Kramer Electronics TP-121EDID
Contents
1. acquire the EDID from the display or set the system to the default EDID see Section 9 To connect the PT 110EDID with the TP 120 as the example in Figure 10 illustrates do the following 1 On the PT 110EDID connect the XGA source for example the 15 pin HD output from a computer s graphics card to the XGA INPUT 15 pin HD F connector 2 On the TP 120 connect the XGA OUT 15 pin HD F connector to the XGA acceptor for example a monitor TP 121 3 5EDID PT 110EDID Your PT 110EDID 3 Connect the LINE OUT RJ 45 connector on the PT 110EDID to the LINE IN RJ 45 connector on the TP 120 via CAT 5 cabling CAT 5 cable has a range of greater than 300ft gt 100m For details of how to wire a CAT 5 LINE IN LINE OUT RJ 45 connector see Section 8 4 On both the PT 110EDID and the TP 120 connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity For distances of up to 100 meters you can connect a power adapter to either the PT 110 or TP 120 Above it both sides should be fed with power 5 On the TP 120 adjust the output signal level and or cable compensation equalization level if required Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level 6 If necessary set the H SYNC and V SYNC switches on the units By default both switches are set for normal H SYNC and V SYNC polarity Long CAT 5 cable PT 110EDID Computer Graphics So2. XGA Audio Data Line Transmitter 5 3 Connecting the RS 232 Port To control an RS 232 controllable remote device from a PC or RS 232 controller prepare an RS 232 cable with a 9 pin D sub connector at one end and a 2 pin terminal block connector at the other end as shown in Figure 5 14 TP 121 3 5EDID PT 110EDID Your TP 123EDID PC Controller to TP 123EDID TP 124 to Controlled Unit PIN 5 Connected to GND PIN 5 Connected to GND PIN 3 Connected to RxD PIN 2 Connected to TxD To PC 9 pin D sub To PC 9 pin D sub Figure 5 RS 232 PINOUT Connection Connect this PIN on To this PIN on the the Terminal Block 9 pin D sub Connector Connector feo m mo ns 5 4 Technical Specifications TP123EDID INPUTS Video 1 VGA UXGA on a 15 pin HD connector Audio 1 audio ANALOG 3 5mm mini jack 1 RJ 45 OUT connector RS 232 2 pin terminal block RS 232 BAUD RATE Up to 19200kbps BANDWIDTH 3dB Audio 20Hz to 20kHz 0 5dB RESOLUTION Up to WUXGA and 1080p S N RATIO Video 58dB unweighted 68 3dB 5MHz weighted Audio lt 80dB DIMENSIONS 12 1cm x 7 18cm x 2 42cm 4 76 x 2 83 x 0 95 W D H 0 3kg 0 6715 approx ACCESSORIES Power supply AKT 19 rack adapter All measurements are based on the transmitter receiver pair Specifications are subject to change without notice at http www kramerelectronics com TP 121 3 5EDID PT 110EDID Your TP 123EDID Seal 6 1 Your TP 125EDID This section describes
3. complete list of Kramer cables is on our Web site at http www kramerelectronics com 2 On the TP 122N connect the XGA OUT 15 pin HD F connector to the XGA acceptor for example a display AUDIO OUT S PDIF RCA connector to the digital audio acceptor for example an AV receiver ANALOG 3 5mm mini jack to the analog audio acceptor for example a stereo audio recorder 3 Connect the LINE OUT RJ 45 connector on the TP 121EDID to the LINE IN RJ 45 connector on the TP 122N using CAT 5 cabling CAT 5 cable has a range of greater than 300ft gt 100m For details of how to wire a CAT 5 LINE IN LINE OUT Ru 45 connector see Section 8 4 Connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity on both the TP 121EDID and the TP 122N If you cannot connect the power to both the TP 121EDID and TP 122N connect the power only to any one unit 5 On the TP 122N Adjust the video output signal level and or cable compensation equalization level if required Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level f necessary set the H SYNC and V SYNC switches on the underside By default both switches are set down for negative V SYNC and H SYNC polarity TP 121 3 5EDID PT 110EDID Your TP 121EDID a Computer N Graphics Source TP 121EDID S 1V9 Q 7 Display Stereo Audio Recorder AV Receiver Figu
