Accell UltraAV
Contents
1. ACCELL connecting you UitraAV HDMI Splitter and Distribution Amplifier with HDBaseT Lite READ ME FIRST SETUP INSTRUCTIONS Thank you for purchasing the Accell UltraAV HDMI Distribution Amplifier This product is designed to provide an exceptional performance and value Please review the manual before operating and retain for future reference CAUTION 1 Ensure the unit has sufficient ventilation Do not cover ventilation openings Do not install in a confined space 2 Do not operate near source of heat Do not stack on top underneath or between other heat generating unit s including other amplifiers 3 Unplug power adapter if not used for an extended period into a surge protector or surge pro tected power source 5 Do not use near liquid or areas of heavy moisture 6 Clean unit with a clean and dry cloth only 7 This unit cannot be serviced in the field Contact Accell if service is required 8 Do not open case risk of shock shock hazard 9 Do not modify power cord or use 4 To prevent damage from power the product if the power cord is surges the unit should be plugged damaged Introduction The UltraAV HDMI Distribution Amplifier Splitter featuring HDBaseT Lite accepts a signal from a single HDMI enabled audio video source and splits the single input into 4 HDMI outputs The audio video signal is mirrored on up to 4 HDMI displays monitors projectors or TV s Over Curre2. AL CONSEQUENTIAL PUNITIVE from the connected HDMI port OR INDIRECT DAMAGES INCLUDING BUT NOT LIMITED Q One or more of the connected displays will not display a picture while TO LOSS OF DATA USE OR PROFITS HOWEVER CAUSED one or more of the displays do display a picture WHETHER FOR BREACH OF CONTRACT NEGLIGENCE OR A1 Press the RESET button on the front of the splitter to reset it OTHERWISE AND WHETHER OR NOT ACCELL HAS BEEN Alternatively turn off the power to the splitter source and displays Wait ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES YOU 60 seconds Turn the source on and the displays on Turn the splitter on AGREE THAT ACCELL S MAXIMUM LIABILITY ARISING FROM A2 The HDMI cables on the non functonal display s cannot support ANY PRODUCT SOLD BY ACCELL SHALL NOT EXCEED THE PRICE their long length Use only high quality High Speed HDMI cables Keep OF SUCH PRODUCT SOME JURISDICTIONS DO NOT ALLOW the cable length as short as possible Test by locating the non working THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN display close to the splitter Use a short HDMI cable to connect the switch DAMAGES SO THE ABOVE MAY NOT APPLY TO YOU TO THE to the TV A working TV using a short HDMI cable indicates an issue with EXTENT SUCH JURISDICTION S LAW IS APPLICABLE TO THIS the HDMI cable AGREEMENT Q The splitter is not down sampling the video and some of the TV s are WARRANTY RETURNS PROCEDURE not displaying a picture A1 Go
3. amage caused by improper placement and overheating of the splitter or the receiver is not covered by the product warranty LED Indicator Lights On initial power on all LED lights on the splitter should come on solid blue If less than the maximum number of Displays are connected to the splitter not all the outputs are used there will be no corresponding HDMI OUT blue LED for the unused output Blue lights will only appear for devices connected The HDBaseT Receiver has 4 LED indicators 1 HDCP A solid LED indicates that the HDCP handshake between the source and display has been authenticated 2 Link Indicates a connection between the Matrix and the Receiver 3 Mode A flashing LED indicates correct operation of the system 4 Power A solid LED indicates power to the receiver Infrared Control IR Q Get the message This protocol is not supported or other error message The 1x4 Splitter featuring HDBaseT Lite includes 4 pairs of Infrared Extenders 4 IR Transmitters IR TX and 4 IR Receivers IR RX The front panel of the splitter has 1 IR TX port The HDBaseT Receivers each ASSISTANCE Questions regarding this product or its product A See answer Al above and repeat the steps outlined have one IR TX port and one IR RX port Using the included extenders warranty please check out our Web site at www accellcables com you can configure the IR to control the source devices when present at Customer service can be
