Home

Premier Mounts ECM-D70T flat panel ceiling mount

1. Proceed to the Selecting the Appropriate Mounting Hardware section Page 6 Visit the Premier Mounts website at http www premiermounts com ECM D70T ECM D70T1 5 NPT Pipe not included Minimum four 4 complete turns Phillips Set Screw ECM D70T NPT Pipe not NPT Threaded Coupler Screwdriver Installation Instructions ECM D70T ECM D70T1 5 P2 Selecting the Appropriate Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert If the screw you selected is longer than the 1 8 Marking the 1 8 allowance mark on the small straw or toothpick awake as shown in Figure 2 and Figure 3 do not use this DEED screw The screw length must not bypass the mark Threaded Insert Q Test each size of the screws provided The correct screws should thread easily into the mounting point and not pull out when tension is applied Proceed to the Griplate Washer Installation Gi d section ome 2 in m Small o jej lus 1 8 Small
2. Straw a a Depth Plus 1 8 Allowance or Toothpick lar or Toothpick Mark Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 7 gt v ECM D70T ECM D70T1 5 Griplate Washer Installation Premier Mounts Griplate Washers are designed to accommodate the various M4 M5 M6 and M8 hole sizes required by flat panels hi For Griplate installation the dimples must be facing the flat panel for the lower mounting points For the upper mounting points the dimples must be facing away from the flat panel Do not place excessive pressure on the back of the flat panel as this may damage your flat panel The Griplate Washer must be installed between the head of the mounting screw and the mounting bracket as shown Does your flat panel have Recessed mount points Uneven mount points Acurved back Any obstruction near the mount point If Yes you must install nylon spacers Remove the mounting brackets Griplate washers and mounting screws from the back of the flat panel Proceed to the Nylon Spacer Installation section If No skip to the Flat Panel Installation section Flat Panel Nylon Spacer Nylon Spacer Installation Premier Mounts nylon spacers allow you to attach the mounting bracket to flat panels which have recessed or uneven mount points Each nylon spacer will add distance between the mounting bracket and your flat
3. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Contact Us NORTH AMERICA EUROPE 3130 East Miraloma Avenue Unit 3 The Moorings Business Park aa Sapte USA Channel Way Longford and Canada a BAR SRG AS Coventry CV6 6RH UK Phons 1900 209 2790 Phone 44 0 24 7664 4105 Fax 1 800 832 4888 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Fax 44 0 24 7664 4165 Premier Mounts 2011 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 13
4. a 1 72 NPT extension pipe Sx Cable Routing Integrated cable management keeps installation clean and uncluttered Decorative Cover Provides a clean stylish presentation with no visible mounting hardware Rotating 360 swivel Dynamic Viewing 15 of tilt facilitates strategic placement of flat panel Centered Ultra thin design keeps center of gravity close to flat panel to reduce deflection Elliptical Signature design adds both aesthetics and rigidity Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 5 P Attaching the ECM D70T to the Ceiling A 1 or 2 NPT threaded pipe must be firmly secured to the ceiling structure before performing the following steps The Phillips set screw must be backed out in order for the NPT threaded pipe to attach to the threaded coupler Align the ECM D70T threaded coupler with the threaded end of the NPT threaded pipe Thread the ECM D70T onto the NPT threaded pipe and rotate the ECM D70T coupler clockwise until the coupler is fully threaded onto the NPT threaded pipe The coupler must be threaded onto the NPT threaded pipe a minimum of four 4 complete turns Once the ECM D70T has been firmly threaded to the 1 77 or 2 NPT threaded pipe use a screwdriver to tighten the Phillips set screw on the threaded coupler Ensure that all connections are secure and tight before proceeding to the next step
