Jarden HASF2120 fan
Contents
1. HASF2120 11EM1 qxd HASF212009EM1 qxd 7 14 11 2 20 PM Page 1 FAN CLEANING FAN STORAGE e Always ane the fan before cleaning or Your fan can be stored in the off season either partially disassembling disassembled or assembled It is important to keep it in Do not allow water to drip on or into the fan motor a safe dry location housing e If stored disassembled we recommend using the e Be sure to use a soft cloth moistened with mild soap solution e Do not use any of the following as a cleaner gasoline thinner benzene original or appropriately sized box e f stored assembled or partially assembled remember to protect the fan head from dust Fan Blade Cleaning l STEP 1 To access the fan blade remove the front grill If you have any questions regarding your product and the fan blade cap or would like to learn more about other Holmes products please contact our Consumer Service Department at 1 800 546 5637 or visit our website at www holmesproducts com STEP 2 Clean the fan blade front and rear grills with a soft moist cloth STEP 3 Replace blade tighten blade cap and securely fasten the front grill Fan Head Base and Pole Cleaning Using a soft moist cloth with or without a mild soap solution carefully clean the fan base pole and head Please use caution around the motor housing area Do not allow the motor or other electrical components to be exposed to water 2011 Sunbeam Products Inc doing2. edge of a table counter or come in contact with hot surfaces or leave exposed to high traffic areas Do not use outdoors 14 To disconnect grip plug and pull from wall outlet Never yank on cord 15 Always use on a dry level surface 16 Do not operate fan until fully assembled with all parts properly in place 17 This product is intended for household use ONLY and not for commercial or industrial applications 18 WARNING To reduce the risk of electrical shock and injury to persons do not use in window 19 WARNING To reduce the risk of fire or electric shock do not use this fan with any solid state speed control device 20 This product employs overload protection fuse A own fuse indicates an overload or short circuit situation If the fuse blows unplug the product from the outlet Replace the fuse as per the user servicing instructions follow product marking for papi use ating and check the product If the replacement fuse blows a short circuit may be present and the product should be discarded or returned to an authorized service facility for examination and or repair PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS Figure electrician to install t outlet reverse the P THIS APPLIANCE HAS A POLARIZED PLUG one blade is wider than the other To reduce the risk of electric shock this plug is intended to fit in a polarized outlet only one way If the plug does not fit fully in t
3. basic safety precautions should always be taken including the following 1 2 3 a _ l Read all instructions before using this appliance Use fan only for purposes daikon in the instruction manual To protect against electrical shock do not immerse unit plug or cord in water or spray with liquids an plug the appliance directly into a 120V AC electrical outlet Close supervision is necessary when any appliance is used by or near children Unplug from outlet when not in use when moving an from one location to another before putting on or taking off parts and before cleaning Avoid contact with moving parts Do not operate in the presence of explosive and or ammapie fumes S To avoid fire hazard NEVER place the cord under w or any parts near an open flame cooking or other heating appliance Do not operate any appliance with a damaged cord or plug after the appliance malfunctions or has been dropped damaged in any manner Discard fan or return to an authorized service facility for examination and or repair Do not run cord under a Do not cover cord ila with throw rugs runner or similar coverings Do not route cord under furniture or appliances Arrange cord away from traffic area and where it will not be tripped over The use of attachments not recommended or sold by the appliance manufacturer may cause hazards Do not let the cord hang over the
4. business as Jarden Consumer Solutions All Rights Reserved Distributed by Sunbeam Products Inc doing business as Jarden Consumer Solutions Boca Raton Florida 33431 153626 9100010012524 HASF2120_11EMI GCDS HOL22426 PH Printed In China AD ar 3 YEAR LIMITED WARRANTY Sunbeam Products Inc doing business as Jarden Consumer Solutions or if in Canada Sunbeam Corporation Canada Limited doing business as Jarden Consumer Solutions collectively JCS warrants that for a period of three years from the date of purchase this product will be free from defects in material and workmanship JCS at its option will repair or replace this product or any component of the product found to be defective during the warranty period Replacement will be made with a new or remanufactured product or component If the product is no longer available replacement may be made with a similar product of equal or greater ahe This is your exclusive warranty Do NOT attempt to repair or adjust any electrical or mechanical functions on this product Doing so will void this warranty This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable Keep the original sales receipt Proof of purchase is required to obtain warranty performance JCS dealers service centers or retail stores selling JCS products do not have the right to alter modify or any way change the terms and conditions of this warrant
5. he ug If it still does not fit contact a qualified e proper outlet DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY AD ar ASSEMBLY INSTRUCTIONS Base Assembly See Figure 1 You will need the base and four extension legs Push in the small tab located on the bottom of each extension leg and snap into base Pole Assembly See Figure 2 STEP 1 Remove the height adjustment collar from the pole by turning counter clockwise STEP 2 Take the pole assembly with the solid end down and insert it into the base The hollow end of the pole will be facing up STEP 3 Replace the height adjustment collar over the pole assembly slide it down the pole and secure by turning clockwise Refer to Figure 2 Figure 3 BS L m SA D H K Logo Plate Front Grill Fan Blade Cap Fan Blade Rear Grill Mounting STS ZX SONA ARNA V o A N Q weg B li NEA PAON g wed Sf yy IS LTO SS NNS AS ii om GG Z Neck Tilt Adjustment Knob Upper Pole Speed Control Knob Oscillation Knob Motor Housing Hogi Adjustment Collar Lower Pole Extension Legs Fan Post Screw Fan Head Assembly See Figure 4 6 STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 Figure 4 Figure 5 LA ar Position the rear grill over the motor shaft making certain t
