Humminbird AD STM 7
Contents
1. to the water Small air bubbles can cling to the surface of the transducer and interfere with proper operation These bubbles will dissipate with time or you may wipe the face of the transducer with your fingers after the transducer is in the water 1 Year limited Warranty We warrant the original retail purchaser that products made by Humminbird have been manufactured free from defects in materials and workmanship This warranty is effective for one year from the date of original retail purchase Humminbird products found to be defective and covered by this warranty will be replaced or repaired free of charge at Humminbird option and returned to the customer freight prepaid Humminbird sole responsibility under this warranty is limited to the repair or replacement of a product that has been deemed defective by Humminbird Humminbird is not responsible for charges connected with the removal of such product or reinstallation of replaced or repaired parts NOTE The transducer must be submerged in water for reliable transducer detection This warranty does not apply to a product that has been e Improperly installed e Used in an installation other than that recommended in the product installation and operation instructions e Damaged or has failed because of an accident or abnormal operation e Repaired or modified by entities other than Humminbird Please retain your original receipt as a proof of the purchase date Th2. 008 Humminbird Eufaula AL USA All rights reserved Trolling Motor Mounted Transducer with Mount Assembly 2 Position the transducer on the underside of the motor housing with the transducer end containing the mounting ears or mounting knuckle oriented away from the propeller NOTE Your transducer may not look exactly like the transducer shown in the illustration but it will mount in exactly the same way 3 Insert the hose clamp around the adapter bracket on the top of the transducer and pull the two ends up around the motor housing As you tighten the hose clamp check to make sure that the transducer is properly aligned with the motor housing 4 After tightening the hose clamp make sure that the transducer is securely attached to the motor housing and will not slip off while in operation Routing the Cable The transducer cable has a low profile connector which must be routed to the point where the fishfinder is mounted There are several ways to route the transducer cable to the area where the control head is installed NOTE Your boat may have a pre existing wiring channel or conduit that you can use for the transducer cable 1 Unplug the other end of the transducer cable from the control head Make sure that the cable is long enough to accommodate the planned route CAUTION Do not cut or shorten the transducer cable and try not to damage the cable insulation Route the cable as far as possible from any VHF radio antenna c
3. Trolling Motor Mounted Transducer with Mount Assembly Humminbird Service Policy Even though you ll probably never need to take advantage of our incredible service policy it s good to know that we back our products this confidently We do it because you deserve the best We will make every effort to repair your unit within three business days from the receipt of your unit at our factory This does not include shipping time to and from our factory Units received on Friday are typically shipped by the following Wednesday units received Monday are typically shipped by Thursday etc All repair work is performed by factory trained technicians to meet exacting factory specifications Factory serviced units go through the same rigorous testing and quality control inspections as new production units After the original warranty period a standard flat rate service charge will be assessed for each repair physical damage and missing parts are not included Any repairs made after the original warranty will be warranted for an additional 90 days after service has been performed by our factory technicians You can contact our Customer Resource Center or visit our website to verify the flat rate repair fee for your product visit the Product Support section http www humminbird com We reserve the right to deem any product unserviceable when replacement parts are no longer available or impossible to obtain This Service Policy is valid in the Un
4. ables or tachometer cables to reduce the possibility of interference If the cable is too short extension cables are available to extend the transducer cable up to a total of 50 For assistance contact the Customer Resource Center at www humminbird com or call 1 800 633 1468 for more information N Route the transducer cable around the side of the motor housing and secure it to the motor shaft using the plastic cable ties provided NOTE As you route the cable from the trolling motor to the boat be sure to leave sufficient slack in the cable to allow for full movement and retraction of the trolling motor during normal operation 3 Route the transducer cable to the fishfinder Connecting the Cable Insert the transducer cable into the appropriate terminal slot The cable connectors are labeled and there are corresponding labels on the cable holder on the rear of the fishfinder The slots are keyed to prevent reversed installation so be careful not to force the connector into the holder Refer to your manual and or control head installation guide for the correct procedure for installing the cable connectors to the fishfinder 1 Plug the other end of the transducer cable back into the control head connection holder 930503 5_B Assembling the AD STM Assembling the AD XTM9 2008 Humminbird Eufaula AL USA All rights reserved Trolling Motor Mounted Transducer with Mount Assembly Test and Finish the Installati
5. is will be required for in warranty service THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD AND WILL BE THE CUSTOMER S EXCLUSIVE REMEDY EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE IN NO EVENT WILL HUMMINBIRD BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS Some states do not allow limitations on an implied warranty or the exclusion of incidental or consequential damages so the above exclusions may not apply to you You may also have other rights which vary from state to state 2008 Humminbird Eufaula AL USA All rights reserved
6. ited States only This applies only to Humminbird products returned to our factory in Eufaula Alabama This Service Policy is subject to change without notice DOMESTIC USA CUSTOMERS PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE For all technical issues please call 1 800 633 1468 Or visit www humminbird com click SUPPORT Please reference product serial number and model number when contacting Humminbird Returning Your Unit for Service Before sending your unit in for repair please contact the factory either by phone or by email to obtain a Repair Authorization Number for your unit NOTE Please do not return your Humminbird to the store for service Please have your product model name and serial number available before calling the factory If you contact the factory by e mail please include your product model name and serial number in the e mail and use Request for Repair Authorization Number for your e mail subject header You should include your Repair Authorization Number in all subsequent communications about your unit For IN WARRANTY service complete the following steps e Obtain a Repair Authorization Number from the Humminbird Customer Resource Center e Tag product with your name street address phone number and your assigned Repair Authorization Number Include a brief written description of the problem Include a copy of your receipt to show proof and date of purchase e Return product f
