AMX MST-431
Contents
1. AMX is not liable for any damages caused by its products or for the failure of its products to perform This includes any lost profits lost savings incidental damages or consequential damages AMX is not liable for any claim made by a third party or by an AMX Autho rized Partner for a third party This Limited Warranty does not apply to a any AMX product that has been modified altered or repaired by an unauthorized agent or improperly transported stored installed used or maintained b damage caused by acts of nature including flood erosion or earth quake c damage caused by a sustained low or high voltage situation or by a low or high voltage disturbance including brownouts sags spikes or power outages or d damage caused by war vandalism theft depletion or obsolescence This limitation of liability applies whether damages are sought or a claim is made under this warranty or as a tort claim including negligence and strict product liability a contract claim or any other claim This limitation of liability cannot be waived or amended by any person This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the possibility of any such damages This limitation of liability however will not apply to claims for personal injury Some states do not allow a limitation of how long an implied warranty last Some states do not allow the limitation or exclusion of inci den2. al EA Operation Reference Guide MST 431 MSD 431 L 4 3 Modero S Series Tabletop Touch Panel 4 3 Modero S Series Wall Mount Touch Panel Touch Panels Initial Release 7 26 2013 AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers Distributors VIP s or other AMX authorized entity AMX warrants its products to be free of defects in material and workmanship under normal use for three 3 years from the date of purchase with the following exceptions Electroluminescent and LCD Control Panels are warranted for three 3 years except for the display and touch overlay compo nents are warranted for a period of one 1 year Disk drive mechanisms pan tilt heads power supplies and MX Series products are warranted for a period of one 1 year AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products as long as the AMX lighting products are under warranty AMX also guarantees the control of dimmable loads that are properly con nected to our lighting products The dimming performance or quality there of is not guaranteed impart due to the random combi nations of dimmers lamps and ballasts or transformers AMX software is warranted for a period of ninety 90 days Batteries and incandescent lamps are not covered under the wa
3. 1 From the Settings page select the Configuration page From the Configuration page select Admin From the Admin Configuration page select Install Firmware In the Firmware Installation page select Previous ao Pon The Confirmation Dialog box FIG 18 will ask Are you sure you want to install the following firmware The option to choose Yes will be enabled after five seconds Press Yes to load the firmware listed and No to return to the Firmware Installation popup window System Message Are you sure you want to install the following firmware FIG 18 Previous Firmware installation confirmation dialog box 6 If you choose Yes the device will retrieve the files and then reboot Returning to Factory Default Firmware The MST 431 and MSD 431 L allow the option to return the device to its original factory default firmware which may be necessary in certain situations To return the device to its factory default firmware 1 From the Settings page select the Configuration page From the Configuration page select Admin From the Admin Configuration page select Install Firmware In the Firmware Installation page select Factory ao Pon The Confirmation Dialog box FIG 18 will ask Are you sure you want to install the following firmware The option to choose Yes will be enabled after five seconds Press Yes to load the firmware listed and No to return to the Firmware Installation popup window 6 If you choo
4. 3 Modero S Wall Mount FG2265 13 MXA BT Bluetooth USB Adapter for Modero X S Series FG5968 19 e MXA HST Bluetooth Handset for Modero X S Series Touch Panels FG5968 17 MXA CLK Modero X S Series Cleaning Kit FG5968 16 Memory The MSD 431 L comes with 512 MB of SDRAM and 4 GB of Flash memory neither of which can be upgraded A maximum of 2 4 GB is available to the user for projects Basic Operation The MSD 431 L is operated using its integral touchscreen as well as the Sleep button on the top of the device FIG 4 If the device has gone into its Sleep Mode a touch of the touchscreen or of the Sleep button will reactivate it Powering on the MSD 431 L The MSD 431 L may be powered on by touching and holding the Sleep button on the top of the device Microphone The MSD 431 L contains a built in microphone above the touch screen for video and audio conferencing capabilities This microphone is concealed by the casing Audio Video Capabilities The MSD 431 L has the capability of displaying multiple JPEG and PNG files at one time The device also supports streaming motion JPEG video of the sort used by many IP and Web cameras as well as MP3 and WAY audio files MST 431 MSD 431 L Features Picture View By connecting a USB drive via one of the device s USB ports FIG 3 Picture View allows the MST 431 to access JPEG images on that drive and display them on the touchscreen FIG 6 Individual images ma
5. CODE Portions of the AMX Software may from time to time as identified in the AMX Software include PRE RELEASE CODE and such code may not be at the level of performance compatibility and functionality of the GA code The PRE RELEASE CODE may not operate correctly and may be substantially modified prior to final release or certain features may not be generally released AMX is not obligated to make or support any PRE RELEASE CODE ALL PRE RELEASE CODE IS PROVIDED AS IS WITH NO WARRANTIES LIMITED WARRANTY AMX warrants that the AMX Software other than pre release code will perform substantially in accor dance with the accompanying written materials for a period of ninety 90 days from the date of receipt AMX DISCLAIMS ALL OTHER WARRANTIES EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH REGARD TO THE AMX SOFTWARE THIS LIM ITED WARRANTY GIVES LICENSEE SPECIFIC LEGAL RIGHTS Any supplements or updates to the AMX SOFTWARE including without limitation any if any service packs or hot fixes provided to Licensee after the expiration of the ninety 90 day Limited Warranty period are not covered by any warranty or condition express implied or statutory LICENSEE REMEDIES AMX s entire liability and Licensee s exclusive remedy shall be repair or replacement of the AMX Soft ware that does not meet AMX s Limited Warranty and which is returned to AMX in accordan
