Hunter 59033 fan
Contents
1. 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Auto Resume Feature This fan contains a receiver with an auto resume feature The receiver remembers the intensity of the light speed and direction of the fan and whether the heater is on or off When power is restored to the receiver the fan light and heater will be at the previous settings Heater Operation The heater button is used to turn on and off the heater e Press the heater button 1 time to turn the heater on e Press the heater button again to turn the heater off Note Regardless of the speed setting on the fan when the ceiling fan is operating and the heater function is turned ON the ceiling fan automatically switches to low speed updraft only and will not accept any commands from the remote until the heater is turned off www HunterFan com 1 888 830 1326 Maintenance amp Cleaning Threaded Portion of Heater Vent Glass Bowl Finial Reverse Switch Changing the bulbs unscrew the Changing the direction of air Cleaning the fan use soft finial and remove it from the heater flow press the reverse switch brushes or cloths to prevent vent while supporting the glass scratching Cleaning products bowl with your other hand Carefully may damage the finishes remove the glass bowl Unscrew bulbs and replace with bulbs of same type and wattage Reinstall the glass bowl assembly2. M3514 01 02 19 13 Hunter Fan Company Troubleshooting www HunterFan com 1 888 830 1326 Fan doesn t work Excessive wobbling Noisy Operation Lights dim when turned on or e Make sure power switch is on e Tighten all of the blade and e Tighten the blade and blade do not turn on at all l blade iron screws until they iron screws until they are snug e Make sure the wattage of the Pull the pull chain to make sure are snug light bulbs installed matches it is on e Check to see if any of the the specifications on the light l l e Turn the power off support blades are cracked If so replace sockets Push the motor reversing switch the fan carefully and check all of the blades firmly left or right to ensure that that the hanger ball is it is engaged properly seated Check the circuit breaker to Use the provided balancing ensure the power is turned on kit and instructions to balance Make sure the blades spin freely the fan Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on page 10 Check the plug connection in the switch housing M3514 01 02 19 13 Hunter Fan Company
3. equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment ships at sea or other critical navigation or communications equipment operating between 0 45 30 MHz This device complies with Part 18 of the FCC Rules Tools Needed www HunterFan com 1 888 830 1326 amp LI Ladder L Pliers L Wire Strippers E Power Drill 9 64 Drill Bit optional optional If mounting to a support structure you will also need these tools M3514 01 02 19 13 Hunter Fan Company 3 4 CEILING a P Mounting Options www HunterFan com 1 866 268 1936 f ka ea a ra ka ea ra a ra e o N o o O a egoe U s If you have a flat ceiling Hang your fan by a standard downrod included Standard Support Support Mounting Structure T O If you have an angled ceiling InN 0 1 You will need a longer downrod sold separately Outlet Box 2 If your ceiling angle is greater than 34 y
4. Note For rocker style cover plates break off the tabs by pushing outward Remote Control continued Heater Reverse Switch CAUTION e Always AR the correct size and grade of battery most suitable for the intended use e Clean the battery contacts and also those of the device prior to battery installation e Ensure the batteries are installed correctly with regard to polarity and e Remove batteries from equipment which is not to be used for an extended period of time e Remove used batteries promptly Fan Operation To start the fan press the speed button on the remote at the level you desire 3 for high 2 for medium e 1 for low To turn off the fan press 0 Light Operation The light button is used to turn on dim and turn off the light To Turn the light on e Press the light button 1 time and the light will come on to the previously set level To dim the light e Press and hold the light button until the light has reached the desired level As you hold the button the light level will move throughout its entire range within 16 seconds Release the button at the desired level To Turn the light off e Press the light button 1 time for gradual off and the light will dim automatically for approximately 20 seconds until all the way off to allow for safe exit from the room e Press the light button 2 times or 1 time while the light is dimming for instant off M3514 01 02 19