4. dards Unsheilded or properly terminated sheilded cable solid core Cat5e Cat6 Cat6e Cat7 or Cat7e cable can be used Stranded core is not Suggested as it can reduce signal transfer Recommended to use a continuous length of cable terminated at the matrix and receiver ends With the splitter power switch in the OFF position connect the HDMI High Speed cable from the HDMI Output of the audio video source to the HDMI Input located on the rear of the splitter Tips Use the shortest length HDMI cables possible in each point in the installation Use only High Quality and High Speed HDMI cables Next connect a Cat5e 6 cable to the HDBaseT Out 1 port on the rear of the splitter Connect the other end of the Cat5e 6 cable to the HDBaseT IN port on the rear of the HDBaseT receiver positioned near the TV Run a short High Speed HDMI cable from the HDMI Out port on the receiver to the HDMI In port on the TV Plug a provided power adapter into an AC outlet and the other end into the HDBaseT receiver Using the same steps connect the remaining displays to the splitter Important The HDBaseT Receivers when operating are warm and do require space around the housing for air circulation and coollng Do not enclose the HDBaseT receiver If placed behind a component such as a TV ensure that there is adequate space for air circulation and ambient cooling and that there is no heat being generated and transmitted to the receiver from the other device D
5. into the TV s setup and configure the resolution to match all the connected TV s The TV s should share the same resolution A2 In the source devices menu options set the source device to output a resolution that matches all the connected displays Contact Customer Support to obtain a Return Authorization RMA number RMA numbers are valid for 30 days from the date of issuance We are unable to accept returns without an RMA number Returns without an RMA number clearly printed on the Q My TV s resolution are not optimized outside of the package will be refused and returned unopened All A The splitter will query the displays and provide the highest common returns must be shipped prepaid at the expense of the shipper video resolution amongst them Example Using a 1080p source if 3 of the displays support a maximum resolution of 1080p and 1 display Accell assumes no responsibility for any inaccuracies and liability supports a maximim resolution of 720p all 4 display will operate at a for direct indirect special incidental or consequential damages resolution of 720p If the 720p TV in the example is then turned off the as a result Due to ongoing improvements Accell reserves other 3 displays can then operate in 1080p resolution Press the RESET the right to make changes to hardware packaging and any button on the front panel of the splitter to refresh the configuration The accompanying documentation without prior written notice
6. nt and Over Voltage Protection The circuit boards are equipped with both over current and over voltage protection and will automatically power down if encountered The circuit boards will restore automatically once the excessive current or voltage has passed Package Contents eHDMI Distribution Amplifier Splitter e1 Power Adapter for Matrix e4 HDBaseT Receivers e4 Power Adapters for Receivers eOwners Manual e4 Pair IR TX and IR RX 1x4 HDMI Splitter with HDBaseT Lite Model KO78C O0O8B Specifications e Connect 1 HDMI Source to up to 4 HDMI Displays e Supports HD resolutions up to 1080P and 3D e HDMI 1 4a HDCP 1 2 compliant e Data transfer speed of 6 75Gbps 225MHz e Audio formats supported DTS HD 7 1 Dolby True HD 7 1 e Deep color up to 36 bit e Maximum HDMI input output cable length Up to 16ft 5m e Maximum Cat5e 6 output cable length Up to 230ft 70m e Shelf or surface mountable e 9V DC UL Listed Power Supply for 1x4 Splitter Unit e 5V DC UL Listed Power Supplies for Receiver Units 4 Total e Input AC 50Hz to 60Hz 100 240V e Splitter dimensions 10 9 W x 1 1 H x 6 1 D 277W x 28H x 156D mm Model Number KO78C 008B specifications continued e Receiver dimensions 4 4 W x 9 H x 3 D 112W x 23H x 76D mm e Operating temperature range 5 to 131 F 15 to 55 C e Operating humidity range 5 to 90 RH no condensation Note All Cat5e 6 cables must be terminated to 568B stan
