Gigabyte GA-H81-D3 motherboard
Contents
1. 1 ATX 12V 2X4 7 F PANEL 2 ATX 8 F AUDIO 3 CPU FAN 9 SPDIFO 4 SYS _FAN1 2 3 10 F USB1 F USB2 5 SATA3 0 4 11 BAT 6 SATA2 2 3 12 CLR CMOS Read the following guidelines before connecting external devices e First make sure your devices are compliant with the connectors you wish to connect Before installing the devices be sure to turn off the devices and your computer Unplug the power cord from the power outlet to prevent damage to the devices After installing the device and before turning on the computer make sure the device cable has been securely attached to the connector on the motherboard 11 1 2 ATX_12V_2X4 ATX 2x4 12V Power Connector and 2x12 Main Power Connector With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard Before connecting the power connector first make sure the power supply is turned off and all devices are properly installed The power connector possesses a foolproof design Connect the power supply cable to the power connector in the correct orientation The 12V power connector mainly supplies power to the CPU If the 12V power connector is not connected the computer will not start B EEE SIEHE ATX 12V 2X4 To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be2. Enables or disables Enhanced Intel SpeedStep Technology EIST Depending on CPU loading Intel EIST technology can dynamically and effectively lower the CPU voltage and core frequency to decrease average power consumption and heat production Auto lets the BIOS automatically configure this setting Default Auto Extreme Memory Profile X M P Allows the BIOS to read the SPD data on XMP memory module s to enhance memory performance when enabled Disabled Disables this function Default gt Profile1 Uses Profile 1 settings Profile2 Uses Profile 2 settings System Memory Multiplier Allows you to set the system memory multiplier Auto sets memory multiplier according to memory SPD data Default Auto Memory Frequency MHz The first memory frequency value is the normal operating frequency of the memory being used the second is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings Advanced Memory Settings Extreme Memory Profile X M P System Memory Multiplier Memory Frequency MHz The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu Memory Enhancement Settings Provides three different memory performance enhancement settings Normal basic performance Enhanced Stability and Enhanced Performance Default Normal Memory Timing Mode Manual and Advanced Manual allows the Channel Inte
3. Next Boot After AC Power Loss Normal Boot Enables normal bootup upon the return of the AC power Default gt Fast Boot Keeps the Fast Boot settings upon the return of the AC power This item is configurable only when Fast Boot is set to Enabled or Ultra Fast Limit CPUID Maximum Allows you to determine whether to limit CPUID maximum value Set this item to Disabled for Windows XP operating system set this item to Enabled for legacy operating system such as Windows NT4 0 Default Disabled Execute Disable Bit Enables or disables Intel Execute Disable Bit function This function may enhance protection for the computer reducing exposure to viruses and malicious buffer overflow attacks when working with its supporting software and system Default Enabled Intel Virtualization Technology Enables or disables Intel Virtualization Technology Virtualization enhanced by Intel Virtualization Technology will allow a platform to run multiple operating systems and applications in independent partitions With virtualization one computer system can function as multiple virtual systems Default Enabled Note This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website 299 Intel TXT LT Support Enables or disables Intel Trusted Execution Technology Intel TXT Intel Trusted Execution Technology provides a
4. signments please contact the chassis manufacturer SPDIF O S PDIF Out Header This header supports digital S PDIF Out and connects a S PDIF digital audio cable provided by expansion cards for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards For example some graphics cards may require you to use a S PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time For information about connecting the S PDIF digital audio cable carefully read the manual for your expansion card EY The front panel audio header supports HD audio by default Pin No Definition 8 1 SPDIFO 1 2 GND 10 F USB1 F USB2 USB 2 0 1 1 Headers The headers conform to USB 2 0 1 1 specification Each USB header can provide two USB ports via an optional USB bracket For purchasing the optional USB bracket please contact the local dealer Pin No Definition Pin No Definition 1 Power 5V 6 USB DY i ii 2 Power 5V 7 GND 3 USB DX 8 GND 4 USB DY 9 No Pin 5 USB DX 10 NC e Do not plug the IEEE 1394 bracket 2x5 pin cable into the USB header e Prior to installing the USB bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to
5. Definition Audio 2 4 5 1 7 1 channel To configure 7 1 channel audio you have to use an HD front panel audio module and enable the multi channel audio feature through the audio driver Support for S PDIF Out vr LAN Realtek GbE LAN chip 10 100 1000 Mbit W Expansion Slots 1 x PCI Express x16 slot running at x16 2 x PCI Express x1 slots The PCI Express slots conform to PCI Express 2 0 standard 3 x PCI slots Storage Interface Chipset 2 x SATA 66b s connectors SATA3 0 SATA3 1 2 x SATA 3Gb s connectors SATA2 2 SATA2 3 USB Chipset 2 USB 3 0 2 0 ports on the back panel 6 USB 2 0 1 1 ports 2 ports on the back panel 4 ports available through the internal USB headers qas Internal goe Connectors 9 9 9 9 99 9 1 x 24 pin ATX main power connector 1 x 8 pin ATX 12V power connector 2 X SATA 6Gb s connectors 2 X SATA 3Gb s connectors 1 x CPU fan header 3 x system fan headers 1 x front panel header mas Internal Ale ni Connectors 9 9 1 x front panel audio header 1 x S PDIF Out header 2 x USB 2 0 1 1 headers 1 x Clear CMOS jumper os Back Panel Connectors I O Controller 9 9 9 9 9 9 9 9 1 x PS 2 keyboard port 1 x PS 2 mouse port 1 x D Sub port 1 x parallel port 1 x serial port 2 x USB 3 0 2 0 ports 2 x USB 2 0 1 1 ports 1 x RJ 45 port 3 x audio jacks Line In Line Out Mic In ITE I O Control
6. Drivers Installation Before installing the drivers first install the operating system The following instructions use EB Windows 8 as the example operating system e After installing the operating system insert the motherboard driver disk into your optical drive Click on the message Tap to choose what happens with this disc on the top right corner of the screen and select Run Run exe Or go to My Computer double click the optical drive and execute the Run exe program Xpress Install will automatically scan your system and then list all of the drivers that are recommended to install You can click the Xpress Install button and Xpress Install will install all of the selected drivers Or click the arrow J icon to individually install the drivers you need 30 Regulatory Statements Regulatory Notices This document must not be copied without our written permission and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose Contravention will be prosecuted We believe that the information contained herein was accurate in all respects at the time of printing GIGABYTE cannot however assume any responsibility for errors or omissions in this text Also note that the information in this document is subject to change without notice and should not be construed as a commitment by GIGABYTE Our Commitment to Preserving the Environment In addition to high efficiency performance al