5. panel Mount Point The nylon spacers must only be installed between the mounting bracket and your flat panel The nylon spacers will fit M4 M5 M6 and M8 screw sizes oocooooooooooQ Proceed to the Flat Panel Installation section Page 8 Visit the Premier Mounts website at http www premiermounts com Installation Instructions ECM D70T ECM D70T1 5 PA Flat Panel Installation Install the mount according to the instructions provided by Premier Mounts Perform all structural reinforcements before attaching the flat panel to the ceiling mount Do not release the flat panel until the mounting bracket arms are fully resting on the elliptical mounting bar Raise the mounting bracket arms and the attached flat panel over the elliptical mounting bar of the ECM D70T itn The cable access ports face the rear of the flat panel It may be easier to pre wire any cables prior to flat panel installation see Page 10 Mounting Bracket Arms Elliptical Mounting Bar Lower and center the mounting bracket arms with the attached flat panel onto the elliptical mounting bar of the ECM D70T Do not release the flat panel until the mounting bracket arms are resting fully on the elliptical mounting bar Oneach mounting bracket arm insert and tighten an M6 x 25mm Pan Combo screw in the larger mounting hole Repeat the Flat Panel Installation instructions for the other
6. ECM D70T ECM D70T1 5 Elliptical Ceiling Dual Mount for 37 to 50 Flat Panels INSTALLATION INSTRUCTIONS RA PREMIER MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES b 9531 041 001 01 d iN E ECM D70T ECM D70T1 5 Installation To0lS terere eate aee eee a a de ero aru E eb UA eret e br e oue erus 3 M ucadc RE EI 3 aule loai P 4 FOAUUFCS 5c m mE 5 Selecting the Appropriate Mounting Hardware sssrini aaaeaii a nennen nnnm 7 Griplate Washer Installation 0 ccccccceeececeeeeeeeeeeeceeeeeeeeeeeceaaaanaeceeeeeeeeeeeecaceaaaaeaeseeeeeeeesseeeeesensaneeeeeees 8 Nylon Spacer Installation corra o iac oaa Y pte ota a ord y Y bmc neg v redu aded var 8 Flat Panel Installation nr aE e XR EXSERNRUKE ER KEEREEUERA E AMNES SKK N OA 9 Cable Manage MEM vs annie reet eo a eec a ent a duo ral a ace at Fo ui vu d a du 10 Tilt Positioning ee a a a e a a A a a ea a a a aI 11 Optional Mounting Configurations and Accessories ssssssssseeene a aa 11 Technical Specificaltioris ere aa a RAN SSRERERRETIRERRVeRS RR NRRNRAERERRERFRA RN S sadeadegnaseaacadnaveabentiane 12 LAM ONA 13 BISEUUI PLE 13 Weight Capacity THE CEILING STRUCTURE MUST BE CAPABLE OF HOLDING Maximum flat panel weight 1 80lbs FIVE 5 TIMES THE WEIGHT OF THE FLAT PANEL AND MOUNT IF NOT THEN THE CEILING STRUCTURE MUST BE REINFORCED Warning St
7. ER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
8. able Height Adapter AST 2446 1 72 NPT Adjustable Height Adapter a ECM ENS ECM MPC ECM MAC2 Enseo HD2000 Adapter Media Player Adapter Mac mini Adapter Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 11 24 ECM D70T ECM D70T1 5 Technical Specifications All measurements are in inches mm Page 12 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt d ECM D70T ECM D70T1 5 m PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMI
9. atements INSTALL THE MOUNT ACCORDING TO THE INSTRUCTIONS PROVIDED BY PREMIER MOUNTS PERFORM ALL STRUCTURAL REINFORCEMENTS BEFORE ATTACHING THE FLAT PANEL TO THE CEILING MOUNT USE THE APPROPRIATE LIFTING DEVICE WHEN LIFTING THE FLAT PANEL INTO PLACE PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS O gt SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in the ceiling Cutting or drilling into an ele
10. com ECM D70T ECM D70T1 5 P2 Tilt Positioning Adjusting the Flat Panel Friction Tilt Angle Adjusting the Flat Panel to the Original Position Place one hand at the center top edge of the Place one hand at the center top edge of the flat flat panel panel Place the other hand on the center bottom Place the other hand on the center bottom edge of edge of the flat panel the flat panel Using the upper hand gently pull the top of Using the upper hand gently push the top of the the flat panel towards you while the flat panel towards the wall while the lower hand lower hand gently pushes the bottom of the gently pulls the bottom of the flat panel away from flat panel away from you the wall If additional tilt friction is required tighten the lower nut and lower bolt only to increase the tilt friction Lower Bolt Lower Nut Optional Mounting Configurations and Accessories The ECM D70T is designed for use with either a standard piece of 1 72 NPT or 2 pipe or any the following ceiling mount adapters from Premier Mounts Please refer to the ceiling mount adapter installation instructions when mounting Please contact Premier Mounts at 800 368 9700 with any questions To view the complete line of our products please visit us at www mounts com I Please refer to the installation instructions that come packaged with these products for correct installation procedures APP 2446 1 72 NPT Adjust
11. ctrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the ceiling where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Visit the Premier Mounts website at http www premiermounts com Installation Instructions JQEE EEE ECM D70T ECM D70T1 5 P2 Installation Tools The following tools may be required depending upon your particular installation Tape Measure Protective Eye Wear Screwdriver Parts List Make sure that none of these parts are missing and or damaged before beginning installation If there are stop the installation and call Premier Mounts at 800 368 9700 ECM D70T Mount Hardware 1 L N Y Y X Elliptical Tlit Mount Qty 1 Mounting Bracket Arms Qty 4 Decorative Covers Qty 4 M4 x 8mm Phillips Screws Qty 4 M6 x 25mm Phillips Screws Qty 4 Thread Depth Indicator Qty 2 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Pa
12. flat panel M6 x 25mm A Do not over tighten these screws gt Screw Proceed to the Attaching the Decorative Covers section Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 9 When attaching the decorative covers verify the direction of the covers The smaller mounting hole should be in position above the larger mounting hole Place the first decorative cover over the first mounting bracket arm and push firmly into place Repeat Step 1 for the second decorative cover and mounting bracket arm Align the mounting holes On each decorative cover insert and tighten an M4 x 8mm Pan Combo screw in the smaller mounting hole The decorative covers should easily go over the M6 x 25mm Pan Combo screws Repeat the Attaching Decorative Covers instructions to attach decorative covers to the second flat panel Do not over tighten these screws Cable Management Route cables through the cable access holes and to their respective locations The cables must then be routed through the coupler up the ceiling adapter not included and into the ceiling to a pre determined source ECM D70T ECM D70T1 5 Mounting Bracket Arm Decorative M4 x 8mm Screw Screwdriver To Ceiling Ceiling Adapter Coupler Source or A V Cable Installation Instructions Page 10 Visit the Premier Mounts website at http Awww premiermounts
13. ge 3 b a P2 ECM D70T ECM D70T1 5 Parts List cont d Mounting Hardware Standard Hardware M4 x 16mm Phillips Head M8 x 16mm Phillips Head Screw Qty 12 Screw Qty 12 M4 x 25mm Phillips Head Screw Qty 12 M8 x 25mm Phillips Head Screw Qty 12 M4 x 30mm Phillips Head Screw Qty 12 M8 x 30mm Phillips Head Screw Qty 12 M5 x 16mm Phillips Head Screw Qty 12 M5 x 25mm Phillips Head Screw Qty 12 M8 x 45mm Phillips Head Screw Qty 12 M5 x 30mm Phillips Head Screw Qty 12 M6 x 16mm Phillips Head Screw Qty 12 M8 x 70mm Phillips Head Screw Qty 8 M6 x 25mm Phillips Head Screw Qty 12 Griplate M6 x 30mm Phillips Head Washers Qty 16 Screw Qty 12 M6 x 45mm Phillips Head Screw Qty 12 Universal Spacers Qty 48 Page 4 Visit the Premier Mounts website at http www premiermounts com Installation Instructions ECM D70T ECM D70T1 5 Features The ECM D70T ECM D70T 1 5 ceiling mount fits dual flat panels up to 50 in either portrait or landscape orientation It offer dynamic viewing with 360 swivel and 15 of tilt The mount s ultra thin design keep s the center of gravity close to the flat panels for better balance Integrated cable management keeps the installation clean and organized Optional brackets are available for attaching mini PCs and digital media players and servers see page 11 The ECM D70T fits a 2 NPT extension pipe while the ECM D70T 1 5 fits

Premier Mounts ECM-D70T flat panel ceiling mount

Contents

Download Pdf Manuals

Related Search

Related Contents