Snow Joe Sun Joe MJ502M
Contents
1. provided Fig 1 2 Attach the top handle to the lower handle using carriage bolts and knobs provided Fig 2 3 Tighten all the knobs on the joints of the handle assembly Attaching the Handle to the Mower Base Tools Required Fig 3 Pliers Not included 1 After assembling the handle line up the holes at the lower end of each handle arm with the short posts that NOTE Do not tighten the bolts completely until all bolts have extend out from the side plates of the mower base been inserted through the holes in the handle pieces 2 Clamp the both side arms to line up with the posts while pressing inwards on the handle bars Handle bars Attaching the rear bag Fig 4 amp Fig 5 Assemble bag as in Fig 4 Hook bag onto steel round bar Place locking strap from the rear bag to the center bar of the middle handle adjust strap for proper height so the bag does not rub the ground while mowing or transporting Fig 5 Operation Cutting Height Adjustment Fig 6 1 The cutting height of the 20 50 8 cm Reel Mower can be adjusted in 9 positions from 1 34 to 2 52 3 4 to 6 4 cm by moving the height adjusment levers to the desired position The height adjusment levers are located next to the smaller wheels 2 In order to set the mower to its lowest cutting position one at a time pull the adjustment levers on both sides to their highest positions 3 In order to set the mower to its highest cutt2. bar blade is polished WARNING Clean any grinding compound or debris from the cutter bar blade reel blade pinions and pawls NOTE Use industrial or valve lapping compound between 100 and 240 grit Lubricate the axle and pinion with a light film of wheel bearing grease Cleaning and Storage 1 Clean the exterior of the machine thoroughly using a soft brush and cloth before storing Do not use water solvents or polishes 2 Turn the mower on its side to clean the blade area WARNING Do not place hands in the mower near blades If grass cuttings are compacted in the blade area remove using a wood or plastic cleaning tool appropriate for the cleaning of the blades 3 Store the mower in a dry place Do not place other objects on top of the mower during storage Maintenance Tips Reel mowers are relatively low maintenance For consistent cutting follow the below instructions e Always keep the cutting bar properly adjusted Refer to the instruction manual for further directions e Regularly clean and lube cutting edges with light spray oil IMPORTANT Reel mowers have a difficult time with tall weeds such as dandelions which most times will cause the weeds to bend and not cut cut often to prevent this Service and Support If your Manual Reel Mower with Catcher requires service or maintenance please call 1 866 766 9563 for assistance Model and Serial Numbers When contacting the company or reordering parts
3. you will need to provide the model and serial numbers of your product These are found on the decal affixed to the housing or handle of your Manual Reel Mower with Catcher Copy these numbers into the space provided below Record the following numbers from the housing or handle of your new product Model M 3J3 5 0 2 M Serial SE A n e NOTES A Two Year Full Warranty GT for residential use Gm in the United States and Canada Ys General Conditions Snow Joe LLC warrants this product to the original purchaser for two years against defects in material or workmanship when used for normal residential purposes Snow Joe LLC will repair any defect in material or workmanship and repair or replace any defective part subject to the conditions limitations and exclusions set forth herein Such repair or parts replacement will be free from charge to the original purchaser except noted below The duration of the warranty applies only if the product is put to personal use around the household or residence If the product is put to any business use commercial or industrial then the duration of this warranty is 90 days from the date of original purchase If any product is rented or leased the duration of the warranty is 90 days from the date of original purchase It is the owner s responsibility to perform correctly all maintenance and minor adjustments explained in the owner s manual Electric Pr
4. Model No MJ502M a A O A Division of Snow Joe LLC IMPORTANT Safety Instructions KEEP HANDS AND FEET AWAY JANTENGA LAS MANOS Y LOS PIES A DISTANCIA GARDER MAINS ET PIEDS DISTANCE A WARNING READ ALL INSTRUCTIONS BEFORE USE A WARNING This unit can be dangerous Careless or improper use can cause serious injury A DANGER Risk of cut Keep hands and feet away from tines and cutting area Safety Information e Never place hands fingers or feet inside the reel Although this mower is not powered by a motor the reel spins when the wheels turn and it is sharp enough to cause serious injury e Never mow when grass is wet as it can be slippery e Do not use the reel mower while barefoot or while wearing sandals e Walk behind never run while using reel mower Always make sure of your footing when using this reel mower e Do not intentionally strike or hit trees fences etc This can cause injuries or severely damage the reel mower mechanisms e Make sure your reel mower is in a safe operating condition Do not attempt to operate this reel mower if damaged Contact customer service or have the reel mower repaired by a qualified repair service provider before using at all times 2011 by Snow Joe LLC All rights reserved Original instructions SYMBOLS 20 Inch Manual Reel Mower with Catcher Form No SJ MJ502M 880E OPERATOR S MANUAL DESCRIPTIONS Keep hands and feet away Safety ale
5. e moved closer to the cutting reel 1 Tighten the screws by an equal amount by turning them clockwise Align Cutting Path Indication Arrow With Previously Cut Path Fig 8 NOTE The width of the real mower actual cut is indicated below Do not use wheels as a reference point for grass cut line Checking the Adjustment Fig 9 1 Turn mower upside down 2 Inserta piece of paper between cutter bar and reel blades and slowly turn wheel by hand 3 All blades should slice the paper evenly along the entire length of the cutter bar while the reel turns smoothly 4 If mower has an intermittent cut adjustment should be made to the appropriate side of blades to attain proper cutting action ES Paper IO AX Care and Maintenance 1 Minimum care is required to ensure smooth operation of your mower 2 To avoid damage to mower or cutting blades keep area to be mowed free from debris 3 For best results regularly apply lubricant to mower s cutting surfaces cutting reel axle shaft and wheels Sharpening the Cutting Blades 1 Spread a thin layer of lapping compound on the front edge of the reel blades 2 Adjust the cutter bar so that the blade has light but firm contact across the full width of the cutter bar CAUTION Do not overtighten the adjusting screws as this could damage the cutter bar Tighten both screws during final adjustment 3 Turn the reel blades until the front edge of the cutter