7. GND 2 12V 1 2 12V Speed Control Li 3 Sense SYS FAN1 2 3 Sense 4 Speed Control 4 VCC SYS FAN3 Pin No Definition 1 GND 2 12V 3 NA Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating Overheating may result in damage to the CPU or the system may hang e These fan headers are not configuration jumper blocks Do not place a jumper cap on the headers 212 5 SATA3 0 1 SATA 6Gb s Connectors The SATA connectors conform to SATA 6Gb s standard and are compatible with SATA 3Gb s and SATA 1 5Gb s standard Each SATA connector supports a single SATA device SATA3 Pin No Definition Pin No Definition 1 GND 5 RXN 2 TXP 6 RXP 1 T e EA D 4 GND 6 SATA2 2 3 SATA 3Gb s Connectors The SATA connectors conform to SATA 3Gb s standard and are compatible with SATA 1 5Gb s standard Each SATA connector supports a single SATA device Pin No Definition Pin No Definition BAUM 1 GND 5 RXN 2 TXP 6 RXP CS e TXN T GND 4 GND 7 F_PANEL Front Panel Header Connect the power switch reset switch speaker and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables e PLED PWR LED Power LED Yellow Purple Power LED Power Switch Ha
8. To turn on the system enter the password and press lt Enter gt Note To cancel the password press lt Enter gt on this item When prompted for the password press lt Enter gt again without entering the password to clear the password settings Power On By Mouse Allows the system to be turned on by a PS 2 mouse wake up event Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead Disabled Disables this function Default Move Move the mouse to turn on the system Double Click Double click on left button on the mouse to turn on the system ErP Determines whether to let the system consume least power in S5 shutdown state Default Disabled Note When this item is set to Enabled the following functions will become unavailable PME event wake up power on by mouse power on by keyboard and wake on LAN 28 2 7 a Save amp Exit C 7 1 2 aie DualBIOS f w S c 7 os SA x 3 s m A E tas j ee Tet System Intormation BIOS Features Peripherals Power Management Dashboard English Q F lash Save amp Exit Setup Save amp Exit Setup Press lt Enter gt on this item and select Yes This saves the changes to the CMOS and exits the BIOS Setup program Select No or press lt Esc gt to return to the BIOS Setup Main Menu Exit Without Saving Press lt Enter gt on this item and select Yes This exits the BIOS Setup without saving the changes made in BIOS S
9. UEFI Only Enables UEFI option ROM only gt Legacy First Enables legacy option ROM first gt gt UEFI First Enables UEFI option ROM first This item is configurable only when CSM Support is set to Always Other PCI Device ROM Priority Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other than the LAN storage device and graphics controllers Legacy OpROM Enables legacy Option ROM only gt UEFI OpROM Enables UEFI Option ROM only Default This item is configurable only when CSM Support is set to Always Network stack Disables or enables booting from the network to install a GPT format OS such as installing the OS from the Windows Deployment Services server Default Disabled Ipv4 PXE Boot Support Enables or disables IPv4 PXE Support This item is configurable only when Network stack is enabled Ipv6 PXE Boot Support Enables or disables IPv6 PXE Support This item is configurable only when Network stack is enabled Administrator Password Allows you to configure an administrator password Press Enter on this item type the password Note This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website 24 and then press lt Enter gt You will be requested to confirm the password Type the password again and press lt Enter gt You must enter the administrator
10. automatically during the process of re engaging the lever after you insert the CPU 1 4 Installing the Memory Read the following guidelines before you begin to install the memory A e Make sure that the motherboard supports the memory It is recommended that memory of the same capacity brand speed and chips be used Go to GIGABYTE s website for the latest supported memory speeds and memory modules e Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage e Memory modules have a foolproof design A memory module can be installed in only one di rection If you are unable to insert the memory switch the direction Dual Channel Memory Configuration This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology After the memory is installed the BIOS will automatically detect the specifications and capacity of the memory En abling Dual Channel memory mode will double the original memory bandwidth The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following Channel A DDR3 1 Channel B DDR3 2 Due to CPU limitations read the following guidelines before installing the memory in Dual Channel mode 1 Dual Channel mode cannot be enabled if only one DDR3 memory module is installed 2 When enabling Dual Channel mode with two memory modules it is recommended that memory of the same capacit
11. devices This item appears only when a USB storage device is installed OnBoard LAN Controller Enables or disables the onboard LAN function Default Enabled If you wish to install a 3rd party add in network card instead of using the onboard LAN set this item to Disabled SATA Configuration Integrated SATA Controller Enables or disables the integrated SATA controllers Default Enabled SATA Mode Selection Allows you to decide whether to configure the SATA controller integrated in the Chipset to AHCI mode IDE Configures the SATA controller to IDE mode AHCI Configures the SATA controllers to AHCI mode Advanced Host Controller Interface AHCI is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug Default 26 ww Serial ATA Port 0 1 2 3 Port 0 1 2 3 Enables or disables each SATA port Default Enabled Hot plug Enables or disable the hot plug capability for each SATA port Default Disabled External SATA Enables or disables support for external SATA devices Default Disabled Super IO Configuration This section provides information on the super I O chip and allows you to configure the serial port and parallel port Serial Port A Enables or disables the onboard serial port Default Enabled Parallel Port Enables or disables the onboard parallel port Default Enabled Device Mode This item is configura
12. hardware based security foundation Default Disabled VT d Note Enables or disables Intel Virtualization Technology for Directed I O Default Enabled Windows 8 Features Allows you to select the operating system to be installed Default Other OS CSM Support Enables or disables UEFI CSM Compatibility Support Module to support a legacy PC boot process Always Enables UEFI CSM Default gt gt Never Disables UEFI CSM and supports UEFI BIOS boot process only This item is configurable only when Windows 8 Features is set to Windows 8 or Windows 8 WHQL Boot Mode Selection Allows you to select which type of operating system to boot UEFI and Legacy Allows booting from operating systems that support legacy option ROM or UEFI option ROM Default Legacy Only Allows booting from operating systems that only support legacy option ROM gt UEFI Only Allows booting from operating systems that only support UEFI option ROM This item is configurable only when CSM Support is set to Always LAN PXE Boot Option ROM Allows you to select whether to enable the legacy option ROM for the LAN controller Default Disabled This item is configurable only when CSM Support is set to Always Storage Boot Option Control Allows you to select whether to enable the UEFI or legacy option ROM for the storage device controller gt gt Disabled Disables option ROM Legacy Only Enables legacy option ROM only Default gt
