Snow Joe Shredder Joe SDJ616
Contents
1. ay A Division of Snow Joe LLC IMPORTANT Safety Instructions All Operators Must Read These Instructions Before Use General Power Tool Safety Warnings Z CAUTION Before using this electric tool carefully read and observe the safety rules and instructions listed below Before starting work make sure that you know how to stop the machine in case of an emergency The incorrect use of this machine could cause serious injury Keep these instructions in a safe place and on hand so that they can be consulted when required N WARNING Read all safety warnings and all instructions Failure to follow all warnings and instructions may result in electric shock fire or serious injury N WARNING When using electric gardening appliances basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following N WARNING This electric leaf mulcher shredder is designed to shred leaves thatch grass clippings and pine needles It cannot be used to shred branches sticks or brush For All Double Insulated Appliances 1 Replacement parts When servicing use only identical replacement parts 2 Polarized appliance connections To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other and will require the use of a polarized extension cord The appliance plug will fit into a polarized extension cord only2. Inspect extension cords periodically and immediately replace them if they are damaged Only use an authorized service facility to repair the appliance Keep the handles of the unit dry clean and free from oil and grease 17 Check for damaged parts Before using the appliance carefully check the device to confirm that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other condition that may affect its operation Any part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual Extension Cords e Make sure your extension cord is intact and in proper working order When using an extension cord be sure to use one heavy enough to carry the current your product will draw An undersized cord will cause a drop in line voltage resulting in loss of power and overheating Table 1 shows the correct size to use depending on cord length and nameplate ampere rating If in doubt use the next heavier gauge The smaller the gauge number is the heavier the cord e Ground Fault Circuit Interrupter GFCl protection should be provided on the circuit s or outlet s to be used for this electric appliance Receptacles are available with built in GFCI protection and may be used for this measure of safety Use only UL listed extension cords Inspect the extension cord bef
3. one way If the plug does not fit fully into the extension cord reverse the plug If the plug still does not fit obtain a correct polarized extension cord A polarized extension cord will require the use of a polarized wall outlet This plug will fit into the polarized wall outlet only one way If the plug does not fit fully into the wall outlet reverse the plug If the plug still does not fit contact a qualified electrician to install the proper wall 2013 by Snow Joe LLC All rights reserved Original instructions Form No SJ SDJ616 880E OPERATOR S MANUAL outlet Do not change the equipment plug extension cord receptacle or extension cord plug in any way For All Appliances 1 Avoid dangerous environments Do not use electrical appliances in damp or wet locations 2 Do not use in the rain 3 Keep children and pets away All bystanders including children and pets should be kept a safe distance away from the work area 4 Dress properly Do not wear loose clothing or jewelry They can be caught in moving parts Use of rubber gloves and substantial footwear is recommended when working outdoors Wear protective hair covering to contain long hair 5 Use safety glasses Always wear protective eyewear and use a face or dust mask when operating an appliance that generates a significant amount of dust 6 Use the right appliance Do not use the appliance for any job except that for which it is intended 7
4. Open the box Fig 1 Assembling the Mulcher Stand 1 Loosen the height adjustment knob on the leg and pull the tube to the desired height tighten the knob to secure the leg in place Figs 4 amp 5 Fig 4 Fig 2 Fig 5 ics 0 _ 2 With your finger pressed against the leg pin indicated in Fig 6 insert the leg into the hole on the motor housing assembly Let the pin slip into the hole to secure the leg in place Repeat with the two other legs until the two remaining holes on the housing assembly are properly fitted 3 Remove the motor bracket from the funnel Cover plate Motor bracket Funnel UU Fig 3 Fig 6 Assembling the Mulching Power Head 1 Make sure the motor housing sits securely on the three legs Fig 7 3 Fit the funnel cover in the funnel Use the 8 locking tabs on the funnel to ensure a secure fit Fig 9 Fig 7 2 Fit the funnel onto the motor housing aligning the funnel gap with the motor housing rib Use the clamps located on the motor housing to secure the funnel in place Fig 8 Fig 9 Funnel cover Locking tabs Funnel Fitting the Collection Bag NOTE This unit does not come with a leaf collection ba