6. Installation Any USB peripherals mouse keyboard etc may be connected to the USB port on the rear of the device FIG 8 Updates to the device s firmware are also made via the USB port USB Port Entry for RJ45 Speaker PoE Cable FIG 8 Connectors on the rear of the MST 431 Power via Power Over Ethernet Power for the MST 431 is supplied via Power Over Ethernet PoE utilizing an AMX certified capacitive touch compliant PoE injector such as the PS POE AT High Power PoE Injector FG423 81 or other approved AMX PoE power source The incoming Ethernet cable should be connected to the RJ45 port on the device FIG 8 S WARNING NOTE MSD 431 L Installation The MSD 431 L may be installed directly into a solid surface environment using either solid surface screws or the included locking tabs for different mounting options Once installed the MSD 431 L is contained within a clear outer housing known as the back box FIG 9 This back box is removed when installing the device into a wall or into a Rough In Box FIG 9 MSD 431 L Back Box Installing the MSD 431 L into a wall The MSD 431 L comes with a clear plastic backbox designed to attach the panel to most standard wall materials This backbox has four locking tabs two on top and two on bottom to help lock the backbox to the wall These locking tabs are only extended AFTER the backbox is inserted into the wall FIG 10 and FIG 11 When installing
7. be associated for use with a single Master If the user does not assign a device number one will be assigned automatically to the panel When using multiple panels different Device Number values have to be assigned to each panel 1 Press and hold the Sleep button to open the Settings page 2 Press the Protected button enter 1988 into the on screen Keypad s password field and press Done when finished 3 Enter a Device Number value for the panel into the Device Number Keypad The range is from 1 32000 Appendix Troubleshooting 28 MST 431 MSD 431 L 4 3 Modero S Series Touch Panels Appendix Troubleshooting MST 431 MSD 431 L 4 3 Modero S Series Touch Panels 29 al EA It s Your World Take Control 3000 RESEARCH DRIVE RICHARDSON TX 75082 USA e 800 222 0193 e 469 624 8000 469 624 7153 fax 800 932 6993 technical support www amx com 7 2013 2012 AMX All rights reserved AMX and the AMX logo are registered trademarks of AMX AMX reserves the right to alter specifications without notice at any time
8. menu to open the Master Communication Settings dialog FIG 20 Master Communication Settings gt Available System s Configuration Settings System Default Settings System E lt Terminal Settings gt j lt No Active System Default Settings gt Configuration Communication Settings FIG 20 Master Communications Settings dialog box 3 Click the Communications Settings button to open the Communications Settings dialog box FIG 21 Communication Settings Platform Selection Transport Connection Option Netlink Master C TOPAP Axcess Master C Serial Modem 5 Virtual NetLinx Master User Name and Password OK Cancel FIG 21 Communications Settings dialog box ee ne NOTE 4 Click on the NetLinx Master radio button from the Platform Selection section 5 Click on the Virtual Master radio box from the Transport Connection Option section to configure the PC to communicate directly with a panel Everything else such as the Authentication is greyed out because this connection is not going through the Master s UI 6 Click the Edit Settings button on the Communications Settings dialog to open the Virtual NetLinx Master Settings dialog FIG 22 Virtual NetLinx Master Settings x Master System Number 1 The Virtual NetLinx Master connection allows G4 devices to directly connect to NetLinx Studio instead of a physical NetLinx Current Connectio
9. methods entered into the Master Connection section of the System Settings page Can t Connect To a NetLinx Master Symptom I can t seem to connect to a NetLinx Master using NetLinx Studio Select Settings gt Master Comm Settings gt Communication Settings gt Settings for TCP IP and uncheck the Automatically Ping the Master Controller to ensure availability The pinging is to determine if the Master is available and to reply with a connection failure instantly if it is not Without using the ping feature a connection may still be attempted but a failure will take longer to be recognized If you are trying to connect to a Master controller that is behind a firewall you may have to uncheck this option Most firewalls will not allow ping requests to pass through for security reasons When connecting to a NetLinx Master controller via TCP IP the program will first try to ping the controller before attempting a connection Pinging a device is relatively fast and will determine if the device is off line or if the TCP IP address that was entered was incorrect If you decide not to ping for availability and the controller is off line or you have an incorrect TCP IP address the program will try for 30 45 seconds to establish a connection Only One Modero S Series Panel In My System Shows Up Symptom I have more than one Modero S Series panel connected to my System Master and only one shows up Multiple NetLinx Compatible devices can
10. software to certain territories No software from this Site may be downloaded or exported i into or to a national or resident of Cuba Iraq Libya North Korea Iran Syria or any other coun try to which the United States has embargoed goods or ii anyone on the United States Treasury Department s list of Specially Designated Nationals or the U S Commerce Department s Table of Deny Orders AMX does not authorize the downloading or exporting of any software or technical data from this site to any jurisdiction prohibited by the United States Export Laws This Agreement replaces and supersedes all previous AMX Software License Agreements and is governed by the laws of the State of Texas and all disputes will be resolved in the courts in Collin County Texas USA For any questions concern ing this Agreement or to contact AMX for any reason please write AMX License and Warranty Department 3000 Research Drive Richardson TX 75082 Table of Contents IVEFOGUCEION sc ispicsanscascsosiarcesGrissasbasesyninsabsuaiesatinsenseeisausuiaeerd esabaueaeebaaseaeemueNtiideds 1 POSE WS Ss jccccscecsscnnneisaneccnavelsasinecuensseaueinmnancamoepestsessceccasesatasncceceusassuaeteeas sedessoniteasieeeteiess 1 MSTA 1 cccistnnsacsinesnssawstalpiasaiissiassalevslevneasiaaunsivneabiinnsencasneinabusesmuehasaiouceauysieeaeanuasnnegs 2 Connector Locations ivsssissosesiscnceseesunssnsscdeuewsesesssesensunensenrecsseepunssuursestddsnsedsesvessicouesuss 5 MGMOPy scece