13. off the computer in MS DOS mode using the power button gt gt Instant Off Press the power button and then the system will be turned off instantly Default Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system If the power button is pressed for less than 4 seconds the system will enter suspend mode RC6 Render Standby Allows you to determine whether to let the onboard graphics enter standby mode to decrease power consumption Default Disabled AC BACK Determines the state of the system after the return of power from an AC power loss Always Off The system stays off upon the return of the AC power Default Always On The system is turned on upon the return of the AC power Memory The system returns to its last known awake state upon the return of the AC power Power On By Keyboard Allows the system to be turned on by a PS 2 keyboard wake up event Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead Disabled Disables this function Default Any Key Press any key to turn on the system Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system gt Password Set a password with 1 5 characters to turn on the system Power On Password Set the password when Power On by Keyboard is set to Password Press lt Enter gt on this item and set a password with up to 5 characters and then press lt Enter gt to accept
14. the USB bracket 44 11 BAT Battery The battery provides power to keep the values such as BIOS configurations date and time information in the CMOS when the computer is turned off Replace the battery when the battery voltage drops to a low level or the CMOS values may not be accurate or may be lost A You may clear the CMOS values by removing the battery 1 Turn off your computer and unplug the power cord 2 Gently remove the battery from the battery holder and wait for one minute Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 3 Replace the battery 4 Plug in the power cord and restart your computer Always turn off your computer and unplug the power cord before replacing the battery Replace the battery with an equivalent one Danger of explosion if the battery is replaced with an incor rect model Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or un certain about the battery model When installing the battery note the orientation of the positive side and the negative side of the battery the positive side should face up Used batteries must be handled in accordance with local environmental regulations 12 CLR CMOS Clear CMOS Jumper Use this jumper to clear the BIOS configurations and reset the CMOS values to factory defaults To clear the CMOS va
15. the system to emit warning sound if the fan is not connected or fails Check the fan condition or fan connection when this occurs Default Disabled CPU Fan Speed Control CPU_FAN Connector Allows you to determine whether to enable the fan speed control function and adjust the fan speed gt gt Normal Allows the fan to run at different speeds according to the CPU temperature You can adjust the fan speed with EasyTune based on your system requirements Default Silent Allows the fan to run at slow speeds Manual Allows you to control the fan speed under the Fan Speed Percentage item Full Speed Allows the fan to run at full speeds Fan Speed Percentage Allows you to control the fan speed This item is configurable only when CPU Fan Speed Control is set to Manual Options are 0 75 PWM value C 2 50 PWM value C 1st System Fan Speed Control SYS_FAN1 Connector Allows you to determine whether to enable the fan speed control function and adjust the fan speed Normal Allows the fan to run at different speeds according to the system temperature You can adjust the fan speed with EasyTune based on your system requirements Default Silent Allows the fan to run at slow speeds Manual Allows you to control the fan speed under the Fan Speed Percentage item Full Speed Allows the fan to run at full speeds 20 ww Fan Speed Percentage Allows you to control the system fan speed This item is configur
16. this setting Default Auto Turbo Ratio 1 Core Active 4 Core Active Allows you to set the CPU Turbo ratios for different number of active cores Auto sets the CPU Turbo ratios according to the CPU specifications Default Auto Turbo Power Limit Watts Allows you to set a power limit for CPU Turbo mode When the CPU power consumption exceeds the specified power limit the CPU will automatically reduce the core frequency in order to reduce the power Auto sets the power limit according to the CPU specifications Default Auto Core Current Limit Amps Allows you to set a current limit for CPU Turbo mode When the CPU current exceeds the specified current limit the CPU will automatically reduce the core frequency in order to reduce the current Auto sets the power limit according to the CPU specifications Default Auto No of CPU Coree Enabled Allows you to select the number of CPU cores to enable in an Intel multi core CPU the number of CPU cores may vary by CPU Auto lets the BIOS automatically configure this setting Default Auto Hyper Threading Technology Allows you to determine whether to enable multi threading technology when using an Intel CPU that supports this function This feature only works for operating systems that support multi processor mode Auto lets the BIOS automatically configure this setting Default Auto CPU Enhanced Halt C1E Enables or disables Intel CPU Enhanced Halt C1E functi
17. used 500W or greater If a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system ATX 12V 2X4 Pin No Definition Pin No Definition 1 GND Only for 2x4 pin 12V 5 12V Only for 2x4 pin 12V 2 GND Only for 2x4 pin 12V 6 12V Only for 2x4 pin 12V 3 GND 7 12V 4 GND 8 12V ATX Pin No Definition Pin No Definition 1 3 3V 13 3 3V 2 3 3V 14 12V 3 GND 15 GND 4 5V 16 PS_ON soft On Off 5 GND 17 GND 6 5V 18 GND 7 GND 19 GND 8 Power Good 20 5V 9 5VSB stand by 5V 21 5V 10 12V 22 5V 11 12V Only for 2x12 pin 23 5V Only for 2x12 pin ATX ATX 12 3 3V Only for 2x12 pin 24 GND Only for 2x12 pin ATX ATX 3 4 CPU FAN SYS FAN1 2 3 Fan Headers The motherboard has a 4 pin CPU fan header CPU FAN a 4 pin SYS_FAN1 SYS_FAN2 and a 3 pin SYS_FAN3 system fan headers Most fan headers possess a foolproof insertion design When connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire The speed control function requires the use of a fan with fan speed control design For optimum heat dissipation it is recommended that a system fan be installed inside the chassis poen CPU FAN A SYS FAN3 CPU FAN SYS FAN1 2 Pin No Definition Pin No Definition 1 GND 1
18. 3 co CLR_CMOS ee EE pane SPDIF_O F_USB1 F USB2 Box Contents MI GA H81 D3 motherboard MI Motherboard driver disk vI Two SATA cables vI User s Manual IV O Shield The box contents above are for reference only and the actual items shall depend on the product package you obtain The box contents are subject to change without notice GA H81 D3 Motherboard Block Diagram 1 PCI Express x16 CPU CLK 100 MHz M LGA1150 PCle CLK CPU DDR3 1600 1333 MHz 100 MHz Dual Channel Memory Pica bao pw20 roi PCI Express Bus puras Realtek d 2 SATA 6Gb s Intel H81 o 2 SATA 3Gb s x1 PCI Express Bus 2UsB3020 i Pi PCle to PC a 6 USB 2 0 1 1 PCI Bus iTE Super CODEC PS 2 KB Mouse DESS 3 3000 8999 6 DSO WO WO A BEES G 3 PCI BONA o5 589 oS Er O LT PCI CLK oa 33 MHz o5 EB For detailed product information limitation s refer to 1 2 Product Specifications _5 Chapter1 Hardware Installation 1 1 The motherboard contains numerous delicate electronic circuits and components which can be Installation Precautions come damaged as a result of electrostatic discharge ESD Prior to installation carefully read the user s manual and follow these procedures Prior to installation make sure the chassis is suitable for the motherboard Prior to installation do not remove or break motherboard S N Serial Number sticker or warranty sticker provided by your dealer These