7. ities of your Humminbird product NOTE Your transducer may not look exactly like the transducer shown in the illustrations but it will mount in exactly the same way Your Humminbird accessory is designed for trouble free use in even the harshest marine environment In the unlikely event that your Humminbird accessory does require repairs we offer an exclusive Service Policy free of charge during the first year after purchase and available at a reasonable rate after the one year period For complete details see the Warranty section included in this manual Contact our Customer Resource Center at either 1 800 633 1468 or visit our website at www humminbird com Installation Overview Following are instructions for the installation of this accessory Before you start installation we encourage you to read these instructions carefully in order to get the full benefit from your Humminbird accessory If you find that any items are missing from your installation kit call our Customer Resource Center at 1 800 633 1468 or visit our website at www humminbird com In addition to the hardware supplied with your transducer you will need various hand tools Installation The trolling motor transducer is designed to mount on the trolling motor of your boat All hardware needed for installation and operation of this Humminbird accessory is either included with this accessory or came with your original transducer The trolling motor mounted
8. may change too quickly to allow time for you to react Always operate the boat at very slow speeds if you suspect shallow water or submerged objects WARNING Disassembly and repair of this electronic unit should only be performed by authorized service personnel Any modification of the serial number or attempt to repair the original equipment or accessories by unauthorized individuals will void the warranty Handling and or opening this unit may result in exposure to lead in the form of solder WARNING This product contains lead a chemical known to the state of California to cause cancer birth defects and other reproductive harm electrical and electronic equipment on human health and the environment Therefore any product bearing the WEEE symbol must not be included with unsorted municipal waste Instead it must be separately collected treated and recycled K The WEEE Directive aims to minimize the impact of end of life For proper disposal of this equipment please contact the Johnson Outdoors distributor or see www humminbird com 2008 Humminbird Eufaula AL USA All rights reserved Trolling Motor Mounted Transducer with Mount Assembly Thank You Thank you for choosing Humminbird America s 1 name in fishfinders Humminbird has built its reputation by designing and manufacturing top quality thoroughly reliable marine equipment Genuine Humminbird accessories offer the opportunity to upgrade and expand the capabil
9. on When you have installed both the fishfinder control head and the trolling motor transducer and have routed all the cables you must perform a final test to verify installation Testing should be performed with the boat in the water although you can initially confirm basic operation with the boat out of the water Routing the Cable Slack in Cable _ o 3 930503 5_B NOTE Make sure the trolling motor is re connected to the power source before performing this procedure 1 Press POWER once to turn the control head on If the unit does not power up make sure that the connector holder is fully seated in the receptacle and that power is available 2 Ifall connections are correct and power is available the Humminbird control head will enter Normal operation 3 Make sure that the boat is in water greater than 2 but less than the depth capability of the unit and that the ransducer is fully submerged since the sonar signal cannot pass through air If the bottom is visible on screen with a digital depth readout the unit is working properly Your control head is now ready for operation Maintenance If your boat remains in the water for long periods of time algae and other marine growth can reduce the effectiveness of the transducer Periodically clean the face of the transducer with hot water If your boat remains out of the water for a long period of time it may take some time to wet the transducer after it is returned
10. reight prepaid to Humminbird using an insured carrier with delivery confirmation 930503 5_B For OUT OF WARRANTY service complete the following steps e Obtain a Repair Authorization Number from the Humminbird Customer Resource Center e Include payment in the form of credit card number and expiration date money order or personal check Please do not send cash e Tag product with your name street address phone number and your assigned Repair Authorization Number e Include a brief written description of the problem e Return product freight prepaid to Humminbird using an insured carrier with delivery confirmation Contact Humminbird Contact the Humminbird Customer Resource Center in any of the following ways By Telephone Monday Friday 8 00 a m to 4 30 p m Central Standard Time 1 800 633 1468 By e mail typically we respond to your e mail within three business days cservice johnsonoutdoors com For direct shipping our address is Humminbird Service Department 678 Humminbird Lane Eufaula AL 36027 USA WARNING Do not touch an active transducer during operation as this may cause physical discomfort and may result in personal injury in the form of tissue damage Handle the transducer only when the power to the fishfinder is off WARNING This device should not be used as a navigational aid to prevent collision grounding boat damage or personal injury When the boat is moving water depth
11. transducer allows you to gather sonar information from the point on the boat closest to where you are fishing It is important that you properly orient the transducer housing in the direction of travel of the trolling motor to ensure an accurate depiction of the terrain under your boat The trolling motor mounted transducer will fit any standard trolling motor housing Some users install this transducer in conjunction with a switch so that the standard transducer can be used for high speed operation and the trolling motor transducer can be used while trolling Attaching the Transducer WARNING Before attaching the transducer to the trolling motor make certain that the motor is disconnected from all sources of electrical power CAUTION Before attaching the transducer to the trolling motor make sure that the trolling motor is properly secured to the boat and will not shift during transducer installation 1 Attach the transducer to the bracket using the hardware provided and refer to the illustration that matches your transducer type NOTE If you purchased the AD STM or AD XTM 9 accessory you will need to use the hardware that originally came with the transducer to attach the transducer to the bracket Mounting Bracket should be parallel to the Transducer Side View f the Transducer 930503 5_B Trolling Motor Mount Installation Assembling the Metal Mounting Bracket Assembling the Metal Mounting Bracket 2
Download Pdf Manuals
Related Search