11. B Micro USB 1 Micro USB host 2 0 port Firmware upgrade touch panel file transfer JPEG image viewer HID Peripherals USB audio output for headsets Bluetooth HID Profile v1 1 Keyboard Mouse Support requires MXA BT Bluetooth Adaptor Video Streaming File Formats MJPEG Audio Streaming File Formats WAV MP3 as part of touch panel file only no USB storage Intercom Full Duplex VoIP SIP v2 0 supported with AMX CSG Operating Operating Temperature 32 F to 104 F 0 C to 40 C Environment Storage Temperature 4 F to 140 F 20 C to 60 C e Humidity Operating 20 to 85 RH e Humidity Storage 5 to 85 RH e Power Heat Dissipation On 13 6 BTU hr Standby 10 9 BTU hr Dimensions HWD 3 7 16 x 5 1 16 x 2 5 16 87 mm x 128 mm x 58 mm ne MSD 431 L Specifications Cont Weight 0 5 Ibs 0 2 Kg Certifications e FCC Part 15 Class B e C Tick CISPR 22 Class B CE EN 55022 Class B and EN 55024 e CE EN 60950 1 e IC CISPR 22 Class B e VCCI CISPR 22 Class B RoHS WEEE compliant Included Accessories e MSD 431 L Quick Start Guide 93 2265 03 e MSD 431 L Installation Template 68 2265 01 Other AMX Equipment MXA MP Modero X S Series Multi Preview FG5968 20 MXA MPL Modero X S Series Multi Preview Live FG5968 10 PS POE AF TC PoE Injector 802 3AF Compliant FG423 83 NXA ENET8 2POE Gigabit PoE Ethernet Switch FG2178 63 e MSA MMK 43 Multi Mount Kit 4
12. Power Requirements PoE Power over Ethernet 802 3af class 3 Power Consumption e Full On 4W maximum e Standby 2W e Shutdown 0 6W e Start Up Inrush Current Not applicable due to PoE standard Front Panel Components LEDs Red and green LEDs on left and right side of panel used to signal room availability Sleep Button Single button on edge of panel for placing panel in sleep mode for powering off the panel and for accessing the Settings Pages Microphone 42dB 3dB sensitivity FET microphone Speakers 4 ohm 2 Watt 300Hz cutoff frequency Rear Panel Components Micro USB Port 5 pin Micro USB connector used for firmware upgrades Ethernet 10 100 Port 10 100 Base T RJ 45 connector for Ethernet connectivity and PoE Touch Panel Display Display Type TFT Active Matrix Color LCD Display Size 5 x 3 4 128 mm x 87 mm 6 152 mm diagonal Viewable Area 3 7 x 2 1 95 mm x 54 mm 4 3 109 mm diagonal W x H Viewing Angle 60 60 65 65 Up Down Left Right Screen Resolution 480x272 WxH Aspect Ratio 16 9 WxH Brightness 350 cd m Contrast Ratio 600 1 Color Depth 16 7M colors Backlight Type LED Touch Overlay SmoothTouch Communications Ethernet Ethernet 10 100 port RJ 45 connector Supported IP and IP based protocols UCP TCP ICMP ICSP IGMP DHCP Telnet FTP DNS RFB for VNC HTTP US
13. available USB port This may require disassembling the MSD 431 L to access the USB ports if a USB extension was not already installed 3 Turn on the MST 431 and MSD 431 L and allow it to boot up When it has booted up press and hold the Sleep button for 3 seconds to open the Settings page CENE A Status gt 38 Display gt dl Sounds gt Date amp Time gt o Connection amp Networks gt x Configuration amp gt FIG 16 Settings page 4 From the Settings page select the Configuration page This may require entering a password From the Configuration page select Admin From the Admin Configuration page select Install Firmware In the Firmware Installation page select New ONO The Confirmation Dialog box FIG 18 will ask Are you sure you want to install the following firmware The option to choose Yes will be enabled after five seconds Press Yes to load the firmware listed and No to return to the Firmware Installation popup window 9 The touch panel will now prompt you to remove the USB stick to continue When the USB stick is removed the touch panel will reboot System Message Are you sure you want to install the following firmware FIG 17 New Firmware installation confirmation dialog box Upgrading from Previous Firmware The MST 431 and MSD 431 L allow the option to revert the device to the previous firmware run before an upgrade To upgrade the device from previously loaded firmware
14. ce with AMX s current return policy This Limited Warranty is void if failure of the AMX Software has resulted from accident abuse or misapplication Any replace ment AMX Software will be warranted for the remainder of the original warranty period or thirty 30 days whichever is longer Outside the United States these remedies may not available NO LIABILITY FOR CONSEQUENTIAL DAMAGES IN NO EVENT SHALL AMX BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION OR ANY OTHER PECUNIARY LOSS ARISING OUT OF THE USE OF OR INABILITY TO USE THIS AMX SOFTWARE EVEN IF AMX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITA TION MAY NOT APPLY TO LICENSEE U S GOVERNMENT RESTRICTED RIGHTS The AMX Software is provided with RESTRICTED RIGHTS Use duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph 1 ii of The Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 or subparagraphs 1 and 2 of the Commercial Computer Software Restricted Rights at 48 CFR 52 227 19 as applicable SOFTWARE AND OTHER MATERIALS FROM AMX COM MAY BE SUBJECT TO EXPORT CONTROL The United States Export Control laws prohibit the export of certain technical data and
15. com 2 Click on the desired Kit file link and after accepting the Licensing Agreement verify download of the Modero Kit file to a known location 3 Select Tools gt Firmware Transfers gt Send to NetLinx Device from the main menu to open the Send to NetLinx Device dialog FIG 24 Verify that the panel s System and Device number values match those values listed within the System folder in the OnLine Tree tab of the Workspace window Seaton bo kk r Location Target Device 0 Port 1 System Lo Please select a file to send C7 Virtual NetLinx Master lt 192 168 220 42 gt Comm irtual NetLinx Master ae ae Reboot Device Ce i x FIG 24 Send to NetLinx Device dialog window 4 Select the appropriate Kit file from within the Browse for Folder window FIG 25 5 Select the panel s Kit file from the Files section 6 Enter the Device value associated with the panel and the System number associated with the Master listed in the OnLine Tree tab of the Workspace window The Port field is greyed out NOTE i Browse for Folder ES Choose Firmware Directory J FIG 25 Browse for Folder window 7 Click the Reboot Device checkbox if it is not already checked This causes the touch panel to reboot after the firmware update process is complete 8 Click Send to begin the transfer The file tran