19. Clock Allows you to set the onboard graphics clock The adjustable range is from 400 MHz to 4000 MHz Default Auto i Whether the system will work stably with the overclock overvoltage settings you made is dependent on your v CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU The adjustable range is dependent on the CPU being installed CPU Frequency Displays the current operating CPU frequency ww Advanced CPU Core Settings lt CPU Clock Ratio CPU Frequency The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu c K oc et9 Allows for increased performance by using certain CPUs Default Auto Note This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website 17 CPU PLL Selection Allows you to set the CPU PLL Auto lets the BIOS automatically configure this setting Default Auto Filter PLL Level Allows you to set the Filter PLL Auto lets the BIOS automatically configure this setting Default Auto Uncore Ratio Allows you to set the CPU Uncore ratio The adjustable range is dependent on the CPU being used Uncore Frequency Displays the current CPU Uncore frequency Intel R Turbo Boost Technology Allows you to determine whether to enable the Intel CPU Turbo Boost technology Auto lets the BIOS automatically configure
20. GA H81 D3 User s Manual Rev 1001 12ME H81D3 1001R Declaration of Conformity DECLARATION OF CONFORMITY a Importer Per FCC Part 2 Section 2 1077 a G B T Technology Trading GMbH Address Bullenkoppel 16 22047 Hamburg Germany C Declare that the product Product Type Motherboard Product Name GA H81 D3 Responsible Party Name G B T INC U S A conforms with the essential requirements of the following directives Address 17358 Railroad Street City of Industry CA 91748 Phone Fax No 626 854 9338 626 854 9326 X 2004 108 EC EMC Directive KX Conduction amp Radiated Emissions EN 55022 2010 X Immunity EN 55024 2010 hereby declares that the product q Power line harmonics EN 61000 3 2 2006 A2 2009 Product Name Motherboard x Power line flicker EN 61000 3 3 2008 Model Number GA H81 D3 X 2006 95 EC LVD Directive Conforms to the following specifications XI Safety EN60950 1 2006 A12 2011 FCC Part 15 Subpart B Section 15 107 a and Section 15 109 x 2011 65 EU RoHS Directive a Class B Digital Device X Restriction of use of certain This product does not contain any of the restricted Supplementary Information substances in electronic equipment substances listed in Annex Il in concentrations o This device complies with part 15 ofthe FCC Rules Operation is and applications banned by the directive E S subject to the following two conditions 1 This device may not
21. Installing the CPU Read the following guidelines before you begin to install the CPU A e Make sure that the motherboard supports the CPU Go to GIGABYTE s website for the latest CPU support list e Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage Locate the pin one of the CPU The CPU cannot be inserted if oriented incorrectly Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket Apply an even and thin layer of thermal grease on the surface of the CPU Do not turn on the computer if the CPU cooler is not installed otherwise overheating and dam age of the CPU may occur e Set the CPU host frequency in accordance with the CPU specifications It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals If you wish to set the frequency beyond the standard specifications please do so according to your hardware specifications including the CPU graphics card memory hard drive etc Installing the CPU Locate the alignment keys on the motherboard CPU socket and the notches on the CPU LGA1150 CPU Socket LGA1150 CPU Alignment Key E a nma ini Pin One Corner of the CPU Socket Triangle Pin One Marking on the CPU Do not remove the CPU socket cover before inserting the CPU It may pop off from the load plate
22. X CE marking cause harmful and 2 this device must accept any inference received C including that may cause undesired operation EC conformity marking Representative Person s Name ERIC LU Signature Eric Lu Signature Ti H e pP Date Jul 23 2013 Stamp Date Jul 23 2013 Name Timmy Huang Copyright 2013 GIGA BYTE TECHNOLOGY CO LTD All rights reserved The trademarks mentioned in this manual are legally registered to their respective owners Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice No part of this manual may be reproduced copied translated transmitted or published in any form or by any means without GIGABYTE s prior written permission BI In order to assist in the use of this product carefully read the User s Manual BI For product related information check on our website at http www gigabyte com Identifying Your Motherboard Revision The revision number on your motherboard looks like this REV X X For example REV 1 0 means the revision of the motherboard is 1 0 Check your motherboard revision before updating motherboard BIOS drivers or when looking for technical information Example 1 0 2 Lu ac Table of Contents GA H81 D3 Motherboard Layout sissessisanicinin 4 GA H81 D3 Motherboard Block Dia
23. able only when 1st System Fan Speed Control is set to Manual Options are 0 75 PWM value C 2 50 PWM value C 2nd System Fan Speed Control SYS FAN2 Connector Allows you to determine whether to enable the fan speed control function and adjust the fan speed Normal Allows the fan to run at different speeds according to the system temperature You can adjust the fan speed with EasyTune based on your system requirements Default Silent Allows the fan to run at slow speeds Manual Allows you to control the fan speed under the Fan Speed Percentage item gt gt Full Speed Allows the fan to run at full speeds Fan Speed Percentage Allows you to control the system fan speed This item is configurable only when 2nd System Fan Speed Control is set to Manual Options are 0 75 PWM value C 2 50 PWM value C Miscellaneous Settings PCle Slot Configuration Allows you to set the operation mode of the PCI Express slots to Gen 1 or Gen 2 Auto lets the BIOS automatically configure this setting Default Auto 3DMark01 Boost Allows you to determine whether to enhance some legacy benchmark performance Default Disabled 2 3 System Information GIGABYTE DualBIOS e z ot t 3 x E P AS P TIT BIOS Features Peripherals ower Management Save amp Exit Dashboard English Q Flash Model Name H81 D3 BIOS Version E BIOS Date 06 27 2013 BIOS ID BAOSAGOH System Language English Access Level Administra
24. ble only when Parallel Port is set to Enabled It allows you to select an operating mode for the onboard parallel LPT port Options are Standard Parallel Port Mode Default EPP Mode Enhanced Parallel Port ECP Mode Extended Capabilities Port EPP Mode amp ECP Mode Realtek PCle GBE Family Controller This sub menu provides information on LAN configuration 2 6 Power Management Cr GIGABYTE DualBIOS qeu D s c mS a NN EE I v a TAS Ip EC PEPIPEPIEEEEEE rr EE Lr PEEEN UE CE M I T System Information BIOS Features Peripherals Save amp Exit Dashboard English Q Flash Power Loading Auto Disabled Instant Power Loading Enables or disables dummy load When the power supply is at low load a self protection will activate Causing it to shutdown or fail If this occurs please set to Enabled Auto lets the BIOS automatically configur this setting Default Auto 27 Resume by Alarm Determines whether to power on the system at a desired time Default Disabled If enabled set the date and time as following Wake up day Turn on the system at a specific time on each day or on a specific day in a month Wake up hour minute second Set the time at which the system will be powered on automatically Note When using this function avoid inadequate shutdown from the operating system or removal of the AC power or the settings may not be effective Soft Off by PWR BTTN Configures the way to turn