5. Table of Contents Congratulations on purchasing your new Hunter ceiling fan It will provide comfort and performance in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world To register your fan please visit www HunterFan com register Save your receipt for proof of purchase Blades Switch Housing D 7 What to Expect with Your Installation Tools Needed M3514 01 02 19 13 Hunter Fan Company www HunterFan com GY Mounting Options Maintenance amp Cleaning Ceiling Bracket 080901326 1 888 830 1326 What to Expect with Your Installation Must be able to secure the fan to building structure or fan rated outlet box You may need a friend to help you Check box to see fan weight If you are unfamiliar with wiring use a qualified electrician D Know your wiring Ceiling angles greater than 34 will require an Angled Mounting Kit See page 4 for details a Assess ceiling angle 30 inches from blade tip to nearest wall or obstruction 7 feet from bottom edge of blade to the floor A Assess location Standard Downrod for ceilings 8 10 feet h
6. bel your remotes to ensure you do not mix them up 1 At the circuit breaker or fuse box turn the power off for the fan you want to change Do not turn the power off at the circuit breaker for the previously installed fan as you may inadvertently change the DIP switch code settings for it as well 2 Slide the cover off the back of the remote and remove the battery The battery must be removed when changing DIP switch settings 3 Change the DIP switch settings so that they are different from the previously installed fan 4 Replace the battery and cover 5 At the circuit breaker or fuse box turn the power back on for the fan whose settings you are changing 6 Within 20 seconds of restoring power push the 3 high 2 medium and 1 low buttons in that order on the remote Note The receiver built into the fan has a memory function that retains the last DIP switch code setting The setting will not change in the event of power failure or if the power to the fan is inadvertently shut off M3514 01 02 19 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Removed Rocker Tabs Style Plate To install the transmitter cradle remove the two screws holding the switch cover plate Do not remove the cover plate Orient the cradle by lining up the two mounting holes with those on the cover plate Insert and tighten the screws Do not over tighten
7. f the downrod HAND TIGHTEN If the setscrew is not tightened securely the fan may fall M3514 01 02 19 13 Hunter Fan Company Downrod continued www HunterFan com 1 888 830 1326 Put the wires and downrod through the DO NOT PICK THE FAN UP BY THE canopy Let the canopy sit loosely on top CANOPY OR WIRES Place the downrod of the fan ball into the slot in the ceiling bracket M3514 01 02 19 13 Hunter Fan Company GE N q 4 l www HunterFan com 1 888 830 1326 Note To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight J Buipuno1p ads MojjaX uaas6 Using an orange wire connector from the X hardware bag connect the black wire ungrounded from the ceiling to the black wire from the receiver Connect the white wire grounded from the ceiling to the white wire from the receiver Using an orange wire connector from the amp hardware bag connect the 3 grounding wires green green yellow stripe or bare copper coming from the ceiling downrod and hanging bracket papunosb asym papunosbun y2ejq green yellow stripe ads Mo jah uaasbH Turn the splices upward and push them carefully back through the hanger bracket into the outlet box Spread the wires apart with the grounded wires on one side of Refer to CAUTION c 1 on pg 2 the outlet box and the ungrounded wires on the other side of the out
8. igh Shorter Downrod for fans installed close to ceiling Longer Downrod for ceilings 10 feet or higher a Select a downrod length 2 M3514 01 02 19 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Read and Save These Instructions This product conforms to UL Standard 507 WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Hunter Solid State Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Hunter replacement parts This
9. lbs to replace your light bulbs Your lights may flicker or fail to work Note Globe style and number of lights may vary Threaded Portion of Heater Vent Glass Bowl Finial Place the glass bowl over the heater vent ensuring the threaded portion of the heater vent comes out of the bottom of the glass bowl Place the finial over the threaded portion of the heater vent and twist it to tighten it against the glass bowl M3514 01 02 19 13 Hunter Fan Company www HunterFan com 1 888 830 1326 See next page for fan operation instructions Note In compliance with US federal energy regulations this ceiling fan contains a device that restricts its light output Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket s may result in fire hazard or improper operation Remote Control lt switches Install one 1 12 Volt type 23A MN 21 battery included into the transmitter Clean the battery contacts and also those of the device prior to battery installation Ensure the battery is installed correctly with regard to polarity and Please contact your local battery recycling center for proper battery disposal information Setting the DIP switches You will only have to change the DIP switch settings in the remote if you are using more than one remote controlled fan in the same area and want to control them separately You may want to la