16. e template is marked to ensure that the touch panel and back box are properly aligned 4 4 45 11 30 cm 2 65 6 73 cm FIG 12 MSD 431 L Installation Template Co recommended The outside edges of the template are the same dimensions as the touch panel which allows you to troubleshoot possible conflicts with wall edges P Using the included template to select the final placement of the back box is highly WARNING doors and other potential obstacles 3 After ensuring proper placement cut out the mounting surface for the back box using the MSD 431 L Installation Template as a guide dimensions is highly recommended This action provides the installer with a margin for error if the opening needs to be expanded Too little wall material removed is T Making sure the actual cutout opening is slightly smaller than the provided CAUTION always better than too much Mounting Surface Knockout Back Box Locking Tab FIG 13 MSD 431 L Back Box Installation 4 Thread the incoming Ethernetfrom their terminal locations through the surface opening FIG 13 Leave enough slack in the wiring to accommodate any re positioning of the panel The Micro USB port cannot be used while the touch panel installed in the back box The MSD 431 must be removed from the wall and the back box in order to access the Micro USB port 5 Remove the back box knockouts FIG 13 and thread the incoming wiring through the knockout hole
17. eatures offered in the Modero X Series the Modero S Series panels offer AMX engineering quality and industrial design a more rugged touch interface secure locking features and streaming Voice Over Internet Protocol VoIP and video The Modero S Series SmoothTouch display offers the best blend of resistive amp capacitive technologies including single touch gestures A glass overlay improves display quality while extending the touch panel s lifespan and eliminates pillowing of the touch screen surface The resultant SmoothTouch display works with fingers gloves or pointing devices and resists dirt water and light It also has the benefit of working in environments with high electrical noise Features Architectural Design Consistency Install both Modero S and Modero X touch panels throughout a facility for consistent style on any budget Mount to Any Smooth Surface Including Glass Use the optional Multi Mount Kit and mount the Modero S wall touch panel to any smooth surface without drilling or cutting Elegant Room Availability Bar Easily glance down the hall to see if meeting spaces are occupied Powerful Graphics Powered by G4 the Modero S Series features streaming video and brilliant 24 bit color depth MST 431 The Modero S Series is a touch panel family sophisticated enough for room control yet priced right for the most cost sensitive installations including small huddle spaces and dedicated room sch
18. ecestecedseesansewenensaseesseces 10 CONFIG UP ATION xixock fas dSccied enti daedevenscerscececansbievenduniveskinnctbencanatasveseverniunciucdeaietieeseieesk 11 Bluetooth SUP POF o scseccscccssc sss sesncsns dceeecsisesonssnsecsseesdedensdissnessaneceeseovaceesedsenbuneesauenss 11 Cleaning the Touch Overlay and Case ovis sccccessesscescsecessessssceisvssainensseestescencesicaestbiapare 11 Installation lt ia53 icccnasusaniasuae sacs iensor eri earen EEEE EE O E EEE a eE aer A 13 MST 431 Installation iciccsicecciscsuce cnccndvacectcansteaciceukostaevencenheactintccboenaeeciovseuncateectadsenes 13 Power via Power Over Ethernet ss sssisssissssessssisssnssssssssossoscssevseserosscats stasiun Esa Esp ossis 13 MSD 431 L Installation siccscsiiececcsssescdcisnnsssceasondcieiscduesessnsensoneceapenseivenecsseasvensbceusstesds 14 Installing the MSD 431 L into a wall seeseeesseseseeesesesessesssresesssseererseseeeessseeeessseeeeesseeeeess 14 Uninstalling the MSD 43 1 L scciiscces seco csssssacecestsncas sececessavessecsaetissecsseeastvsenecasoecsbstents 18 Configuration and Programming ssssssncsncsccorsanossensedisnesssnnedcosscessdunossniowsanoacoassaans 19 Modero S Series Programming Guide esseeeeeeeeeeseseeessrsrsssssseseerccresesssssesereeeeeeessssee 19 Upgrading Firmware srccnsiccinsscaccuspecssssncassacnnsaasvennsusbacuaaniamenniensarn aaae aai aaaea 21 Upgrading Firmware via USB Stick cccsscciccsessassesceccssess cosessesevenssscestsesssectssasteeea
19. eduling applications The smallest of our Modero S tabletop touch panels the MST 431 Modero S Series 4 3 Tabletop Touch Panel FG2265 07 FIG 1 still features the advanced technology empowering users to conduct seamless meetings including VoIP brilliant 24 bit color depth PoE connectivity USB and streaming video 3 22 _ 81 66 mm Sleep Button Wayne Industries Room 101 BD are WOS Thursday May 16 2013 ROOM AVAILABLE Subject 1 Next Meeting C 2 00 PM 3 00 PM CREATE MEETING RING DOORBELL TEST LED sor Fas Exe Microphone 4 5 04 128 mm FIG 1 MST 431 touch panel The MST 431 features a 5 x 3 4 128 mm x 87 mm 6 152 mm diagonal 6 0 152 mm diagonal display with a viewable area of 3 7 x 2 1 95 mm x 54 mm 4 3 109 mm diagonal The device communicates via Ethernet 10 100 port RJ 45 connector supported IP and IP based protocols UCP TCP ICMP ICSP IGMP DHCP Telnet FTP DNS RFB for VNC and HTTP and USB 1 USB host 2 0 Type A port The MST 431 also supports Bluetooth keyboard and mouse use via the optional MXA BT Bluetooth Adapter Sleep Button k ee 84 16 mm 3 10 78 76 mm FIG 2 MST 431 side view MST 431 Specifications Power Requirements PoE Power over Ethernet 802 3af class 2 Power Consumption Full On 4W e Standby 2W e Shutdown 0 6W e Start Up Inrush Current Not applicable due to PoE standard F
20. he device Always pull on the frame of the touch panel NEVER pull on the glass edge Configuration and Programming NOTE Programming the MST 431 and MSD 431 L require the use of the latest versions of NetLinx Studio and TPDesign 4 both available at www amx com Modero S Series Programming Guide Information on Settings pages panel configuration and programming is included in the Modero S Series Programming Guide available at www amx com Configuration and Programming 20 MST 431 MSD 431 L 4 3 Modero S Series Touch Panels Upgrading Firmware NOTE NOTE Programming the MST 431 and MSD 431 L require the use of the latest versions of NetLinx Studio and TPDesign 4 both available from www amx com Upgrading Firmware via USB stick Firmware and TPDesign 4 file downloads may be made via USB stick When looking at the device from the front the MST 431 has one USB port on the rear right of the device FIG 3 Since the MSD 431 L uses a Micro USB connection you will need an adaptor to connect a USB stick to the device To upgrade the firmware on the MST 431 and MSD 431 L to the latest version 1 Download the latest MST 431 and MSD 431 L firmware from www amx com and save it to a USB stick The firmware or panel file you intend to load needs to be located in a specifically named folder that is different for each panel type The folder names are MST 431 or MSD 431 2 Insert the USB stick into an