25. bps data rate Blinking Data transmission or receiving is occurring m Green 100 Mbps data rate Off No data transmission or receiving is occurring Off 10 Mbps data rate LAN Port RJ 45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate The following describes the states of the LAN port LEDs e USB 2 0 1 1 Port The USB port supports the USB 2 0 1 1 specification Use this port for USB devices such as a USB keyboard mouse USB printer USB flash drive and etc Line In Jack Blue The default line in jack Use this audio jack for line in devices such as an optical drive walkman etc 10 Line Out Jack Green The default line out jack Use this audio jack for a headphone or 2 channel speaker This jack can be used to connect front speakers in a 4 5 1 7 1 channel audio configuration 9 Mic In Jack Pink The default Mic in jack Microphones must be connected to this jack To configure 7 1 channel audio you have to use an HD front panel audio module and enable the multi channel audio feature through the audio driver your device and then remove it from the motherboard e When removing the cable pull it straight out from the connector Do not rock it side to side to prevent an electrical short inside the cable connector 1 7 Internal Connectors i e When removing the cable connected to a back panel connector first remove the cable from
26. e computer system in a high temperature environment Turning on the computer power during the installation process can lead to damage to sys tem components as well as physical harm to the user If you are uncertain about any installation steps or have a problem related to the use of the product please consult a certified computer technician 1 2 Product Specifications CPU Support for Intel Core i7 processors Intel Core i5 processors Intel Core i3 processors Intel Pentium processors Intel Celeron processors in the LGA1150 package Go to GIGABYTE s website for the latest CPU support list L3 cache varies with CPU QQ Chipset Intel H81 Express Chipset Memory 9 9 2 x 1 5V DDR3 DIMM sockets supporting up to 16 GB of system memory Due to a Windows 32 bit operating system limitation when more than 4 GB of physical memory is installed the actual memory size displayed will be less than the size of the physical memory installed Dual channel memory architecture Support for DDR3 1600 1333 MHz memory modules Support for non ECC memory modules Support for Extreme Memory Profile XMP memory modules Goto GIGABYTE s website for the latest supported memory speeds and memory modules A Onboard Graphics Audio Integrated Graphics Processor l f 1 x D Sub port supporting a maximum resolution of 1920x1200 Maximum shared memory of 1 GB Realtek ALC887 codec High
27. etup to the CMOS Select No or press lt Esc gt to return to the BIOS Setup Main Menu Load Optimized Defaults Press lt Enter gt on this item and select Yes to load the optimal BIOS default settings The BIOS defaults settings help the system to operate in optimum state Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values Boot Override Allows you to select a device to boot immediately Press lt Enter gt on the device you select and select Yes to confirm Your system will restart automatically and boot from that device Save Profiles This function allows you to save the current BIOS settings to a profile You can create up to 8 profiles and save as Setup Profile 1 Setup Profile 8 Press lt Enter gt to complete Or you can select Select File in HDD USB FDD to save the profile to your storage device Load Profiles If your system becomes unstable and you have loaded the BIOS default settings you can use this function to load the BIOS settings from a profile created before without the hassles of reconfiguring the BIOS settings First select the profile you wish to load and then press lt Enter gt to complete You can select Select File in HDD USB FDD to input the profile previously created from your storage device or load the profile automatically created by the BIOS such as reverting the BIOS settings to the last settings that worked properly last known good record 99 Chapter 3 Appendix
28. gram enne 5 Chapter 1 Hardware Installation cccccccsscsssssssssssssscssssssseessessseessessseessesesesaseeseeeas 6 Fi ovs e d PRS CAUIIONS XXX 6 1 2 Product Specifications aeris iortee vista osten Ev versehen a Hinh atte Bud 7 je mu ING ihe CPU 9 1 4 Installing the Memory usas ecie rasta tbnso co eue Spb a FEXRE XE DG Reap a ana Xo beth ERUIT Rc inus 9 19 Installing an Expansion Bl eiit itia o ttt ide nre 10 16 Back Panel CORBIS lOS aasssasueneestena ieu DAD EY ex TER Resa drReRE etico i u 10 t7 mema COMME ClON Bisous eis tne te tcrtio a potet vec seis 11 Chapter 2 BIOS Setup ccssssssssssssssssssessessseesessseeseseeseessseesessesensesassesersassenersass 16 21 ic eel A a RET 16 PM 17 2 9 System Information saec t tnctisitur hme Darin eta rbd 21 24 BIOS FESUIBS een ene ere erent een Rue MN mU NND HERE ond 22 29 ic Umm 25 26 TOWEFIVISIOSOOIISTI cssssctniratisatutieiootineim esu tei bie saab auEe state Eu dci Pen REB EDEN E SEDE 2f PEE RN TT 29 CISION APPOSTO sparne e lima P NI eau Ee nU dd Rc 30 Divers MINS UN s o NR I Eo T 30 Regulatory Statements sissien a aiseria aie nnns 31 COE US a rte erent eer 32 GA H81 D3 Motherboard Layout ES 12V 2X4 CPU_FAN EERE LGA1150 gt Gnade Realtek COE LAN SYS FANT Lj PCIEX46 GA H81 D3 PCIEX1 1 PCIXE1 2 Intel H81 SATA3 0 1 PCI ridge SATA2 2
29. l GIGABYTE motherboards fulfill European Union regulations for RoHS Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment and WEEE Waste Electrical and Electronic Equipment environmental directives as well as most major worldwide safety requirements To prevent releases of harmful substances into the environment and to maximize the use of our natural resources GIGABYTE provides the following information on how you can responsibly recycle or reuse most of the materials in your end of life product Restriction of Hazardous Substances RoHS Directive Statement GIGABYTE products have not intended to add and safe from hazardous substances Cd Pb Hg Cr 6 PBDE and PBB The parts and components have been carefully selected to meet RoHS requirement Moreover we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals Waste Electrical amp Electronic Equipment WEEE Directive Statement GIGABYTE will fulfill the national laws as interpreted from the 2002 96 EC WEEE Waste Electrical and Electronic Equipment directive The WEEE Directive specifies the treatment collection recycling and disposal of electric and electronic devices and their components Under the Directive used equipment must be marked collected separately and disposed of properly WEEE Symbol Statement The symbol shown below is on the product or on its packaging which indicates
30. le1 Slot Sets the graphics card on the PCIEX16 slot as the first display Default PCI Sets the graphics card on the PCI slot as the first display XHCI Mode Allows you to determine the operating mode for the xHCI controller in OS gt gt Smart Auto This mode is available only when the BIOS supports the xHCI controller in the pre boot environment This mode is similar to Auto but it adds the capability to route the ports to xHCI or EHCI according to setting used in previous boots for non G3 boot in the pre boot environment This allows the use of USB 3 0 devices prior to OS boot xHCI controller enabling and rerouting should follow the steps in Auto when previous boot routs ports to EHCI Note This is the recommended mode when BIOS has xHCI pre boot support Default gt gt Auto BIOS routes the sharable ports to EHCI controller Then it uses ACPI protocols to provide an option to enable the xHCl controller and reroute the sharable ports 25 v Note This is the recommended mode when BIOS does NOT have xHCI pre boot support Enabled All shared ports are eventually routed to the xHCl controller during the BIOS boot process If BIOS does not have pre boot support for the xHCI controller it should initially route the sharable ports to the EHCI controller and then prior to OS boot it should route the ports to xHCI controller Note OS has to provide support for the xHCI controller in this mode If the OS does not provide suppo
