Panasonic WV-Q122A
Contents
1. the screws supplied with the bracket and a hexagonal wrench for M6 Recommended tightening torque for common use in M5 and M6 2 45 N m 1 81 lbf ft Secure the plate with the 4 screws removed in Step 4 on the rear side of the bracket and seal the slit of the cable Cap Recommended tightening torque 0 78 N m 0 58 ptn Cable Sealant locally procured Cable cap with a slit Inside Step 6 Connect the cables to the camera Connect the cables from the housing base with the cables coming through the wall After cable connection seal the connecting portion with waterproof tape locally procured IMPORTANT e These operations shall be performed in accordance with the electric installation engineering standards Perform sealing to prevent the connecting portion of the cables from being exposed Moisture may come into the camera from the gap among the cables and cause the inside of the dome cover to become foggy Step 7 Mount this bracket on the wall with 4 screws M8 locally orocured Minimum pull out strength 823 N 185 lbf per 1 pc Go to 3 Mounting of the camera body on the mount bracket ies 12 page 11 12 3 Mounting of the camera body on the mount bracket Step 1 For the case of color CCTV camera peel off the seal on the top of the camera and specify the communication method and unit address using the DIP switches Ref2. Panasonic Operating Instructions Wall Mount Bracket Model No WV Q1 OA Panasonic The camera in the illustration is separately sold Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual CONTENTS AE EE E 3 ge e 3 Precautions for installation EE 4 Major operino CNEL EE 5 Installations COnnectionS eensuecsciccnnnesnnsvdsenwansisaanaunonsuntwadiniesenbwiaweneudvennoandeessanslmnedsnnsstbaweaaunsvesinosameunduaiodeccutusuasinnsaundunhanedunsniearendswnia 6 PEIE ONO E 14 Standard ACCSSSOMESS ive isnsecaissincessnicaaneannerseaiedaberentsinnbasensdosnedsnneauldsiooneswnsinnsasdiesiiniedsonnsebiedeassnehessabesnmrsendedantedulsednissiuheieaneeniontdvs 14 This mount bracket is used for installing the color CCTV camera and network camera on a wall Refer to the catalog or operating instructions of the camera for further information about the compatible models Precautions Refer installation work to the dealer Installation work requires technique and experiences Failure to observe this may cause fire electric shock injury or damage to the product Be sure to consult the dealer Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced Otherwise the mounting portions will deteriorate and acci dents such as
3. a fall of this product may occur The screws and bolts must be tightened to the speci fied torque Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents Do not use this bracket except with suitable cameras Failure to observe this may cause a drop resulting in injury Select an installation area that can support the total weight Selecting an inappropriate installation surface may cause this product to fall down or topple over resulting in injury or accidents Installation work shall be started after sufficient reinforce ment Do not rub the edges of metal parts with your hand Strong rubbing may cause injury Periodic inspections shall be conducted Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents Consult the dealer for the inspections The measures of protection against a fall of this prod uct shall be taken Failure to observe this may cause a drop resulting in injury or accidents Be sure to install the safety wire Do not install this product in locations subject to vibration Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents Do not strike or give a strong shock to this product Failure to observe this may cause fire or injury Install this product in a location high enough to avoid people and objects from bumping the product Failure to observe this may cau
4. ay become foggy Matters you should know at installation work Compatibility of devices are restricted Before connections check the ratings and dimensions of the devices to be used Refer to Panasonic CCTV System General Catalog or con tact your dealer for further information Major operating controls Hexagonal screw hole for mounting camera 4 points Camera mounting part Wire hook section Cable access hole front 220 mm 8 21 32 inches Cable access hole rear Installations Connections Be sure to read Precautions and Precautions for installation before installation Read the operating instructions for the camera to be installed as well The Operating Instructions mainly describe for installing a network camera The basic flow of the installation operation is the same as the one for the color CCTV camera The flow of how to install the wall mount bracket is described as follows 1 How to detach the housing base 6 page Remove the housing base and attachment pipe from the camera body 2 Attaching the mount bracket 8 page E When laying cables through the cable access hole front es 8 page E When laying cables after drilling a hole through the wall fe 10 page 3 Mounting of the camera body on the mount bracket Ir 12 page Secure the camera body to the housing base 1 How to detach the housing base Before attaching the camera to the wall mount bracket detach