21. n 192 168 220 42 Master for transfers Available Connections IP Address Description 192 168 220 34 Intel R 82567LM 3 Gigabit Network Connection Ci cme FIG 22 Virtual NetLinx Master Settings 7 Within this dialog enter the Master System number The default is 1 8 In the Available Connections section click on the IP address for the touch panel to select it 9 In the Virtual NetLinx Master Settings dialog box click OK to close the box 10 In the Communications Settings dialog box click OK to close the box 11 In the Master Communications Settings dialog box click OK to save your settings and return to the main NetLinx Studio application 12 Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System The default System value is 1 13 Right click on the Empty Device Tree System entry and select Refresh System to re populate the list The panel will not appear as a device below the virtual system number in the Online Tree tab until both the system number used in step 14 for the Virtual NetLinx Master is entered into the Master Connection section of the System Settings page and the panel is restarted 14 The OnLine Tree should now display the connection to the device The Connection Status Icon on the device may take up to five seconds to register the connection Viewing devices on the Virtual System 1 After the Communication Verification dialog window ve
22. nel 4 3 FG5965 18 e MXA BT Bluetooth USB Adapter for Modero X S Series FG5968 19 MXA HST Bluetooth Handset for Modero X SSeries Touch Panels FG5968 17 e MXA CLK Modero X S Series Cleaning Kit FG5968 16 e MXA USB C USB Port Covers FG5968 18 Connector Locations With the unit facing you the single USB port for peripherals is located on the rear right side of the device FIG 3 The RJ45 connector for PoE is also located on the back of the device USB Port RJ 45 Port Speaker FIG 3 MST 431 USB port location Memory The MST 431 comes with 512 MB of SDRAM and 4 GB of Flash memory neither of which can be upgraded A maximum of 2 4 GB is available to the user for projects Basic Operation The MST 431 is operated using its integral touchscreen as well as the Sleep button on the top of the device FIG 1 If the device has gone into its Sleep Mode a touch of the touchscreen or of the Sleep button will reactivate it Powering on the MST 431 The MST 431 may be powered on by touching and holding the Sleep button on the top of the device Microphone The MST 431 contains a built in microphone on the top of the touch panel for video and audio conferencing capabilities This microphone is concealed by the casing Audio Video Capabilities The MST 431 has the capability of displaying multiple JPEG and PNG files at one time The device also supports motion JPEG video of the sort used by many IP and Web camera
23. nsctses 21 Upgrading from Previous Firmware ssssssssssscsscscesscsscsscsssssseseesessessesssssssseees 22 Returning to Factory Default Firmware ssccccccccssscssssssssssseseccesessessessssesseeees 22 Upgrading Firmware Via NetLinx Studio cccccccsssssssssesesseceeeeeseseessssssseseeeees 23 Viewing devices on the Virtual System cccccssesssssssssseceeesessscssesesssssseeeeaeesesesseeseees 24 LE a a A Downloading firmware iic 2 c lt ceccciees 05cctstvesceocesgoseetecececovedscosssus cases so ysucedecesseudociesrsoadecess 25 Appendix Troubleshooting sick hacisssicwsvacscssesusoucnssnressatwsseseveniuamanavduen termmbenines 27 OVOEPVIEW ac csccscseccsctisocansivcconasescessanesedensscoctecsscsausccwsstsrsacsetassecsennessececeaasseesstecsedeaseesns 27 Panel Doesn t Respond To Touches sscccsssssssccessssscceessssseessesssssescesssssseceeesssseeees 27 Panel Isn t Appearing In The Online Tree Tab ccssecccsssssereesecssssecesssssseecessssseeees 27 Can t Connect To a NetLinx Master ccsssssscsssssseccseeeeceeessnsnceceeeseesscesssecesenseseeeeees 27 Only One Modero S Series Panel In My System Shows Up sccccsssssseessssssseeessssees 27 Introduction The Modero S Series line of touch panels is a cousin to the popular Modero X Series with features optimized for specific needs For those customers who just want a control touch panel without all of the additional f
24. on regarding the components of the AMX Software The AMX Software is sub ject to restrictions on distribution described in this License Agreement AMX Dealer Distributor VIP or other AMX authorized entity shall not and shall not permit any other person to disclose display loan publish transfer whether by sale assignment exchange gift operation of law or otherwise license sublicense copy or otherwise disseminate the AMX Software Licensee may not reverse engineer decompile or disassemble the AMX Software ACKNOWLEDGEMENT You hereby acknowledge that you are an authorized AMX dealer distributor VIP or other AMX autho rized entity in good standing and have the right to enter into and be bound by the terms of this Agreement INTELLECTUAL PROPERTY The AMX Software is owned by AMX and is protected by United States copyright laws patent laws international treaty provisions and or state of Texas trade secret laws Licensee may make copies of the AMX Software solely for backup or archival purposes Licensee may not copy the written materials accompanying the AMX Software TERMINATION AMX RESERVES THE RIGHT IN ITS SOLE DISCRETION TO TERMINATE THIS LICENSE FOR ANY REA SON UPON WRITTEN NOTICE TO LICENSEE In the event that AMX terminates this License the Licensee shall return or destroy all originals and copies of the AMX Software to AMX and certify in writing that all originals and copies have been returned or destroyed PRE RELEASE
25. rifies active communication between the Virtual Master and the panel click the OnLine Tree tab in the Workspace window FIG 23 to view the devices on the Virtual System The default System value is 1 2 Right click on the System entry FIG 23 and select Refresh System to re populate the list Verify the panel appears in the OnLine Tree tab of the Workspace window WotkiDbo On 3 met Virtual Master firmware Pam System 1 Devices i pk So NO gc R version and device number JE 32002 NSX Application AMX LIC v3 2 Panel firmware version and device number gt gt gt Connection Stested 12 22 51 lt lt lt TER Devices Ports l of ef C Wokpate YY Online Tree SIR Data zeio cony 4 status Fina in Fies Fina IR Faes Fite Transter Status notaications Oiagnost gt ke am Em Psnonacne RERUN of ce ov FIG 23 NetLinx Workspace window showing panel connection via a Virtual NetLinx Master Downloading firmware The panel specific firmware is shown on the right of the listed panel Download the latest firmware file from www amx com and then save the Kit file to your computer Note that each Kit file is intended for download to its corresponding panel In some cases several Kit files may be included in a zip file extract the zip file to access the required Kit file 1 If the panel firmware version is not the latest available locate the latest firmware file from www amx