31. ler Chip Hardware Monitor BIOS Ss 9 9 9 9 9 9 9 9 System voltage detection CPU System temperature detection CPU System fan speed detection CPU System overheating warning CPU System fan fail warning CPU System fan speed control Whether the fan speed control function is supported will depend on the cooler you install 2 x 64 Mbit flash Use of licensed AMI EFI BIOS Support for DualBIOS PnP 1 0a DMI 2 0 SM BIOS 2 6 ACPI 2 0a Unique Features Support for Q Flash Support for Xpress Install Support for APP Center Available applications in APP Center may differ by motherboard model Supported functions of each application may also differ depending on motherboard specifications BIOS EasyTune EZSetup USB Blocker Support for ON OFF Charge Bundled Software Norton Internet Security OEM version Operating System Support for Windows 8 1 8 7 f you plan to install Windows 8 1 please download the latest drivers from GIGABYTE s website fim Form Factor ATX Form Factor 30 5cm x 19 0cm GIGABYTE reserves the right to make any changes to the product specifications and product related information without prior notice Please visit the Support amp Downloads Utility page on GIGABYTE s website to check the supported operating system s for the software listed in the Unique Features and Bundled Software columns B 1 3
32. lues use a metal object like a screwdriver to touch the two pins for a few seconds CX Open Normal GE Short Clear CMOS Values A Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values After system restart go to BIOS Setup to load factory defaults select Load Optimized Defaults or manu ally configure the BIOS settings refer to Chapter 2 BIOS Setup for BIOS configurations 15 Chapter 2 BIOS Setup BIOS Basic Input and Output System records hardware parameters of the system in the CMOS on the motherboard Its major functions include conducting the Power On Self Test POST during system startup saving system parameters and loading operating system etc BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features When the power is turned off the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS To access the BIOS Setup program press the lt Delete gt key during the POST when the power is turned on To upgrade the BIOS use either the GIGABYTE Q Flash or BIOS utility Q Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system e BIOS is a Windows based utility that searches and downloads the latest version of BIOS from the Internet and updates the BIOS Beca
33. on a CPU power saving function in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption Auto lets the BIOS automatically configure this setting Default Auto C3 State Support Allows you to determine whether to let the CPU enter C3 mode in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption The C3 state is a more enhanced power saving state than C1 Auto lets the BIOS automatically configure this setting Default Auto C6 C7 State Support Allows you to determine whether to let the CPU enter C6 C7 mode in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption The C6 C7 state is a more enhanced power saving state than C3 Auto lets the BIOS automatically configure this setting Default Auto CPU Thermal Monitor Enables or disables Intel CPU Thermal Monitor function a CPU overheating protection function When enabled the CPU core frequency and voltage will be reduced when the CPU is overheated Note This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website 18 ww Auto lets the BIOS automatically configure this setting Default Auto CPU EIST Function
34. password or user password at system startup and when entering BIOS Setup Differing from the user password the administrator password allows you to make changes to all BIOS settings User Password Allows you to configure a user password Press lt Enter gt on this item type the password and then press lt Enter gt You will be requested to confirm the password Type the password again and press lt Enter gt You must enter the administrator password or user password at system startup and when entering BIOS Setup However the user password only allows you to make changes to certain BIOS settings but not all To cancel the password press lt Enter gt on the password item and when requested for the password enter the correct one first When prompted for a new password press lt Enter gt without entering any password Press lt Enter gt again when prompted to confirm 2 5 Peripherals GIGABYTE DualBIOS EF amp S ul e P m 3 4 LJ a TAS TIT System Information BIOS Features Pouer Management Save amp Exit Dashboard English Q Flash Initial Display Output PCIe 1 Smart Auto fiuto Enabled 64M MAX Enabled Enabled Disabled USB Storage Devices futo Enabled Initial Display Output Specifies the first initiation of the monitor display from the installed PCI graphics card PCI Express graphics card or the onboard graphics IGFX Sets the onboard graphics as the first display PC
35. r enter a sub menu Or you can use your mouse to select the item you want defaults EB When the system is not stable as usual select the Load Optimized Defaults item to set your system to its The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version 16 C167 1 2 410 DualBIOS 25 e gt EAM P System Information BIOS Features Peripherals Power Management Save amp Exit Dashboard English Q Flash gt M I T Current Status BIOS Version E BCLK 99 79MHz CPU Frequency 3605 85MHz Memory Frequency 1330 S6MHz Total Memory Size 2048MB CPU Temperature 41 0 C Ucore 1 044U DRAM Voltage 1 512U This section provides information on the BIOS version CPU base clock CPU frequency memory frequen Cy total memory size CPU temperature Vcore and memory voltage overall system configurations Incorrectly doing overclock overvoltage may result in damage to CPU chipset or memory and reduce the useful life of these components This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results Inad equately altering the settings may result in system s failure to boot If this occurs clear the CMOS values and reset the board to default values gt MIT Current Status This screen provides information on CPU memory frequencies parameters Advanced Frequency Settings Processor Graphics
36. rd Drive Activity LED HD Hard a I Connects to the power status indicator on the chassis front panel The LED is A System Status LED M E x S0 On 4z a a S3 S4 S5 Off A A o o on when the system is operating The PWR LED PWR LED PWR LED Ew Chassis Intrusion Header LED is off when the system is in 3 S4 sleep state or powered off S5 PW Power Switch Red Connects to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch refer to Chapter 2 BIOS Setup Power Management for more information e SPEAK Speaker Orange Connects to the speaker on the chassis front panel The system reports system startup status by issuing a beep code One single short beep will be heard if no problem is detected at system startup Drive Activity LED Blue Connects to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data RES Res et Switch Green Connects to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart e Cl Chass is Intrusion Header Gray Connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed This function requires a chassis with a chassis intrusion swi