4. power adapter to the transmitter and plug the adapter into the mains electricity Step 5 Operate the Product To capture the EDID press the CAPTURE button Contents Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Safety Instructions 2 3 Recycling Kramer Products 3 Overview 3 1 About Shielded Twisted Pair STP Unshielded Twisted Pair UTP 3 2 About the Power Connect Feature 4 Your TP 121EDID 4 1 Overview 4 2 Connecting the TP 121EDID XGA Audio Line Transmitter 4 3 Technical Specifications TP 121EDID 5 Your TP 123EDID 5 1 Overview 5 2 Connecting the TP 123EDID XGA Audio Data Line Transmitter 5 3 Connecting the RS 232 Port 5 4 Technical Specifications TP123EDID 6 Your TP 125EDID 6 1 Overview 6 2 Connecting the TP 125EDID XGA Audio Data Line Transmitter 6 3 Connecting the RS 232 Port 6 4 Technical Specifications TP 125EDID 7 Your PT 110EDID 7 1 Overview 7 2 Connecting the PT 110EDID XGA Line Transmitter 7 3 Technical Specifications PT 110EDID 8 Wiring the TP LINE IN LINE OUT RJ 45 Connectors 9 Acquiring the EDID Figures Figure 1 TP 121EDID XGA Audio Line Transmitter Figure 2 Connecting the TP 121EDID XGA Audio Line Transmitter Figure 3 TP 123EDID XGA Audio Data Line Transmitter Figure 4 Connecting the TP 123EDID XGA Audio Data Line Transmitter Figure 5 RS 232 PINOUT Connection Figure 6 TP 125EDID XGA Audio Data Line Transmitter Figure 7 Connecting t
5. the TP 125EDID XGA Audio Data Line Transmitter Overview The TP 125EDID is a high performance XGA stereo audio line transmitter It inputs an XGA signal up to WUXGA 1080p unbalanced stereo audio signal and bidirectional RS 232 control commands and transmits them over CAT 5 cable to a receiver for example the Kramer TP 126 UXGA Audio Data Line Receiver It converts the unbalanced stereo audio signal to a digital audio S PDIF stream before transmitting to preserve the quality of the audio signal Commands and data can flow in both directions via the RS 232 interface allowing status requests and control of the destination unit The TP 125EDID includes H and V Sync internal polarity switches When the TP 125EDID is connected to a display device and the EDID CAPTURE button is pressed the TP 125EDID reads and stores the EDID Extended Display Identification Data from the display device The display can be disconnected and later reconnected without rebooting the operating system The TP 125EDID features e Amaximum resolution of WUXGA and 1080p e Atransmission range of more than 300ft 100m and a 20kHz audio bandwidth with an S N ratio that exceeds 80dB on the same transmission range e A bidirectional RS 232 port where commands and data can flow in both directions via the RS 232 interface allowing status requests and control of the destination unit e EDID Capture that copies and stores the EDID from a display device e 12V DC
6. this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the ori
7. transmits power to the receiving device or receives power from it over twisted pair cable e Hand V Sync polarity switches for improved display compatibility with the CAT 5 outputs e Is 12V DC fed Figure 9 defines the PT 110EDID 7 2 XGA INPUT 12V DC XGA Line Transmitter PT 110EDID Figure 9 PT 110EDID XGA Line Transmitter Feature Function ren IN 15 pin HD to the UXGA source Connector 2 12V DC 12V DC connector for powering the unit 3 EDID CAPTURE Button Press to acquire the EDID information from the display see Section 9 4 STATUS LED llluminates during normal operation flashes when acquiring the EDID 5 LINE OUT RuJ 45 Connects to the LINE IN RJ 45 connector on the TP 120 Connector UXGA Audio Line Receiver VS Switch Slide up to set the V SYNC to NEGATIVE polarity slide down to set the V SYNC to NORMAL polarity By default both switches are set down for normal V SYNC and H SYNC polarity 7 HS Switch Slide up to set the H SYNC to NEGATIVE polarity NEG slide down to set the H SYNC to NORMAL polarity By default both switches are set down for normal V SYNC and H SYNC polarity 8 ON LED llluminates when receiving power Connecting the PT 110EDID XGA Line Transmitter You can use the PT 110EDID XGA Line Transmitter together with the TP 120 XGA Line Receiverto configure an XGA to Twisted Pair transmitter and receiver system Before connecting the transmitter and receiver system you can