26. ront Panel Components Sleep Button Single button on top of panel for placing panel in sleep mode for powering off the panel and for accessing the Settings Pages Microphone 42 dB 3 dB sensitivity FET microphone Speakers 4 ohm 1 5 Watt 500 Hz cutoff frequency Rear Panel Components USB connection 1 easily accessible USB port on back of device used for connection to keyboard mouse or USB drive Ethernet 10 100 Port and 10 100 Base T RJ 45 connector for Ethernet connectivity and PoE Cable Touch Panel Display Display Type TFT Active Matrix Color LCD Display Size 5 x 3 4 128 mm x 87 mm 6 152 mm diagonal Viewable Area 3 7 x 2 1 95 mm x 54 mm 4 3 109 mm diagonal Viewing Angle 60 60 65 65 Up Down Left Right Screen Resolution 480x272 WxH Aspect Ratio W x H 16x9 Brightness 350 cd m Contrast Ratio 600 1 Color Depth 16 7M colors Backlight Type LED Touch Overlay SmoothTouch pele MST 431 Specifications Cont Communications Ethernet Ethernet 10 100 port RJ 45 connector Supported IP and IP based protocols UCP TCP ICMP ICSP IGMP DHCP Telnet FTP DNS RFB for VNC HTTP USB 1 USB host 2 0 Type A port Firmware upgrade touch panel file transfer JPEG image viewer HID Peripherals USB audio output for headsets Bluetooth HID Profile v1 1 Keyboard Mouse Support requires MXA BT Blue
27. rranty AMX AutoPatch Epica Modula Modula Series4 Modula CatPro Series and 8Y 3000 product models will be free of defects in materials and manufacture at the time of sale and will remain in good working order for a period of three 3 years following the date of the original sales invoice from AMX The three year warranty period will be extended to the life of the product Limited Lifetime Warranty if the warranty card is filled out by the dealer and or end user and returned to AMX so that AMX receives it within thirty 30 days of the installation of equipment but no later than six 6 months from original AMX sales invoice date The life of the product extends until five 5 years after AMX ceases manufacturing the product model The Limited Lifetime Warranty applies to products in their original installation only If a product is moved to a different installation the Limited Lifetime Warranty will no longer apply and the product warranty will instead be the three 3 year Limited Warranty All products returned to AMX require a Return Material Authorization RMA number The RMA number is obtained from the AMX RMA Department The RMA number must be clearly marked on the outside of each box The RMA is valid for a 30 day period After the 30 day period the RMA will be cancelled Any shipments received not consistent with the RMA or after the RMA is cancelled will be refused AMX is not responsible for products returned without a valid RMA number
28. s 6 Thread the incoming Ethernet from the surface opening and through the knockouts 7 Push the back box into the mounting surface Insure that the locking tabs lie flush against the back box and that the back box goes freely into the opening 8 Extend the locking tabs on the sides of the back box by tightening the screws inside the box until snug Not all of the tabs must be extended to lock the back box in place but extending a minimum of the top and bottom tabs is highly recommended Apply enough pressure to the screw head to keep the box flush with the wall this ensures that the locking tabs will tighten up against the inside of the wall The back box is clear to allow visual confirmation that the tabs have been extended and are gripping the wall as well as in assisting with removal if necessary 9 Insert each connector into its corresponding location along the back of the device FIG 14 ee eae Top Micro USB RJ45 Port Port FIG 14 Rear of the MSD 431 L 10 Test the incoming wiring by attaching the panel connections to their terminal locations and applying power Verify that the panel is receiving power and functioning properly to prevent repetition of the installation C Do not disconnect the connectors from the touch panel The unit must be installed with the attached connectors before being inserted into the mounting surface NOTE 11 Latch the panel onto the top hooks on the back box and push it down onto
29. s as well as MP3 and WAV audio files MSD 431 L The MSD 431 L 4 3 Landscape Wall Mount Touch Panel FG2265 03 has a sleek style to complement the Modero X Series touch panels with a new elegant room availability indicator bar and glass mounting option Now even the smallest most cost sensitive meeting spaces can benefit from a dedicated scheduling panel without compromising the architectural beauty of the facility allowing users to view the room schedule at a glance and even reserve the room right from the panel The MSD 431 L features a 35 x 3 4 128 mm x 87 mm 6 152 mm diagonal display with a viewable area of 3 7 x 2 1 95 mm x 54 mm 4 3 109 mm diagonal The device communicates via Ethernet 10 100 port RJ 45 connector supported IP and IP based protocols UCP TCP ICMP ICSP IGMP DHCP Telnet FTP DNS RFB for VNC and HTTP and USB 1 USB host 2 0 Type A port and 1 Micro USB device port The MSD 431 L also supports Bluetooth keyboard and mouse use via the optional MXA BT Bluetooth Adapter Sleep Button Microphone 4 Wayne Industries Room 101 BA Fo NX 3 42 Right 86 75 cm to5 eae Thursday May 16 2013 ROOM AVAILABLE Subject 1 Next Meeting 2 00 PM 3 00 PM CREATE MEETING RING DOORBELL TEST LED 5 05 128 14 mm FIG 4 MSD 431 L Micro USB Port Connector for RJ 45 Port FIG 5 Rear of the MSD 431 L a E EAA MSD 431 L Specifications