7. reached by email at support accellcables com any of the displays or phone at 510 438 9288 toll free 877 353 0772 M F 9am 5pm PST The port on the splitter labeled IR accepts an optional IR TX sending commands received from the IR RX at the display end HDBaseT 1 YEAR MANUFACTURERS WARRANTY receiver to the IR eye on a source Plug an IR RX into the IR RX Port of the HDBaseT receiver Place the end The Accell UltraAV Splitter is warranted for one year from date of the IR RX in an area that is in line of sight to the remote control of ana pai hee a a alma petra a n the event of such defects the Accell product will be repaire Plug an IR TX into the IR port on the splitter Position the end of the IR ithout ch i d ith t ti if TX in line of sight to the IR eye of the source device The IR eye is mle S a aaa a i delivered to Accell Corporation prepaid together with a copy normally a small circle on the face of the source devices that receives the of the sales receipt indicating the proof of purchase date and IR signal from its remote control place of purchase This warranty excludes defects due to normal To control multiple source devices with one IR TX stack the sources wear abuse shipping damage or failure to use the product in together and position the IR TX which is plugged into the IR port on the accordance with the instructions ACCELL CORPORATION SHALL splitter so that all the source devices can
8. receive the IR signal Blast NOT BE LIABLE FOR DAMAGES BASED UPON INCONVENIENCE from the IR TX LOSS OF USE OF THE PRODUCT LOSS OF TIME INTERRUPTED Note A remote control is not included A remote control programmed to OPERATION OR COMMERCIAL LOSS OR ANY OTHER DAMAGES control the source device s is required for IR operation WHETHER INCIDENTAL CONSEQUENTIAL OR OTHERWISE YOU UI IR Recei 5f AGREE THAT ACCELL S MAXIMUM LIABILITY ARISING FROM Ba eco ell a ANY PRODUCT SOLD BY ACCELL SHALL NOT EXCEED THE PRICE Dual Frequency 38KHZ 60KHZ Dh Bical 002D OF SUCH PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN DAMAGES SO THE ABOVE MAY NOT APPLY TO YOU TO THE Ultra IR Transmitter 5 ft EXTENT SUCH JURISDICTION S LAW IS APPLICABLE TO THIS Dual Frequency 38KHZ 60KHZ AGREEMENT This warranty gives you specific legal rights and PN B164B 003B you may have other rights that vary from state to state Ultra IR Receiver and Transmitter Pin f Powers Assignment aad LIMITATION OF LIABILITY AN eoa IN NO EVENT SHALL ACCELL CORPORATION ITS SUBSIDIARIES Troubleshooting OR AFFILIATES OR THEIR RESPECTIVE PARTNERS OFFICERS DIRECTORS EMPLOYEES SHAREHOLDERS REPRESENTATIVES Q One of the display does not show a picture or output audio OR AGENTS COLLECTIVELY ACCELL BE LIABLE FOR A Check the displays input setting to ensure it is set to receive a signal DIRECT SPECIAL INCIDENT
9. three 1080p TV s will refresh flicker then each will display a 1080p resolution picture Q My TV s resolution are not optimized A The splitter will query the displays and provide the highest common video resolution amongst them Example Using a 1080p source if 3 of the displays support a maximum resolution of 1080p and 1 display Supports a maximim resolution of 720p all 4 display will operate at a resolution of 720p If the 720p TV in the example is then turned off the other 3 displays can then operate in 1080p resolution Press the RESET button on the front panel of the splitter to refresh the configuration The 2013 Accell Corporation All Rights Reserved Accell and UltraAV three 1080p TV s will refresh flicker then each will display a 1080p are registered trademarks of Accell Corporation resolution picture
Download Pdf Manuals
Related Search