8. D CAPTURE button is pressed the TP 123EDID reads and stores the EDID Extended Display Identification Data from the display device The display can be disconnected and later reconnected without rebooting the operating system The TP 123EDID features e A maximum resolution of WUXGA and 1080p e A transmission range of more than 300ft 100m and a 20kHz audio bandwidth with an S N ratio that exceeds 80dB on the same transmission range e Aunidirectional RS 232 port for transmitting control commands e EDID Capture that copies and stores the EDID from a display device e The Power Connect Feature that transmits power to the receiving device or receives power from it over twisted pair cable e 12V DC power Figure 3 defines the TP 123EDID 5 2 XGA Audio Data Line Transmitter TP 123EDID Line OUT RS 232 Aupio IN 12V DC Figure 3 TP 123EDID XGA Audio Data Line Transmitter Feature Function _ CAPTURE Button _ to acquire the EDID information from the display 2 STATUS LED Illuminates during normal operation flashes when acquiring the EDID 3 ON LED Illuminates when receiving power 4 XGA IN 15 pin HD F connector Connect to the XGA source LINE OUT RJ 45 connector Connects to the LINE IN RJ 45 connector on the TP 124 XGA Audio Line Receiver Use a CAT 5 cable with RJ 45 connectors at both ends the PINOUT is defined in Section 8 RS 232 terminal block connector Connects to the PC or the Remote Controller se
9. DID PT 110EDID Introduction 2 2 1 Getting Started We recommend that you Unpack the equipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual Use Kramer high performance high resolution cables Go to http www kramerelectronics com to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate Achieving the Best Performance To achieve the best performance Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables Do not secure the cables in tight bundles or roll the slack into tight coils Avoid interference from neighboring electrical appliances that may adversely influence signal quality Position your Kramer products away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building TP 121 3 5EDID PT 110EDID Getting Started 2 2 2 3 3 5EDID PT 110EDID Getting Started Safety Instructions Caution There are no operator serviceable parts inside the unit Warning Use only the Kramer Electronics input power wall adapter that is provided with the unit Warning Disconnect the power and unplug the unit from th
10. KRAMER KRAMER ELECTRONICS LTD USER MANUAL MODELS TP 121EDID XGA Audio Line Transmitter TP 123EDID XGA Audio Data Line Transmitter TP 125EDID XGA Audio Data Line Transmitter PT 110OEDID XGA Line Transmitter P N 2900 000585 Rev 6 m TP 121EDID TP 123EDID TP 125EDID m PT 110EDID Quick Start Guide This guide helps you install and use your product for the first time For more detailed information go to http www kramerelectronics com support product_downloads asp to download the latest manual or scan the QR code on the left Step 1 Check what s in the box E TP 121EDID TP 123EDID a Rubber feet TP 125EDID and or PT 110EDID 1 Quick Start sheet XGA TP Transmitter 1 Power supply 12V DC Step 2 Install the TP 12xEDID PT 110EDID Attach the rubber feet and place on a table or mount the machine in a rack using an optional RK 3T rack mount for the TP 12xEDID units or an RK 4PT for the PT 110EDID Step 3 Connect the inputs and outputs TP 121EDID TP 123EDID 00000 0000 XGA IN RS 232 Aupio IN Line OUT Line OUT TP 125EDID PT 110EDID o Auoi0 IN 12V DC AuDIO IN PC TP 124 Control XGA INPUT 12V DC Vs Hs connec Norma ON olf HEBO Ser NEGATIVE PC TP 126 Control GA Line Transmitter PT 110EDID Step 4 Connect the power Connect the12V DC
11. Y APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome yo
12. ay The S PDIF audio OUT RCA connector to a digital AV receiver leave the ANALOG audio OUT 3 5mm mini jack unconnected An RS 232 cable with a 2 pin terminal block connector to the TP 124 RS 232 port and a 9 pin D sub connector to the RS 232 port on an RS 232 controllable device for example a switcher 3 Connect the Line OUT RJ 45 connector on the TP 123EDID to the LINE IN RJ 45 connector on the TP 124 via CAT 5 cabling CAT 5 cable has a range of greater than 300ft gt 100m For details of how to wire a CAT 5 LINE IN LINE OUT RJ 45 connector see Section 8 4 Connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity on both the TP 123EDID and the TP 124 If you cannot connect the power to both the TP 123EDID and TP 124 connect the power to any one unit 5 On the TP 124 Adjust the video output signal level and or cable compensation equalization level if required Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level 43 iw Z If necessary set the H SYNC and V SYNC switches on the underside By default both switches are set down for negative V SYNC and H SYNC polarity Computer Graphics a Audio RS 232 Control lt TP 123EDID Range gt 300ft gt 100 meters STP Cable Display RS 232 Controllable Device for example Switcher AV Receiver Figure 4 Connecting the TP 123EDID
