Netis System ST3116 network switch
Contents
1. f The switch is powered off The corresponding port is conne On cted to a network device LINK ACT Data is transmitting through the 1 5 8 LAN1 LANS Flashing corresponding port LAN8 1X 16X 24X No device is connected to the Off corresponding port There is a 100Mbps 1000Mbps device Flashing connected to the corresponding port 100M 1000M There is a 10Mbps 10 100Mbps device or connected to the corresponding port or there is no device connected to the corresponding port There s a PoE PD Power Device On connected to the corresponding port which supply the power successfully No PoE PD is connected to the corresponding port or no power is supplied according to the power limits of the port Off The power of all the connected PoE ports is gt 60W 120W No power On may be supplied if additional PDs PoE MAX are connected for PE6108GH PE6108G The power of all the connected PoE ports is lt 60W 120W or there is no PoE PD connected to the corres ponding port Off netis Unmanaged Switch Quick Installation Guide Troubleshooting 1 The Power PWR LED is not on gt Check if the Power Adapter Power Cord is well connected Try to unplug and plug back in the Power Adapter Power Cord to the switch or try another power outlet 2 The LINK ACT LED is not on gt Make sure the network configuration of connecting device is correct and network card and d2. ion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help For ST3108G ST3116 ST3124 ST3116P ST3124P ST3116G ST3124G PEG108 PE6108H PEG108GH PE6108G This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense Warning A shielded type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception Itis essential that only the supplied power cord be used Use only shielded cables to connect I O devices to thi
3. netis Unmanaged Switch Quick Installation Guide netis Unmanaged Switch Quick Installation Guide The Switch mentioned in this Quick Installation Guide stands for netis 100Mbps amp 1000Mbps unmanaged switches including models ST 3105 ST 3108 ST3105S ST3108S ST3105G ST3108G ST3116 ST3124 T3116P ST3124P ST3116G ST3124G PE6108H PE6108 PE6108GH PE6108G etc For simplicity we take ST3105S as an example of the product images below Hardware Installation Power Adapter Computer ADSL Router e ian HE m Connect one of the Ethernet ports on the switch to your router s LAN port with an Ethernet cable 2 Connect your computer to one of the other ports on the switch with an Ethernet cable 3 Plug the provided Power Adapter Power Cord into the power jack of netis switch and the other end to a standard electrical socket netis Unmanaged Switch Quick Installation Guide LED Indicators The LED Indicators will allow you to monitor diagnose and troubleshoot any potential problem on the switch connection and attached devices Not all the LED indicators in the following table are included on one switch Please refer to the panel of your switch LED Status Indication On The switch is powered on PWR Of
4. rivers are installed correctly gt Check the cable connections gt Make sure the cable distance between the switch and other IEEE802 3 compatible network device does not exceed 100 meters 3 Performance is bad gt Check the status of Ethernet switching If Ethernet switching is set to full duplex on one device but a partner is set to half duplex then performance will be poor gt Make sure the cable between the switch and other IEEE802 3 compatible network device is Category 5 UTP or better 4 Some devices can t talk to other devices on the network gt Check status of the LINK ACT LEDs to make sure devices are linked gt Make sure that the devices network configurations are correct gt Reset the switch if needed Appendix A FCC Statement FCC Statement For ST 3105 ST 3108 ST3105S ST3108S ST3105G This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recept
5. s equipment You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment depend on EUT condition This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference thatmay cause undesired operation Appendix B Industry of Canada Statement For ST3105S ST3108S ST3105G This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada For ST3108G This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada Technical Support USA Canada Toll Free 1 866 71 network 1 866 716 3896 E mail usa_support netis systems com Other Regions E mail support netis systems com NETIS SYSTEMS CO LTD www netis systems com MADE IN CHINA zzesownyd
Download Pdf Manuals
Related Search