5. ZAWARNING To reduce the risk of electric shock use only with an extension cord intended for outdoor use such as an extension cord of cord type SW A SOW A STW A STOW A SUW A SUOW A SUTW A or SUTOW A 8 Avoid unintentional starting Do not carry a plugged in appliance with your finger on the switch Make sure the switch is off before plugging in the appliance 9 Do not abuse the cord Never carry the appliance by its cord or yank the cord to disconnect it from the receptacle Keep the cord away from heat oil and sharp edges 10 Do not grasp the exposed cutting blades or cutting edges when picking up or holding the appliance This precaution only applies for grass shears and similar appliances 11 Do not force the appliance It will do the job better and with less likelihood of a risk of injury if it is used at the rate for which it was designed 12 Do not overreach Keep proper footing and balance at all times 13 Stay alert Watch what you are doing Use common sense Do not operate the appliance when you are tired 14 Disconnect the appliance Disconnect the appliance from the power supply when it is not in use before servicing it and when changing accessories SAVE THESE INSTRUCTIONS For household use only 15 Store idle appliances indoors When not in use appliances should be stored indoors in a dry and high or locked up place out of the reach of children 16 Maintain appliance with care
6. arge during the first 90 days After the initial 90 days batteries will be replaced at a prorated cost to the customer e Idlers cables and electrical components are warranted to the original purchaser for use at household or residence for a period of two years Exclusions e Snow Joe brand engines are covered under this warranty All other engines and engine accessories are covered only by the engine manufacturer s warranty and are not covered by this warranty e Parts used that are not genuine Snow Joe parts are not covered by this warranty e Damages resulting from misuse alteration improper assembly improper adjustment neglect or accident which requires repair is not covered under this warranty e Belts augers and tines are not covered under warranty belts augers and tines wear out and can be purchased at www snowjoe com or by calling 1 866 766 9563 Snow Joe LLC may from time to time change the design of its products Nothing contained in this warranty shall be construed as obligating Snow Joe LLC to incorporate such design changes into previously manufactured products nor shall such changes be construed as an admission that previous designs were defective This warranty is intended to cover product defects only Snow Joe LLC is not liable for indirect incidental or consequential damages in connection with the use of the Snow Joe Products covered by this warranty This warranty does not cover any cost or
7. duce the risk of electrical shock use only an extension cord intended for outdoor use If for any reason you need to inspect clean or repair the leaf mulcher shredder turn the unit off and wait until it comes to a complete stop Then disconnect the power cord before conducting such inspection or repair Disconnect the leaf mulcher shredder from the power source when it is not in use before servicing and when replacing the cutting lines When feeding material into the leaf mulcher shredder make sure that you do not accidentally insert pieces of metal rocks bottles cans or other foreign objects Do not force the leaf mulcher shredder It will do the job better and with less likelihood of injury if it is used at the rate for which it was designed If the cutting mechanism strikes a foreign object or if you notice an unusual rattling noise or vibration coming from the leaf mulcher shredder immediately switch off the unit and wait until it comes to a complete stop Then disconnect the power cord and follow the steps below a Remove any foreign or clogged material b Check for any loose parts and tighten them to ensure continued safe operation c Replace or repair any damaged parts Check the discharge area periodically after stopping the leaf mulcher shredder to ensure that the processed material does not build up and clog the motor cooling vents Do not move the leaf mulcher shredder when the motor is running or wh
8. eaf mulcher shredder is double insulated eliminating the need for a separate grounding system Use only identical replacements parts Read the instructions before servicing double insulated leaf shredders Use this leaf mulcher shredder only as described in this manual N WARNING To reduce the risk of electric shock do not expose to rain Store indoors N WARNING For your own safety read and understand the operator s manual Do not run the unit unattended N CAUTION To reduce the risk of injury from moving parts unplug the unit before cleaning or servicing Additional Safety Rules for Leaf Mulcher Shredder 1 10 11 12 13 Become familiar with all sections of this owner s manual before attempting to operate the leaf mulcher shredder This leaf mulcher shredder should be used solely for the purpose for which it was intended Use only parts or accessories specifically designed for use with this leaf mulcher shredder Using other parts or accessories could increase risk of injury Keep your hands and other body parts and loose articles of clothing away from the funnel and upper housing area Avoid dangerous environments Do not use the leaf mulcher shredder in damp or wet locations Do not operate in rain Store indoors when not in use in a dry and high or locked up place out of the reach of children This leaf mulcher shredder should be operated on a solid level surface ZAAWARNING To re