13. densing DIMENSIONS 12 1cm x 7 18cm x 2 42cm 4 76 x 2 83 x 0 95 W D H WEIGHT 0 3kg 0 67lbs approx ACCESSORIES Power supply OPTIONS RK 3T 19 rack adapter All measurements are based on the transmitter receiver pair tested with 100m CAT 5 cable Specifications are subject to change without notice at http www kramerelectronics com TP 121 3 5EDID PT 110EDID Your TP 125EDID 7 1 Your PT 110EDID This section describes the PT 110EDID XGA Line Transmitter Overview The PT 110EDID is a high performance XGA line transmitter that inputs an XGA up to WUXGA 1080p signal and transmits it over CAT 5 cable to a receiver for example the Kramer TP 122N XGA Audio Line Receiver The PT 110EDID is pre programmed with default EDID information ready for the source even before capturing the EDID from the display When the PT 110EDID is connected to a display device and the EDID CAPTURE button is pressed the PT 110EDID reads and stores the EDID Extended Display Identification Data from the display device The display can be disconnected and later reconnected without rebooting the operating system The PT 110EDID features e Amaximum resolution of WUXGA and 1080p e Atransmission range of more than 300ft 100m and a 20kHz audio bandwidth with an S N ratio that exceeds 80dB on the same transmission range e EDID Capture that copies and stores the EDID from a display device e The Power Connect Feature that
14. e Section 5 3 7 AUDIO IN 3 5mm mini jack Connects to the audio source 8 12V DC 12V DC connector for powering the unit Connecting the TP 123EDID XGA Audio Data Line Transmitter You can use the TP 123EDID together with the TP 124 XGA Audio Data Line Receiver to configure a twisted pair transmitter and receiver system to transmit the video audio and RS 232 control signals via CAT 5 cable Before connecting the transmitter and receiver system you can acquire the EDID from the display or set the system to the default EDID see Section 9 TP 121 3 5EDID PT 110EDID Your TP 123EDID TP 121 3 5EDID PT 110EDID Your TP 123E To connect the TP 123EDID and the TP 124 as the example in Figure 4 illustrates do the following 1 On the TP 123EDID connect the XGA source for example a laptop s graphics card to the XGA IN 15 pin HD F connector Audio source for example the audio out of the PC to the AUDIO IN 3 5mm mini jack You can use a Kramer C GMA GMA cable VGA 15 pin HD M audio jack to VGA 15 pin HD M audio jack to make both connections on one cable Cables are not supplied The complete list of Kramer cables is on our Web site at http www kramerelectronics com RS 232 cable with a 9 pin D sub connector to the laptop and a 2 pin terminal block connector to the TP 123EDID RS 232 port as shown in Figure 5 2 On the TP 124 connect The XGA OUT 15 pin HD F connector to a displ
15. e wall before installing Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at http www kramerelectronics com support recycling 3 3 1 Overview This user manual describes the following devices e TP 121EDID XGA Audio Line Transmitter see Section 4 e TP 123EDID XGA Audio Data Line Transmitter see Section 5 e TP 125EDID XGA Audio Data Line Transmitter see Section 6 e PT 110EDID XGA Line Transmitter see Section 7 This section also describes e Using shielded twisted pair STP unshielded twisted pair UTP see Section 3 1 e The power connect feature see Section 3 2 About Shielded Twisted Pair STP Unshielded Twisted Pair UTP We recommend that you use Shielded Twisted Pair STP cable and stress that the compliance to electromagnetic interference was tested using STP cable There are different levels of STP cable available and we advise you to use the best quality STP cable t
16. ginal purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume a
