Hunter 52" Low Profile III Plus
Contents
1. LELI KLL www HunterFan com 1 888 830 1326 Congratulations on purchasing What to Expect with your new Hunter ceiling fan It will Your Installation Tools Needed Ceiling Bracket Preparation provide comfort and performance in your home or office for many years This installation and operation manual contains complete instructions for installing and operating your fan We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world To register your fan please visit www HunterFan com register Save your receipt for proof of purchase M3516 01 03 04 13 Hunter Fan Company What to Expect with Your Installation If you are unfamiliar with wiring use a qualified electrician Must be able to secure the fan to building structure or a fan rated outlet box Know your wiring You may need a friend to help you Check box to see fan weight 30 inches from blade tip to nearest wall or obstruction 7 feet from bottom edge of blade to the floor Ca Assess location M3516 01 03 04 13 Hunter Fan Company q www HunterFan com 1 888 830 1326 Read and Save These Instructions This product conforms to UL Standard 507 A WARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box mark2. acket into the outlet box Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box M3516 01 03 04 13 Hunter Fan Company Motor Housing Raise the motor housing up over the motor and ceiling bracket Turn the motor housing so the screw holes align and the indentation in the housing locks into place with the notch in the ceiling bracket The motor housing is not secured until the next step is complete Do not leave unattended Housing Screw Q With a Phillips head screwdriver install the four motor housing screws found in the hardware bag Tighten all four screws securely M3516 01 03 04 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Blades www HunterFan com 1 888 830 1326 Insert grommets found in the W hardware Lightly attach the blade irons to the bag into the holes in the blades then motor with screws found in secure each blade to a blade iron with the X hardware bag then securely screws found in the A hardware bag tighten after both screws are attached Your blades are shielded with Dust Armor which is ananotechnology coating that repels dust For cleaning the fan use soft brushes or cloths to prevent scratching Cleaning agents may damage the finishes M3516 01 03 04 13 Hunter Fa
3. breakers to the outlet box associated with the wall switch location Make sure all four 4 bumpers are still attached M3516 01 03 04 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Use wood screws Use machine screws included when securing provided with outlet to support structure with box when securing to approved electrical outlet existing ceiling fan rated box Drill 9 64 pilot holes outlet box Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31 8 kg 70 Ibs the hardware bag or less Refer to warning w 1 on pg 2 Ceiling Bracket continued Preparation M3516 01 03 04 13 Hunter Fan Company www HunterFan com 1 888 830 1326 Time Saver Tip Get a helper to insert grommets found in the I hardware bag into the blades while you re doing the next couple of steps Hanging the Fan www HunterFan com 1 888 830 1326 Ground Wire Locking Screw While holding the wires out of the way lift Once the motor is in the ceiling the motor assembly and place the square bracket use the two locking screws hanger into the opening in the ceiling found in the amp hardware bag to secure bracket Be sure the ground wire attached the moto
4. ed acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel w 3 To reduce the risk of fire electrical shock or motor damage use only Hunter Solid State Speed Controls w 4 To reduce the risk of personal injury do not bend the blade brackets when installing the blade brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades A CAUTIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician c 2 Use only Hunter replacement parts Tools Needed MI Ladder www HunterFan com 1 888 830 1326 e Power Drill 9 64 Drill Bit Screwdrivers optional optional If mounting to a support structure you will also need these tools M3516 01 03 04 13 Hunter Fan Company Ceiling Bracket To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit
5. emoving a light kit call customer service 1 888 830 1326 M3516 01 03 04 13 Hunter Fan Company e Troubleshooting www HunterFan com 1 888 830 1326 Fan doesn t work Excessive wobbling Noisy Operation Make sure power switch is on Tighten all of the blade and Tighten the blade and blade blade iron screws until they iron screws until they are snug Pull the pull chain to make sure are snug it is on e Check to see if any of the e Use the provided balancing blades are cracked If so replace Push the motor reversing switch kit and instructions to balance all of the blades firmly left or right to ensure that the fan it is engaged Check the circuit breaker to ensure the power is turned on Make sure the blades spin freely Turn off power from the circuit breaker then loosen the canopy and check all the connections according to the wiring diagram on page 7 Check the plug connection in the switch housing M3516 01 03 04 13 Hunter Fan Company
6. housing screw Tighten all three screws securely Make sure the lower switch housing is securely attached to the upper switch housing Failure to properly secure all three assembly screws could result in the light fixture falling Light Kit continued t a Install a CFL bulb Loosen the thumbscrews Insert the globe into the fixture and retighten the thumbscrews securely Do not overtighten www HunterFan com 1 888 830 1326 Connect the appropriate pull chain pendant to each of the short chains coming from the switch housing The fan pull chain controls the speed from high to off The light pull chain controls the light fixture on and off See next page for fan operation instructions M3516 01 03 04 13 Hunter Fan Company Maintenance Operation amp Cleaning www HunterFan com 1 888 830 1326 By Globe Changing the bulb unscrew the Changing the direction of air Cleaning the fan use soft thumbscrews while supporting flow move the reverse switch brushes or cloths to prevent the globe with your other hand to the opposite position scratching Cleaning products Carefully remove the globe may damage the finishes Unscrew the bulb and replace with a bulb of same type and wattage Reinstall the globe assembly For questions regarding r
7. n Company Switch Housing Q Screw two 2 housing assembly screws from the hardware bag halfway into the motor housing It does not matter which two screw holes you choose Feed the wire plug through the center hole of the upper switch housing then wrap keyhole slots around the screws and twist counterclockwise M3516 01 03 04 13 Hunter Fan Company www HunterFan com 1 888 830 1326 R Insert the third screw found in the hardware bag into place and then tighten all three 3 screws Make sure the upper switch housing is securely attached to the mounting plate Failure to properly secure all three assembly screws could result in the switch housing fixture falling Light Kit Partially install two of the switch housing screws found in the bag Connect the plugs from the upper and lower switch housings Make sure to line up the colored markings on the connectors f Want to install your fan without a light kit Go to www HunterFan com FAQs and click How do install my fan without the light kit Switch Housing g Align the notches in the sides of the lower switch housing with the upper switch housing screws Lift the lower switch housing Twist the lower switch housing clockwise to lock into place M3516 01 03 04 13 Hunter Fan Company www HunterFan com 1 888 830 1326 _ Install the third switch
8. r to the ceiling bracket to the hanger faces out of the large opening in the ceiling bracket Note Fan style may vary M3516 01 03 04 13 Hunter Fan Company Using an orange wire connector from the X hardware bag connect the 3 grounding wires green green yellow stripe or bare copper coming from the ceiling fan and hanging bracket Refer to CAUTION c 1 on pg 2 6ulpunoiy Mo Ja U2215 r Note To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight For a Single Switch Using the orange wire connectors from the X hardware bag connect the black wire ungrounded from the ceiling to the black and the blue wires from the fan Connect the white wire grounded from the ceiling to the white wire from the fan I papunoi5 papunosbun www HunterFan com 1 888 830 1326 For Dual Switches Using orange wire connectors from the amp hardware bag connect the white wire grounded from the ceiling to the white wire from the fan Connect the black wire ungrounded from the ceiling to the black wire from the fan Connect the second ungrounded wire from the ceiling to the blue wire from the fan Turn the splices upward and push them carefully back through the hanger br
Download Pdf Manuals
Related Search