9. en your finger is on the switch Unpacking Due to modern mass production techniques it is unlikely that your power tool is faulty or that a part is missing If your power tool does not arrive intact do not operate the tool until the parts have been replaced or the fault has been rectified Contact the Snow Joe customer service center for assistance Failure to do so could result in serious personal injury Safety Symbols The following table depicts and describes safety symbols that may appear on this product Read understand and follow all safety instructions before attempting to assemble and operate the leaf mulcher shredder Symbol Description SAFETY ALERT indicates a precaution a warning or a danger READ THE OPERATOR S MANUAL S Read understand and follow all safety instructions in the manual s before attempting to assemble and operate d B gt WARNING Keep away from rain and other wet areas G Risk of eye injury Use safety glasses or similar eye protection Wear hearing protection Wear protective gloves when using the machine and handling debris Wear protective shoes during operation H ji CAUTION Remove plug from the outlet immediately if the cord is damaged or cut CAUTION Remove plug from the outlet before conducting inspection cleaning or maintenance DANGER Keep hands and feet away from the cutting area Keep bystanders at a
10. expense incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non use of this product while waiting for completion of repairs under this warranty Some states do not allow exclusions of incidental or consequential damages so the above exclusions may not apply in all states This warranty may give you specific legal rights in your state If you wish to contact Snow Joe please direct inquiries to the Customer Service Department Snow Joe Center 86 Executive Avenue Edison NJ 08817 Customers who have purchased Snow Joe products exported from the United States and Canada should contact their Snow Joe Distributor Dealer to obtain information applicable for your country province or state If for any reason you are not satisfied with the distributor s service or if you have difficulty obtaining warranty information contact your Snow Joe seller If in the event your efforts are unsatisfactory please write to the Snow Joe Center at the above address If you have any questions about your product warranty please call 1 866 SNOW JOE or visit us online at www snowjoe com 12
11. g You must supply your own You may use a plastic paper or cloth collection bag depending on your preferred method of waste disposal 1 Open the bag and fit it around the motor housing using the elastic straps located at the base of the unit to secure the bag in place Fig 10 NOTE You can remove the mulcher stand and fit the hopper onto a leaf bag lined trash container for easy and convenient disposal of the shredded waste Fig 10 Operation Adjusting the Control Dial The control dial Fig 12 regulates the particle size and speed ON OFF Switch at which material passes through the unit When the control dial is set in the COARSE position material will process The On Off switch is located on the lower side of the motor through the unit faster but will yield a larger particle size housing portion of the power head To turn on push the green than if the dial were set to the FINE position The FINE button To turn off push the red button Fig 11 position setting will discharge the material slower but will yield the smallest particle reduction ratio up to 16 1 Use the special settings for pine needles grass clippings and thatch as needed For best results material should be shredded when dry WET LEAVES T DRY LEAVES TINE GRASS THATCH COARSE MEDIUM NOTE If the unit stops wait 1 minute and then press the circuit breaker reset button A CAUTION To prevent exp
12. oe service center AN CAUTION Cleaning the motor housing with water will lead to permanent motor damage Use a dry cloth only Replacing the Cutting Line This electric leaf mulcher shredder features a bladeless mulching system that utilizes 0 1 in x 12 6 in 0 25 cm x 32 cm heavy duty trimmer line Twenty replacement cutting lines are included in the box Visit www snowjoe com to purchase additional cutting line Model SDJ616L 1 Replace the cutting line when a noticeable decrease in shredding efficiency is observed To remove the worn cutting lines cut the old lines and pull the remaining line out of the spinner head 2 When installing new cutting lines feed each end of the new line through the two holes in the post on top of the spinner head Fig 13 4 Thread the lines through each corresponding ferrule Fig 15 Fig 13 Fig 15 5 Ensure that both ends of the line are straight and are even in length Fig 16 NOTE There is a built in line cutter that will cut and trim the lines slightly longer than desired 3 Check that the two ends of the line are even in length on both sides Fig 14 Fig 14 6 Refer to the above steps to replace another cutting line Fig 17 Fig 17 ZAWARNING For optimal performance use only replacement cutting lines designed specifically for this electric leaf mulcher
13. ore use and never use damaged or altered extension cords Follow the extension cord manufacturer s safety instructions To prevent the appliance cord from disconnecting from the extension cord during operation make a knot with the two cords as shown in Table 2 Table 1 Minimum Recommended Extension Cord Gauge AWG Chart Total length of cord in feet 120V 51 100 101 150 220V 101 200 201 300 AWG Ampere Rating Extension Cord Gauge 0 6 6 10 10 12 12 16 Not Recommended Table 2 Method of Securing Extension Cord Cord set Appliance cord A Tie cord as shown B Connect plug and receptacle Double Insulated Appliances In a double insulated appliance two systems of insulation are provided instead of grounding No grounding means is provided on a double insulated appliance nor should a means for grounding be added to the appliance Servicing a double insulated appliance requires extreme care and knowledge of the system and should be performed only by qualified service personnel at an authorized Snow Joe service dealer Replacement parts for a double insulated appliance must be identical to the parts they replace A double insulated appliance is marked with the words Double Insulation or Double Insulated The symbol o square within a square may also be marked on the appliance DOUBLE INSULATED GROUNDING NOT REQUIRED WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS This l
