Spacers are custom designed for specific flat panels Post Installation Adjustments Patent pending leveling tilt and in out adjustment knobs make it easier than ever to flush and level the flat panels for a seamless video wall Cable Electrical Access Allows for easy cable access and power distribution installations Locking Safety Screws Prevent the flat panel from being removed or dislodged from the mount Use an optional Lock It security barrel for added protection Spring Lock Kickstand Simply push the mounting rails in to lock or unlock the mount from the closed position Prop up the flat panel with the kickstand for easy maintenance Installation Instructions Visit the Premier Mounts website at http www mounts com Page 5 b 4 be LMVP Installation Introduction Directional Mounting Arrow The Directional Mounting Arrow stamped into the LMVP mount indicates which edge is the top Mounting Safety Two people are recommended to install the
13. m mounting brackets to the rails of the mount Installation Instructions Visit the Premier Mounts website at http www mounts com Page 11 Ua LMVP The locking safety screws keep the flat panel from being accidently dislodged from the LMVP Locate the pre installed security locking safety screw at the bottom of each of the mounting brackets Use the Allen key supplied to tighten the locking safety screw Pre installed Security Locking Safety Screw 1 per Bracket A Do not overtighten the locking safety screws Proceed to the Post Installation Adjustments below Post Installation Adjustments The LMVP has a set of post installation adjustments on each mounting bracket Figure 1 See Note Use Allen key supplied to fine tune adjust See Note Make sure the locking safety screws are loosened before making adjustments Note Screws have a limited travel adjustment Do not overtighten or over adjust the screw to avoid damage to threaded holes Figure 1 Move Inward Left Control Right Control Move Outward fin Ff Left Control Right Control Page 12 Visit the Premier Mounts website at http www mounts com Installation Instructions LMVP Post Installation Adjustments cont d Tilt Left A Left Control Tilt Right f OUT Left Control Tilt Up Left Control fo TILT Left Control Insta
14. n be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 1321 S State College Blvd Fullerton CA 92831 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Contact Us WORLD HEADQUARTERS 1321 S State College Blvd Anaheim CA 92831 USA USA and Canada Phone 1 800 368 9700 Fax 1 800 832 4888 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2011 Installation Instructions Visit the Premier Mounts website at http www mounts com Page 17
15. signed to accommodate the various M4 M5 M6 and M8 hole sizes required by flat panels Do not place excessive pressure on the back of the flat panel as this may damage your flat panel The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown Does your flat panel have Recessed mount points Uneven mount points A curved back Any obstruction near the mount point If Yes you must install Universal Spacers Remove the mounting brackets Universal Washers and mounting screws from the back of the flat panel Proceed to the Universal Spacer Installation section If No skip to the Attaching the Mounting Bracket to the Flat Panel section Universal Spacer Installation Premier Mounts Universal Spacers allow you to attach the mounting bracket to flat panels which have recessed or uneven mount points Each Universal Spacer adds 1 4 to the distance between the mounting bracket and your flat panel Mounting Screw Universal Washer The Universal Spacers must be stacked and Mounting Bracket oriented as shown The Universal Spacers must only be installed between the mounting bracket and your flat panel Flat Panel Proceed to the Attaching the Mounting Bracket to Universal Spacer the Flat Panel section Mount Point a The Universal Spacers Fit M4 M5 M6 and M8 screw sizes Page 10 Visit the Premier Mounts website at
16. ur install direction corner register tabs of your mount You may use commercially available hardware to secure the spacer to the wall during installation depending on the wall material You may utilize the same spacer for multiple LMVP installations Register Tabs HO Register Tabs Multiple LMVP mounts can be installed using model specific spacers Simply repeat step one when installing each of the surrounding LMVP mounts Use one spacer for each 2x2 installation by mounting it to the wall or utilize the same spacer as many times needed to complete an unlimited LMVP large matrix video wall 1 Make sure the spacer is plumb and level and mark each corner where the LMVP will be mounted or secure to the wall It is best to start from the bottom corner and work your way up Install the second mount working in a horizontal direction Ensure that the mount remains plumb and level Repeat this step for each mount horizontally To install multiple rows place spacer between previously installed LMVPs on the bottom row Make sure the spacer is plumb and level mark the corners or secure to the wall to be sure of where the LMVP should be and secure your mount to the wall Page 8 Visit the Premier Mounts website at http Awww mounts com Installation Instructions LMVP P2 Installing the Mounting Brackets Selecting the Mounting Hardware 1 Inserta small straw or toothpick into the threa
Download Pdf Manuals
Related Search