17. hat you can afford Our non skew free cable Kramer BC STP is intended for analog signals where skewing is not an issue In cases where there is skewing our Unshielded Twisted Pair UTP skew free cable Kramer BC XTP may be advantageous and UTP cable might also be preferable for long range applications In any event when using UTP cable it is advisable to ensure that the cable is installed far away from electric cables motors and so on which are prone to create electrical interference 121 3 5EDID PT 110EDID Overview 3 2 3 5EDID PT 110EDID Overview About the Power Connect Feature The Power Connect feature applies as long as the cable can carry power This feature is available when using STP cable and the distance does not exceed 50m 164ft on standard CAT 5 cable For longer distances heavy gauge cable should be used TP cable is still suitable for the video audio transmission but not for feeding power at these distances For units that are connected via RJ 45 connectors make sure that the shield of the STP cable is connected to the metal casing of the connectors on both ends of the cable For units that are connected via terminal block connectors the shield of the STP cable must be connected to a ground terminal on the units at both ends Use the ground terminal of the power supply connection if necessary For a TP cable exceeding a distance of 50m separate power supplies should be connected to the transmitter and t
18. he TP 125EDID XGA Audio Data Line Transmitter Figure 8 RS 232 PINOUT Connection Figure 9 PT 110EDID XGA Line Transmitter Figure 10 Connecting the PT 110EDID XGA Line Transmitter Figure 11 TP PINOUT NOOO OR BP WWNDND Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront video audio presentation and broadcasting professionals on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters and GROUP 11 Sierra Video Products Thank you for purchasing your Kramer TOOLS TP 121EDID XGA Audio Line Transmitter and or TP 123EDID XGA Audio Data Line Transmitter and or TP 125EDID XGA Audio Data Line Transmitter and or Kramer Pico TOOLS PT 110EDID XGA Line Transmitter which are ideal for e Presentation and multimedia applications e Long range graphics distribution for schools hospitals security and stores E
19. ll risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If itis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons n
20. ng 1 On the TP 125EDID connect the XGA source for example a laptop s graphics card to the XGA IN 15 pin HD F connector Audio source for example the audio out of the PC to the AUDIO IN 3 5mm mini jack You can use a Kramer C GMA GMA cable VGA 15 pin HD M audio jack to VGA 15 pin HD M audio jack to make both connections on one cable Cables are not supplied The complete list of Kramer cables is on our Web site at http www kramerelectronics com An RS 232 cable with a 9 pin D sub connector to the laptop and a 3 pin terminal block connector to the TP 125EDID RS 232 port as shown in Figure 5 2 On the TP 126 connect The UXGA OUT 15 pin HD F connector to the AV display system The S PDIF audio OUT RCA connector to a digital AV receiver leave the ANALOG Audio OUT 3 5mm mini jack unconnected An RS 232 cable with a 3 pin terminal block connector to the TP 126 RS 232 port and a 9 PIN D SUB connector to the RS 232 port on the AV display system 3 Connect the Line OUT RJ 45 connector on the TP 125EDID to the LINE IN RJ 45 connector on the TP 126 via CAT 5 cabling CAT 5 cable has a range of greater than 300ft gt 100m For details of how to wire a CAT 5 LINE IN LINE OUT RJ 45 connector see Section 8 4 Connect the 12V DC power supply to the power socket and connect the adapter to the mains electricity on both the TP 125EDID and the TP 126 5 On the TP 126 Adjust the video output
21. o the receiver simultaneously 4 1 Your TP 121EDID This section describes the TP 121EDID XGA Audio Line Receiver Overview The TP 121EDID is a high performance XGA stereo audio line transmitter It inputs an XGA signal up to WUXGA 1080p and an unbalanced stereo audio signal and transmits them over CAT 5 cable to a receiver for example the Kramer TP 122N It converts the unbalanced stereo audio signal to a digital audio S PDIF stream before transmitting to preserve the quality of the audio signal When the TP 121EDID is connected to a display device and the EDID CAPTURE button is pressed the TP 121EDID reads and stores the EDID Extended Display Identification Data from the display device The display can be disconnected and later reconnected without rebooting the operating system The TP 121EDID features e A maximum resolution of WUXGA and 1080p e A transmission range of more than 300ft 100m and a 20kHz audio bandwidth with an S N ratio that exceeds 80dB on the same transmission range e EDID Capture that copies and stores the EDID from a display device e The Power Connect Feature that transmits power to the receiving device or receives power from it over twisted pair cable e 12V DC power Figure 1 defines the TP 121EDID 110EDID Your TP 121EDID rEDIDa ON Capture XGA Audio Line Transmitter Line OUT Aupio IN A 1 TP 121EDID XGA Audio Line Transmitter Feature Function m CAPTURE Bu