14. osure to dusty warm air do not stand in front of the motor ventilation slots Loading Your Machine Maintenance With the mulcher running feed double handfuls of dry leaves or single handfuls of wet leaves into the funnel Allow N WARNING D th i f ih Disconnect the appliance from the power the machine sufficient time to shred the load completely ty bef f Eaa H and regain speed before inserting the next handful Do not SuUPpY Seer carrying outany cleaning maintenance or when replacing the cutting line overload the machine by letting it labor at low speed this may cause the motor to stop If this happens turn the switch off unplug the machine clear the unshredded material from the Cleaning Your Unit funnel restart the machine and then resume shredding Your unit requires minimal maintenance to keep it in proper working order It is recommended that you clean out built N WARNING Filling the mulcher with unshredded up residue inside the motor housing area during and after material at a rate faster than the machine can handle may each use Disassemble the unit and use a cloth dampened result in permanent damage to the motor Always wear with clean water to clean the funnel cover and funnel Use protective glasses and a dust mask a dry cloth to clean the motor housing Replace the cutting line as needed and clean the air vents frequently Any other maintenance or repairs should be performed by an authorized Snow J
15. safe distance away from the machine Oo gt V amp Double Insulation Know Your Electric Leaf Mulcher Shredder It is important to know the features and safety requirements of the leaf mulcher shredder Do not use the leaf mulcher shredder for purposes or applications other than those for which the unit is intended o ON ODO aA FPF WO DH aA ih a oe ce 9 a fF WO N O Funnel cover Funnel Locking tabs 8 Clamps 2 Air vents 2 Circuit breaker Housing Height adjustment knob Plug and cable Assembling hole for legs 3 Telescoping legs 3 ON OFF switch Elastic straps Mulch adjustment control dial 0 1 in x 12 6 in 0 25 cm x 32 cm replacement cutting line 20 pcs Technical Data Rated Voltage 120 V 60 Hz Rated Power 13 amp No Load Speed 8 000 rom Particle Reduction Ratio 16 1 Max Cutting Diameter Line Diameter Line Length Weight 12 in 30 4 cm 0 1 in 0 25 cm 12 6 in 32 cm 13 4 Ibs 6 1 kg 10 11 12 Assembly ZAWARNING Do not connect to power supply until assembly is complete Failure to comply could result in accidental starting and serious personal injury Z CAUTION Carefully unpack the components of the box and verify that all parts are intact Do not separate the parts by force If any part is broken please contact an authorized service agent Unpacking 1
16. shredder Model SDJ616L Monofilament lines having a maximum diameter of 0 1 in 0 25 cm and a maximum length of 12 6 in 82 cm long may be temporarily substituted but this is NOT recommended Use of thicker lines lines made of substitute material or lines greater than 12 6 in 82 cm long may result in permanent damage to the motor and will void the manufacturer s warranty Immediately replace any worn parts of the spinner head Storage When storing the electric leaf mulcher shredder at the end of the season disassemble the unit and stack the parts in the following order Fig 18 1 Place the funnel into the box 2 Fit the motor housing into the funnel 3 Place the funnel cover onto the motor housing 4 Rest the legs in the box beside the funnel Fig 18 IS Z Service and Support If your electric leaf mulcher shredder requires service or maintenance please contact the Snow Joe customer service center at 1 866 766 9563 Model and Serial Numbers When contacting the company or reordering parts you will need to provide the model and serial numbers of your product These are found at the bottom of your electric leaf mulcher shredder Copy these numbers into the space provided below Record the following numbers from the housing or handle of your new product p Model SiD J616 Serial 10 NOTES 11 A Two Year Full Warran
17. ty for residential use in the United States and Canada General Conditions Snow Joe LLC warrants this product to the original purchaser for two years against defects in material or workmanship when used for normal residential purposes Snow Joe LLC will repair any defect in material or workmanship and repair or replace any defective part subject to the conditions limitations and exclusions set forth herein Such repair or parts replacement will be free from charge to the original purchaser except noted below The duration of the warranty applies only if the product is put to personal use around the household or residence If the product is put to any business use commercial or industrial then the duration of this warranty is 90 days from the date of original purchase If any product is rented or leased the duration of the warranty is 90 days from the date of original purchase It is the owner s responsibility to perform correctly all maintenance and minor adjustments explained in the owner s manual Electric Products To obtain a replacement electric powered unit or repair the existing electric powered unit you must return the complete unit and postage prepaid to Snow Joe Return Center 86 Executive Avenue Edison NJ 08817 Gasoline Battery Products Limitations e Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis Rechargeable batteries will be replaced free from ch
Download Pdf Manuals
Related Search