30. se Yes the device will retrieve the files and then reboot NOTE NOTE System Message Are you sure you want to install the following firmware FIG 19 Previous Firmware installation confirmation dialog box Upgrading Firmware Via NetLinx Studio The MST 431 and MSD 431 L use an Ethernet connection for programming firmware updates and touch panel file transfer via NetLinx Studio If you have access to the panel s network you may transfer files directly to the panel through NetLinx Studio Firmware upgrades cannot be made through an Ethernet connected PC to the touch panel unless that PC is connected to the panel s network Upgrades cannot be made with NetLinx Studio through a USB connection to the panel from a PC For more information on firmware transfers please refer to the online help in NetLinx Studio To upgrade firmware via NetLinx Studio 1 Before starting in the device s Settings pages the panel s Master Connection must be set as either Auto the default or URL with the PC s IP address as the target For more information please refer to the Modero S Series Programming Guide available at www amx com If setting the Master Connection to Auto the panel may not always search for available NetLinx Masters Also if the Windows Firewall is not allowing the server socket on UDP 1319 the panel may not be visible 2 Launch NetLinx Studio and select Settings gt Master Communication Settings from the Main
31. sfer progress is indicated on the bottom right of the dialog 9 After the file transfer is complete the panel will automatically reboot 10 After the panel has finished rebooting right click the associated System number and select Refresh System This causes a refresh of all project systems establishes a new connection to the Master and populates the System list with devices on your particular system 11 Confirm that the panel has been properly updated to the correct firmware version Verify you have downloaded the latest firmware file from www amx com and then save the Kit file to your computer Appendix Troubleshooting NOTE Overview This section describes the solutions to possible hardware firmware issues that could arise during the common operation of a Modero S touch panel Panel Doesn t Respond To Touches Symptom The device either does not respond to touches on the touch screen or does not register the touch as being in the correct area of the screen If the screen is off The device may be in Display Sleep Mode Press and hold the Sleep button to wake up the panel The device may not be connected to power Verify that the power source is connected to the device and receiving power Panel Isn t Appearing In The Online Tree Tab 1 Verify that the System number is the same on both the NetLinx Project Navigator window and the System Settings page on the device 2 Verify the proper NetLinx Master IP and connection
32. ssctscccassecssncscctnnsscassncaccndicesesecsscceotesssacsenesccacassartenteconceceedsnciscscsauaaserdsinccsete 5 Basic Operati scesetiarcctscnsiscapcinccaveinasotectecceiansevacvonstesatnieasavensdeacsuasienatorncoumisessncaeeuss 5 Powering on the MST 43 1 sc secs nccce ce daccssscectctixsceuasecctcesuentesetascenseccesesetecapeoicousctamcenbets 5 PYM EU NG as ooo E E EEA 5 Audio Video Capabilities sssccsca scccsscsvsdeccsiscncdecsstesiescessvaiiesonesesccbisetcndesceestostestecctietasse 5 WES ID 205 I L aeaaeae eara eara EEE a ae ae Oeae ia 6 WAI h T A E 8 Basic Operation siscscssssccesccosesssssssessnensscssessenessevesesesecocenarssssnavecsawsesedessnabeseresssesansdasstes 8 Powering on the MSD 431 L oss c cccsscsccccsessassseccntecesisecstsnssseenseeecsecessdustsesssnasesesbseesesees 8 MICRO PONG icdenc sce cbexscwasicticthetech otic etencecesiiesnas niente cuecpbewsuctsnucandenebckoebeuseneteacnveanebstbecents 8 Audios Video Capabilities sec ccc csescesias dcnjpacscenacnesonteelessasnedics sateoasensicaenendepenesssaegs osisssa 8 MST 431 MSD 431 L Features lt siccssssisteussuesassicsesisaasucatiesnuusnssussudsnoansssusciabswasieswels 9 Picture VIGOW sisi cacoscccaecss cecisdassmnsindicanciwenctisasnsebaiesiepaceounsis sssedebuwassaanedeneapwsbwaieeesnsiaedes 9 Preview Mode and Normal Mode sccccceceeeeseeeseseesscceececeeeseseesseesensnceceseeeeeeenes 10 Picture View Send Command wes cccciseccssecsesnnnacosncocatcccesssescnsntnenss
33. tal or consequential damages for consumer products In such states the limitation or exclusion of the Limited Warranty may not apply This Limited Warranty gives the owner specific legal rights The owner may also have other rights that vary from state to state The owner is advised to consult applicable state laws for full determination of rights EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY AMX MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AMX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY EXCEPT AS OTHERWISE LIMITED BY APPLICABLE LAW AMX RESERVES THE RIGHT TO MODIFY OR DISCONTINUE DESIGNS SPECIFICATIONS WARRAN TIES PRICES AND POLICIES WITHOUT NOTICE AMX Software License and Warranty Agreement LICENSE GRANT AMX grants to Licensee the non exclusive right to use the AMX Software in the manner described in this License The AMX Software is licensed not sold This license does not grant Licensee the right to create derivative works of the AMX Software The AMX Software consists of generally available programming and development software product documenta tion sample applications tools and utilities and miscellaneous technical information Please refer to the README TXT file on the compact disc or download for further informati
34. the backbox make sure that the assembly is in the correct position and in the correct place Once the locking tabs are extended and locked into place removing the backbox may be difficult without having access to the back of the wall or causing damage to the wall For typical mounting surfaces such as drywall use the locking tabs as the primary method for securing the back box to the surface For thin walls or solid surfaces use mounting screws not included Locking tab Back box knockout MSD 431 L front Back box FIG 10 Side view of MSD 431 L Sleep B ack box Button knockout Locking tabs MSD 431 L front Back box knockout FIG 11 Side view of MSD 431 L material must be a minimum of 50 inches 1 27cm and a maximum of 875 inches In order to guarantee a stable installation of the MSD 431 L the thickness of the wall 2 22cm The mounting surface should also be smooth and flat NOTE The maximum recommended torque to screw in the locking tabs on the plastic back box is 5 IN LB 56 N CM Applying excessive torque while tightening the tab screws such as with powered screwdrivers can strip out the locking tabs or damage the WARNING plastic back box To install the back box 1 Prepare the area by removing any screws or nails from the drywall before beginning the cutout process 2 For best results use the MSD 431 L Installation Template 68 2265 01 to ensure proper placement FIG 12 Th
