SYBA SD-PEX24009
Contents
1. U ser M anua 1 SE MANL EGLN R1 EN 1 INTRODUCTION This Gigabit Ethernet PCI Express Card is a high performance 10 100 1000 BASE T Ethernet LAN controller is perfectly for home and office use It provides a low cost solution for connecting to a high speed Local Area Network with a data transfer rate up to 1000Mbps over a group of 4 twisted pair copper wires to a distance of maximum 100 meters away It is 100 times faster than and yet 100 fully backward compatible with 10 100BASE T system therefore it can be easily plugged into almost any existing network with CAT 5 cabling FEATURES AND SPECIFICATION e Complies with PCI Express Revision 1 1 Supports standard and low profile chassis e 1 Lane x1 PCI Express with transfer rate 2 5Gb s full duplex channel e A high performance 1000BASE T Ethernet controller card e Backward compatible to 10 100BASE T networking e 10 100 1000Mbps data rate auto negotiation operation e Compatible to existing CAT 5 UTP cabling e Fully compliant with IEEE 802 3 802 3u 802 3ab Supports full duplex flow control IEEE 802 3x e Supports IEEE 802 1P Layer 2 Priority Encoding e Supports IEEE 802 1Q VLAN tagging Crossover Detection and Auto Correction operation e Ideal for home and office use e Supports Microsoft Windows 98SE ME 2000 XP 32 64 bit Server 2003 32 64 bit Vista 32 64 bit Server 2008 32 64 bit Windows 7 32 64 bit SCO Unix Linux FreeBSD Novell DOS and Mac OS X 10 4 x or abov2. e PACKAGE CONTENTS Please check whether the package contains the following items If any item is missing or damaged please contact the retailer as soon as possible e Gigabit Ethernet PCI Express Card x 1 e User manual x 1 Driver CD x 1 HARDWARE amp SOFTWARE INSTALLATION WARNING Before installing and activating RAID function please make sure you have a complete backup of your existing data from your hard drives Manufacturer is not responsible for data loss due to abuse misuse or neglect Should you have any installation problem please contact your dealer for assistance Before Installation Before the installation of the controller card let us make the following assumptions d be The end users must have the basic knowledge of installing an internal device and its driver to a PC If they are not sure about their abilities or have any queries please call their local dealers immediately or find somebody who are experienced and qualified for assistance The computer has been properly installed with the supported operating system Installing the Controller Card into the Computer S Turn off your computer and all external devices connected to it 2 Disconnect your computer from the power sources 3 4 Find an available PCI Express x1 slot and remove the slot bracket Save the bracket screw for later Open the computer case Refer to your computer user manual for more details use Align the con
3. in this manual are subject to change without prior notice All brand names and trade names referenced and mentioned in this manual are property of their respective owners 3
4. r Other Operating Systems Please refer to the installation documents in the relevant folder on the Driver CD to install driver To obtain the latest drivers please refer to the Updating Drivers section below Notice When the device driver is properly installed there will not be any question and exclamation mark shown against this device If yes check the following 1 The driver for the network controller card is installed straightly according to the procedure listed above 2 If an older version driver is installed previously The driver for a similar product is installed 4 In the worst case the network controller card is defective Please contact your local dealer or Oo distributor immediately GETTING THE LATEST DRIVER SOFTWARE amp DOCUMENT 1 Please go to http www drivers download com 2 In Drivers Search section enter the Download code DL code DL 0263212 to search for the latest driver software and document Or you can download the latest driver from Realtek website Please go to http www realtek com Select Downloads Select Communications Network ICs Select Network Interface Controllers Select 10 100 1000M Gigabit Ethernet Select PCI Express Select Software The final page shows all the available software for RTL8111x Select and download your desired operating system driver a sd Gh th ae te Oe All contents and specification mentioned
5. troller card horizontally with respect to the slot and insert it into the slot firmly and evenly Take care not to force it into the slot Once you have properly positioned the controller card into the slot fasten it to the computer case with the screw you have just saved Connect the system to network by inserting the 8 cored CAT 5 cable not included in the package into RJ45 connector on the network controller card Secure the computer case and switch on your computer Installing Windows Driver i re 3 Turn on the computer Once Windows is running a new network controller card is detected If the Windows asks for driver for the network controller card then insert Driver CD into the optical drive Assume the optical drive letter is D Browse to the following path Assume the Windows OS used is Windows 7 D Realtek RTL8111 Windows 7 Execute setup exe to install the driver Follow the on screen instructions until the driver is totally installed Checking the status of the installed driver 1 Right click on the icon of My Computer and choose Properties 2 Choose Device Manager 3 Left click on the sign of the Network Adapters 4 The following device should be shown Realtek PCIe GBE Family Controller 5 Right click on the device above and choose Properties 6 Check the Device status in the General window The following should be shown This device is working properly Installing Driver fo
Download Pdf Manuals
Related Search