22. ot bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANT
23. power Figure 6 defines the TP 125EDID rEDIDs ON Status XGA Audio Data Line Transmitter TP 125EDID Line OUT RS 232 Avoio IN 12V DC Figure 6 TP 125EDID XGA Audio Data Line Transmitter Feature Function CAPTURE Button Le to acquire the EDID information from the display STATUS LED Illuminates during normal operation flashes when acquiring the EDID Illuminates when receiving power XGA IN 15 pin HD F connector Connect to the XGA source LINE OUT RJ 45 connector Connects to the LINE IN RJ 45 connector on the TP 126 XGA Audio Line Receiver Use a CAT 5 cable with RJ 45 connectors at both ends the PINOUT is defined in Section 8 RS 232 terminal block connector Connects to the PC or the Remote Controller see Section 5 3 7 AUDIO IN 3 5mm mini jack Connects to the audio source 8 12V DC 12V DC connector for powering the unit 6 2 Connecting the TP 125EDID XGA Audio Data Line Transmitter You can use the TP 125EDID together with the TP 126 UXGA Audio Data Line Receiver to configure a twisted pair transmitter and receiver system to transmit the video audio and RS 232 control signals via CAT 5 cable Before connecting the transmitter and receiver system you can acquire the EDID from the display or set the system to the default EDID see Section 9 TP 121 3 5EDID PT 110EDID Your TP 125EDID To connect the TP 125EDID and the TP 126 as the example in Figure 7 illustrates do the followi
24. re 2 Connecting the TP 121EDID XGA Audio Line Transmitter TP 121 3 5EDID PT 110EDID Your TP 121EDID 4 3 Technical Specifications TP 121EDID INPUTS Video 1 VGA UXGA on a 15 pin HD connector Audio 1 audio ANALOG 3 5mm mini jack OUTPUT 1 RJ 45 OUT connector BANDWIDTH 3dB Audio 20Hz to 20kHz 0 5dB RESOLUTION Up to WUXGA and 1080p S N RATIO Video 58dB unweighted 68 3dB 5MHz weighted Audio lt 80dB 0 to 40 C 32 to 104 F TEMPERATURE 40 to 70 C 40 to 158 F HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 12 1cm x 7 18cm x 2 42cm 4 76 x 2 83 x 0 95 W D H All measurements are based on the transmitter receiver pair Specifications are subject to change without notice at http www kramerelectronics com TP 121 3 5EDID PT 110EDID Your TP 121EDID 5 1 Your TP 123EDID This section describes the TP 123EDID XGA Audio Data Line Transmitter Overview The TP 123EDID is a high performance XGA stereo audio line transmitter It inputs an XGA signal up to WUXGA 1080p unbalanced stereo audio signal and unidirectional RxD RS 232 control commands and transmits them over CAT 5 cable to a receiver for example the Kramer TP 124 XGA Audio Data Line Receiver It converts the unbalanced stereo audio signal to a digital audio S PDIF stream before transmitting to preserve the quality of the audio signal When the TP 123EDID is connected to a display device and the EDI
25. signal level and or cable compensation equalization level if required Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level f necessary set the H SYNC and V SYNC switches on the underside By default both switches are set down for negative V SYNC and H SYNC polarity TP 121 3 5EDID PT 110EDID Your TP 125EDID Computer Graphics Audio RS 232 Control TP 125EDID AV Display System with Built in Speakers Figure 7 Connecting the TP 125EDID XGA Audio Data Line Transmitter 6 3 Connecting the RS 232 Port To control an RS 232 controllable remote device from a PC or RS 232 controller prepare an RS 232 cable with a 9 pin D sub connector at one end and a 3 pin terminal block connector at the other end as shown in Figure 8 TP 121 3 5EDID PT 110EDID Your TP 125EDID 19 RS 232 Pinout PIN 5 Connected to GND PIN 3 Connected to RxD PIN 2 Connected to TxD Connect this PIN To this PIN on the on the Terminal 9 pin D sub Block Connector Connector TxD PIN 2 RxD PIN 3 GND PIN 5 To PC 9 pin D sub Figure 8 RS 232 PINOUT Connection 6 4 Technical Specifications TP 125EDID INPUTS Video 1 UXGA on an 15 pin HD connector Audio 1 audio ANALOG 3 5mm mini jack OUTPUT 1 RJ 45 OUT connector RESOLUTION Up to WUXGA and 1080p S N RATIO Video 58dB unweighted 68 3dB 5MHz weighted Audio lt 80dB 40 to 70 C 40 to 158 F 10 to 90 RHL non con
