American Weigh Scales SE-50 postal scale
Contents
1. American Weigh Scales SHIP ELITE User Manual SE 50 0 20kg x 1g 20 50kg x 2g 0 110 b x 0 102 Copyri A 2011 American Weigh Scales Inc All rights reserved Rev 1 1 SHIP ELITE Thank you for purchasing the American Weigh SHIP ELITE digital shipping scale Please read all operating instructions carefully before use Scales are precision measuring devices and should always be handled with proper care To ensure years of reliable service keep these simple tips in mind Do not exceed the scale s maximum capacity Overloading your scale can permanently damage it Avoid exposure to extreme heat or cold Scales perform best at normal room temperature If temperatures have changed dramatically calibration and adjustment may be necessary Allow your scale to warm up for 30 60 seconds before performing calibration and adjustment if available Store your scale in a clean dry location Dust dirt and moisture can accumulate on the weighing sensors and electronics causing inaccuracy or malfunction Avoid using your scale in close proximity to strong radio wave emitting devices such as two way radios and cordless phones Always weigh on a flat and level surface free from vibrations and drafts The corner of a room is usually the most stable Gently apply all items to be weighed Do not drop items onto the weighing platform Avoid dropping your scale The warranty does not cover damage due to rough treatment or overl2. ace and press the ON OFF key to turn the scale on 2 Once the start up process completes and the scale goes to zero you are ready to weigh 3 Place the quantity to be weighed onto the weighing platform 4 Wait a couple seconds for the display to stabilize before taking a weight reading VI Clock Mode When the scale is turned off the display will show a clock Clock Mode To set the current time follow these instructions 1 With the scale turned off Clock Mode press the SET key 2 The minutes place will begin to flash Press the MODE key to increase the minutes Press TARE to decrease the minutes Press SET to confirm the minutes 3 The hours place will begin to flash Press the MODE key to increase the hour Press the TARE key to decrease the hour Press SET to confirm the hour 4 The clock is now set NOTE Time is displayed when the scale is turned off Loss of power to the indicator will result in a reset of the clock VII Changing the Unit of Measure 1 Press the MODE key to change the scales displayed unit of measure 2 f the scale is turned off then back on it will default to the last unit used e SHIP ELITE Units Ib pound Ib oz pound ounce kg kilogram kg g kilogram gram Vill Using the Tare Feature You can use this scale s tare feature to subtract the weight of an empty container or vessel for net weight determination NOTE The weight of the container will subtract from the available capacity 1 Place the empty
3. container or vessel on the scale platform 2 Press the TARE key once The display will then reset to zero If the container is removed it s weight will be displayed as a negative number 3 You may now fill the container with the quantity to be weighed The display will show tjust the weight of the contents 4 To return to normal weight display remove any items from the weighing platform and press the TARE key again to re zero the scale IX Calibration Calibration and adjustment are performed at the factory Only advanced users should perform adjustments if there is determined to be a scale error To check calibration 1 Place the required calibration weight on the scale and note the displayed value 2 f the displayed value is not within acceptable tolerance see chart below adjustment is required Model Acceptable Calibration Recommended Tolerance Weight Accuracy Class SE 50 4g 20kg OIML M2 X Adjustment Do not proceed without a 20kg calibration weight 1 Press and hold the MODE key until the display shows CAL 2 Press the MODE key again The display will flash CAL followed by the calibration weight value see chart 3 Place the required calibration weight on the center of the platform 4 The display will show PASS then return to normal weighing mode Calibration is complete SHIP ELITE XI Troubleshooting Problem Scale will not turn on e Solution Check the batteries or AC adapter e Proble
4. m Displayed weight fluctuates randomly e Solution Make sure your workspace is stable and free of any air currents vibration or magnetic fields Static electricity can also cause fluctuations e Problem Displayed weight is inaccurate e Solution Perform a calibration adjustment XII Error Codes 1 OUTZ Zero range has shifted Perform calibration adjustment If the problem persists the load cell may be permanently damaged due to overloading 2 0 LD Maximum capacity exceeded Remove the extra weight to avoid damaging the load cell 3 L Batteries are low Replace the batteries SHIP ELITE SE 50 Max Capacity 0 20kg 0 44lb 20 50kg 44 110Ib Readability 1g 0 10z 2g 0 10z Min Capacity 4g 0 20z 2 x AAA Batteries or AC Adapter 6V DC 1000mA 120 seconds of non use No auto off when using AC Adapter Power Auto Off Time Platform Dimensions 8 0 x 8 0 x 1 8 in Warranty 10 Year Limited Warranty
5. oad Check the batteries first if you are having any trouble with your scale This simple step can remedy most scale issues Do not disassemble your scale This product contains no user serviceable parts l Part List 1 Weighing Indicator Display 2 Scale Platform Base 3 Coiled Cable to connect Base and Indicator 4 AC Adapter 5 AAA Batteries x2 ll Indicator Setup 1 Remove the parts from the box 2 Connect one end of the included cable to the side of the scale platform and the other end to the indicator display Indicator S le l u pa 2 Bottom of Indicator o wall outle e 6 lO Optional Battery Installation lll Key Description SHIP ELITE ON ey TARE MODE Ser V i 2 3 4 1 ON OFF Key Press to turn the scale ON or OFF 2 TARE Key Rezeros the scale Used to remove the weight of a container Decreases value during clock setup 3 MODE Key Changes the displayed unit of measure Increases value during clock setup 4 SET Key Enters the clock setup mode IV Battery Installation 1 Before using the scale for the first time check the battery compartment and remove any plastic insulation strips or packaging that may be in place to prevent battery drainage during shipping storage SHIP ELITE 2 If you are replacing the batteries make sure the positive and negative contacts are properly aligned V Operation 1 Place the scale platform on a flat level surf
Download Pdf Manuals
Related Search