5. ch for M5 For the case of the camera with M6 screws being used Use the screws supplied with the bracket and a hexagonal wrench for M6 Recommended tightening torque for common use in M5 and M6 2 45 N m 1 81 lbf ft Step 4 Seal the slit of the cable cap for the prevention of water leakage Cable Sealant locally procured Cable cap with a slit Step 5 Mount another cable cap accessory on the rear plate LC Step 6 Mount the mount bracket on the wall with 4 screws M8 locally procured Minimum pull out strength 823 N 185 lbf per 1 pc EN EE Step 7 Connect the cables to the camera Connect the cables from the housing base with the cables on the wall After cable connection seal the connecting portion with waterproof tape locally procured IMPORTANT e These operations shall be performed in accordance with the electric installation engineering standards Perform sealing to prevent the connecting portion of the cables from being exposed Moisture may come into the camera from the gap among the cables and cause the inside of the dome cover to become foggy Go to 3 Mounting of the camera body on the mount bracket ies 12 page 10 E When laying cables after drilling a hole through the wall Step 1 Step 2 Decide the mounting position and drill a hole for a screw or Mount the cable cap accessory on the cable access hole an a
6. er to the Operating Instructions of the color CCTV cam era for how to set the DIP switch Put the seal back after specifying them Communication method specifying with SW2 Unit address specifying with SW1 Camera top DIP switch Step 2 Align the flat spring with the START position If not rotate the plate on the top of the camera clockwise to align it with the START position For the case of network camera Flat spring Projections For the case of color CCTV camera Flat spring Projections CS Plate SS my We Step 3 Engage the safety wire with the wire hook section Safety wire Step 4 When attaching the camera to the housing base the posi tioning pin shall be on the REAR side Make sure that the camera is securely attached to the mount bracket by turning the bracket counterclockwise seen from below Tighten them firmly with the 3 screws that have been removed in Step 1 Special screw fixing screw These screws are hexagon screws Use a hexagon wrench There are 2 types of wrenches to be used one is hexago nal wrench for M5 WV SW598 and the other is hexago nal wrench for M6 Refer to the Operating Instructions of the camera for the wrench to be used which depends on models Recommended tightening torque for common use in M5 and M6 2 45 N m 1 81 lbf ft Fixing screws 3 pcs Positioning __ _ 2 pin Camera Protection cover The illustrati
7. he power cable is not connected to the main power supply Installation area for this product Consult the dealer about the installation area to select a strong wall area e Screws used for installing this product on a wall are not supplied Prepare them according to the material and strength of the area where the product is to be installed Recommended screw M8 x 4 pcs Minimum pull out strength per 1 pc 823 N 185 Ion e Do not mount the product on a plaster board or a wooden section because they are too weak If the prod uct IS unavoidably mounted on such a section the sec tion shall be sufficiently reinforced Mounting method for this product This product is designed to be used as a pendant mount camera If the product is mounted on a desktop or at a slant it may not work correctly and Its lifetime may be short ened Protection from lightning When cables are used outdoors there is a chance that they may be affected by lightning In this case install a lightning arrester just before where the cables connect to the cam era Do not place this product in the following places e Locations where a chemical agent is used such as a swimming pool e Locations subject to moisture or ol smoke such as a kitchen e Locations that have a specific environment that is sub ject to an inflammable atmosphere or solvents e Locations where radiation x ray intense radio wave or strong magnetism is produced e Locations where corros
8. ive gas is produced locations where it may be damaged by briny air such as sea shores e Locations where the temperature is not within the speci fied range 50 C to 55 C 58 F to 131 F e Locations subject to vibrations such as on vehicles marine vessels or above product lines This product is not designed for onvehicle use e Locations subject to condensation as the result of severe changes in temperature In case of installing the product in such locations the dome cover may become foggy or condensation may be caused on the cover Screw tightening e The screws and bolts must be tightened with an appro priate tightening torque according to the material and strength of the installation area Do not use an impact driver Use of an impact driver may damage the screws or cause tightening exces sively e When a screw is tightened make the screw at a right angle to the surface After tightening the screws or bolts perform checks to ensure that the tightening is sufficient enough so that there is no movement or loose ness The protection cover attached to the camera unit shall be removed after completion of the installation rain wash coating model Make sure to remove this product if it will no longer be used Take notice of humidity Install this product when the humidity is low If this product is installed during rainfall or at a high humidity the inside may be exposed to moisture and the dome cover m
9. nchor and a hole for cable installation in the wall front Procure 4 pieces of M8 screws and anchors to secure the this bracket on the wall All screws and anchors shall be stainless steel The hole diameter shall be decided in accordance with the screws and anchors to be used A hole on the wall with a diameter of 30 mm 1 3 16 inches or less for a screw or an anchor can be hidden with this bracket Step 3 Make a slit in the center of another cable cap accessory with a cutter 80 mm 3 5 32 inches 120 mm OU oO Bes O E St NS a wz w Step 4 Remove the 4 screws from the rear side of the bracket remove the plate and mount the cable cap that was slit in Step 3 7 3 32 inches Hole for cable installation 2388 mm 91 1 2 inches Step 5 Lay the cables from the housing base via this blacket into the slit cable cap Secure the housing base to the wall mount bracket Attach the housing base to the mount bracket using the 4 screws The REAR mark of the housing base shall be directed to the wire hook section Refer to the Operating Instructions of the camera for the screws and the wrenches to be used which depends on models For the case of the camera with M5 screws being used WV SW598 Use the screws supplied with the camera and a hexagonal wrench for M5 For the case of the camera with M6 screws being used Use