6. he 2 notches at the top and bottom of the rear grill fit over the 2 prongs on the motor housing Please make sure the rear grill fits securely against the motor housing Refer to Figure 4 Secure the rear grill in its place using the rear grill mounting ring Turn this ring clockwise and tighten firmly Refer to Figure 5 Slide the fan blade with the hollowed interior of the blade facing towards the rear grill firmly onto the motor shaft Make sure the shaft protrudes from the front of the blade Refer to Figure 6 Secure the fan blade onto the motor shaft by turning the fan blade cap in a counter lockwise direction until it is firmly in place Refer to Figure 6 Prepare the koni grill by simply snapping the ogo plate in place Center the front grill by aligning the Holmes logo so it is acai af parallel to the floor Then secure the front and rear grills completely together by snapping into place Lastly tighten the securing screw at the bottom of the rear grill aN WX AKA WSO YEN X ae MANN uai E I KZA UTS Final Assembly First place fan head assembly onto the upper pole ining up the fan post screw with the hole in the extension pole Slide head assembly our upper pole and secure by tightening fan post screw Lastly insert the tilt adjustment knob into the neck joint and tighten in place NOTE If your fan does not have a screw hole in the extension pole but instead has an indentation around the top
7. of the pole please do the following STEP 1 First place the fan head assembly onto the upper pole and tighten the fan post screw until a secure fit is obtained STEP 2 Insert the tilt adjustment knob into the neck joint and tighten in place OPERATING INSTRUCTIONS Set fan base on a dry level surface 2 Please make sure the Speed Control Knob is in the off position The Speed Control Knob is located on the top of the Fan Motor Housing 3 Plug cord into any standard 120 volt AC outlet 4 The SPEED is adjusted by turning the control knob to the desired setting OFF HI MED LO speed 5 The OSCILLATION Knob is located on the top of the Fan Motor Housing To Start Oscillation push Oscillation Knob down To Stop Oscillation pull Oscillation Knob up ADJUSTMENT INSTRUCTIONS Tilt Adjustment Follow these instructions to tilt the Fan Head for upward angle air movement STEP 1 To change the tilting angle of the fan head simply loosen the Tilt Adjustment Knob see Figure 3 STEP 2 Mave the fan head to the desired angle and firmly tighten the knob to lock in place Height Adjustment Follow these instructions to adjust the height of the fan STEP 1 Turn the Tin adjustment collar counter clockwise to loosen pole STEP 2 Adjust the extension pole to the desired ds and firmly tighten the height adjustment collar in a clockwise direction CLEANING MAINTENANCE INSTRUCTIONS Follow these instructions to cor
8. rectly and safely care for your stand fan Please remember REPLACEABLE FUSE If your 5 Amp 125 Volt replaceable fuse blows aie order a new fuse at 1 800 546 5637 Follow the elow instructions to replace the fuse on the plug User Servicing Instructions 1 Unplug your fan Grasp plug and remove from the arene or other outlet device Do not unplug by pulling on cord 2 Open hiss cover located on the top of the plug b using your thumb or a flathead screwdriver to slide the cover down towards the prongs Note Ensure that fuse cover is completely open before attempting to remove fuse 3 Remove fuse carefully by using a small screwdriver to pry the fuse out of the compartment by the metal lt ends of the fuse see Figure 4 Place plug on a solid flat surface Insert new 5 Amp 125 Volt fuse into fuse compartment and use a small screwdriver to secure the metal ends of the fuse into the compartment Caution Risk of fire Replace fuse only with 5 Amp 125 Volt fuse 5 Slide fuse cover closed completely If fuse cover is difficult to close make sure fuse is secured in place completely by pressing down on metal ends of the use 6 Risk of fire Do not replace attachment plug Contains a safety device fuse that should not be removed Discard product if the attachment plug is damaged
9. y This warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of the product use on improper voltage or current use contrary to the operating instructions disassembly repair or alteration by anyone cat than JCS or an authorized JCS service center Further the warranty does not cover Acts of God such as fire flood hurricanes and tornadoes What are the limits on JCS s Liability JCS shall not be liable for any incidental or consequential damages caused by the breach of any express implied or statutory warranty or condition Except to the extent prohibited by applicable law any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty JCS disclaims all other warranties conditions or representations express implied statutory or otherwise JCS shall not be liable for any damages of any kind resulting from the purchase use or misuse of or inability to use the product including incidental special consequential or similar damages or loss of profits or for any breach of contract fundamental or otherwise or for any fain brought against purchaser by any other party Some provinces states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusion may not apply to
10. you This warranty gives you specific legal rights and you may also have other rights that vary from province to province state to state or jurisdiction to jurisdiction How to Obtain Warranty Service In the U S A If you have any questions regarding this warranty or would like to obtain warranty service please call 1 800 546 5637 and a convenient service center address will be provided to you In Canada If you have any questions regarding this warranty or would like to obtain warranty service please call 1 800 546 5637 and a convenient service center address will be provided to you In the U S A this warranty is offered by Sunbeam Products Inc doing business as Jarden Consumer Solutions located in Boca Raton Florida 33431 In Canada this warranty is offered by Sunbeam Corporation Canada Limited doing business as Jarden Consumer Solutions located at 20 B Hereford Street Brampton Ontario L6Y OMI If you have any other problem or claim in connection with this product please write our Consumer Service Department PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE ais Ly Owner s Guide HASF2120 Holmes VK 20 inch 50cm Power Stand Fan PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS HASF2120 11EM1 qxd HASF212009EM1 qxd 7 14 11 2 20 PM Page 2 PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances
Download Pdf Manuals
Related Search