10. let box M3514 01 02 19 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Position the canopy so that when Lift the canopy into place so that Insert the two canopy screws lifted into place the canopy fits into the screw holes are aligned found in the hardware bag the hanging bracket as shown Note Fan style may vary f M3514 01 02 19 13 Hunter Fan Company i Blades www HunterFan com 1 888 830 1326 Remember the screws that you kept after removing the shipping blocks page 6 You need them for this step Insert grommets found in the W hardware Lightly attach the blade irons to the bag into the holes in the blades then motor with the blade iron armature secure each blade to a blade iron with screws then securely tighten after both screws found in the A hardware bag screws are attached Your blades are shielded with Dust Armor which is ananotechnology coating that repels dust For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning agents may damage the finishes M3514 01 02 19 13 Hunter Fan Company 1 888 830 1326 w found in www HunterFan com hardware bag into place and then tighten all three 3 screws Insert the third scre T R LAAAAALALALALAS i secure all 3 assembly screws could result in the switch attached to the mounting plate Fail
11. ling Bracket continued Preparation Time Saver Tip Get a helper to insert grommets found in the W hardware bag into the blades while you re doing the next couple of steps M3514 01 02 19 13 Hunter Fan Company www HunterFan com 1 888 830 1326 er tL TD O ENN So NS V A NNR 1 A 1 fief ax Ss 1 A A Remove the shipping blocks from the motor Save the screws They will be needed for blade iron installation Note Some fans will have a shipping ring instead of shipping blocks Please remove the ring and save the screws Downrod www HunterFan com 1 888 830 1326 Standard Downrod skip to next page for ceilings 8 10 high If you need a different downrod length follow these steps Longer Steps 1 5 to remove standard downrod pipe Downrod for angled ceilings or ceilings 10 or higher Included pre assembled Shorter Downrod for fans installed close to ceiling Included Sold Separately Steps 6 10 to reassemble with new pipe M3514 01 02 19 13 Hunter Fan Company Downrod continued www HunterFan com 1 888 830 1326 T U YN O O j il Remove the pre installed setscrew so that the downrod can be inserted Hand tighten the downrod at The wires can be cut but Tighten the setscrew least 4 5 full turns until it stops leave at least 8 extending with pliers DO NOT from the top o
12. ou will Angled Ceilin required also need an Angled Mounting Kit sold separately Mounting N Outlet e required Mounting Use the three steps below to determine if your ceiling angle is greater than 34 Use Standard Mounting Use Angled Mounting BOTH Ceiling amp Wall or Low Profile Mounting to hang the fan from a You need ONLY to hang the fan from a flat ceiling vaulted or angled ceiling a Longer Downrod most common Mounting Kit M3514 01 02 19 13 Hunter Fan Company Ceiling Bracket Make sure all four 4 bumpers are still attached To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location www HunterFan com 1 888 830 1326 Use wood screws Use machine screws included when securing provided with outlet to support structure with box when securing to approved electrical outlet existing ceiling fan rated box Drill 9 64 pilot holes outlet box Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware foundin support of 31 8 kg 70 Ibs the hardware bag or less M3514 01 02 19 13 Hunter Fan Company For angled ceilings point opening toward peak If you are unable to do this call Technical Support at 1 888 830 1326 Refer to warning w 1 on pg 2 Cei
13. ure to properly housing fixture falling Make sure the upper switch housing is securely Pza the Wiss AA Q pi then wrap keyhole slots around the screws and e 02 19 13 Hunter Fan Company twist counterclockwise w ap ap U eD G ie 0 O ie 0 oF aD z eD is O ap ap LL hole of the upper switch housing M3514 01 A Z A T E Nene hardware bag halfway into the motor housing It does not matter Le N D IN Screw two 2 housing assembly screws which two screw holes you choose from the Switch Housing rad Light Kit lr Eea J Connect the plugs from the upper and lower switch housings Make sure to line up the colored markings on the connectors 50000000 8 z PA p Lift the lower switch housing up until its screw holes are aligned with the screw holes in the upper switch housing M3514 01 02 19 13 Hunter Fan Company www HunterFan com 1 888 830 1326 uy Pza Install the three switch housing screws found in the hardware bag Make sure the lower switch housing is securely attached to the upper switch housing Failure to properly secure all three assembly screws could result in the light fixture falling Light Kit continued 00000000000000000000000000000000mm sa Install a light bulb in each socket Note Do not use CFL bu
Download Pdf Manuals
Related Search