10. o the applicable description E When laying cables through the cable access hole front rs 8 page E When laying cables after drilling a hole through the wall es 10 page E When laying cables through the cable access hole front Step 1 Decide the mounting position and drill a hole in the wall Procure 4 pieces of M8 screws and anchors to secure the this bracket on the wall All screws and anchors shall be stainless steel The hole diameter shall be decided in accordance with the screws and anchors to be used A hole on the wall with a diameter of 30 mm o1 3 16 inches or less can be hidden with this bracket 80 mm Bess 180 mm 7 3 32 inches Step 2 Make a slit in the center of the cable cap accessory with a cutter Step 3 Pass the cables from the housing base through this bracket and mount the cable cap that was slit in Step 2 on the cable access hole front Secure the housing base to the wall mount bracket Attach the housing base to this bracket using the 4 screws supplied with the camera The REAR mark of the housing base shall be directed to the wire hook section Wire hook section Cable access hole front Refer to the Operating Instructions of the camera for the screws and the wrenches to be used which depends on models For the case of the camera with M5 screws being used WV SW598 Use the screws supplied with the camera and a hexagonal wren
11. on above is provided for describing the top of the camera and therefore this bracket is omitted Step 5 Mount the front and rear sunshields and then remove the orotection cover Refer to the Operating Instructions of the camera for further information Removal of the protection cover is described only for rain wash coating model Housing base Front rear sunshields Supplied with the camera 13 14 Specifications Ambient operating temperature 50 C to 55 C 58 F to 131 F Dimensions 120 mm W x 220 mm H x 269 mm D 4 23 32 inches W x 8 21 82 inches H x 10 19 32 inches D Mass Approx 2 kg 4 42 lbs Finish Aluminum die cast coating color fine silver 901 Weight and dimensions indicated are approximate Specifications are subject to change without notice Standard accessories Operating Instructions this document 1 set The following are for installation I EE 2 PCS Camera mounting screw Hexagon Screw Me A pcs For U S and Canada Panasonic System Communications Company of North America Unit of Panasonic Corporation of North America www panasonic com business For customer support call 1 800 528 6747 Three Panasonic Way Secaucus New Jersey 07094 U S A Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Canada 905 624 5010 www panasonic ca Panasonic System Networks Co Ltd 2013 For Europe and other countries Panasonic Co
12. rporation http panasonic net Importer e name and address to follow EU rules Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg Germany Ns0913 0 PGQX1409ZA Printed in China
13. se injury Do not hang down from this product or use this prod uct as a pedestal Failure to observe this may cause a drop resulting in acci dents Do not install the product in a windy place Installation of the product in wind with a speed of 40 m s or more may cause a drop resulting in accidents The measures of protection against snowfall shall be taken Weight of snow may cause a fall of the product resulting in injury or accidents Protect the product against snowfall by installing under eaves Precautions for installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation The installation should comply with local electrical code Before start the installation connection check and prepare the required devices and cables Before starting the con nection turn the power of the devices including the camera and the PC off Refer installation work to the dealer Failure to observe this may cause fire electric shock injury or damage to the product Power supply Use a power supply device equipped with the ON OFF switch for servicing When the power cord of the product is connected to the power supply device the power will be supplied to the product When the product is supplied the product will perform panning tilting Zooming and focusing Before cleaning the product make sure that t
14. the housing base and attachment pipe from the camera so that installation and connections can be performed Step 1 Remove the fixing screws 3 pcs that are securing the housing base and the camera The removed screws will be required when attaching the camera to the housing base Use caution not to lose these Screws Special screw fixing screw These screws are hexagon screws Use an M5 hexagon wrench There are 2 types of wrenches to be used one is hexago nal wrench for M5 WV SW598 and the other is hexago nal wrench for M6 Protection cover Refer to the Operating Instructions of the camera for the wrench to be used which depends on models Fixing screws 3 pcs IMPORTANT e The protection cover attached to the camera unit shall be removed after completion of the installation Only for rain wash coating model Step 2 To separate the housing base from the camera turn the housing base to the direction of the arrow as illustrated Refer to the illustration in Step 1 Housing base Camera Protection cover Step 3 Remove the attachment pipe from the upper base by loos ening 4 screws Attachment pipe Go to E When laying cables through the cable access hole front 8 page or RW When laying cables after drilling a hole through the wall es 10 page 2 Attaching the mount bracket The installation of the wall mount bracket is roughly divided into 2 methods Refer t
Download Pdf Manuals
Related Search