37. rder from the available devices For example you can set hard drive as the first priority Boot Option 1 and DVD ROM drive as the second priority Boot Option 2 The list only displays the device with the highest priority for a specific type For example only hard drive defined as the first priority on the Hard Drive BBS Priorities submenu will be presented here Removable storage devices that support GPT format will be prefixed with UEFI string on the boot device list To boot from an operating system that supports GPT partitioning select the device prefixed with UEFI string Or if you want to install an operating system that supports GPT partitioning such as Windows 7 64 bit select the optical drive that contains the Windows 7 64 bit installation disk and is prefixed with UEFI string Bootup NumLock State Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST Default Enabled Security Option Specifies whether a password is required every time the system boots or only when you enter BIOS Setup After configuring this item set the password s under the Set Supervisor User Password item in the BIOS Main Menu Setup A password is only required for entering the BIOS Setup program System A password is required for booting the system and for entering the BIOS Setup 22 program Default Full Screen LOGO Show Allows you to determine whether to display the GIGABYTE Logo at system s
38. rical and electronic equipment minimize the use of landfills for the disposal of end of life products and generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly 31 Contact Us GIGA BYTE TECHNOLOGY CO LTD Address No 6 Bao Chiang Road Hsin Tien Dist New Taipei City 231 Taiwan TEL 886 2 8912 4000 FAX 886 2 8912 4005 Tech and Non Tech Support Sales Marketing http ggts gigabyte com tw WEB address English http www gigabyte com WEB address Chinese http www gigabyte tw You may go to the GIGABYTE website select your language in the language list on the top right corner of the website e GIGABYTE Global Service System c GIGABYTE t A f OQO Global Technical Service 5 To submit a technical or non technical Sales Marketing question please link to GIGASYIE Passport member please login with your http ggts gigabyte com tw membership E Mail address and password t erwise you can simply enter E Mail address to login Then select your language to enter the system Yen Email 1 O assword MEN VU e d Engish fx f Deutsch J Francais f Polski f Espa ol 99
39. rleaving Rank Interleaving and memory timing settings below to be configurable Options are Auto default Manual Advanced Manual Profile DDR Voltage When using a non XMP memory module or Extreme Memory Profile X M P is set to Disabled this item will display as 1 50V When Extreme Memory Profile X M P is set to Profile or Profile2 this item will display the value based on the SPD data on the XMP memory Channel Interleaving Enables or disables memory channel interleaving Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability Auto lets the BIOS automatically configure this setting Default Auto Rank Interleaving Enables or disables memory rank interleaving Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability Auto lets the BIOS automatically configure this setting Default Auto Note 1 This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website Note 2 This item is present only when you install a memory module that supports this feature 19 gt Channel A B Memory Sub Timings This sub menu provides memory timing settings for each channel of memory The respective timing setting screens are configurable only when Memory Timing Mode is set to Manual or Advanced Man
40. rt all sharable ports won t work gt Disabled The USB 3 0 ports are routed to the EHCI controller and the xHCI controller is turned off All USB 3 0 devices function as High Speed devices regardless of xHCI software support availability Manual Allows you to determine whether to rout the USB 3 0 ports to the xHCI or EHCI controller before booting to OS and also provides you with options to manually rout each USB 3 0 2 0 port to xHCI or EHCI Audio Controller Enables or disables the onboard audio function Default Auto If you wish to install a 3rd party add in audio card instead of using the onboard audio set this item to Disabled Intel Processor Graphics Enables or disables the onboard graphics function Default Enabled Intel Processor Graphics Memory Allocation Allows you to set the onboard graphics memory size Options are 32M 1024M Default 64M DVMT Total Memory Size Allows you to allocate the DVMT memory size of the onboard graphics Options are 128M 256M MAX Default MAX Legacy USB Support Allows USB keyboard mouse to be used in MS DOS Default Enabled XHCI Hand off Determines whether to enable XHCI Hand off feature for an operating system without XHCI Hand off support Default Enabled EHCI Hand off Determines whether to enable EHCI Hand off feature for an operating system without EHCI Hand off support Default Disabled USB Storage Devices Displays a list of connected USB mass storage
41. stickers are required for warranty valida tion Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components When connecting hardware components to the internal connectors on the motherboard make sure they are connected tightly and securely When handling the motherboard avoid touching any metal leads or connectors It is best to wear an electrostatic discharge ESD wrist strap when handling electronic components such as a motherboard CPU or memory If you do not have an ESD wrist strap keep your hands dry and first touch a metal object to eliminate static electricity Prior to installing the motherboard please have it on top of an antistatic pad or within an electrostatic shielding container Before unplugging the power supply cable from the motherboard make sure the power supply has been turned off Before turning on the power make sure the power supply voltage has been set according to the local voltage standard Before using the product please verify that all cables and power connectors of your hard ware components are connected To prevent damage to the motherboard do not allow screws to come in contact with the motherboard circuit or its components Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing Do not place the computer system on an uneven surface Do not place th
42. tartup Disabled skips the GIGABYTE Logo when the system starts up Default Enabled Fast Boot Enables or disables Fast Boot to shorten the OS boot process Ultra Fast provides the fastest bootup speed Default Disabled VGA Support Allows you to select which type of operating system to boot gt Auto Enables legacy option ROM only gt gt EFI Driver Enables EFI option ROM Default This item is configurable only when Fast Boot is set to Enabled or Ultra Fast USB Support gt gt Disabled All USB devices are disabled before the OS boot process completes gt gt Full Initial All USB devices are functional in the operating system and during the POST gt gt Partial Initial Part of the USB devices are disabled before the OS boot process completes Default This item is configurable only when Fast Boot is set to Enabled This item is disabled when Fast Boot is set to Ultra Fast PS2 Devices Support gt gt Disabled All PS 2 devices are disabled before the OS boot process completes gt Enabled All PS 2 devices are functional in the operating system and during the POST Default This item is configurable only when Fast Boot is set to Enabled This item is disabled when Fast Boot is set to Ultra Fast NetWork Stack Driver Support gt Disabled Disables booting from the network Default gt Enabled Enables booting from the network This item is configurable only when Fast Boot is set to Enabled or Ultra Fast
