Diablotek International PSDA250 power supply unit
Contents
1. 5 OiSoO0LOTEK POWER SUPPLY INSTALLATION 6 Close your computer case connect the power cord to the power supply unit and then set the I O switch of the power supply unit to I position 7 You are now ready to start your computer Connect the power cord to the power supply unit amp power outlet digbLoTeKk m g OUTPUT SPECIFICATION 20 24 PINMOTHERBOARD CONNECTOR Voltage Color Color Voltage Ce MOTHERBOARD 4 sv Red a 16 Green Psong sv Red 6 18 Black COM PWR ON Gray 8 20 NC 5Vsb Purple 9 21 Red 5v 32V Yellow 10 Red 45V 12V Yellow 11 23 Red 45 6 8 PIN PCI EXPRESS CONNECTOR 2 Hn Black Detachable Black Yellow Black ak com a Yellow Black 12V 6 com 6 o 8 x N 4PIN Detachable O 20 PIN a MN Q 4 O1 O Oo CO Yellow AxN Yellow 12V 8 OUTPUT SPECIFICATION 4 PIN MOLEX CONNECTOR SATA CONNECTOR Color Signal Pin Red 5voc a Color Signal Pin COM 2 EA ac COM E DA series 20 24PIN 6PIN 6 2P 8P AP CPU 12V 4 4P CPU 12V CONNECTOR MAINBOARD PCI EXPRESS PCI EXPRESS MOLEX SATA FDD TYPE CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR IC EI CI A E mme e e ps 1 ES pe x o IE 2 o oo 0 os2. MICRO ATX ATX POWER SUPPLY la pg 14 USER MANUAL TABLE OF CONTENTS OAR Components Check samme eee a ete E ee ane E ES RE eee eee er ee ewer eee eres p 2 QAAE IIR TTE To e A p 2 03 Existing Power Supply Removal p 3 04 Power Supply Installation lt a A ee p 4 OSZOUtp tSpeciicationt c SE e E eee p 7 06 Connectors p 9 07 Trouble Shooting p 11 08 Warranty p 12 COMPONENTS CHECK Sy ee x X X Diablotek ATX Power Supply AC Power Cord Screw Pack User Manual Vibration Dampener WARNING amp CAUTION High voltages exists in the power supply DO NOT open the power supply case unless you are an authorized service technician Doing so will void the warranty DO NOT unplug the AC power cord when the power supply is in use Warranty is void if the cover is removed Please keep the power supply away from humidity and operate it in the proper environment The PSU should be powered by the source indicated on the rating label EXISTING POWER SUPPLY REMOVAL 1 Disconnect your PC from all AC sources Make certain the system is turned OFF If applicable put the power supply unit s AC power switch to O off position 2 Open the PC case and if applicable refer t
3. ly and do not cover items out of production if the company no longer stocks them This warranty is not assignable Third party products such as motherboards and other system components using or interacting with the DIABLOTEK products are not covered by this warranty DIABLOTEK s sole obligation under this warranty is to replace or at its option to repair free of charge all the product s defective parts This warranty applies only on the condition that the product has been installed maintained and operated under conditions of normal use and in accordance with the installation guide provided The provisions of this warranty shall not apply if in DIABLOTEK s sole judgment the product has been subject to misuse or neglect improper installation damaged in an accident or repaired or altered in any way that affects its performance or reliability u un M nagd 1 4 Designed In USA Manufacture In China 2011 All rights reserved
4. o you PC manufacturer s User Manual 3 Carefully disconnect all power supply units DC wire harness connectors from the main board and all peripheral connectors 4 Unscrew the mounting screws securing the power supply unit to the back of the PC case back panel 5 Carefully remove the power supply unit from the PC system POWER SUPPLY INSTALLATION 1 Make sure that your system is turned off and unplugged Disconnect the AC power cord from your old power supply 2 Open your computer case please refer to the direction in your case manual 3 Disconnect all power connectors from the devices 4 Remove the old power supply and replace the new one into your computer case Remove the old power supply unit 1B Install the New power supply unit S CIBOLOTEIC it POWER SUPPLY INSTALLATION 5 Connect power connectors to your motherboard and peripheral devices A Connect the 24PIN Main Power Connector to your motherboard If your motherboard uses a 20PIN connector detach the 4PIN attachment on the 24PIN connector B Connect the 4 8PIN 12V Power Connector for the CPUs C Connect the Peripheral 4PIN power Connector to devices SATA connectors are for devices with Serial ATA interface D Connect the Y type Floppy Drive Power Adapter to the floppy as needed E Connect the PCI E 12V Power Connector s to the PCI E graphics card s Please consult your graphics card manual for details if needed PG
5. oa e E wem Lo x p ow j 5 EBEN eee a al ERE CN CONNECTORS PHD series P m E 20 24 4 4P CPU 12V CONNECTOR MAINBOARD PCI EXPRESS TYPE CONNECTOR CONNECTOR CONNECTOR 6 2P 8P PCI EXPRESS CONNECTOR MOLEX TROUBLESHOOTING If the power supply unit fails to function properly please check the following items before submit ting application for repair 1 Ensure that the power cord plugged properly into the electrical outlet and into the power supply AC inlet 2 Ensure that the I O switch on the power supply unit is switched to I position 3 Check that all power connectors are properly connected to all the devices 4 Please turn off and turn on the power supply with the I O switch a few times with at least 0 5 second in the off state to reset the power supply unit If the power supply is still unable to function properly after above instructions please contact diablotek s website at www diablotek com or contact our direct Tech support number at 626 771 3230 for more technical support solution 3 YEAR WARRANTY DIABLOTEK offers a 3 YEARS warranty for all DIABLOTEK DA PHD series power supply unit limited to those residing in 48 continental US states and Canada DIABLOTEK warrants the products to be free from defects in materials and workmanship for the products as sold to the original purchaser This warranty is for replacement for like items on
Download Pdf Manuals
Related Search