6. e such design changes into previously manufactured products nor shall such changes be construed as an admission that previous designs were defective This warranty is intended to cover product defects only Snow Joe LLC is not liable for indirect incidental or consequential damages in connection with the use of the Snow Joe Products covered by this warranty This warranty does not cover any cost or expense incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non use of this product while waiting for completion of repairs under this warranty Some states do not allow exclusions of incidental or consequential damages so the above exclusions may not apply in all states This warranty may gives you specific legal rights in your state If you wish to contact Snow Joe please direct inquiries to the Customer Service Department Snow Joe Center 86 Executive Avenue Edison NJ 08817 Customers who have purchased Snow Joe products exported from the United States and Canada should contact their Snow Joe Distributor Dealer to obtain information applicable for your country province or state If for any reason you are not satisfied with the distributor s service or if you have difficulty obtaining warranty information contact your Snow Joe seller If in the event your efforts are unsatisfactory please write to the Snow Joe Center at the above address If you have any questions about your pr
7. ing position move the adjustment levers on both sides to their lowest positions NOTE The two height adjustors MUST be set to the same position height 4 The mower can be set to other cutting heights by F moving the adjustment levers to any position within their range between the highest and lowest positions ig 6 Lowest cutting position Adjustment Highest cutting position Adjusting the Mower Blade Fig 7 NOTE The blades were pre adjusted prior to leaving the factory but it is recommended that the adjustment be verified prior to first use e Vibrations during shipping can cause misalignment which often causes the blades to become too loose or too tight T his will result in a rough uneven cut or the mower will be hard to push 1 Each end of the cutting bar can be adjusted separately 2 The cutting bar blade which is located under the reel is able to pivot The two adjustment nuts located at the back of the mower move the cutting bar away from the blades when they are turned counter clockwise and closer to the blades when they are turned clockwise A WARNING Do not overtighten adjustment screw as this could damage cutter bar Both screws must be tight on final adjustment Loosening the Blades The cutter bar must be moved away from the cutting reel 1 Loosen both screws by an equal amount by turning them counter clockwise Tightening the Blades The cutter bar must b
8. oduct warranty please call 1 866 SNOW JOE or visit us online at www snowjoe com 8
9. oducts To obtain a replacement electric powered unit or repair the existing electric powered unit you must return the complete unit and postage prepaid to Snow Joe Return Center 86 Executive Avenue Edison NJ 08817 Gasoline Battery Products Limitations e Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis Rechargeable batteries will be replaced free from charge during the first 90 days After the initial 90 days batteries will be replaced at prorated cost to the customer e Idlers cables and electrical components are warranted to the original purchaser for use at household or residence for a period of two years Exclusions e Snow Joe brand engines are covered under this warranty All other engines and engine accessories are covered only by the engine manufacturer s warranty and are not covered by this warranty e Parts used that are not genuine Snow Joe parts are not covered by this warranty e Damages resulting from misuse alteration improper assembly improper adjustment neglect or accident which requires repair is not covered under this warranty e Belts augers and tines are not covered under warranty belts augers and tines wear out and can be purchased at www snowjoe com or by calling 1 866 766 9563 Snow Joe LLC may from time to time change the design of its products Nothing contained in this warranty shall be construed as obligating Snow Joe LLC to incorporat
10. rt Read the operator s manual Risk of cut Keep hands and feet away from tines and cutting area Severing of toes or fingers rotary mower blade Thrown objects and rotating line can cause severe injury Slip on slope Keep bystanders children away SAVE THESE INSTRUCTIONS Know Your Manual Reel Mower with Catcher Packing List 1 Foam Grip 2 Top handle 3 Knobs x 6 4 Center handle pieces 5 Carriage bolts x 6 6 Grass collecting bag 7 Height adjustment lever 8 Adjustable wheels rear 9 Reel mower body 10 Lower handle Technical Data Cutting width 20 50 8 cm Height adjustments 1 34 2 52 3 4 cm 6 4 cm Front wheels 10 25 cm Rear wheels 6 15 cm Weight 30 Ibs 13 6 kgs Assembly 1 Before attempting to assemble empty carton and compare parts with packing list on page 2 NOTE e Carefully remove the parts from the box e Inspect the parts to make sure no breakage or damage occurred during shipping e Do not discard the packing material until all parts are examined e lf any parts are damaged or missing please call 1 866 766 9563 for assistance e Be sure to tighten the knobs when assembled to prevent the handle from rocking Assembling the Handle Fig 1 amp Fig 2 This product normally requires 6 to 10 minutes for assembly 1 Insert the two center handle pieces into the left and right side of the top handle and secure with two knobs
Download Pdf Manuals
Related Search