43. tch sensor The front panel design may differ by chassis A front panel module mainly consists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly 13 8 9 F AUDIO Front Panel Audio Header The front panel audio header supports Intel High Definition audio HD and AC 97 audio You may connect your chassis front panel audio module to this header Make sure the wire assignments of the module connector match the pin assignments of the motherboard header Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it For HD Front Panel Audio For AC 97 Front Panel Audio Pin No Definition Pin No Definition 9 1 1 MIC2_L 1 MIC k 2 GND 2 GND 3 MIC2 R 3 MIC Power 10 2 4 ACZ DET 4 NC 5 LINE2 R 5 Line Out R 6 GND 6 NC 1 FAUDIO JD 7 NC 8 No Pin 8 No Pin 9 LINE2_L 9 Line Out L 10 GND 10 NC Audio signals will be present on both of the front and back panel audio connections simultaneously Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug For information about connecting the front panel audio module that has different wire as
44. that this product a must not be disposed of with other waste Instead the device should be taken to the waste collection centers for activation of the treatment collection recycling and disposal procedure The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local government office your household waste disposal service or where you purchased the product for details of environmentally safe recycling When your electrical or electronic equipment is no longer useful to you take it back to your local or regional waste collection administration for recycling f you need further assistance in recycling reusing in your end of life product you may contact us at the Customer Care number listed in your product s user s manual and we will be glad to help you with your effort Finally we suggest that you practice other environmentally friendly actions by understanding and using the energy saving features of this product where applicable recycling the inner and outer packaging including shipping containers this product was delivered in and by disposing of or recycling used batteries properly With your help we can reduce the amount of natural resources needed to produce elect
45. tor This section provides information on your motherboard model and BIOS version You can also select the default language used by the BIOS and manually set the system time System Language Selects the default language used by the BIOS System Date Sets the system date The date format is week read only month date and year Use Enter to switch between the Month Date and Year fields and use the Page Up or Page Down key to set the desired value a 274 System Time Sets the system time The time format is hour minute and second For example 1 p m is 13 0 0 Use Enter to switch between the Hour Minute and Second fields and use the Page Up or Page Down key to set the desired value Access Level Displays the current access level depending on the type of password protection used If no password is set the default will display as Administrator The Administrator level allows you to make changes to all BIOS settings the User level only allows you to make changes to certain BIOS settings but not all 2 4 BIOS Features GIGABYTE DualBIOS e A S f c TIT System Information Peripherals Pouer Management Save amp Exit Dashboard English Q Flash Boot Option 1 UEFI fi ADATA U Enabled System Enabled Disabled Disabled Enabled Enabled Disabled Enabled Other 0S UEFI an Disabled Legacy UEFI OpROM Boot Option Priorities Specifies the overall boot o
46. ual Note Your system may become unstable or fail to boot after you make changes on the memory timings If this oc curs please reset the board to default values by loading optimized defaults or clearing the CMOS values gt Advanced Voltage Settings This sub menu allows you to set CPU chipset and memory voltages gt E PC Health Status Reset Case Open Status Disabled Keeps or clears the record of previous chassis intrusion status Default gt Enabled Clears the record of previous chassis intrusion status and the Case Open field will show No at next boot Case Open Displays the detection status of the chassis intrusion detection device attached to the motherboard Cl header If the system chassis cover is removed this field will show Yes otherwise it will show No To clear the chassis intrusion status record set Reset Case Open Status to Enabled save the settings to the CMOS and then restart your system CPU Vcore CPU VRIN DRAM Voltage 3 3V 5V 12V CPU VAXG Displays the current system voltages CPU System Temperature Displays current CPU system temperature CPU System Fan Speed Displays current CPU system fan speeds CPU System Temperature Warning Sets the warning threshold for CPU system temperature When temperature exceeds the threshold BIOS will emit warning sound Options are Disabled default 60 C 140 F 70 C 158 F 80 C 176 F 90 C 194 F CPU System Fan Fail Warning Allows
47. use BIOS flashing is potentially risky if you do not encounter problems using the current version of A BIOS it is recommended that you not flash the BIOS To flash the BIOS do it with caution Inadequate BIOS flashing may result in system malfunction e tis recommended that you not alter the default settings unless you need to to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs try to clear the CMOS values and reset the board to default values Refer to the Load Optimized Defaults section in this chapter or introductions of the battery clear CMOS jumper in Chapter 1 for how to clear the CMOS values 2 1 Startup Screen The following startup Logo screen will appear when the computer boots Sample BIOS Version E7 GIGABYTE insiston TRA Function Keys Differing from traditional UEFI interface the Dashboard Mode provides a fancy and user friendly BIOS environment where users can easily point and click through various settings and make adjustments for optimum performance In Dashboard Mode you can use your mouse to move through the option menus for quick configuration or you can click Classic Setup under the Shortcuts list on the right of the screen or press lt F2 gt to switch to the traditional BIOS Setup screen On the main menu of the BIOS Setup program press arrow keys to move among the items and press lt Enter gt to accept o
48. y brand speed and chips be used for optimum performance m 1 5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card A e Make sure the motherboard supports the expansion card Carefully read the manual that came with your expansion card Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage 1 6 Back Panel Connectors e PS 2Keyboard and PS 2 Mouse Port Use the upper port green to connect a PS 2 mouse and the lower port purple to connect a PS 2 keyboard Parallel Port Use the parallel port to connect devices such as a printer scanner and etc The parallel port is also called a printer port Serial Port Use the serial port to connect devices such as a mouse modem or other peripherals D Sub Port The D Sub port supports a 15 pin D Sub connector and supports a maximum resolution of 1920x1200 the actual resolutions supported depend on the monitor being used Connect a monitor that supports D Sub connection to this port USB 3 0 2 0 Port The USB 3 0 port supports the USB 3 0 specification and is compatible to the USB 2 0 1 1 specification Use this port for USB devices such as a USB keyboard mouse USB printer USB flash drive and etc Speed LED ActivtyLep Connection Speed LED Activity LED State Description State Description 1 ma Orange 1 G
Download Pdf Manuals
Related Search