35. the bottom snaps FIG 15 Press gently but firmly on the ends until the snaps click to lock it down Latch Hooks MSD 431 L Back Box Mounting Surface Snaps FIG 15 Installing the MSD 431 L O WARNING D WARNING If you see a gap between the panel and the back box or feel any binding while locking down the panel stop immediately and verify that no cables or other items are in the way Do not force the panel into position as this can cause damage to the touch screen or the panel electronics 12 Reconnect the terminal Ethernet and USB to their respective locations on either the Ethernet port or NetLinx Master Uninstalling the MSD 431 L The MSD 431 L is held in place to the back box via latch hooks and clips on the back box FIG 15 securing it to the mounting surface In certain circumstances such as firmware updates or other maintenance that requires accessing the device s Micro USB ports the device may need to be removed from the back box The clips that lock down the MSD 431 L s bottom edge may be unlatched in order to remove the device from the mounting surface To remove an MSD 431 L from its back box 1 From the bottom pull gently outward from the back box Gently rock the panel back and forth to free the bottom from the back box 2 Rotate it up to release the top latch hooks and carefully pull the device free from the back box Take care not to damage or pull the connections on the back of t
36. tion please refer to the Modero S Series Programming Guide available at www amx com C All images must be in JPEG format PNG and other image formats cannot be viewed LJ through Picture View NOTE ee eu AA Configuration The MST 431 and MSD 431 L are equipped with Settings Pages that allow you to set and configure various features on the panels For more information on connecting and configuring the touch panels to a network please refer to the Modero S Series Programming Guide available at www amx com Bluetooth Support Both the MST 431 and the MSD 431 L allow the use of Bluetooth keyboard and mouse combinations using HID Profile v1 1 Using a keyboard and mouse with the device requires use of the MXA BT Bluetooth USB Adaptor FG5968 19 Cleaning the Touch Overlay and Case Both the MST 431 and the MSD 431 L come with the MXA CLK Modero X Series Cleaning Kit FG5968 16 which may be used to clean fingerprints and dirt from the device This kit comes with cleaning cloths and a bottle of cleaning fluid specifically for use with the device When cleaning the device do not directly spray the device with cleaning fluid Instead spray the cloth and then apply the cloth to the touch screen Do NOT use abrasives of any type to clean the device as abrasives may permanently damage or remove the device s finish MST 431 MSD 431 L Features 12 MST 431 MSD 431 L 4 3 Modero S Series Touch Panels Installation MST 431
37. tooth Adaptor Video Supported Video Codecs MJPEG Audio Supported Audio Codecs e MP2 Layer and II MP3 8 kHz 11 025 kHz 12 kHz 16 kHz 22 05 kHz 24 kHz 32 kHz 44 1 kHz 48 kHz e AAC LC 8 kHz 96 kHz e G711 with uLaw VoIP encode decode at 8 kHz File Formats WAV MP3 as part of touch panel file only no USB storage Intercom Operating Environment Full Duplex VoIP SIP v2 0 supported with AMX CSG Operating Temperature 32 F to 104 F 0 C to 40 C e Storage Temperature 4 F to 140 F 20 C to 60 C e Humidity Operating 20 to 85 RH e Humidity Storage 5 to 85 RH e Power Heat Dissipation On 13 6 BTU hr Standby 10 9 BTU hr Dimensions HWD 3 22 x 5 04 x 3 10 82 mm x 128 mm x 79 mm Weight 0 90 Ibs 0 41 Kg Certifications e FCC Part 15 Class B e C Tick CISPR 22 Class B e CE EN 55022 Class B and EN 55024 e CE EN 60950 1 e IC CISPR 22 Class B e VCCI CISPR 22 Class B e RoHS WEEE compliant Included Accessories e MST 431 Installation Guide 93 2265 07 MXA USB C USB Cover Kit FG5968 18 Other AMX Equipment MXA MP Modero X S Series Multi Preview FG5968 20 e MXA MPL Modero X S Series Multi Preview Live FG5968 10 e PS POE AF TC PoE Injector 802 3AF Compliant FG423 83 e NXA ENET8 2POE Gigabit PoE Ethernet Switch FG2178 63 e MSA STMK 43 Secure Table Mount Kit for Modero S Series Touch Pa
38. utton allows the display to stop on one particular image Press it again to resume the display procession The Next Image Saved button returns the display to the last image uploaded by Page View If the panel has not accessed all of the images available on a USB drive Page View will display the last one uploaded to date 5 On the rightmost red button select the number of seconds a selected image will be displayed in Picture View This may be selected between 5 10 15 30 and 60 seconds 6 The counter beneath the buttons displays the number of images currently uploaded by the MST 431 versus the number detected on the USB drive Preview Mode and Normal Mode Picture View has two modes Preview Mode and Normal Mode Preview Mode allows the user to configure Picture View Once a USB drive containing images is inserted into the panel the images will begin to display Touching any place on the display will result in the configuration popup to slide from the bottom of the display Picture View goes into its Normal Mode when the MST 431 goes into idle timeout while connected to a USB drive Normal Mode displays images until the touchscreen is touched or some other wakeup event is detected When the device goes back into timeout Normal Mode will return to displaying images until the USB drive is removed from the device Picture View Send Command The PIC Send Command stops either mode of Picture View or starts Preview Mode For more informa
39. y be accessed at any time or the entire collection may be displayed for predetermined times Picture View may be stopped at any time by removing the USB drive and the MST 431 will return to its default display page FIG 6 Picture View display C The maximum source resolution for Picture View is 1920x1920 pixels The maximum i displayed resolution is the same as the screen resolution NOTE To start Picture View 1 Connect a USB drive to the device Picture View will automatically recognize all available images on the drive and start displaying them on the touchscreen 2 When the images begin to display touch any place on the touchscreen to open the configuration popup menu FIG 7 If no selection is made this menu will remain in place for 15 seconds and then disappear It may be accessed again by touching anywhere on the touchscreen 3 On the leftmost amber button select between Rand images display at random and A Z images display in alphabetical order based on the name of the file 4 The four grey buttons allow scrolling through saved images and the rate of display The Previous Image Saved button returns the display to the first image uploaded by Page View The Stop button stops Page View and returns to the default panel page ue aa A A Pause Stop Resume 1779 of 1780 Counter Random Previous image Next image A Z saved saved FIG 7 Picture View configuration popup menu The Pause Resume b
Download Pdf Manuals
Related Search