26. splay or it can acquire the default EDID To acquire the display EDID do the following 1 Using a short cable connect the XGA INPUT 15 pin HD connector of the transmitter to the XGA input connector of the display Pins 12 and 15 of the VGA connector carry the EDID signal The cable used for capturing the EDID must pass all 15 pins 2 Connect the display power 3 On the transmitter connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity 4 Press the EDID CAPTURE button 5 Once the EDID STATUS flashes slowly several times the EDID is captured 6 Disconnect the display To acquire the default EDID Do not connect the transmitter to the display when acquiring the default EDID 1 On the transmitter connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity 2 Press the EDID CAPTURE button 3 Once the EDID STATUS flashes rapidly several times the default EDID is captured Alternatively you can press the EDID CAPTURE button after connecting the transmitter receiver system When the EDID STATUS LED flashes rapidly several times the default EDID information is acquired 26 TP 121 3 5EDID PT 110EDID Acquiring the EDID LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in
27. tton ln to capture the EDID information from the display 2 STATUS LED llluminates during normal operation flashes when acquiring the EDID 3 ON LED llluminates when receiving power 4 XGA IN 15 pin HD F connector Connects to the XGA source LINE OUT RJ 45 connector Connects to the LINE IN RJ 45 connector on a receiver Using a CAT 5 cable with RJ 45 connectors at both ends the PINOUT is defined in Section 8 e AUDIO IN 3 5mm mini jack Connects to the audio source 12V DC 12V DC connector for powering the unit 4 2 Connecting the TP 121EDID XGA Audio Line Transmitter You can use the TP 121EDID together with the TP 122N to configure a twisted pair transmitter and receiver system to transmit the video and audio signals via CAT 5 cable Before connecting the transmitter and receiver system you can acquire the EDID from the display or set the system to the default EDID see Section 9 TP 121 3 SEDID PT 110EDID Your TP 121EDID To connect the TP 121EDID with the TP 122N as the example in Figure 2 illustrates do the following 1 On the TP 121EDID connect the XGA source for example a laptop s graphics card to the XGA IN 15 pin HD F connector Audio source for example the audio out of the PC to the AUDIO IN 3 5mm mini jack You can use a Kramer C GMA GMA cable VGA 15 pin HD M audio jack to VGA 15 pin HD M audio jack to make both connections on one cable Cables are not supplied The
28. ur questions comments and feedback Web site www kramerelectronics com KRAMER E mail info kramerel com SAFETY WARNING Disconnect the unit from the power supply before opening and servicing PN 2900 000585 Rev 6
29. urce Figure 10 Connecting the PT 110EDID XGA Line Transmitter TP 121 3 5EDID PT 110EDID Your PT 110EDID Ea 7 3 Technical Specifications PT 110EDID INPUT 1 VGA UXGA on a 15 pin HD connector OUTPUT 1 RJ 45 LINE OUTPUT connector S N RATIO 69dB worst case COUPLING AC POWER CONSUMPTION 12V DC 320mA OPERATING TEMPERATURE 0 to 40 C 32 to 104 F STORAGE TEMPERATURE 40 to 70 C 40 to 158 F HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 6cm x 6 5cm x 2 5cm 2 36 x 2 56 x 1 W D H WEIGHT 0 14kg 0 31lbs approx ACCESSORIES Power supply OPTIONS RK 4PT 19 rack adapters All measurements are based on the transmitter receiver pair tested with 100m CAT 5 cable Specifications are subject to change without notice at http www kramerelectronics com 24 TP 121 3 SEDID PT 110EDID Your PT 110EDID Pas 8 Wiring the TP LINE IN LINE OUT RJ 45 Connectors This section defines the TP pinout using a straight pin to pin cable with RJ 45 connectors Note that the cable Ground shielding must be connected soldered to the connector shield EIA TIA 568B Figure 11 TP PINOUT In PIN Wire Color 1 Orange White 3 4 Bue Green 7 Brown White rs eom s 4 6 7 TP 121 3 5EDID PT 110EDID Wiring the TP LINE IN LINE OUT RJ 45 Connectors Ea 9 Acquiring the EDID The transmitter can acquire the EDID information from the connected di
Download Pdf Manuals
Related Search